AEM All CD-5 and CD-7 Dashes Operating instructions

Brand: AEM

Model: All CD-5 and CD-7 Dashes

Type: Operating instructions

AEM All CD-5 and CD-7 Dashes are versatile, high-performance digital dashboards designed for racing and automotive enthusiasts. With a large, sunlight-readable display and intuitive interface, they provide real-time data and control over various vehicle systems. These dashes offer advanced features such as customizable layouts, multiple screen configurations, and the ability to display a wide range of data channels. Whether you're a professional racer or a weekend enthusiast, these dashes can enhance your driving experience and provide valuable insights into your vehicle's performance.

Revision

Date

Initial Release

Mar 9, 2017

Performance Electronics PE3 Series ECUs to CD-7 Displays

Supported ECU’s

PE3-8400

PE3-8405

PE3-SP000

Supported Channels

AEM supports the following 65 channels transmitted by the PE3 ECUs.

Note: not all ECU’s transmit all channels.

EngineSpeed ThrottlePos FuelInjPulsewidth

IgnitionTiming BaroPress IntakeManifoldAirPress

AFRAverage AFR1 AFR2

AFRTarget ECUPressureUnits ECUAnalogInput1Voltage

ECUAnalogInput2Voltage ECUAnalogInput3Voltage ECUAnalogInput4Voltage

ECUAnalogInput5Voltage ECUAnalogInput6Voltage ECUAnalogInput7Voltage

ECUAnalogInput8Voltage ECUFrequency1 ECUFrequency2

ECUFrequency3 ECUFrequency4 ECUBatteryVoltage

IntakeManifoldAirTemp CoolantTemp ECUTemperatureUnits

ECUThermisterInput5Temp ECUThermisterInput7Temp ECUVersionMajor

ECUVersionMinor ECUVersionBuild EngineSpeedRateofChange

ThrottlePosRateofChange MAPRateofChange MAFRateofChange

ECUPWMDuty1 ECUPWMDuty2 ECUPWMDuty3

ECUPWMDuty4 ECUPWMDuty5 ECUPWMDuty6

ECUPWMDuty7 ECUPWMDuty8 TracControlSlipMeasured

WheelSpeedAvgDrivenRateofChange TracControlSlipTarget WheelSpeedAvgDriven

WheelSpeedAvgNonDriven TracControlIgnOffsetRequest TracControlIgnCutRequest

WheelSpeedDriven1 WheelSpeedDriven2 WheelSpeedNonDriven1

WheelSpeedNonDriven2 FuelInjCompAccel FuelInjCompStarting

FuelInjCompAirTemp FuelInjCompCltTemp FuelInjCompBaroPress

FuelInjCompManifoldPress IgnitionTrimAirTemp IgnitionTrimCoolantTemp

IgnitionTrimBaroPress IgnitionTrimManifoldPress

CAN Bus Wiring

AEM CD7 has 2 separate CAN ports. For 3

party devices, AEM recommends you use AEM CAN

BUS 2, whose connections are contained in an unterminated twisted/shielded lead in the dash loom.

PE3-84XX CAN High (C-08)  AEM CD7 Pin 5 (CAN 2+), Gray wire in twisted/shielded pair

PE3-84XX CAN Low (C-07)  AEM CD7 Pin 6 (CAN 2-), Black wire in twisted/shielded pair

PE3-SP000 CAN High (A-10)  AEM CD7 Pin 5 (CAN 2+), Gray wire in twisted/shielded pair

PE3-SP000 CAN Low (A-03)  AEM CD7 Pin 6 (CAN 2-), Black wire in twisted/shielded pair

AEM Setup in DashDesign

You can either start with a new dash layout by selecting “File” then “New” in DashDesign or you can

select from a pre-designed layout that has screens already designed and inserted but has the CAN

inputs left blank. These are chosen by selecting “File” then “Open” and selecting one of the setups

titled xzyblank.aemcd7 with the xyz representing a description of the layouts contained in the file.

To import the CAN configuration into your setup you select “Setup” then “Display” from the main

DashDesign menu. Once the dialog box opens you select the “CAN Receive” tab.

Change the settings to the following:

Show: “Port 2”

Baudrate: 250 kbit/s

Termination Resistor: “ON”

Address Mask: “OFF”

M800 Support: “OFF”

Then click on “Import CAN” on the lower left and select the can setup file. The new items will appear

in the Outputs tab. They can now be viewed on the display or logged. You can rename, filter, or

manipulate any of these channels to make them more useful.

AEM All CD-5 and CD-7 Dashes Operating instructions

AEM All CD-5 and CD-7 Dashes Operating instructions

AEM All CD-5 and CD-7 Dashes Operating instructions

Related papers

Other documents