JVC HV-36P38SUE, HV-32P37SUE, HV-28P37SUE User manual

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / All Cover

Cover01

COLOUR TELEVISION

INSTRUCTIONS

FARBFERNSEHGERÄT

BEDIENUNGSANLEITUNG

TELEVISEUR COULEUR

MANUEL D’INSTRUCTIONS

KLEURENTELEVISIE

GEBRUIKSAANWIJZING

TELEVISOR A COLOR

MANUAL DE INSTRUCCIONES

TELEVISORE A COLORI

ISTRUZIONI

TELEVISOR A CORES

INSTRUÇÕES

HV-36P38SUE

HV-32P37SUE

HV-28P37SUE

ENGLISH

DEUTSCH

FRANÇAIS

NEDERLANDS

CASTELLANO

ITALIANO

PORTUGUÊS

LCT1537-001A-U_Cover.fm Page 1 Thursday, September 25, 2003 10:00 AM

1

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Thank you for buying this JVC colour television.

To make sure you understand how to use your new TV, please read this manual thoroughly before you

begin.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

Avoid improper installation and never position the unit

where good ventilation is unattainable.

When installing this television, distance recommendations

must be maintained between the floor and wall, as well as

installation in a tightly enclosed area or piece of furniture.

Adhere to the minimum distance guidelines shown for safe

operation.

Failure to heed the following precautions may result in damage to the TV or

remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be

able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

CAUTION:

• Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

• Avoid damaging the AC plug and power cord.

• When you are not using this unit for a long

period of time, it is recommended that you

disconnect the power cord from the main

outlet.

• The main power button on the TV does not

fully isolate the TV from the AC supply. If you

are not going to use this TV for a long period

of time, be sure to disconnect the AC plug from

the AC socket.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.

Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.

Never use any cleaner or detergent on it.

In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it

yourself or remove the rear cover.

D.I.S.T. demonstration

To start the D.I.S.T. demonstration:

Press the H button to display the menu bar. Then press the yellow button.

A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.

To quit the D.I.S.T. demonstration:

Press the yellow button, b button, p p buttons or any of the number buttons.

HV-36P38SUE_Eng.book Page 1 Friday, September 26, 2003 11:10 AM

2

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

CONTENTS

Setting up your TV ...................................3

Connecting the aerial and VCR ................. 3

Connecting and placing the woofer unit

(HV-36P38SUE only) ............................. 5

Connecting the power cord to the AC

outlet....................................................... 6

Putting the batteries into the Remote

control..................................................... 6

Initial settings ............................................. 6

T-V LINK FUNCTIONS .............................. 9

TV buttons and functions......................11

Turn the Main power on ........................... 12

Turn the TV on from standby mode ......... 12

Choose a TV channel .............................. 12

Adjust the volume .................................... 12

Remote control buttons and

functions..............................................13

Turn the TV on or off from standby

mode .................................................... 13

Choose a TV channel and watch images

from external devices ........................... 14

Adjust the volume .................................... 15

Information function ................................. 15

ZOOM function......................................... 16

3D CINEMA SOUND function.................. 17

Return to TV channel instantly................. 17

Using the FREEZE function ..................... 17

Using the MULTI-PICTURE function ....... 18

Operating a JVC brand VCR or DVD

player.................................................... 19

Teletext function ....................................20

Basic operation ........................................ 20

Using the List Mode ................................. 20

Hold.......................................................... 21

Sub-page ................................................. 21

Reveal...................................................... 21

Size .......................................................... 21

Index ........................................................ 21

Cancel...................................................... 22

Using the TV’s menu..............................23

Basic operation ........................................ 23

PICTURE menu.......................................24

PICTURE MODE ..................................... 24

CONTRAST ............................................. 24

BRIGHT ................................................... 24

SHARP..................................................... 24

COLOUR.................................................. 24

HUE ......................................................... 24

COLOUR TEMP....................................... 24

FEATURES.............................................. 25

SOUND menu ......................................... 28

STEREO / I • II ......................................... 28

BASS........................................................ 28

TREBLE ................................................... 28

BALANCE ................................................ 28

HEADPHONE VOLUME .......................... 28

3D CINEMA SOUND................................ 28

FEATURES menu................................... 29

SLEEP TIMER ......................................... 29

CHILD LOCK............................................ 29

APPEARANCE......................................... 31

BLUE BACK ............................................. 31

SET UP menu ......................................... 32

AUTO PROGRAM.................................... 32

EDIT/MANUAL ......................................... 32

LANGUAGE ............................................. 36

PICTURE TILT ......................................... 36

DECODER (EXT-2).................................. 36

EXT SETTING.......................................... 37

Additional preparation .......................... 40

Connecting the external devices .............. 40

CH/CC numbers ..................................... 43

Troubleshooting .................................... 45

Specifications ........................................ 48

HV-36P38SUE_Eng.book Page 2 Friday, September 26, 2003 11:10 AM

3

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Setting up your TV

Caution

• Turn off all the equipment including the TV before connecting anything.

Connecting the aerial and VCR

• The connecting cables are not provided.

• For further details, refer to the manuals provided with the devices to be connected.

 If connecting a VCR, follow A

AA

A

→

B

BB

B

→

C

CC

C.

 If not connecting a VCR, follow 1

11

1.

To operate T-V LINK functions, a T-V

LINK compatible VCR must be connected to

the EXT-2 terminal on the TV. For details

about T-V LINK functions, see “T-V LINK

FUNCTIONS” on page 9.

• A video can be viewed from the VCR

without performing C. For details, refer

to your VCR instruction manual.

• To connect additional external devices,

please see “Connecting the external

devices” on page 40.

• To connect additional audio equipments,

see “Connecting Speakers/Amplifier” on

page 42.

• When a decoder is connected to a T-V

LINK compatible VCR, set the

DECODER (EXT-2) function to ON. For

details, see “DECODER (EXT-2)” on

page 36. Otherwise, you will not be able

to view scrambled channels.

EXT-1

EXT-

4

EXT-2

S

EXT-3

S

AUDIO OUT

L

Pr

Pb

R

L

Y

R

75-ohm

Coaxial

Cable

21-pin

SCART

Cable

Back of the TV

75-ohm

Coaxial

Cable

AV IN/OUT

Terminal

To Aerial

Output

To Aerial

Input

VCR

Aerial

EXT-1

EXT-

4

EXT-2

S

EXT-3

S

AUDIO OUT

L

Pr

Pb

R

L

Y

R

75-ohm

Coaxial

Cable

21-pin

SCART

Cable

Back of the TV

75-ohm

Coaxial

Cable

AV IN/OUT

Terminal

To Aerial

Output

To Aerial

Input

Aerial

HV-36P38SUE

HV-32P37SUE/HV-28P37SUE

VCR

HV-36P38SUE_Eng.book Page 3 Friday, September 26, 2003 11:10 AM

4

Setting up your TV

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

 Rear Panel

1 Aerial socket (page 3)

2 Woofer terminal (pages 5)

3 EXT-1 terminal (pages 3, 37, 40)

4 EXT-2 terminal (pages 3, 9, 37, 40)

5 EXT-3 terminal (pages 37, 40)

6 EXT-4 terminal (pages 37, 40)

7 AUDIO OUT terminal (page 42)

1 Aerial socket (page 3)

2 EXT-1 terminal (pages 3, 37, 40)

3 EXT-2 terminal (pages 3, 9, 37, 40)

4 EXT-3 terminal (pages 37, 40)

5 EXT-4 terminal (pages 37, 40)

6 AUDIO OUT terminal (page 42)

EXT-

1

EXT-

4

EXT-

2

S

EXT-

3

S

AUDIO OUT

L

Pr

Pb

R

L

Y

R

HV-36P38SUE

EXT-1

EXT- 4

EXT-2

S

EXT-3

S

AUDIO OUT

L

Pr

Pb

R

L

Y

R

HV-32P37SUE/HV-28P37SUE

HV-36P38SUE_Eng.book Page 4 Friday, September 26, 2003 11:10 AM

Setting up your TV

5

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Connecting and placing the

woofer unit (HV-36P38SUE

only)

Connect the supplied woofer connector to the

woofer terminal on the back of the TV.

If the woofer unit is not connected, you will

not be able to enjoy the bass sound.

• Connect so that the lever is raised.

• When disconnecting the woofer

connector, do so while pushing the lever.

 Placing the woofer unit

As shown in the diagram, affix the

supplied stoppers to the four corners

of the side of the woofer unit that will

be used as the base.

The woofer unit can be used either standing

up or lying down.

There is no difference between the top and

bottom of the woofer unit irrespective of

whether it is being used standing up or lying

down.

Place the woofer unit within the range

of the connection cable.

It is recommended that the woofer unit be

placed with the speaker facing forwards.

Pay attention to the following in order

to prevent unnatural colours from

appearing in the corner of the screen.

• Place the woofer unit at least 20 cm away

from either side of the TV.

• Do not place the woofer unit on top of the

TV.

• When the TV is used on a TV stand or

table, do not place the woofer unit

underneath the TV.

E

X

T

-

1

EXT-

4

E

X

T

-

2

S

E

X

T

-

3

S

A

U

D

IO

O

U

T

L

P

r

Pb

R

L

Y

R

Lever

HV-36P38SUE_Eng.book Page 5 Friday, September 26, 2003 11:10 AM

6

Setting up your TV

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Connecting the power cord to

the AC outlet

Caution

• Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

Putting the batteries into the

Remote control

Use two AA/R6 dry cell batteries.

Insert the batteries from the - end, making

sure the + and - polarities are correct.

• Follow the warnings printed on the

batteries.

• Battery life is about six months to one

year, depending on your frequency of use.

• The batteries we supply are only for

setting up and testing your TV, please

replace them as soon as necessary.

• If the remote control does not work

properly, replace the batteries.

Initial settings

When the TV is first turned on, it enters the

initial setting mode, and the JVC logo is

displayed. Follow the instructions on the on-

screen display to make the initial settings.

1 Press the Main power button on the

TV

The Power lamp lights red (for power on),

then green (for TV on) and the JVC logo

is displayed.

• If the power lamp stays red and does

not change to green:

Your TV is in the standby mode. To

turn the TV on, set the VCR/TV/DVD

switch on the remote control to the TV

position and press the # button. (See

page 13.)

Yellow button

Blue button

7 button

s

Main power

button

Power lamp

HV-36P38SUE

Main power

button

Power lamp

HV-32P37SUE/HV-28P37SUE

HV-36P38SUE_Eng.book Page 6 Friday, September 26, 2003 11:10 AM

Setting up your TV

7

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

• The JVC logo appeares only once

when your TV has been turned on. In

this case, use the “LANGUAGE” and

“AUTO PROGRAM” functions to

make the initial settings. For details,

see “SET UP menu” on page 32.

2 Press the a

aa

a button

The LANGUAGE menu appears.

3 Press the 5

55

5 and 6

66

6 buttons to

choose ENGLISH. Then press the

a

aa

a button

English is set for the on-screen display

description. The COUNTRY menu

appears as a sub-menu of the AUTO

PROGRAM function.

There are two COUNTRY menus.

Pressing the yellow button changes the

COUNTRY menu as follows:

4 Press the 5

55

5 and 6

66

6 buttons to

choose the country where you are

now located

5 Press the blue button to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears

and received TV channels are

automatically registered in the

Programme numbers (PR).

• Perform the “ACI function” operation

(see page 8) when “ACI START/ACI

SKIP” is displayed.

• To cancel the AUTO PROGRAM

function:

Press the b button.

After the TV channels have been

registered in the Programme

numbers (PR), the EDIT menu

appears

• You can proceed to edit the

Programme numbers (PR) using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL” on page 32.

• If you do not need to use the EDIT/

MANUAL function, go to the next

step.

D0002(E)-EN

> LANGUAGE

OK

MORE

START

D0003-EN

OK

MORE

START

OK

> COUNTRY

CH 28

>> AUTO PROGRAM

14%

D0004-EN

OK

> EDIT

PR ID

AV

01

02

03

04

05

06

07

08

09

BBC1

31

32

D0038-EN

OK

DELETE

MANUAL

ID

MOVE

INSERT

CH/CC 31

CH/CC

HV-36P38SUE_Eng.book Page 7 Friday, September 26, 2003 11:10 AM

8

Setting up your TV

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

6 Press the a

aa

a button to display the

T-V LINK menu

If you do not have a T-V LINK

compatible VCR connected:

Press the b button to exit the T-V LINK

menu.

The T-V LINK menu disappears.

If you have a T-V LINK compatible

VCR connected to the EXT-2

terminal:

Follow the operating procedure

“Downloading the data to VCR” on

page 9 to transmit the Programme number

(PR) data.

Now, the initial settings are complete,

and you can watch the TV

• When your TV can detect the TV channel

name from the TV channel broadcast

signal, it automatically registers the TV

channel name (ID) to the Programme

number (PR) in which the TV channel has

been registered.

• If a TV channel you want to view is not

set to a Programme number (PR),

manually set it using the MANUAL

function. For details, see “EDIT/

MANUAL” on page 32.

• The TV channel is not registered in

Programme number PR 0 (AV). When

you want to register a TV channel to PR 0

(AV), manually set it using the

MANUAL function. For details, see

“EDIT/MANUAL” on page 32.

 ACI function

This TV has an ACI function which decodes

the ACI (Automatic Channel Installation)

data.

Using the ACI function allows all TV

channels transmitted from the cable TV

station to be properly registered quickly

according to the data from the cable TV

station.

If “ACI START/ACI SKIP” appears in

the AUTO PROGRAM menu:

You can use the ACI (Automatic Channel

Installation) function to decode the ACI data

and complete the registration of all the TV

channels in a short period of time.

Press the 6

66

6 buttons to choose ACI

START. Then press the a

aa

a button to

start the ACI function

Depending on your cable TV station, there

may be a broadcast selection menu set up by

the cable TV station.

Follow the menu indications and use the

5 and 6 buttons to operate the menu.

After you have made the setting, press the

a button.

• If you have any questions about the items

in the Broadcast Selection menu or how to

operate the menu, please contact your

cable TV station.

• If you don’t want to use the ACI function,

press the 6 buttons to choose ACI

SKIP and then press a.

• When the cable TV broadcast reception is

poor, the ACI function will not work

properly.

• If there is an error in the ACI data itself,

the TV channel cannot be registered

properly. If this happens, turn the ACI

function off (ACI SKIP) and use the

AUTO PROGRAM function.

Alternatively, use the EDIT/MANUAL

function to correct the Programme

number (PR) setting.

D0005-EN

DOWNLOAD TV VCR

T-V LINK

OK

EXIT

HV-36P38SUE_Eng.book Page 8 Friday, September 26, 2003 11:10 AM

Setting up your TV

9

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

If “ACI ERROR” is displayed in the

AUTO PROGRAM menu:

“ACI ERROR” denotes that the ACI function

is not working properly. Press the 2 button

to start the ACI function again.

If “ACI ERROR” still appears even after you

have tried to start the ACI function several

times, press the 3 button to start the AUTO

PROGRAM function. It does not cause any

problem because all the TV channels are

registered to the Programme numbers (PR)

by the AUTO PROGRAM function.

 Downloading the data to VCR

You can transmit to the latest Programme

numbers (PR) data to the VCR with the T-V

LINK function.

Caution

• Only when the T-V LINK compatible

VCR is connected to the EXT-2

terminal, this operation is enabled.

• Only when the T-V LINK menu is being

displayed, this operation is enabled.

1 Turn on the VCR

2 Press the a

aa

a button

The data transmission begins.

The T-V LINK menu disappears once the

data transmission ends.

When the T-V LINK menu is

changed over to another menu:

The TV has finished its menu. This new

menu is operated from the VCR. See the

VCR instruction manual for what to do

next.

If “FEATURE NOT AVAILABLE”

appears at the T-V LINK menu:

Check the following three items. Then

press the 2

22

2 button to retry data

transmission.

• Has the T-V LINK compatible VCR

been connected to the EXT-2

terminal?

• Has the VCR power been turned on?

• Does the SCART cable that is

connected to the EXT-2 terminal to T-

V LINK compatible VCR have all

proper connections?

T-V LINK FUNCTIONS

When a T-V LINK compatible VCR is

connected to the EXT-2 Terminal on the TV,

it is easier to set up the VCR and to view

videos. T-V LINK uses the following

features:

To use T-V LINK functions:

A T-V LINK compatible VCR is necessary.

The VCR must be connected to the EXT-2

terminal on the TV by a fully wired SCART

cable.

A “T-V LINK compatible VCR” means a

JVC VCR with the T-V LINK logo or a VCR

with one of the following logos. However,

these VCRs may support some or all of the

features described below. For details, refer to

your VCR instruction manual.

“Q-LINK” (a trademark of Panasonic

Corporation)

“Data Logic” (a trademark of Metz

Corporation)

“Easy Link” (a trademark of Phillips

Corporation)

“Megalogic” (a trademark of Grundig

Corporation)

“SMARTLINK” (a trademark of Sony

Corporation)

D0005-EN

DOWNLOAD TV VCR

T-V LINK

OK

EXIT

D0037-EN

TRANSFER. . . . .

DOWNLOAD TV VCR

HV-36P38SUE_Eng.book Page 9 Friday, September 26, 2003 11:10 AM

10

Setting up your TV

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

 Pre-set Download

Download the registered data on the TV

channels from the TV to the VCR.

The Preset Download function automatically

begins when the initial setting is complete or

whenever the AUTO PROGRAM or EDIT/

MANUAL operations are performed.

• This function can be operated via VCR

operation.

When “FEATURE NOT AVAILABLE” is

displayed:

If “FEATURE NOT AVAILABLE” is

displayed, the download was not performed

correctly. Before trying to download again,

ensure the following:

• The VCR power is turned on.

• The VCR is T-V LINK compatible.

• The VCR is connected to the EXT-2

terminal.

• The SCART cable is fully wired.

 Direct Rec

“What You See Is What You Record”

You can record to VCR the images that you

are currently viewing on TV by a simple

operation. For details, read the manual for

your VCR. Operate via the VCR. “VCR IS

RECORDING” is displayed.

In the following conditions, the VCR

will stop recording if the TV is turned

off, if the TV channel or input is

switched, or if the menu is displayed

on the TV:

• When recording images from an external

device connected to the TV.

• When recording a TV channel after it has

been unscrambled on a decoder.

• When recording a TV channel by using

the TV’s output because that TV channel

cannot be properly received on the VCR’s

tuner.

• When the VCR is not ready (for example,

when there is no tape inserted), “NO

RECORDING” is displayed.

• Operation via the TV is not possible.

• Generally, the VCR cannot record a TV

channel that cannot be received properly

by the VCR’s tuner, even though you can

view that TV channel on the TV.

However, some VCRs can record a TV

channel by using the TV’s output if that

channel can be viewed on the TV, even

though the TV channel cannot be received

properly by the VCR’s tuner. For details,

refer to your VCR instruction manual.

HV-36P38SUE_Eng.book Page 10 Friday, September 26, 2003 11:10 AM

11

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

TV buttons and functions

Refer to the pages in parentheses for details.

1 Remote control sensor

2 Power lamp (pages 6, 12)

3 Main power button (pages 6, 12)

4 Headphone jack (mini jack) (page 40)

5 P p buttons/ q buttons (page 12)

6 r (Volume) button (page 12)

7 EXT-5 terminal (pages 37, 40)

Refer to the pages in parentheses for details.

1 Remote control sensor

2 Power lamp (pages 6, 12)

3 Main power button (pages 6, 12)

4 Headphone jack (mini jack) (page 40)

5 P p buttons/ q buttons (page 12)

6 r (Volume) button (page 12)

7 EXT-5 terminal (pages 37, 40)

R

P

L

S

EXT-5

R

P

L

S

EXT-5

HV-36P38SUE

R

L

S

P

E

X

T

5

R

L

S

P

E

X

T

5

EXT-1

EXT- 4

EXT-2

S

EXT-3

S

AUDIO OUT

L

Pr

Pb

R

L

Y

R

HV-32P37SUE/HV-28P37SUE

HV-36P38SUE_Eng.book Page 11 Friday, September 26, 2003 11:10 AM

12

TV buttons and functions

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Turn the Main power on

Press the Main power button on the

TV.

The Power lamp lights red and your TV is in

the standby mode.

• If the Power lamp lights green, the TV is

already on.

To turn the Main power off:

Press the Main power button again.

The Power lamp goes off.

Caution

• The main power button on the TV does

not fully isolate the TV from the AC

supply. If you are not going to use this TV

for a long period of time, be sure to

disconnect the AC plug from the AC

socket.

Turn the TV on from standby

mode

Press the P p

pp

p buttons to turn the TV

on from standby mode

Choose a TV channel

Press the P p

pp

p buttons to choose a

programme number (PR) or an EXT

terminal

Adjust the volume

1 Press the r

rr

r (Volume) button

The volume level indicator appears.

2 Press the q

qq

q buttons while the

volume level indicator is displayed

HV-36P38SUE_Eng.book Page 12 Friday, September 26, 2003 11:10 AM

13

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Remote control buttons and functions

1 Muting button

2 Number buttons

3 Information button

4 c button

5 3 sound button

6 b button

7 7 buttons

8 g (Text) button

9 p p buttons

0 VCR/DVD/Teletext control buttons

- p buttons

= # (Standby) button

~ VCR/TV/DVD switch

! G button

@ Colour button

# X (Multi) button

$ f/g (Freeze/Swap) button

% H button

^ a button

& b button

* r (Volume) q buttons

Turn the TV on or off from

standby mode

Press the #

##

# (Standby) button to turn

the TV on or off.

When the TV is turned on, the power lamp

changes from red to green.

• The power can be turned on by pressing

the b button, p p buttons or Number

buttons.

=

~

0

3

4

5

9

6

7

8

-

#

!

^

&

@

*

$

%

1

2

To turn the TV on or off, set the VCR/TV/

DVD switch on the remote control to the

TV position and press the # button.

If the VCR/TV/DVD switch on the remote

control is set to a position other than TV,

the TV will not be turned on or off even if

the # button is pressed.

HV-36P38SUE_Eng.book Page 13 Friday, September 26, 2003 11:10 AM

14

Remote control buttons and functions

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Choose a TV channel and

watch images from external

devices

• If the picture is tilted, correct it. See

“PICTURE TILT” on page 36.

 Use the number buttons:

Enter the programme number (PR)

of the channel using the number

buttons.

Example:

•PR 6 → press 6

• PR 12 → press 1 and 2

 Use the p

pp

p p

pp

p buttons:

Press the p

pp

p p

pp

p buttons to

choose the programme number

(PR) you want or an EXT terminal.

 Use the AV button:

Press the AV button to choose an

EXT terminal.

• You can choose a video input signal

from the S-VIDEO signal (Y/C signal)

and regular video signal (composite

signal). For details, see “S-IN (S-

VIDEO input)” on page 37.

• If you do not have a clear picture or no

colour appears, change the colour

system manually. See “COLOUR

SYSTEM” on page 26.

• If you choose an EXT terminal with no

input signal, the EXT terminal number

becomes fixed on the screen.

• This TV set has a function which can

automatically change over the input

according to a special signal output

from an external device. (The EXT-4

and EXT-5 terminals do not support

this function.)

• Since this TV is designed to make full

use of the resolution of the original

video source, the motion may appear

unnatural when the video source is

input with 625p progressive-scanning

component signals.

If this occurs, change the output setting

of the connected device to 625i

interlace-scanning component signal

output.

To return to a TV channel:

Press the b button, the p

p

buttons or

the Number buttons.

To use the Programme number PR 0

(AV):

When the TV and VCR are connected only

by the Aerial cable, choosing the Programme

number PR 0 (AV) allows you to view

images from the VCR. Set the VCR RF

channel to the Programme number PR 0

(AV) manually. For details, see “EDIT/

MANUAL” on page 32.

Pressing the G button changes the choice as

follows:

• The VCR RF channel is sent as the RF

signal from the VCR.

• Also refer to your VCR instruction

manual.

EXT-1

EXT-5

EXT-2

EXT-4

EXT-3

E3

S3

TV mode EXT modes

Programme

numbers

PR 1 – PR 99

or

EXT-1

EXT-5

EXT-2

EXT-4

EXT-3

E3

S3

TV mode

EXT modes

Programme

numbers

PR 1 – PR 99

or

PR 0

or

HV-36P38SUE_Eng.book Page 14 Friday, September 26, 2003 11:10 AM

Remote control buttons and functions

15

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

Adjust the volume

Press the r

rr

r q

qq

q buttons to adjust

the volume.

The Volume indicator appears and the

volume changes as you press the r q

buttons.

 Muting the sound

Press the

l

ll

l

(muting) button to

turn off the sound.

Pressing the

l

(muting) button again

restores the previous volume level.

Information function

You can see the channel number of the

programme you are watching, the current

time or the PR LIST.

From the PR LIST, you can choose a channel

or EXT terminal.

Press the

h

hh

h

(Information) button to

display the information you want to

see.

Pressing the

h

(Information) button changes

the display as follows:

Channel number display:

The channel number and channel name

(when the channel name is registered) of the

programme you are watching or the EXT

terminal number is displayed.

Time display:

The current time of the teletext data is

displayed.

If the TV has not received a TV channel that

has teletext programmes since it was turned

on, the time display is blank. To view the

current time, choose a TV channel that has

teletext programmes. The time will continue

to be displayed until the TV is turned off

even if you choose other TV channels.

• An incorrect current time is sometimes

displayed when watching videos.

PR LIST:

The programme number (PR) and EXT

terminal list is displayed.

Pressing the a button after choosing the

programme number (PR) or EXT terminal

with the 7 buttons will display the

chosen programme or EXT terminal.

• For programme numbers (PR) for which

the CHILD LOCK function is set, the n

(CHILD LOCK) mark is displayed. For

details see “CHILD LOCK” on page 29.

PR ID

AV

01

02

03

04

05

06

07

08

09

BBC1

D0011-EN

12 : 00

PR LIST

OK

+10-10

No indication

Channel number display

HV-36P38SUE_Eng.book Page 15 Friday, September 26, 2003 11:10 AM

16

Remote control buttons and functions

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

ZOOM function

You can change the screen size according to

the picture aspect ratio. Choose the optimum

one from the following ZOOM modes.

AUTO:

When a WSS (Wide Screen Signalling)

signal, which shows the aspect ratio of the

picture, is included in the broadcast signal or

the signal from an external device, the TV

automatically changes the ZOOM mode to

16:9 ZOOM mode or FULL mode according

to the WSS signal.

If a WSS signal is not included, the picture is

displayed in accordance with the ZOOM

mode set with the 4:3 AUTO ASPECT

function.

• For details of the 4:3 AUTO ASPECT

function, see “4:3 AUTO ASPECT” on

page 27.

• When the AUTO (WSS) mode does not

function correctly due to poor WSS signal

quality or when you want to change the

ZOOM mode, press the c button

and change to another ZOOM mode.

REGULAR:

Use to view a normal picture (4:3 aspect

ratio) as its original size is.

PANORAMIC:

This mode stretches the left and right sides of

a normal picture (4:3 Aspect Ratio) to fill the

screen, without making the picture appear

unnatural.

• The top and bottom of the picture are

slightly cut off.

14:9 ZOOM:

This mode zooms up the Wide Picture (14:9

Aspect Ratio) to the upper and lower limits

of the screen.

16:9 ZOOM:

This mode zooms up the Wide Picture (16:9

Aspect Ratio) to the full screen.

16:9 ZOOM SUBTITLE:

This mode zooms up the Wide Picture (16:9

Aspect Ratio) with subtitles to the full

screen.

FULL:

This mode uniformly stretches the left and

right sides of a normal picture (4:3 aspect

ratio) to fill the wide TV screen.

Use for pictures with a 16:9 aspect ratio that

have been squeezed into a normal picture

(4:3 aspect ratio), you can restore their

original dimensions.

 Choose the ZOOM mode

1 Press the c

cc

c button to display

the ZOOM menu

•The c button does not work in

the twin pictures mode.

D0009-EN

AUTO

REGULAR

PANORAMIC

14:9 ZOOM

16:9 ZOOM

16:9 ZOOM SUBTITLE

FULL

ZOOM

OK

HV-36P38SUE_Eng.book Page 16 Friday, September 26, 2003 11:10 AM

Remote control buttons and functions

17

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

2 Press the 6

66

6 buttons to choose a

ZOOM mode. Then press the a

aa

a

button

The picture expands and the chosen

ZOOM mode is displayed in about 5

seconds.

• The ZOOM mode may be

automatically changed due to the

control signal from an external device.

When you want to return to the

previous ZOOM mode, choose the

ZOOM mode again.

 Adjusting the visible area of the

picture

If subtitles or the top (or bottom) of the

picture are cut off, adjust the visible area of

the picture manually.

1 Press the c

cc

c button

The ZOOM menu appears.

2 Press the a

aa

a button to display the

ZOOM mode indication

Indicator is displayed.

3 While it is displayed, press the 6

66

6

buttons to adjust the visible area

vertically

• You cannot adjust the visible area in

REGULAR or FULL mode.

3D CINEMA SOUND function

You can enjoy sounds with a wider

ambience.

• This function does not work for the sound

from the headphones.

Press the 3

33

3 button and choose

“ON”, “MONO” or “OFF”.

ON:

Choose to add the 3D CINEMA SOUND

effect to stereo sound.

MONO:

Choose to add the 3D CINEMA SOUND

effect to monaural sound.

OFF:

Choose to cancel the 3D CINEMA SOUND

effect.

• The 3D CINEMA SOUND effect can be

adjusted with the “3D CINEMA

SOUND” menu (see page 28).

Return to TV channel instantly

You can return to a TV channel instantly.

Press the b

bb

b button

The TV returns to the TV mode and a TV

channel appears.

Using the FREEZE function

You can view the current programme as a

still picture.

1 Press the f

ff

f button

The still picture of the current picture will

appear.

16 : 9 ZOOM

D0010-EN

D0056-EN

current

programme

still picture

HV-36P38SUE_Eng.book Page 17 Friday, September 26, 2003 11:10 AM

18

Remote control buttons and functions

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

To cancel the FREEZE function:

Press the f button, the p p buttons or

the number buttons.

• The FREEZE function does not work

while a sub-picture is displayed.

• The still picture cannot be output from

the TV.

• The FREEZE function does not work

for pictures of 625p, 525p and 1125i

signals.

Using the MULTI-PICTURE

function

1 Press the X

XX

X button

The MULTI-PICTURE menu appears.

2 Press the 5

55

5 buttons to choose

the number of screens and then

press the a

aa

a button

2-pictures multi:

12-pictures multi:

• When set to 2-pictures multi, you can

view a TV picture and a picture from

an external device. You can not view a

TV picture on more than one screen at

the same time.

• When 12-pictures multi is set, pictures

from external devices are not

displayed.

• When set to 2-pictures multi, the main-

picture can be changed by pressing the

p p buttons. The sub-picture screen

can be changed by pressing the p

buttons.

When set to 12-pictures multi and

there are more than 12 pictures, the

next or previous 12 screens can be

displayed by pressing the p buttons.

• When set to 2-pictures multi, press the

g (swap) button to switch the main-

picture and sub-picture.

• 2-pictures multi function does not

work for a picture of 1125i signal.

• A picture of 625p or 525p signal

cannot be displayed as the sub-picture.

Pay attention to the following.

- When the EXT-4 picture is a picture

of 625p or 525p signal, you cannot

choose EXT-4 with the p buttons.

- When the EXT-4 picture signal is

changed to 625p, 525p or 1125i

signal while the EXT-4 picture is

displayed as the sub-picture, the 2-

pictures multi function is cancelled.

1

D0101-EN

212

D0102

1

D0103

2

D0104

12

Choose to return to one screen.

Choose to change to 2-pictures multi.

Choose to change to 12-pictures multi.

D0056-EN

Main-

picture

Sub-

picture

D0058-EN

Still

pictures

Moving

picture

Changing the sub-picture

Displaying the next or

previous 12 screens

HV-36P38SUE_Eng.book Page 18 Friday, September 26, 2003 11:10 AM

Remote control buttons and functions

19

ENGLISH

HV-36P38SUE/32/28P37SUE / LCT1537-001A-U / English

- The pictures cannot be swapped

when a picture of 625p or 525p

signal from EXT-4 is being

displayed as the main picture.

• Do not press the g (swap) button

while you are recording the TV output

on the VCR. If you do, the TV output

signal will change.

• You cannot view a scrambled channel

in the sub-picture. If the g (swap)

button is pressed when viewing a

scrambled channel in the main-picture

using an external decoder, the channel

you have been viewing in the sub-

picture will appear in both the main-

picture and sub-picture.

• When set to 2-pictures multi and the

headphones are connected, the sound

for the main-picture is output from the

TV speakers and the sound from the

sub-picture is output from the

headphones.

- Adjust the volume of the sub-picture

sound from the headphones with

“HEADPHONE VOLUME” in the

“SOUND” menu (see page 28).

- The main-picture sound can not be

heard through the headphones.

• When set to 12-pictures multi, press

the 7 buttons to choose the

screen you want to view and the press

the a button to display that picture

on the whole screen.

• The BLUE BACK function does not

work when the MULTI-PICTURE

function is being used.

• The ZOOM function does not work

when the MULTI-PICTURE function

is being used.

To return the multi-picture to one

screen:

Press the M button, press the 5

buttons to choose one screen, and then

press the a button.

• Pressing the b button will also return

the display to one screen.

Operating a JVC brand VCR or

DVD player

You can operate a JVC brand VCR or DVD

player. Pressing the button having the same

appearance as the original remote control

button of a device makes the function work

in the same way as the original remote

control.

1 Set the VCR/TV/DVD Switch to the

VCR or DVD position

VCR:

When you are operating the VCR, set the

switch to the VCR position.

• You can turn the VCR on or off with

the # (Standby) button.

DVD:

When you are operating the DVD player,

set the switch to the DVD position.

• You can turn the DVD player on or off

with the # (Standby) button.

2 Press the VCR/DVD Control Button

to control your VCR or DVD player

• If your device is not made by JVC,

these buttons cannot be used.

• Even if your device is made by JVC,

some of these buttons or any one of the

buttons may not work, depending on

the device.

• You can use the p buttons to choose

a TV channel. The VCR will receive or

choose the chapter the DVD player

plays back.

• Some DVD player models use the p

buttons for both operating of Fast

forward/backward functions and

choosing the chapter. In this case, the

253 buttons do not work.

You cannot turn the TV on or off when the

VCR/TV/DVD switch is set to the VCR or

DVD position.

When you turn the TV on or off, set the

VCR/TV/DVD switch to the TV position.

HV-36P38SUE_Eng.book Page 19 Friday, September 26, 2003 11:10 AM

Page is loading ...

JVC HV-36P38SUE, HV-32P37SUE, HV-28P37SUE User manual

JVC HV-36P38SUE, HV-32P37SUE, HV-28P37SUE User manual

Related papers

Other documents