Sanyo VHR-154G User manual

Brand: Sanyo

Model: VHR-154G

Type: User manual

This manual is also suitable for

Sq#4/m

Service Manual Video Cassette

Recorder

VHR-I 50 series

VHR-153G

VHR-154G

VHR-141

VHR-171, SP

VHR-150G

Fii51Iw

PAL

Table of Contents

1. CIRCUIT BOARD LOCATIONS

1-1. MAINBOARDS ..................................................................... 1

1-2. LOCATION FOR TAPE PATH ADJUSTMENT ................................... 1

2. ELECTRICAL ADJUSTMENT

2-1. Preparation ..................................................................... 2

2-2. SERVO CIRCUIT ADJUSTMENT ................................................. 4

2-3. VIDEO CIRCUIT ADJUSTMENT .............................................*....

2-4. Videotext DECODER CIRCUIT ADJUSTMENT .............................. 8

2-5. AUDIOCIRCUIT ADJUSTMENT .................................................. 9

2-6. TUNER lFCIRCUIT ADJUSTMENT ............................................... 9.

s, DISASSEMBLY PROCEDURES

3-1. REMOVAL OF REMOTE CONTROL UNITCASE ............................. 10

SP4, SP4V series

REFERENCE No. WM530862

3103L11(N)

1. CIRCUIT BOARD LOCATIONS

1-1.

MAIN BOARDS

TM-2

L13L040

CP-1(Video, Servo & Audio) board

w-l

(PowerSUPPW)hard ~

TB-1 (Terminal) board

~(Control)

oard

TM-1

Tunin

det.) board

CP-2 (Servo & Syscon) board

‘TM-8 (VPS)board

‘h.._.-T6-6 (Video text decoder) board

Installed specific equipment and models

TM-5 (OSA on

screenassist)board:VHR-150G, 150E, 150EX, 150EE, 1501,1501R,150HD, 150SA, 150PS, 150, 141,171and 17SP.

VD-1 (MESECAMdet.)board:VHR-150G, 150EX, 150EE, 150PS, 153G and 154G.

TM-8 (VPS)board:VHR-150G, 153G and 154G.

TM-6 (Videotextdecoder)board:VHR-153G and 154G.

!!g

1-2. LOCATION FOR TAPE PATH ADJUSTMENT

NOTE: Test DointTP182 and TP183 for tape path adjustment is shown in figure below.

For adjustment, refer to the separate volume-’’Mechanism Service Technical Information”.

POSLO12

Shieldcase

\ 11

/\-\

TPI83

TPI82 CN181

SW-P.

Erw.

Fig. 1-2 Pre-amp Unit

...?,.:,

,.. :,,’.

—l—

3103J11(N)

2. ELECTRICAL ADJUSTMENT

“L

2-1. PREPARATION

2-1-1. EQUIPMENT

●

Colour TV monitor

PAL Colour-bar generator (with RF and LINE OUTPUT)

Audio signal generator

Oscilloscope (dual trace; frequency response: 10MHZ or

more; probe: 10:1 )

Frequency counter (countable to 10MHZ or higher)

Digital voltmeter

AC voltmeter

In/output probes

Alignment cassette (VHJ-0008) PAL Colour bar 1KHz

Alignment cassette (VHJ-0009) Monoscope 6KHz

Alignment cassette (VHJ-0051 ) Check for D.O.C.

Alignment cassette (VHJ-0023) PAL Monoscope 6KHz,

PAL Colour-bar 1KHz, SECAM Colour-bar 1KHz, PAL RF

Sweep MESECAM Colour-bar 1KHz, NTSC Colour-bar

1KHz.

Relay jig (VHJ-0066) 7-wire cable for Pre-amp unit

Relay jig (VHJ-0084) for CP-1 and CP-2 board

Relay jig (VHJ-0085) for Video pre-amp unit

2-1-2. CONNECTING THE RELAY JIG

When repairing CP-1 and CP-2 board

(seeFigs.2-1-2 and 2-1-3)

NOTE: The connection of any Relay jigs can be done

without removing the front panel of the main unit.

1. Remove the seven screws of the CP- 1 board to take out

with CP-2 board connected.

2. Insert the CP-1 board with CP-2 board connected in the

slit of chassis as shown in Fig. 2-1-3 (right).

3. Connect CNOI and CN02 of Relay jig (VHJ-0084) into

connectors of the PW-I board and the Pre-amp unit, in the

direction of arrow as shown in Fig. 2-1-3 (left). Fix the

relay jig with screw if necessary.

4. Connect 12-pin, 8-pin and 4-pin connectors of the Relay

jig to connectors CN541, CNI 01 and CN201 on the CP-I

board, respectively.

5. Connect connector (1) from ACE head to CN06 of the

Relay jig (VHJ-0084).

6. After finishing the repairs and adjustments, put the Flat

cables back to its former position.

When repairingthe Pre-amp unit

(seeFigs.2-1-1 and 2-1 -4)

1. Remove the Pre-amp unit from the chassis, connect

Relay jig (VHJ-0066) between the Pre-amp unit and

drum assembly.

2. Connect Relay jig (VHJ-0084) excepting 8-pin connector

between the PW- 1 board and CP- 1 board as shown in

Fig. 2-1-4. Fix the relay jig with screw if necessary.

3. Connect Relay jig (VHJ-0085) between the top of Pre-

amp unit and CNIOI on the CP-I board.

NOTE: When repairing or adjusting the Pre-amp unit,

temporary fasten or securely touch one end of the

shield case to the metal chassis.

Kwco9

CN02 connectorto

CN181 of Pre-ampunit

8-pin connectorto

CN101 ofCP-1board

Relay jig VHJ-0085

Fig. 2-1-1

l“w-!-

CN06 connectorfrom

connector(1)

Ak:::y;:yzrd

8-pin mnnectorto

‘CN101 of CP-1 board

c .-

CN511 of PW-1 board

\S 4-oin ccmnectorto

Relay jig VHJ-0084

CN201 of CP-1 board

Fig. 2-1-2

—2—

3103J21IN)

P1OJO11

Relayjig (VHJ-0064)=

I--CNO6 forconnector(1)fromACE

head

iwl

Pre-amp unit

8-pm connector toCN101

4-pm connector to CN201

Flat cable (24-wire cable)

ACEhead

Fig. 2-1-3

Relay

Leadwires of connector(1)

Remove8-pin connector

Pre-ampunit

ofjig(VHJ-0084)

jig(VHJ-0066)

Flatcable

-u

Yr’((11

Fig. 2-1-4

POSJO12

2-1-3. SET-UP

Because the RF input signal is used for circuit adjustments,

. Check to be sure that there is no spike noise in the sync

connect the colour-bar generator to the ANT IN terminal of

part of the horizontal sync signal.

the VCR. The RF input signal is processed by the tuner and

lFcircuit. It is improtant that thevideooutput signal of the IF

W05J031

circuit satisfies the items shown in Fig. 2-1-5. Connect the

oscilloscope to the VIDEO OUTPUT terminal of the video

circuit and terminate with a 75f) load, and then check the

video output signal.

The amplitude of the sync signal should be approxi-

mately 0.3 Vp-p.

The amplitude of the video signal should be approxi-

mately 0.7 Vp-p.

While observing the oscilloscope or TV screen, make

Hsyncsignal

fine-tuning adjustments so that the colour burst

Fig. 2-1-5

amplitudeis approximately0.3 Vp-p.

—3—

3103S1 1(N)

2-2. SERVO CIRCUIT ADJUSTMENT ..... CP-1 board and Video pre-amp unit

NOTE (1) : These adjustments should be carried out upon completion of the transport adjustments.

(2) : If the tape transport adjustments are carried out after these adjustments, follow the procedures again in SWITCHING

POSITIONS.

—

10.

—

Item

SWITCHING

POSITION

SLOW

TRACKING

for

SP MODE

Input

Alignment

cassette

(VHJ-0009

VHJ&23)

Colour bar

from

Colour bar

generator

Mode

PLAY

(SP mode)

REC

PIAY

SLOW

(SP mode)

Point

VIDEO

OUTPUT

TP101

RF SW

pulse

TP183

(Video pre-

amp unit)

TP183

RF SW

Pulse

J3042

CTL

Pulse

Location

VR351

VR353

Remark

W25S031

Videosignal

7654321 —

V sync

Press the tracking control (+) (-) buttons

simultaneously to the center position

(on the display ‘T –:– “).

Adjust VR351 so that the phase of the

leading edge of the vertical sync signal

is delayed 6.5 y 0.5 H from the rise of

the RF switching pulse waveform.

W20SOOS

CTLpulse

~12*1 msec

RF switching

pulse

1. Playback the recorded part, and VCR in

the SLOW (SP) mode by remote control

unit.

2. Press the tracking control (+)(-) buttons

simultaneously to the center position

(on the display ‘T –:– “).

3. Adjust VR353 so that there is a trigger

of the peak level of the positive pulse

reading edge of the CTL pulse and the

time from this point to the leading edge

of the RF switching pulse is 12 t 1

msec.

4. Confirm that the noise at the “+” and “-”

terminals for tracking adjustment is

same at the upper and lower edges of

the screen. If not, readjust VR353.

Shieldcase

F o m 0[ @-@}_!

TP183 TP182 CN181

SW-P.

ENV.

Fig. 2-2-1 Video pre-amp unit

—4—

3103S21(N)

k).

Item Input Mode Point Location Remark

W20S01o

CTL pulse

~19 = 1 msec

RF switching

pulse

1. Playback the recorded part, and

VCR in

REC

TP183

the SLOW (LP) mode by remote control

SLOW

Colour bar

RF SW

unit.

z TRACKING

from PLAY

Pulse

2. Press the tracking control (+)(-) buttons

for Colour bar

VR354 simultaneously to the center position

LP MODE generator SLOW

J3042

(on the display “T –:– “).

(LP mode)

CTL

3. Adjust VR354 so that there is a trigger

Pulse

of the peak level of the positive pulse

reading edge of the CTL pulse and the

time from this point to the leading edge

of the RF switching pulse is 19 & 1

msec.

4. Confirm that the noise at the “+” and “-”

terminals for tracking adjustment is

same at the upper and lower edges of

the screen. If not, readjust VR354.

P13S034

TP201(HOT)

TP103[6”:

TP?02

!,?-;

119

;Ic :

TP101

; 101!

VIDEO+@ [:?

(-0:

.-.

~o:

:6::. --; #

OUT

1@CN

VR;O1

.@-’

I 1:[861

81AS

VR102

VR101

I 10,

.--- ————-- -!

I:J

P8-Y ‘- ~ti-%-O-S~- ~

I rl

VD-1

r, MESECAM

~--_7

I L?

101’

--------

I__. -____:

Idet.

;–--;1

I 1:!

[-;

CN331

IC201

IoICN

Q1102:?

I @

1851

‘1:1

I ~,

;;

I ~1

~_-__-a

II VIF ~ ,----1

IC301

I:-@;

I IC1ll’:

“

unit I I

L------

,Tunerl I , , ~

, j

VR351

‘7

t----

TN-7~~ [ [j

I IRF ;

:-J SW-PO.

TM-8 VPS

I ‘ conv.1

~-—----,

Sync.\l ~ II I I ,

---------

1--.,

,--- .--:0)

det. ‘1 I

‘1 I

: o~o,ti-

IL___

-. .

L---J

L-–-j

o K::;;5;:I:J0 “-:-– ----_:::~o

~J3042

0 ‘- -CW301

VR353

VR354

SPSLW

LPSLW

Fig. 2-2-2 CP-1 board (Foil side view)

—5—

‘-

.-/

31OOV1 1(N)

2-3. VIDEO CIRCUIT ADJUSTMENT ... CP-1 board and Video pre-amp unit

NOTE (1) : Use the Relay jig mentiond in the 2-1. PREPARATION to provide easy adjustment of the Pre-amp unit.

(2) : When adjustment No. 1, No. 2 and No. 5 below, terminate VIDEO OUTPUT TP101 at 75 ohms.

(3) : ‘No-signal REC mode’ is not to supply any signal to VIDEO INPUT terminal.

—6–

do. Item Input Mode

Point Location

Remark

WI5vfxi6

TPI 81 (HOT)

34* 2 mVp-p

Colour bar

C REC

from

shield case

CURRENT Colour bar

REC

(GND)

VR181

(Video pre-

generator

1. Rotate VR182 so that the luminance

amp unit)

level is minimize.

2. AdjustVR181 so that the level is 34 * 2

mVp-p.

W20VO07

130

* 5 mVp-p

,.,.

TP181 (HOT)

Y REC

shield case

CURRENT

No-signal

REC

(GND)

VR182

(Video pre-

1. Set the channel selector buttons to AV

amp unit)

position and put the VCR in the no-

signal REC mode.

2. AdjustVR182 so that the level is 130 &

5 mVp-p.

3. Follows are the applicable models and

their corresponding mark.

P60V012

Shield case

VR181

VR182

REC-C

REC-Y

TP181

CN181

Fig. 2-3-1 Video pre-amp unit

,.,

—7—

31WX12(N)

2-4. VIDEO TEXT DECODER CIRCUIT ADJUSTMENT ... TM-6 and CP-1 board

—

Item

DECODER

Vxo

Input

NONE

Mode

E-E

Point

Emiter of

Q1 102

(CP-1 board)

Fig. 2-2-2

see page 5

Location

c 761

Remark

Set the vartical scale (VOLTAGE/DIV.)

of the oscilloscope to 10 mV/DIV..

Connect the frequency counter to

Emitter of QI 102 and ground through a

pre-amp of the above oscilloscope.

Press the “MENU” button on the

remote control unit.

Adjust CT761 so that the frequency is

4433619 t 20 Hz.

POSXO03

764

[

IC761

[

IC769

TP762 (GND)

Fig. 2-4-1 TM-6 board (Partssideview)

—8—

31CDA11(N)

2-5. AUDIO CIRCUIT ADJUSTMENT ... CP-1 board

do. Item

Input

Mode

Point

Location

BIAS

No-signal

REC

TP201 (HOT)

LEVEL

TP202

VR201

1 I

1 1

Remark

1. Set the channel selector buttons to the

AV position and put the VCR in the no-

signal REC mode.

2. Adjust VR201 so that the level is 23

mVrms.

2-6. TUNER IF CIRCUIT ADJUSTMENT ... VIF unit

NOTE: There are two of the VIF unit’s type and different with the model (shown in figure below).

—

Item

Input Mode

Point Location

RF AGC

broadcast

E-E

TV screen

VR611

Remark

1, TurnVR611 in the direction which causes

snow to appear, then in the opposite

direction until the snow just disappears.

TYPE A

board

yyc-Q

611

CP-1 board

p- . ..../.r/. </. z...t . . . . . ...<

TYPE B

Fig. 2-6-1 VIF unit (Partsside view)

——

-1

—9—

31OOB11(1)

3. DISASSEMBLY PROCEDURES

- 3-1. REMOVAL OF REMOTE CONTROL UNIT CASE

Open the remote control unit case as follows. Although a

large type remote control unit is shown in the figure bellow,

small type remote control unit can be opened by the same

procedures,

NOTE: When opening the remote control unit for repairing,

use a GUITER PICK made of plastic (1 mm thickness) shown

in the Fig. 3-1-2 or the like (a thin plastic piece) to prevent

scratching.

* Never use a metal screwdriverto avoid scrathing.

1. Open the battery cover and take out batteries, the then

remove the bottom case fixing screw.

2. Applying force strongly to the battery compartment edge

in the arrow (A) direction by your thumb as shown in Fig.

3-1-1 to make a space (B) between the bottom and upper

case as shown in the cross section Fig. 3-1-3.

To make this procedure easier, push the remote control

unit end (C) against your body.

m7aool

Edge

a space (B)

tment

Bottom

Fig. 3-1-1

Po7aoo3

GUITER PICK

Fig. 3-1-4

—lo—

3. Insertthe GUITER PICKabove mentionedintothe space

(B) as shown in Figs. 3-1-3, 3-1-4 and move the PICK in

the arrow (D) and (E) direction, then disconnect two hooks

(F)

of the top of the cases.

4. Applying force to the space (B) and battery compartment

edge by your thumb so that the bottom case is separated

from the upper case as shown in the Fig. 3-1-5.

5. Insert the PICK into the space (G) of the case side slanting-

ly by against the bottom case and move the PICK to

disconnect the hooks (H) of the side in order from top to

bottom.

6. Disconnect the hooks of the other side using the pick by

the same procedure as step 4.

Po7aooz

a’

GUITERPICKor

Thinplasticpiece

Fig. .3-1-2

Make a space(B)

r*”

r#~ER

“ y<j

Hooks

(F)

Bottom case

Uppar case

Fig. 3-1-3

m7aoo4

Keep a space (B)

(H)

Fig.

3-1-5

SqfjNmio

‘..-/

SANYO Electric Co., Ltd.

OSAKA, JAPAN

Apr./’96400OO HA

Printed in Japan

Sanyo VHR-154G User manual

Brand: Sanyo

Model: VHR-154G

Type: User manual

This manual is also suitable for

Download PDF

report

Sanyo VHR-154G User manual

This manual is also suitable for

Sanyo VHR-154G User manual

Related papers

Other documents