Ono Sokki GS-1830A User manual

Brand
Ono Sokki
Model
GS-1830A
Type
User manual
400×297 mm （10 折）
B00002364 / IM13092401 (1.0) 139 (MS) 000
ONO SOKKI CO., LTD.
CAUTION
Recommended tightening torque: 0.4 to 0.5N･m
M4 screw
Collar
+ 0.018
0
+ 0.018
0
φ15H7
Approximately 0.2 mm
Approximately
0.2 mm
M3 screw
Spring
washer
Tightening torque
（N･m）
0.7
0.52
Fixing jig
(female screw)
Iron
Aluminum
M3 screw
(male screw)
Iron
Iron
1.3 mm or less
Mounting surface
Base bottom
ø15H7
ø17
ø18
1.5（slot）
14
14.5
Recommended collar size and material
Material: Brass
Recommended screw : Ｍ4
Recommended tightening torque : 0.4 to 0.5N･m
22Ω
22Ω
A
B
C
D
E
F
SIG 1
SIG 2
Vcc
N.C.
COM
COM
R03-PB6M (TAJIMI ELECTRONICS)
Linear gauge sensor
P
SIG 1
SIG 2
hen pushing spindle in
P
=
40μm ： GS-1700A/6700A Series
P
=
4μm ： GS-1800A/6800A Series
P
SIG 1
SIG 2
When pulling spindle out
+5V
+5V IN
Frame
Connector outer tube
+5V 200mA
CAUTION
LINEAR GAUGE SENSOR 13mm
Spanner
Dust-protective rubber
Gauge head
Flat part
Parting line
B on gauge head side
A on stem side
Causes CountermeasuresPhenomena
Nonsmooth spindle
movement
Unstable measurement
values
Do not tighten the step with excessive force.
The dust-protective rubber does not have sufficient resistance to
oil or chemicals. After the duct-protective rubber is replaced
with a new one, take measures for protecting it against oil and
chemicals.
Fix securely the gauge sensor.
Mount securely the gauge head.
Position the sensor cable as far as possible from noise generation
sources such as power line and switching surge.
Suppress vibration and shock given to the gauge sensor as much
as possible.
The stem is mounted with excessive force.
The dust-preventive rubber is deteriorated by
oil and/or chemicals.
The gauge sensor is not secured.
The gauge head is mounted loose.
Noise
Excessive vibration, shock or acceleration
TAJIMI ELECTRONICS
R03-PB6M
Cable length
Approximately 1.9m
Mounting surface
TAJIMI ELECTRONICS
R03-PB6M
Mounting surface
Cable length
Approximately
1.9m
Items
Measurement range （mm）
Resolution （μm）
Accuracy （μm）
GS-1713A/6713A
13
10
3 ＊1
1 (4) ＊2
1.3
GS-1730A/6730A
30
10
3 ＊1
1 (4) ＊2
1.9
GS-1813A/6813A
13
1
2 ＊1
0.3 (1.2) ＊2
1.3
GS-1830A/6830A
30
1
3 ＊1
0.3 (1.2) ＊2
1.9
GS-1813A/6813A GS-1830A/6830A
4.5 to 5.5VDC
120mA or less (5VDC)
Two-phase square wave signal with
phase difference 90°±20°
Approximately 22Ω
98 m/s2 in each of three axes (75 minutes per each), 10 cycles of 10 to 150Hz sweeping
147 m/s2 in each of three axes (75 minutes per each), 10 cycles of 10 to 150Hz sweeping
980 m/s2 in each direction for each of three axes, 3 times for each of ±X, Y and Z, 18 times in total, sine half-wave, 6ms operating time
1471 m/s2 in each direction for each of three axes, 3 times for each of ±X, Y and Z, 18 times in total, sine half-wave, 6ms operating time
・ Air lifter ： AA-6102（13 mm）/AA-6103（30 mm）
・ Finger lift ： AA-969
・ Gauge stand ： ST-0230/044B
・ Dust-protective rubber (spare) ： AA-4102（13 mm）/AA-4103（30 mm）
0 ℃ to +40 ℃
-10°C to +55°C (average annual humidity 75% or less) * No condensation permitted
Approximately 1.9m ＊4
Up to 30m ＊5
GS-1713A/1813/A6713A/6813A: Approximately 250g,
GS-1730A/1830A/6730/A6830A: Approximately 310g (including cable)
Instructions Manual (this manual) x1, Spanner x1, Spacer x1 (only GS-1813)
IP-64
GS-1730A/6730AGS-1713A/6713A
Operating temperature range
Storage temperature range
Cable length
Cable extension
Mass
Accessories
Protection Class
Options
* See the catalog
for details.
Items
Supplied power
Consumption current
Signal output
Output impedance
＊4　Signal cable connector disconnection or remodeling will invalidate CE marking.
＊5　20m when EMC applicable cable AA-8803 is used.
＊1 At 20 degrees C.
＊2 Value with our gauge counter used
A value enclosed in ( ) is the maximum response speed for DG-4140/4160.
＊3 Vibration/shock resistance of mechanical specifications during measurement are not guaranteed.
GS-17/18 Series
GS-67/68 Series
GS-17/18 Series
GS-67/68 Series
Measuring force in
downward direction （N）
Max. response
speed （m/s）
  • Page 1 1
  • Page 2 2

Ono Sokki GS-1830A User manual

Brand
Ono Sokki
Model
GS-1830A
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents