PK-210
Proximity Keypad
User Manual & Operating Guide
www.accesscontrolequipment.co.uk
1
2
3
4
5
6
7
8
9
0
#
*
www.accesscontrolequipment.co.uk
ace
Main technical parameters:
Ÿ Working voltage:
DC12-24V
Ÿ Open key current:
<1000mA
Ÿ Quiescent current:
<60mA
Ÿ Memory capacity:
250 users
Ÿ Induction distance:
3~8 cm
Ÿ Card types:
EM
Ÿ Working temperatures:
-10°C ~ 60°C
Ÿ Working Humidity:
10% ~ 90%
Ÿ Dimensions:
128 x 82 x 28mm
Front View
1
2 3
4
5 6
7
8 9
*
0 #
LED lights
Keys
Rear View
Screws
K2
SW1
RESET
Speaker
Wiring block
Tamper switch
Reset Button
120000401 12,9458 000
Example of proximity card
Example of security screwdriver
TECHNICAL DATA AND DIMENSIONS
www.accesscontrolequipment.co.uk
Common power supply connection
Common 12v3A
NC
COM
NO
GND
12V
VSS
OPEN
PK - 210
GND
+12V
+V
- V
+V
- V
Power off = lock open
Power on = lock open
Common power supply connection
Special Power Supply
NC
COM
NO
GND
12V
VSS
OPEN
PK - 210
+V
- V
Power on = lock open
+V
- V
Power off = lock open
Open door button
Open door button
Wiring Diagram
www.accesscontrolequipment.co.uk
GB
2003/108/CE Directive
for waste electrical and
electronic Equipments
DISPOSE OF PROPERLY
ENVIRONMENT - NOXIOUS MATERIALS
EUROPEAN MARK CERTIFYING CONFORMITY
TO THE ESSENTIAL REQUIREMENTS OF THE
STANDARDS 98/37/EC
Made using
recycled
paper
The manufacturer reserves the right to make amendments to this manual without prior
notice and declines all responsibility for any errors, personal injury or damage to
property.
L.E.D
Light codes and their meaning:
Ÿ Default ready state = Red Notes
Ÿ Programming mode = Yellow/Red Ÿ Programming mode will exit automatically after 12 seconds without
Ÿ Accepted program command = Yellow/Green input
Ÿ Awaiting info prog mode = Yellow Ÿ If you need to cancel something mid-programming don't panic just
Ÿ Accepted user code = Green press the “#” key and this will exit programming mode
To enter programming mode:
Ÿ Press the “#” key
Ÿ Enter “12345" or (code you have programmed using “step 6")
Ÿ You can now enter into one of the below steps of programming
To enter a new 6 digit code (to let users open barrier):
Ÿ Enter prog mode (follow step1)
Ÿ Yellow/Red LED illuminated
Ÿ Now press the number “2" key
Ÿ Yellow LED only illuminated
Ÿ Enter 4 digit User Slot Number i.e. “0001" (this can go up to “2000")
Ÿ Yellow/Green LED illuminated
Ÿ Enter a 6 digit code e.g. “112233" OR present a card to the centre of
the keypad
Ÿ You will hear a beep this confirms correct registration
Ÿ LED will return to Yellow/Red
Ÿ Now exit the program by pressing the “#” or “6" key
Ÿ
To remove the codes/cards:
Ÿ Enter prog mode (follow step1)
Ÿ Yellow/Red LED illuminated
Ÿ Now press the number “4" key
Ÿ Yellow LED only illuminated
Ÿ You will hear a beep after 3 seconds
Ÿ LED will return to Yellow/Red
Ÿ Now exit the program by pressing the “#” or “6" key
Ÿ
To change “pulse” open signal time
Ÿ Enter prog mode (follow step1)
Ÿ Yellow/Red LED illuminated
Ÿ Now press the number “5" key
Ÿ Yellow LED only illuminated
Ÿ Enter pulse time minimum “01" 1 second or max “99" 99 seconds
most products only require 1 second
Ÿ For 1 second enter “0" then “1" keys
Ÿ Yellow/Green LED illuminated
Ÿ You will hear a beep
Ÿ LED will return to Yellow/Red
Ÿ Now exit the program by pressing the “#” or “6" key
To change system password:
Ÿ Enter prog mode (follow step1)
Ÿ Yellow/Red LED illuminated
Ÿ Now press the number “1" key
Ÿ Yellow LED only illuminated
Ÿ Enter new 5 digit code e.g. “98765"
Ÿ Yellow/Green LED illuminated
Ÿ You will hear a beep
Ÿ LED will return to Yellow/Red
Ÿ Now exit the program by pressing the “#” or “6" key
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
To remove individual codes/cards:
Ÿ Enter prog mode (follow step1)
Ÿ Yellow/Red LED illuminated
Ÿ Now press the number “3" key
Ÿ Yellow LED only illuminated
Ÿ Enter the User ID to delete or present card
Ÿ LED will Flash GREEN (this is confirmation card/code has been
erased)
Ÿ LED will return to Yellow/Red
Ÿ Now exit the program by pressing the “#” or “6" key
ALL!!
Programming Instructions
/
