MyBinding KF 150PS KF 150CST Operating instructions

MyBinding
Brand
MyBinding
Model
KF 150PS KF 150CST
Type
Operating instructions

MyBinding KF 150PS KF 150CST

These portable and lightweight sealers are perfect for use anywhere. The KF 150PS model makes strong seals on poly bags and other thermoplastic materials, while the KF 150CST model is ideal for sealing cellophane, coated aluminum foil, Kraft paper, and other thicker materials. Both models are easy to operate – simply place the bag between the sealing bars, press down, and release.

The KF 150PS has a 2mm seal width and a 6” sealing length. It features a warm-up time of approximately 5 minutes and two heat settings – low and high. The KF 150CST also has a 6” sealing length, but it has a serrated jaw and a Teflon coating. It also has 8 different temperature settings, allowing you to choose the perfect setting for your material.

MyBinding KF 150PS KF 150CST

These portable and lightweight sealers are perfect for use anywhere. The KF 150PS model makes strong seals on poly bags and other thermoplastic materials, while the KF 150CST model is ideal for sealing cellophane, coated aluminum foil, Kraft paper, and other thicker materials. Both models are easy to operate – simply place the bag between the sealing bars, press down, and release.

The KF 150PS has a 2mm seal width and a 6” sealing length. It features a warm-up time of approximately 5 minutes and two heat settings – low and high. The KF 150CST also has a 6” sealing length, but it has a serrated jaw and a Teflon coating. It also has 8 different temperature settings, allowing you to choose the perfect setting for your material.

SealerSales KF-150PS
Portable 6" Direct Heat Sealer
with 2mm Seal Width
Instruction Manual
LIGHTWEIGHT AND VERSATILE sealer that can be
used anywhere
Model KF-150PS makes a perfect 6” long, strong seal on poly
bags and other thermoplastic materials.
Model KF-150CST is a 6” Teflon-coated direct heat sealer
with a serrated jaw. Ideal for sealing cellophane, coated
aluminum foil, Kraft paper, and other thicker materials.
Portable Sealers KF-150PS, KF-150CST, KF-150CSTA
OPERATION INSTRUCTIONS for
easy to operate
directions for operation
Step 1. Insert power plug into socket.
Step II. Allow the sealer to heat up approximately 5 minutes (warm-up
time will vary with the thickness of the bag to be sealed). Choose either
the low setting for a light material or a the high setting for thicker
materials. The KF-150CSTA has 8 different temperature settings. We
recommend starting at the lowest setting and gradually moving up
as needed.
Step III. After a suitable temperature has been reached, put the bag
edge between the heated sealing bars and press down for 3 seconds. If
the seal weld holds, continue this way.
*If the welding appears to damage the bag, apply pressure on the sealing bar
for less than 3 seconds. If the welding appears incomplete, apply pressure for
more than 3 seconds.
Simply place bag between the sealing bars, press down, and release.
notes
• Never touch the heated bars of the unit
• Never allow a liquid to come in contact with the
unit
• Never shock or drop the unit
• Always have the heating element covered with
Teflon protection for the KF-150PS model
• Keep the heating element and silicone of the KF-
150PS clean
• Always unplug the unit when not n use.
• Always allow the unit to cool down before
putting away
KF-150CST
KF-150PS
No. Description No. Description
1 AC Cord 13 Upper Cover
2 Power Switch 14 Washer
Temperature Controller 15 Silicone Rubber
3 Protected Spring 16 Clamp
4 Down Cover 17 Support Hook
5 Reverted Spring 18 Iron Chain
6 Fixed Screw 19 S Connector
7 Side Fixed Plate 20 Foot Pedal
8 Top/Bottom Sealing Jaw 21 *Rubber Foot (not shown)
9 Heating Element 24 Pin for Teflon Cloth
10 Heat Element Fixed Plate 25 Teflon Cloth
11 Insulated Washer 26 Silicone Rubber Holder
12 Fixed Bolt *Clamp & Pedal Set #16-21
parts list
  • Page 1 1
  • Page 2 2

MyBinding KF 150PS KF 150CST Operating instructions

MyBinding
Brand
MyBinding
Model
KF 150PS KF 150CST
Type
Operating instructions

MyBinding KF 150PS KF 150CST

These portable and lightweight sealers are perfect for use anywhere. The KF 150PS model makes strong seals on poly bags and other thermoplastic materials, while the KF 150CST model is ideal for sealing cellophane, coated aluminum foil, Kraft paper, and other thicker materials. Both models are easy to operate – simply place the bag between the sealing bars, press down, and release.

The KF 150PS has a 2mm seal width and a 6” sealing length. It features a warm-up time of approximately 5 minutes and two heat settings – low and high. The KF 150CST also has a 6” sealing length, but it has a serrated jaw and a Teflon coating. It also has 8 different temperature settings, allowing you to choose the perfect setting for your material.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents