1
INSTALLATION INSTRUCTIONS
PD-64114
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
!
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
"#$%&'#()*+,-*.*+//
0
01--2&3&4
056,((-(56--
0
&$&7'(#(-2(((
-891(2(-8
9(:-((-,2)2- ;-
(
$&#&&&%#'-(56
656)-22+22
$1&7'<)<,;):)
0;)=
0->?<(<<<=<<3&4,<6
>6
0(,=((-;(#;(
##&#$%&'#(>)?<<(@(?<
)(>(?<)(89((>@
((89((<(<=
A;)<(><
&%#=&##$&'B>(<6<&
6;B>-66)
Wire Connector
Qty: 5pcs+1 Extra
Mounting Screw
Qty: 1 Extra
AB
2
INSTALLATION INSTRUCTIONS
PD-64114
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
!
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
#$%&
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
%"&#$&7#9$C#"39/
3. Remove the mounting screw (B) from the xture.
4. Secure the mounting plate to the junction box using standard junction
box screws .
&%#'(i) using any other non-original-manufacturer provided junction
box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
5. Choose number of rods suitable for your application.
6. Thread the xture wire through the rods, swivel and canopy.
7. Attach the canopy, rods, swivel and lamp body. Ensure all are tightened.
&%#'Due to limited space within the canopy, shorten the cable as
necessary to make the installation easier. Make sure to identify and label all
the wiring properly before any trimming/shortening. (Fig. 3)
%&&#$&7#$139/D9/E
8. Connect the driver’s output wires to xture wire as shown in Fig. 3, red
to the red, and black to the black, make sure that wire connectors (A) are
secured. Then tuck them inside the canopy.
9. Connect the driver’s input wires to junction box wires as shown in Fig. 2,
making sure that all wire connectors (A) are secured. If your outlet box has a
green or bare copper ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the back plate using
the screw provided. After wires are connected, tuck them carefully inside
the junction box.
%#$&7#$&1##$%&
10. Secure the xture by mounting the canopy to the mounting back plate.
Slide the canopy in the derection of the notch until it latches in place. Fasten
the canopy to the mounting back plate using the mounting screw (B) .
11. For slope ceiling application, rotate swivel at the top of the stem to
ensure luminaire is aiming down (Fig. 4).
/
9$7
9$7D/ 9$7
Turn to down
Black or
Smooth
White or
Ribbed
Bare wire
(Ground)
Black
(Hot)
White
(Neutral)
Green or Bare Copper
(Ground)
9$7E)/
3×RPL-RODIN12-886-BN
1×RPL-RODIN06-886-BN
Junction Box
Ground Wire
A
Wire Connector
Junction Box
Screw
Canopy
Mounting Plate
B
Mounting Screw
Driver
Swivel
Lamp Body
RPL-RODIN06-886-BK
RPL-RODIN12-886-BK
4 1/4”
1 3/8”
1 3/4”
4"
White - Neutral
Black - Hot
Red +
Black -
Red +
Black -
Driver
Input
Output
Canopy
/