H3C S5120-EI Series Command Reference Manual

H3C S5120-EI Series Ethernet Switches

Fundamentals Command Reference

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Software version: Release 2208

Document version: 6W100-20101224

No part of this manual may be reproduced or transmitted in any form or by any means

without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C,

, Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot, Neocean,

NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG,

V

2

G, V

n

G, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their

respective owners

Notice

The information in this document is subject to change without notice. Every effort has been

made in the preparation of this document to ensure accuracy of the contents, but all

statements, information, and recommendations in this document do not constitute the

warranty of any kind, express or implied.

Preface

The H3C S5120-EI documentation set includes 10 command references, which describe the

commands and command syntax options for the S5120-EI Series Ethernet Switches,

Release2208.

The Fundamentals Command Reference describes commands for configuring command

line interface (CLI), logging in to your switch, configuring FTP and TFTP, file system

management, configuration file management, device management, and software

upgrade.

This preface includes:

•

Audience

•

Added and modified commands

•

Conventions

•

About the H3C S5120-EI documentation set

•

Obtaining documentation

•

Technical support

•

Documentation feedback

Audience

This documentation is intended for:

• Network planners

• Field technical support and servicing engineers

• Network administrators working with the S5120-EI series

Added and modified commands

Compared to Release2202, Release2208 adds and modifies the following commands:

Command reference Added and modified commands

CLI

Added commands: super authentication-mode

Modified commands: Added regular-expression related

parameters to all display commands

Logging In to the Switch

Added commands:

• command authorization

• command accounting

FTP —

TFTP —

File Management —

Configuration File

Management

Modified commands: save—Added support for the force

keyword

Software Upgrade Added commands: boot-loader update file

Command reference Added and modified commands

Device Management

Added commands:

• job

• time at

• time delay

• view

• temperature-limit

Conventions

This section describes the conventions used in this documentation set.

Command conventions

Convention Description

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ]

Square brackets enclose syntax choices (keywords or arguments) that are

optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars,

from which you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical

bars, from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by

vertical bars, from which you select at least one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated

by vertical bars, from which you may select multiple choices or none.

&<1-n>

The argument or keyword and argument combination before the ampersand

(&) sign can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface.

For example, the New User window appears; click OK.

>

Multi-level menus are separated by angle brackets. For example, File > Create

> Folder.

Symbols

Convention Description

WARNING

An alert that calls attention to important information that if not understood or

followed can result in personal injury.

CAUTION

An alert that calls attention to important information that if not understood or

followed can result in data loss, data corruption, or damage to hardware or

software.

IMPORTANT

An alert that calls attention to essential information.

NOTE

An alert that contains additional or supplementary information.

TIP

An alert that provides helpful information.

About the H3C S5120-EI documentation set

The H3C S5120-EI documentation set includes:

Category Documents Purposes

Marketing brochures Describe product specifications and benefits.

Technology white papers

Provide an in-depth description of software

features and technologies.

RPS User Manual

Describes the appearances, features, and

specifications of the RPS units available for the

products.

RPS Ordering Information for

H3C Low-End Ethernet

Switches

Provides the RPS and switch compatibility matrix

and RPS cable specifications.

H3C Low End Series Ethernet

Switches Pluggable Modules

Manual

Describes the models, appearances, and

specifications of the pluggable modules

available for the products.

Product

description

and

specifications

Interface Card User Manual

Describes the appearance and specifications

of interface cards.

Installation Manual

Provides a complete guide to hardware

installation and hardware specifications.

Provides regulatory information and the safety

instructions that must be followed during

installation.

Pluggable SFP[SFP+][XFP]

Transceiver Modules

Installation Guide

Guides you through installing SFP/SFP+/XFP

transceiver modules.

Hardware

installation

Interface Card User Manual Describes how to install an interface card.

Configuration guides

Describe software features and configuration

procedures.

Software

configuration

Command references

Provide a quick reference to all available

commands.

H3C Series Ethernet Switches

Login Password Recovery

Manual

Describes how to find or recover a lost

password.

Operations

and

maintenance

Release notes

Provide information about the product release,

including the version history, hardware and

software compatibility matrix, version upgrade

information, technical support information, and

software upgrading.

Obtaining documentation

You can access the most up-to-date H3C product documentation on the World Wide Web

at

http://www.h3c.com.

Click the links on the top navigation bar to obtain different categories of product

documentation:

[Technical Support & Documents > Technical Documents] – Provides hardware installation,

software upgrading, and software feature configuration and maintenance

documentation.

[Products & Solutions] – Provides information about products and technologies, as well as

solutions.

[Technical Support & Documents > Software Download] – Provides the documentation

released with the software version.

Technical support

[email protected]

http://www.h3c.com

Documentation feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

i

Contents

CLI configuration commands······································································································································· 1

CLI configuration commands ···········································································································································1

command-alias enable·············································································································································1

command-alias mapping ·········································································································································1

command-privilege level ··········································································································································2

display clipboard ·····················································································································································3

display command-alias ············································································································································4

display history-command ·········································································································································4

display hotkey···························································································································································5

hotkey ········································································································································································6

quit ·············································································································································································8

return··········································································································································································8

screen-length disable················································································································································9

super ··········································································································································································9

super authentication-mode···································································································································· 10

super password ····················································································································································· 11

system-view ···························································································································································· 12

Logging in to the switch commands··························································································································13

Logging in to the switch commands ····························································································································· 13

acl (user interface view)········································································································································ 13

activation-key ························································································································································· 14

auto-execute command ········································································································································· 15

authentication-mode·············································································································································· 16

command accounting············································································································································ 17

command authorization········································································································································ 18

databits··································································································································································· 19

display ip http ························································································································································ 19

display ip https ······················································································································································ 20

display user-interface ············································································································································ 21

display users ·························································································································································· 23

display web users·················································································································································· 25

escape-key······························································································································································ 25

flow-control····························································································································································· 26

free user-interface ·················································································································································· 27

free web-users························································································································································ 28

history-command max-size···································································································································· 29

idle-timeout ····························································································································································· 29

ip http acl ······························································································································································· 30

ip http enable························································································································································· 31

ip http port······························································································································································ 31

ip https acl······························································································································································ 32

ip https certificate access-control-policy ·············································································································· 33

ip https enable ······················································································································································· 33

ip https port ···························································································································································· 34

ip https ssl-server-policy········································································································································· 35

lock·········································································································································································· 35

parity······································································································································································· 36

protocol inbound ··················································································································································· 37

ii

screen-length ·························································································································································· 37

send ········································································································································································ 38

set authentication password································································································································· 39

shell········································································································································································· 40

speed (user interface view)··································································································································· 40

stopbits···································································································································································· 41

telnet ······································································································································································· 42

telnet ipv6······························································································································································· 43

telnet server enable ··············································································································································· 43

terminal type ·························································································································································· 44

user privilege level ················································································································································ 44

user-interface·························································································································································· 45

FTP configuration commands ····································································································································47

FTP server configuration commands····························································································································· 47

display ftp-server···················································································································································· 47

display ftp-user······················································································································································· 48

free ftp user ···························································································································································· 49

ftp server acl ·························································································································································· 49

ftp server enable···················································································································································· 50

ftp timeout······························································································································································· 50

ftp update······························································································································································· 51

FTP client configuration commands······························································································································ 51

ascii········································································································································································· 52

binary ····································································································································································· 52

bye ·········································································································································································· 53

cd ············································································································································································ 53

cdup········································································································································································ 54

close········································································································································································ 55

debugging······························································································································································ 55

delete ······································································································································································ 57

dir············································································································································································ 57

disconnect ······························································································································································ 58

display ftp client configuration····························································································································· 59

ftp ············································································································································································ 59

ftp client source······················································································································································ 60

ftp ipv6 ··································································································································································· 61

get ··········································································································································································· 62

lcd ··········································································································································································· 63

ls·············································································································································································· 64

mkdir······································································································································································· 65

open········································································································································································ 65

open ipv6······························································································································································· 66

passive···································································································································································· 67

put ··········································································································································································· 67

pwd········································································································································································· 68

quit ·········································································································································································· 69

remotehelp ····························································································································································· 69

rmdir ······································································································································································· 71

user ········································································································································································· 72

verbose ··································································································································································· 73

TFTP configuration commands···································································································································74

TFTP client configuration commands ···························································································································· 74

display tftp client configuration···························································································································· 74

iii

tftp-server acl·························································································································································· 74

tftp ··········································································································································································· 75

tftp client source····················································································································································· 77

tftp ipv6 ·································································································································································· 78

File management commands·····································································································································79

File management commands ········································································································································ 79

cd ············································································································································································ 79

copy ········································································································································································ 80

delete ······································································································································································ 80

dir············································································································································································ 81

execute ··································································································································································· 83

file prompt ······························································································································································ 83

fixdisk······································································································································································ 84

format······································································································································································ 84

mkdir······································································································································································· 85

more········································································································································································ 86

move ······································································································································································· 87

pwd········································································································································································· 87

rename···································································································································································· 88

reset recycle-bin····················································································································································· 88

rmdir ······································································································································································· 90

undelete·································································································································································· 90

Configuration file management commands ·············································································································92

Configuration file management commands ················································································································ 92

archive configuration ············································································································································ 92

archive configuration interval ······························································································································ 92

archive configuration location ····························································································································· 93

archive configuration max···································································································································· 94

backup startup-configuration································································································································ 95

configuration replace file······································································································································ 96

display archive configuration······························································································································· 97

display current-configuration································································································································ 98

display default-configuration································································································································ 99

display saved-configuration ·······························································································································100

display startup ·····················································································································································102

display this ···························································································································································103

reset saved-configuration····································································································································105

restore startup-configuration·······························································································································106

save·······································································································································································106

slave auto-update config·····································································································································109

startup saved-configuration ································································································································109

Software upgrade commands································································································································ 111

Software upgrade commands·····································································································································111

boot-loader···························································································································································111

boot-loader update file ·······································································································································112

bootrom ································································································································································113

bootrom-update security-check enable··············································································································114

display boot-loader ·············································································································································115

display patch information···································································································································116

patch active··························································································································································117

patch deactive ·····················································································································································117

patch delete ·························································································································································118

patch install··························································································································································118

iv

patch load····························································································································································119

patch location ······················································································································································120

patch run ······························································································································································120

Device management commands ···························································································································· 121

Device management commands·································································································································121

clock datetime······················································································································································121

clock summer-time one-off···································································································································122

clock summer-time repeating······························································································································123

clock timezone·····················································································································································124

copyright-info enable ··········································································································································125

display clock ························································································································································126

display cpu-usage················································································································································127

display cpu-usage history ···································································································································129

display device······················································································································································131

display device manuinfo·····································································································································132

display diagnostic-information ···························································································································133

display environment ············································································································································134

display fan ···························································································································································135

display job ···························································································································································136

display memory ···················································································································································137

display power······················································································································································138

display reboot-type··············································································································································139

display rps····························································································································································140

display schedule job ···········································································································································140

display schedule reboot······································································································································141

display system-failure ··········································································································································142

display transceiver ··············································································································································143

display transceiver alarm ···································································································································144

display transceiver diagnosis·····························································································································147

display transceiver manuinfo ·····························································································································148

display version·····················································································································································149

header ··································································································································································150

job·········································································································································································152

reboot ···································································································································································152

reset unused porttag············································································································································153

schedule job·························································································································································154

schedule reboot at···············································································································································155

schedule reboot delay·········································································································································157

shutdown-interval·················································································································································158

startup bootrom-access enable···························································································································158

sysname································································································································································159

system-failure························································································································································160

temperature-limit ··················································································································································160

time at···································································································································································161

time delay·····························································································································································162

view ······································································································································································163

Index ········································································································································································ 165

1

CLI configuration commands

command-alias enable

Syntax

command-alias enable

undo command-alias enable

View

System view

Default level

2: System level

Parameters

None

Description

Use the command-alias enable command to enable the command alias function.

Use the undo command-alias enable command to disable the command alias function.

By default, the command alias function is disabled.

Examples

# Enable the command alias function.

<Sysname> system-view

[Sysname] command-alias enable

# Disable the command alias function.

<Sysname> system-view

[Sysname] undo command-alias enable

command-alias mapping

Syntax

command-alias mapping cmdkey alias

undo command-alias mapping cmdkey

View

System view

Default level

2: System level

2

Parameters

cmdkey: The complete form of the first keyword of a command.

alias: Specifies the command alias, which cannot be the same as the first keyword of an existing

command.

Description

Use the command-alias mapping command to configure command aliases.

Use the undo command-alias mapping command to delete command aliases.

By default, a command has no alias.

Examples

# Configure command aliases by specifying show as the replacement of the display keyword.

<Sysname> system-view

[Sysname] command-alias mapping display show

After you configure the command aliases, the display commands have aliases. For example, if the

original command is display clock, now its alias is show clock and you can input the alias to view the

system time and date.

# Delete the command aliases by canceling the replacement of the display keyword.

<Sysname> system-view

[Sysname] undo command-alias mapping display

command-privilege level

Syntax

command-privilege level level view view command

undo command-privilege view view command

View

System view

Default level

3: Manage level

Parameters

level level: Command level, which ranges from 0 to 3.

view view: Specifies a view.

command: Command to be set in the specified view.

Description

Use the command-privilege command to assign a level for the specified command in the specified view.

Use the undo command-privilege view command to restore the default.

By default, each command in a view has a specified level.

Command levels include four privileges: visit (0), monitor (1), system (2), and manage (3). You can

assign a privilege level according to the user’s need. When logging in to the switch, the user can access

the assigned level and all levels below it.

3

• Level changes can cause maintenance, operation, and security problems. H3C recommends that

you use the default command level or that you modify the command level under the guidance of

professional staff.

• The command specified in the command-privilege command must be complete, and has valid

arguments. For example, the default level of the tftp server-address { get | put | sget }

source-filename [ destination-filename ] [ source { interface interface-type interface-number | ip

source-ip-address } ] command is 3. After the command-privilege level 0 view shell tftp 1.1.1.1 put

a.cfg command is executed, when users with the user privilege level of 0 log in to the switch, they

can execute the tftp server-address put source-filename command (such as the tftp 192.168 .1.26 put

syslog.txt command), but cannot execute the command with the get, sget or source keyword, and

cannot specify the destination-filename argument.

• The command specified in the undo command-privilege view command can be incomplete. For

example, after the undo command-privilege view system ftp command is executed, all commands

starting with the keyword ftp (such as ftp server acl, ftp server enable, and ftp timeout) are restored

to their default level. If you have modified the level of commands ftp server enable and ftp timeout,

and you want to restore only the ftp server enable command to its default level, you should use the

undo command-privilege view system ftp server command.

• If y

ou modify the command level of a command in a specified view from the default command level

to a lower level, remember to modify the command levels of the quit command and the

corresponding command that is used to enter this view. For example, the default command level of

commands interface and system-view is 2 (system level). If you want to make the interface

command available to the level 1 users, you need to execute the following three commands:

command-privilege level 1 view shell system-view, command-privilege level 1 view system

interface GigabitEthernet 1/0/1, and command-privilege level 1 view system quit. Then, the level

1 users can enter system view, execute the interface ethernet command, and return to user view.

Examples

# Set the command level of the interface command to 0 in system view.

<Sysname> system-view

[Sysname] command-privilege level 0 view system interface

display clipboard

Syntax

display clipboard [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular

expressions, see the chapter “CLI configuration.”

begin: Displays the first line that matches the specified regular expression and all lines that follow.

exclude: Displays all lines that do not match the specified regular expression.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters.

4

Description

Use the display clipboard command to view the contents of the clipboard.

To copy the specified content to the clipboard:

• Move the cursor to the starting position of the content and press the <Esc+Shift+,> combination.

• Move the cursor to the ending position of the content and press the <Esc+Shift+.> combination.

Examples

# View the content of the clipboard.

<Sysname> display clipboard

---------------- CLIPBOARD-----------------

display current-configuration

display command-alias

Syntax

display command-alias [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular

expressions, see the chapter “CLI configuration.”

begin: Displays the first line that matches the specified regular expression and all lines that follow.

exclude: Displays all lines that do not match the specified regular expression.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters.

Description

Use the display command-alias command to display defined command aliases and the corresponding

commands.

Examples

# Display the defined command aliases and the corresponding commands.

<Sysname> display command-alias

Command alias is enabled

index alias command key

1 show display

display history-command

Syntax

display history-command

5

View

Any view

Default level

1: Monitor level

Parameters

None

Description

Use the display history-command command to display commands saved in the history command buffer.

By default, the system saves the last 10 executed commands in the history command buffer. To set the size

of the history command buffer, use the history-command max-size command. For more information, see

the chapter “Logging in to the switch commands.”

Examples

# Display history commands in current user view.

<Sysname> display history-command

display history-command

system-view

vlan 2

quit

display hotkey

Syntax

display hotkey

View

Any view

Default level

1: Monitor level

Parameters

None

Description

Use the display hotkey command to display hotkey information.

Examples

# Display hotkey information.

<Sysname> display hotkey

----------------- HOTKEY -----------------

=Defined hotkeys=

Hotkeys Command

CTRL_G display current-configuration

CTRL_L display ip routing-table

CTRL_O undo debug all

6

=Undefined hotkeys=

Hotkeys Command

CTRL_T NULL

CTRL_U NULL

=System hotkeys=

Hotkeys Function

CTRL_A Move the cursor to the beginning of the current line.

CTRL_B Move the cursor one character left.

CTRL_C Stop current command function.

CTRL_D Erase current character.

CTRL_E Move the cursor to the end of the current line.

CTRL_F Move the cursor one character right.

CTRL_H Erase the character left of the cursor.

CTRL_K Kill outgoing connection.

CTRL_N Display the next command from the history buffer.

CTRL_P Display the previous command from the history buffer.

CTRL_R Redisplay the current line.

CTRL_V Paste text from the clipboard.

CTRL_W Delete the word left of the cursor.

CTRL_X Delete all characters up to the cursor.

CTRL_Y Delete all characters after the cursor.

CTRL_Z Return to the User View.

CTRL_] Kill incoming connection or redirect connection.

ESC_B Move the cursor one word back.

ESC_D Delete remainder of word.

ESC_F Move the cursor forward one word.

ESC_N Move the cursor down a line.

ESC_P Move the cursor up a line.

ESC_< Specify the beginning of clipboard.

ESC_> Specify the end of clipboard.

hotkey

Syntax

hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U } command

undo hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U }

View

System view

Default level

2: System level

Parameters

CTRL_G: Associates hot key Ctrl+G to the specified command.

CTRL_L: Associates hot key Ctrl+L to the specified command.

CTRL_O: Associates hot key Ctrl+O to the specified command.

7

CTRL_T: Associates hot key Ctrl+T to the specified command.

CTRL_U: Associates hot key Ctrl+U to the specified command.

command: The command line associated with the hot key.

Description

Use the hotkey command to associate a hot key to a command.

Use the undo hotkey command to restore the default.

By default, Ctrl+G, Ctrl+L and Ctrl+O have these corresponding commands:

• Ctrl+G corresponds to display current-configuration.

• Ctrl+L corresponds to display ip routing-table.

• Ctrl+O corresponds to undo debugging all.

You can modify the associations as needed.

Examples

# Associate the hot key Ctrl+T to the display tcp status command.

<Sysname> system-view

[Sysname] hotkey ctrl_t display tcp status

# Display hotkeys.

[Sysname] display hotkey

----------------- HOTKEY -----------------

=Defined hotkeys=

Hotkeys Command

CTRL_G display current-configuration

CTRL_L display ip routing-table

CTRL_O undo debug all

CTRL_T display tcp status

=Undefined hotkeys=

Hotkeys Command

CTRL_U NULL

=System hotkeys=

Hotkeys Function

CTRL_A Move the cursor to the beginning of the current line.

CTRL_B Move the cursor one character left.

CTRL_C Stop current command function.

CTRL_D Erase current character.

CTRL_E Move the cursor to the end of the current line.

CTRL_F Move the cursor one character right.

CTRL_H Erase the character left of the cursor.

CTRL_K Kill outgoing connection.

CTRL_N Display the next command from the history buffer.

CTRL_P Display the previous command from the history buffer.

CTRL_R Redisplay the current line.

CTRL_V Paste text from the clipboard.

CTRL_W Delete the word left of the cursor.

8

CTRL_X Delete all characters up to the cursor.

CTRL_Y Delete all characters after the cursor.

CTRL_Z Return to the user view.

CTRL_] Kill incoming connection or redirect connection.

ESC_B Move the cursor one word back.

ESC_D Delete remainder of word.

ESC_F Move the cursor forward one word.

ESC_N Move the cursor down a line.

ESC_P Move the cursor up a line.

ESC_< Specify the beginning of clipboard.

ESC_> Specify the end of clipboard.

quit

Syntax

quit

View

Any view

Default level

0: Visit level (in user view)

2: System level (in other views)

Parameters

None

Description

Use the quit command to return to a lower-level view.

In user view, the quit command terminates the connection and reconnects to the switch.

Examples

# Switch from GigabitEthernet 1/0/18 interface view to system view, and then to user view.

[Sysname-GigabitEthernet1/0/18] quit

[Sysname] quit

return

Syntax

return

View

Any view except user view

Default level

2: System level

Parameters

None

9

Description

Use the return command to return to user view, which can also be done with the hot key Ctrl+Z.

Related commands: quit.

Examples

# Return to user view from GigabitEthernet 1/0/18 view.

[Sysname-GigabitEthernet1/0/18] return

screen-length disable

Syntax

screen-length disable

undo screen-length disable

View

User view

Default level

1: Monitor level

Parameters

None

Description

Use the screen-length disable command to disable the multiple-screen output function.

Use the undo screen-length disable command to enable the multiple-screen output function.

By default, a login user uses the settings of the screen-length command. The default settings of the

screen-length command are: multiple-screen output is enabled and 24 lines are displayed on the next

screen. For more information about the screen-length command, see the chapter “Logging in to the

switch commands.”

When the user logs out, the settings restore to their default values.

Examples

# Disable multiple-screen output for the current user.

<Sysname> screen-length disable

super

Syntax

super [ level ]

View

User view

Default level

0: Visit level

10

Parameters

level: User level, which ranges from 0 to 3 and defaults to 3.

Description

Use the super command to switch from the user privilege level to a specified user privilege level.

If a level is not specified, the command switches the user privilege level to 3. Command levels include four

privileges: visit (0), monitor (1), system (2), and manage (3). You can assign a privilege level according

to the user’s need. When logging in to the switch, the user can access the assigned level and all levels

below it.

A user can switch to a lower privilege level unconditionally. A logged-in AUX or VTY user must input the

switching password set by using the super password command to switch to a higher privilege level. If the

password is incorrect or no password is configured, the switching operation fails.

Related commands: super password.

Examples

# Switch to user privilege level 2 from privilege level 3.

<Sysname> super 2

User privilege level is 2, and only those commands can be used

whose level is equal or less than this.

Privilege note: 0-VISIT, 1-MONITOR, 2-SYSTEM, 3-MANAGE

# Switch the user privilege level back to 3 (the switching password 123 has been set). If no password is

set, the user privilege level cannot be switched to 3.

<Sysname> super 3

Password:

User privilege level is 3, and only those commands can be used

whose level is equal or less than this.

Privilege note: 0-VISIT, 1-MONITOR, 2-SYSTEM, 3-MANAGE

super authentication-mode

Syntax

super authentication-mode { local | scheme } *

undo super authentication-mode

View

System view

Default level

2: System level

Parameters

local: Authenticates a user by using the local password set with the super password command. When no

password is set by using the super password command, two results can occur: The privilege level switch

succeeds if the user is logged in through the console port. The switch fails if the user logs in through any

of the VTY user interfaces or inputs an incorrect switch password.

scheme: AAA authentication. For more information about AAA, see the Security Configuration Guide.

local scheme: First local and then scheme, which authenticates a user by using the local password first.

If no password is set for the user logged in through the console port, the privilege level switch succeeds.

Page is loading ...

H3C S5120-EI Series Command Reference Manual

Related papers

Other documents