Sanyo DWM-4500 User manual

Brand: Sanyo

Model: DWM-4500

Category: DVD players

Type: User manual

INSTRUCTION MANUAL

DVD Home Theater System

1AD6P1P2104--A DWM-4500, Issue Number 2

DWM-4500

SANYO’S HELP-LINE

Call the toll-free number below if you have any difficulties operating this product.

1-800-813-3435 (Weekdays: 7:30 AM - 4:00 PM Central Time)

English

Please Read This Manual.

Because DVD is a new technology, we recommend that you read this manual carefully before connecting your DVD

Home Theater System and operating it for the first time.

Keep the manual in a safe place for future reference.

-E1-

CONTENTS

Accessories ......................................................................... E2

Safety Certification ............................................................. E3

For Safe and Efficient Operation ....................................... E3

Warning for Transmitter ..................................................... E4

Controls ............................................................................... E5

Multi-Brand TV Remote Control......................................... E6

Basic Connections .............................................................. E8

System Cable Connection ............................................... E8

Speaker Connections .................................................... E10

Speaker Placement ........................................................ E11

Using the Rear Speaker in Wireless Mode ................... E12

Using the Rear Speaker in Wired Mode ........................ E12

If Using the External Speaker (Not Supplied) Instead of

the Rear Speaker... ....................................................... E12

Conventional TV Connection ......................................... E13

Using RF Modulator ................................................. E14

Progressive-scan TV Connection .................................. E15

Use of your VCR and Sanyo DVD Home Theater System

DWM-4500 .................................................................... E15

FM Antenna Connection ................................................ E16

Additional Connection Examples ................................... E16

Power Supply ................................................................ E16

Before Operation ............................................................... E17

Common Operation ....................................................... E17

Selecting Surround Mode .............................................. E18

Adjusting the Speaker Volume Balance ........................ E19

Adjusting the Sub-woofer Level ..................................... E19

Playable Discs ................................................................... E20

Disc Playback .................................................................... E21

Preparations .................................................................. E21

Basic Playback .............................................................. E22

Selecting Picture Mode ................................................. E22

Stopping Playback ......................................................... E23

Continuing Playback from Where You Stopped

Watching (LAST MEMO PLAY), for DVD only ............... E23

Selecting a DVD Menu .................................................. E23

Selecting a Top Menu [DVD] ......................................... E23

Chapter (Track) Skip ..................................................... E23

Title Search [DVD] ......................................................... E24

Chapter Search [DVD] ................................................... E24

Time Search [DVD] ........................................................ E24

Time Search [CD] .......................................................... E24

Track Search [CD] ......................................................... E24

Fast Playback ................................................................ E25

Slow Motion Playback [DVD] ......................................... E25

Still Picture (Pause) ....................................................... E25

Frame by Frame Advance Playback [DVD] ..................... E25

Picture Zoom [DVD] ...................................................... E25

Viewing from a Desired Camera Angle

(Multi-Angle) [DVD] ....................................................... E26

Designated Range Repeat Playback (A-B Repeat) ...... E26

Repeat Playback ........................................................... E26

Random Playback [CD] ................................................. E27

Programmed Playback [CD] .......................................... E27

Selecting Subtitle Language [DVD] ............................... E28

Selecting Audio Soundtrack Language

(Multi-Language) [DVD] ................................................. E28

Selecting On-Screen Information .................................. E28

TVGuardian Operation ...................................................... E29

Before Setting ................................................................ E29

Setting TVGuardian ....................................................... E29

How It Works After Setting TVGuardian ........................ E30

MP3/WMA CD Operation ................................................... E31

Before Starting .............................................................. E31

MP3 CD Playback ......................................................... E31

Picture Disc Operation ..................................................... E32

Before Starting .............................................................. E32

Kodak Picture/JPEG CD Playback ................................ E32

Initial Settings.................................................................... E33

Setting Language .......................................................... E33

Setting Display .............................................................. E34

Setting Audio ................................................................. E36

Setting Parental ............................................................. E37

Language Code List ...................................................... E38

Listening to the Radio (FM Only) ..................................... E39

Preparation .................................................................... E39

Automatic/Manual Tuning .............................................. E39

To Preset Stations ......................................................... E39

Listening to Preset Stations ........................................... E39

Enjoying Other Sources ................................................... E40

Sleep Timer Operation ...................................................... E40

Maintenance ...................................................................... E40

Troubleshooting Guide ..................................................... E40

Specifications .................................................................... E42

Warranty ............................................................................. E43

IMPORTANT INFORMATION:

To connect this DVD Home Theater System to a TV, TV must have a Video input jack (RCA-type) at least. You cannot

connect it to an antenna terminal of TV.

To operate the built-in TVGuardian

This unit has the built-in TVGuardian

Foul Language Filter (TVG

When a disc supporting closed caption is played, it will mute the audio during the entire phrase containing offensive

language. For more details, see page E29.

-E2-

Ferrite core x 2

This symbol indicates that dangerous voltage

constituting a risk of electric shock is present

within this unit.

This symbol indicates that there are impor-

tant operating and maintenance instructions

in the literature accompanying this unit.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION: TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: UNAUTHORIZED RECORDING OF COPY-

RIGHTED MATERIAL MAY VIOLATE APPLICABLE

NO RESPONSIBILITY FOR UNAUTHORIZED DUPLICA-

TION, USE OR OTHER ACTS WHICH INFRINGE UPON

THE RIGHTS OF COPYRIGHT OWNERS.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ACCESSORIES

RB-DWM4500MT wireless remote control

Video cable

FM indoor antenna lead wire

Either the main unit or remote control can be operated. However, for convenience, this instruction manual explains

operation using the remote control.

Note:

This handling description is printed prior to product development.

When a part of the product specification must be changed to improve operability or other functions, priority is given to the product

specification itself. In such instances, the instruction manual may not entirely match all the functions of the actual product.

Therefore, the actual product and packaging, as well as the name and illustration, may differ from the manual.

Front left speaker cable

Length: Approx. 16.4 feet (5 meters)

(Black and White)

Front right speaker cable

Length: Approx. 16.4 feet (5 meters)

(Black and Red)

Front center speaker cable

Length: Approx. 16.4 feet (5 meters)

(Black and Green)

Assistance speaker cable for rear

speaker

Length: Approx. 23 feet (7 meters)

The speaker cables are packed in the speaker package.

System cable

-E3-

• Do not damage the power cord.

• When not in use, disconnect the power cord from the outlet.

Grasp the plug, not the cord, when disconnecting the unit.

• If water should enter the unit, electrical shock or a malfunction

may result. Use in an area where there is low humidity and

little dust.

• Do not disassemble or alter the unit in any way.

• Do not use the unit in areas where extremes in temperature

occur (below 40°F (5°C) or exceeding 95°F (35°C)), or where

it may be exposed to direct sunlight.

• Because of the DVD video player’s extremely low noise and

wide dynamic range, there is a tendency to set the volume on

the amplifier higher than necessary. Doing so may produce

an excessively high output from the amplifier which can

cause damage to your speakers. Please be careful in this

regard.

• Sudden changes in the surrounding temperature can cause

dew to form on the optical pickup lens inside the unit. Under

this condition the unit may be unable to operate properly. If

this should occur, remove the disc and allow the unit to adjust

to the surrounding temperature.

FOR SAFE AND EFFICIENT OPERATION

CAUTION:

The sub-woofer (powered speaker) and the rear speaker

(powered speaker) must be placed in a well ventilated area.

Do not place any object on the top of these units.

Do not block ventilation holes.

The cabinet of these units warms up when it is used for a long

time, but it is not a malfunction.

• When carrying the unit, be sure to remove a disc which

may be inside and turn the power off. Then unplug the

power cord from the AC outlet after 10 seconds. Carrying

the unit with a disc inside may damage the disc and/or

the unit.

• The unit is automatically set to the Screen Saver mode

after approximately 5 minutes have elapsed under the

stop or pause mode.

SAFETY CERTIFICATION

This unit is made and tested to meet exacting safety

standards. It meets UL and FCC requirements and com-

plies with safety performance standards of the U.S. Depart-

ment of Health and Human Services.

CAUTION - USE OF CONTROLS OR ADJUSTMENTS

OR PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN HAZARD-

OUS RADIATION EXPOSURE.

THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED

BY ANYONE EXCEPT PROPERLY QUALIFIED SER-

VICE PERSONNEL.

FCC INFORMATION

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

CAUTION:

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate this equipment.

Note:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

-E4-

WARNING FOR TRANSMITTER

Important Information!

1. Explicitly specify to all users the technical instructions and

the scope of use defined in the related documents and

provide the explanation about all the control methods,

adjusting procedures and usage of switches.

2. Do not change the emitter frequency nor boost the emitter

power (including the power of excess load wireless frequency

power amplifier). Do not put up an external antenna nor use

any other remodeled antenna.

3. In use of this unit, avoid any act which interferes with legal

wireless communication services. Should any interference

arise, immediately stop using this unit, remove the interference,

and avoid such an act in the future.

4. When micro-power wireless equipment is used, avoid

interference with wireless communication services or emissive

interference from industrial, scientific and medical treatment

equipment.

5. Do not use this unit in an aircraft or near an airport.

Warning for using the sub-woofer with a built-

in transmitter

• Keep the sub-woofer (powered speaker) at least 8 feet

away from all heart pacemakers!

The radio waves may disrupt the operation of the

pacemaker.

• Do not operate this unit in medical Institutions, hospitals

or near medical equipment!

The radio waves may cause nearby equipment to

operate incorrectly or fail.

• When other equipment or a medical apparatus operates

incorrectly or fails to operate due to radio wave

interference, stop using this unit!

The radio waves may cause nearby equipment to

operate incorrectly or fail.

In-plant radio stations, and special low-power radio stations for

movable body identification used for production lines and

amateur radio stations as well as industrial, scientific and

medical equipment (such as microwave ovens) use the same

frequency band used by this unit.

1. Before using this unit, make sure that no in-plant radio

stations or special low-power radio stations for movable

body identification or amateur radio stations are operated

nearby.

2. If this unit should adversely radio-interfere with an in-plant

radio station for movable body identification, immediately

change the frequency band used by this unit or stop emitting

electric waves and consult the your dealer or SANYO service

center about measures for avoiding interference (for

example, installation of a partition).

3. If any trouble occurs such as this unit causing adverse radio

interference with special low-power radio stations for

movable body identification or an amateur radio station,

contact your SANYO dealer or SANYO service center.

Forbidden

-E5-

Main unit (DVD Receiver)

Rear speaker (Powered speaker)

1. Power switch (z/ON) and power indicator

2. Speaker switch (SPEAKER, back side) (See page E12.)

1. Frequency switch (FREQUENCY, back side) (See page E12.)

Sub-woofer (Powered speaker)

3. Frequency switch (FREQUENCY, top side) (See page E12.)

CONTROLS

1. Remote sensor (IR)

2. Function button (FUNCTION)

3. Volume buttons (- VOL +)

4. Power button (z/ON)

5. Display

6. Disc door

7. Play button (a)

8. Stop button (n)

9. Skip/Next/Previous/Preset tuning buttons

(f/e, -PRESET +)

10. Open/Close button (q)

11. S-video and Component video out select switch

(VIDEO OUT SELECT, right side)

(See pages E13 and E15.)

12 3 4 5 6 7 8 9 10 11

-E6-

1. Power button (z/ON)

2. Number and other function buttons

These buttons are used as number buttons and as function

buttons of each name.

• When using as a number button, press the appropriate

button directly.

• When using as a function button of each name, press the

appropriate button while holding the SHIFT button down.

Number buttons (1 – 9, 0)

Angle button (ANGLE)

Zoom button (ZOOM)

Audio button (AUDIO)

Sleep button (SLEEP)

3. TV control buttons

Power button (TV POWER)

TV/VIDEO select button (TV/VIDEO)

Channel scanning buttons (-TV CH +)

4. Tuner controls

FM mode button (FM MODE)

Tuner function button (TUNER)

Tuning buttons (- TUNE +)

Preset tuning buttons (- PRESET +)

5. Function button (FUNCTION)

6. Amplifier controls

Surround button (SURROUND)

Muting button (MUTE)

Bass button (BASS)

Sound preset button (SOUND)

Volume buttons (- VOLUME +)

7. Shift button (SHIFT)

8. Open/Close button (q)

9. Return button (RETURN) (See page E23.)

10. Clear/Trim button (CLEAR, TRIM)

Note:

At Trimming mode, press the button while holding the SHIFT

button down. (See page E19.)

11. Test tone button (TEST) (See page E19.)

12. Menu button (MENU)

13. Directional arrow buttons (o, a, p, b)

14. On-screen display button (ON SCREEN)

15. Play button (a)

16. Stop button (n)

17. Skip/Next/Previous buttons (f, e)

18. Repeat button (REPEAT)

19. A-B repeat button (A-B REP)

20. Subtitle change button (S.T.CH)

21. Last memory button (L.MEMO)

22. Picture mode/Search mode button

(PICTURE MODE/SEARCH MODE)

Note:

At Search mode, press the button while holding the SHIFT

button down.

23. Forward slow button (F.SLOW I a)

24. Reverse slow button (R.SLOW b I)

25. Fast forward/Fast reverse buttons (d, c)

26. Pause/Step button (k)

27. Top menu button (TOP MENU)

28. Enter button (ENTER)

29. Setup button (SETUP)

30. Program/Random play button (PROGRAM/RANDOM)

MULTI-BRAND TV REMOTE CONTROL

-E7-

To set the remote control code for TV

This remote control can operate the basic functions of TVs made

by the manufacturers listed below.

To enter the remote control code for your brand of TV, follow the

steps below.

1. In the chart below, find the code corresponding to your brand

of TV.

2. While holding down [TV POWER], enter the 2-digit code

using the number buttons [0 - 9], then release [TV POWER].

• The remote control is now set to operate your TV.

TV brands Code

ADMIRAL 05, 10, 13

EMERSON 17

FISHER 03

GE 07

GOLD STAR 01

HITACHI 02

JVC 15

MAGNAVOX 08

MATSUSHITA 12, 18

MITSUBISHI 14

PANASONIC 12, 18

QUASAR 12, 18

RCA 06

SAMSUNG 16

SANYO 03

SHARP 00, 13

SONY 11

TECHNOL ACE 05

TOSHIBA 04

ZENITH 09, 10

Notes:

• Only remote-controlled TVs can be operated using this remote

control. (Refer to your TV instruction manual for more details.)

• There may be some TV models that cannot be operated with

this remote control. If this is the case, use the original remote

control supplied with the TV.

IMPORTANT NOTE:

If the batteries in the remote control are changed, the code

settings for the TV must be re-entered.

Write your code number below for future reference.

TV:

Note:

This remote control cannot operate your VCR.

Inserting batteries

Note:

Remove the batteries if the remote control is not to be used for a

month or more. Batteries left in the unit may leak and cause

damage.

IMPORTANT NOTE:

SPENT OR DISCHARGED BATTERIES MUST BE

RECYCLED OR DISPOSED OF PROPERLY IN COMPLIANCE

WITH ALL APPLICABLE LAWS.

FOR DETAILED INFORMATION, CONTACT YOUR LOCAL

COUNTY SOLID WASTE AUTHORITY.

Remote control range

Two "AA" batteries

(not supplied)

Remote sensor

Within approx. 20 feet

(6 meters)

30°30°

-E8-

BASIC CONNECTIONS

Do not connect the power cord to a

120V AC 60Hz outlet until all connec-

tions have been made.

System cable from Main unit

(DVD Receiver)

Main unit (DVD Receiver)

Sub-woofer

(Powered speaker)

System cable to Sub-woofer (Powered speaker)

System cable

Attach the ferrite core.

Ferrite core

System Cable Connection

-E9-

Example: To use Main unit horizontally

Example: To hang Main unit on a wall

To unplug the system cable, pull out the plug (2) while pressing (1) down.

Main unitSub-woofer (Powered speaker)

Note:

Take care when installing it. It may cause damage or serious injury should it fall from its mountings.

Approx. 3/16 inch (5mm)

Approx. 5.4 inch (144mm)

Round head screw (not supplied)

Toward you

-E10-

After all speaker

connections have been

made, attach the ferrite

core.

Ferrite core

RedWhite

Green

BlackBlack

Black

Front right speakerFront left speaker Center speaker

Sub-woofer (Powered speaker)

System cable

Main unit (DVD Receiver)

Ferrite core

Note:

Do not connect the power cord to a 120V AC 60Hz outlet until all connections have been made.

Speaker Wire Color Use

Black and White Front left speaker

Black and Red Front right speaker

Black and Green Center speaker

Speaker Connections

To achieve proper stereo reproduction, connect the speaker

wires without shorting to adjacent wires as shown below.

SYSTEM (TO DVD RECEIVER)

SPEAKERS(4Ω)

FRONT

CENTER

-E11-

Example: To hang the speaker on a wall

Approx. 1/8 inch (3 mm)

Round head screw

(not supplied)

Note:

Take care when installing the speakers. They may cause

damage or serious injury should they fall from their

mountings.

Keep both the screw and stand for future use.

Unscrew and remove the stand.

Speaker Placement

Center speaker

Rear speaker (Powered speaker)

Sub-woofer

(Powered speaker)

Place it near the front speaker.

However, do not place it in front of

the TV.

Front left speaker

Front right speaker

The front (left and right) and center speakers have built-in magnetic

stray field compensation. They may be placed close to a TV

without affecting the color purity.

Place the front left and right speakers either side of the TV.

Place the center speaker directly above the TV.

The front, center, and rear speakers should be placed at

approximately the same distance from the listening position.

Place the rear speaker behind the listening position, on the floor

or approximately 2 feet ~ 3 feet 3 inches (60 cm ~ 1 meter) higher

than ear level.

Keep enough distance between the subwoofer and the TV so as

not to garble the TV screen.

Front left speaker Front right speaker

Center speaker

Rear speaker

Sub-woofer

Notes:

• The angles in the diagram are approximate.

• Please refer to “Setting Audio” on page E36.

• Set the TV’s built-in speaker volume to minimum.

30°30°

-E12-

Using the Rear Speaker in Wireless Mode

1. Set the SPEAKER switch of the rear speaker to the INTERNAL

position.

Changing the frequency setting

If noise (or skipping sound) is heard when using rear speaker in

wireless mode, change the setting of the FREQUENCY switch

on both sub-woofer and rear speaker.

Match the number on both sub-woofer and rear speaker.

It may improve the sounds.

The following four frequencies are available.

FREQUENCY switch

1 (914.1 MHz)

2 (914.5 MHz)

3 (914.9 MHz)

4 (915.3 MHz)

Using the Rear Speaker in Wired Mode

Because the rear speaker is the wireless type, it is not necessary

to connect the assistant speaker cable under normal connections.

If noise is caused to the rear speaker when used in wireless

mode, change the setting of the FREQUENCY switch on both

sub-woofer and rear speaker (Refer to the left column).

If noise is still caused, turn the power off first and connect the

rear speaker to the sub-woofer using the supplied assistant

speaker cable. In this case, the audio signal is sent to the rear

speaker through the assistant speaker cable.

Sub-woofer (powered speaker)

Assistant speaker cable

Note:

Adjust the distances between the sub-woofer and the rear speaker

to be suitable shorter than approx. 23 feet cord length.

If Using the External Speaker (Not Supplied)

Instead of the Rear Speaker...

1. Connect the external speaker (4 Ω, more than 50 Watts for

each speaker, not supplied) to the EXTERNAL SPEAKERS

terminal.

Front left speaker

Front right speaker

Center speaker

External rear

left speaker

(not supplied)

Sub-woofer

External rear

right speaker

(not supplied)

2. Pull out gently the antenna vertically.

• Try not to hold, bend, or twist the antenna.

Sub-woofer

(Powered speaker)

Rear speaker

(Powered speaker)

CAUTION:

Keep it out of reach of young children who might damage

it.

3. Set the FREQUENCY switch to “1”, “2”, “3” or “4”.

Match the number on both sub-woofer and rear speaker.

2. Set the SPEAKER switch to the EXTERNAL position.

3. Place the external speaker as shown in figure.

Sub-woofer

(Powered speaker)

External rear

right speaker

(not supplied)

External rear

left speaker

(not supplied)

Rear speaker

(Powered speaker)

Rear speaker

(Powered speaker)

Rear speaker (Powered

speaker)

To REAR OUT

jack

To REAR IN

jack

-E13-

Conventional TV Connection

Using VIDEO OUT jack

Connect the Video cable with yellow connectors (supplied)

between the VIDEO OUT jack of the sub-woofer and the VIDEO

INPUT jack on the TV.

Notes:

• Please refer to your TV instruction manual.

• When you connect the subwoofer to your TV, be sure to turn

off the power and disconnect both units from the wall outlet

until all the connections have been made.

• Do not connect the VIDEO OUT, S-VIDEO OUT, and

COMPONENT VIDEO OUT jacks of the sub-woofer to a VCR

directly. The playback picture will be distorted because DVD

video discs are copy protected.

*S-video cable (not supplied)

TV with S-VIDEO

INPUT jack

Sub-woofer (Powered speaker)

*Please consult your local audio/video dealer.

Important Information:

To connect the unit to a TV, TV must have a Video input jack

(RCA-type) at least. You cannot connect it to an antenna

terminal of TV.

Video cable (supplied)

To VIDEO INPUT jack

To VIDEO OUT jack (Yellow)

Sub-woofer (Powered speaker)

Using S-VIDEO OUT jack

Note:

Please follow the steps before turning on the power.

1. If your TV has the S-VIDEO INPUT jack, connect the *S-

video cable (not supplied) as shown in figure. (The VIDEO

OUT jack connection is not necessary.)

You can enjoy clearer picture playback.

Using COMPONENT VIDEO OUT jacks

Note:

Please follow the steps before turning on the power.

1. If your TV has the COMPONENT VIDEO INPUT jacks,

connect the *Component video cable (not supplied) as

shown in figure.

(The VIDEO OUT or S-VIDEO OUT jack connection is not

necessary.)

You can enjoy high quality picture playback.

TV with COMPONENT

VIDEO INPUT jacks

*Component Video cable (not supplied)

Red

Blue

Green

Sub-woofer (Powered speaker)

Red

Blue

Green

2. Set the VIDEO OUT SELECT switch to the S-VIDEO position.

2. Set the VIDEO OUT SELECT switch to the COMPONENT

position.

Main unit (Right side) Main unit (Right side)

-E14-

Using RF Modulator

If your TV does not have a Video input jack and has an antenna

terminal only, please purchase the *RF Modulator (not supplied).

(*Please consult your audio/video dealer.)

Example: Sub-woofer, TV and RF Modulator connections

1. Connect the antenna cable (not supplied) to the ANT. IN

terminal of the RF Modulator.

2. Connect the 75-ohm coaxial cable (not supplied) between

the TO TV terminal of the RF Modulator and the VHF/UHF

ANTENNA IN terminal of the TV.

3. Connect the Video cable with yellow connectors (supplied)

between the VIDEO OUT jack of the sub-woofer and the

VIDEO input jack of the RF Modulator.

Example: Sub-woofer, VCR, TV and RF Modulator connections

1. Connect the antenna cable (not supplied) to the VHF/UHF

FROM ANT IN terminal of the VCR.

2. Connect the 75-ohm coaxial cable (not supplied) between

the TO TV OUT terminal of the VCR and the ANT. IN

terminal of the RF Modulator.

3. Connect the 75-ohm coaxial cable (not supplied) between

the TO TV terminal of the RF Modulator and the VHF/UHF

ANTENNA IN terminal of the TV.

4. Connect the audio cables (not supplied) between the AUX

jacks of the unit and the AUDIO OUT jacks of the VCR. Use

the red connectors for the right-R jacks and the white

connectors for the left-L jacks.

5. Connect the Video cable with yellow connectors (supplied)

between the VIDEO OUT jack of the sub-woofer and the

VIDEO input jack of the RF Modulator.

6. Turn on the TV, and set the channel number (CHANNEL3 or

CHANNEL4) on all TV, VCR and RF Modulator, whichever

is not used for regular broadcasts in your area.

Note:

For more details, please refer to the instruction manual of the RF

Modulator.

4. Turn on the TV, and set the channel number (CHANNEL3 or

CHANNEL4) on both TV and RF Modulator, whichever is not

used for regular broadcasts in your area.

Note:

For more details, please refer to the instruction manual of the RF

Modulator.

To VIDEO OUT jack (Yellow)

Sub-woofer (Powered speaker)

Sub-woofer

(Powered speaker)

HiFi Stereo VCR

RF Modulator

-E15-

Note:

Please follow the steps before turning on the power.

1. Connect to the component video input jacks. (The VIDEO

OUT or S-VIDEO OUT jack connection is not necessary.)

*Please consult your local audio/video dealer.

*Component video cable (not supplied)

Green

Red

Blue

Green

Red

Blue

TV with progressive-scan capability

Progressive-scan TV Connection

Your TV must be capable of handling progressive scanning and have component video input capability.

2. Set the VIDEO OUT SELECT switch to the COMPONENT

position.

Progressive Scanning

While interlaced scanning produces one frame of video in two

fields, progressive scanning creates one frame in one field.

Conventional interlaced scanning constitutes one second with

30 frames (60 fields), but progressive scanning constitutes it with

60 frames from scratch. Progressive scanning can reproduce

sharper picture with high resolution for still image or other picture

containing long texts or horizontal lines.

This model has compliance with 525p (progressive) system.

Notes:

• Please refer to your TV instruction manual.

• When you connect the unit to your TV, be sure to turn off the

power and disconnect both units from the wall outlet until all

the connections have been made.

• Do not connect the unit to a VCR directly. The playback

picture will be distorted because DVD video discs are copy

protected.

Interlaced scanning

Progressive scanning

3. Set the unit to the PROGRESSIVE mode. See pages E21

and E35.

Sub-woofer (Powered speaker)

Main unit (Right side)

Use of your VCR and Sanyo DVD Home Theater System DWM-4500

1. We recommend that you connect your VCR sound output to

this Home Theater System.

Please test your VCR sound in Virtual 5.1 Channel Surround

Sound.

Connect the audio cables (not supplied) between the AUX

jacks of the Home Theater System and the AUDIO OUT

jacks of your VCR.

If your TV has the audio output jacks, you may replace this

VCR connection with TV connection.

Please refer to Additional Connection Examples to enjoy

your TV sounds on page E16 of the Instruction Manual.

2. We do not recommend that you connect your DVD Home

Theater System Video Output signal through your VCR and

then to your TV system.

DVD Video Disc Copy Protection Guard may affect your VCR

and you may not get a clear picture on your TV Display.

If you have any difficulties connecting your VCR with the use of

this Home Theater System, please call SANYO'S HELP-LINE

1-800-813-3435 (Weekdays: 7:30am - 4:00pm Central Time).

-E16-

PHONES

S-VIDEO

COMPONENT

VIDEO OUT

SELECT

PHONES jack

FM Antenna Connection

FM outdoor antenna

(not supplied)

Antenna discharge unit (not supplied)

FM indoor antenna

lead wire

75-ohm coaxial cable

(not supplied)

CAUTION:

When installing an outdoor antenna, follow the installation

instructions in the attached “IMPORTANT SAFETY

INSTRUCTIONS”.

Ground

Additional Connection Examples

Headphones jack (PHONES)

Connect a pair of stereo headphones with miniplug (8 ohms - 32

ohms, not available from SANYO) to the PHONES jack for

monitoring or for private listening. The speakers are automatically

disconnected when headphones are connected.

Audio cable (not supplied)

To enjoy your TV sounds

If your TV has the audio output jacks,

connect an audio cable (not supplied)

from the audio output jacks of the TV to

the AUX jacks.

The FM indoor antenna lead wire is sufficient to receive most

local FM broadcasts and should be connected to the rear FM

75Ω terminal. Extend the antenna lead wire as straight as possible

and, while listening to the sound from the system, secure it in a

position where the best FM reception is found.

In fringe areas, or where reception is distorted or noisy, an FM

outdoor antenna (not supplied) should be connected instead of

the FM indoor antenna lead wire. The terminals will accept 75-

ohm coaxial cable.

Note:

To minimize noise...

• Do not place the antenna close to a TV or speaker.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Section 820-40 of the NEC which provides guidelines

for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

Power Supply

(Sub-woofer and Rear Speaker)

Connect the power cord to a 120VAC 60Hz outlet.

The sub-woofer (powered speaker) and the rear speaker (powered

speaker) are equipped with a polarized plug. If you have difficulty

inserting the plug, turn it over and reinsert it. If these speakers

will not be used for a long time, disconnect the AC plug from the

AC outlet.

Notes:

• Before plugging the power cord into an AC outlet, make sure

that all the connections have been made.

• The sub-woofer (powered speaker) is not disconnected from

the AC power unless the power cord is unplugged from the

AC outlet.

Sub-woofer (Powered speaker)

Main unit (Right side)

Main unit (Left side)

-E17-

Common Operation

Turning the power on and off

Main unit (DVD Receiver)

BEFORE OPERATION

To reduce the volume temporarily (muting)

Press [MUTE] on the remote control. “MUTE” blinks on the

display.

To restore the previous volume setting, press [MUTE] again.

Selecting the sound mode

1. Press [SOUND] repeatedly to select the desired sound mode

(“BASS”, “TREBLE” or “NIGHT”).

2. Press the button as desired.

To turn the power off, press [z/ON] again.

Selecting the source

Press [FUNCTION] to select the desired source. Each time the

button is pressed, the display changes as follows:

DVD/CD v AUX v FM TUNER v DVD/CD...

• When the source selection is changed, disc playback

automatically stops.

Adjusting the volume

Press [VOLUME] + or - on the remote control (or press [VOL] + or

- on the main unit). The volume level appears on the display

(VOL 0 ~ VOL MAX).

Sound mode Press Display change

BASS p or o “-5” ~ “+5”

TREBLE p or o “-5” ~ “+5”

NIGHT ENTER “ON” or “OFF”

Note for “NIGHT” mode:

When enjoying a DVD disc with the volume set low at night,

select this mode. It enhances spoken lines making speech

clearer.

3. Repeat steps 1 to 2 for another sound mode.

4. Press [SOUND] repeatedly to close the display.

Bass boost system

Press [BASS] repeatedly to select the desired bass boost effect.

BOOST v BASS OFF v NORMAL v BOOST. . .

Adjusting the FL display brightness

While holding [n] down on the main unit, press [ON SCREEN]

repeatedly on the remote control.

Press [z/ON] to turn the power on.

• “HELLO” appears briefly on the display.

(After connecting the power cord, when you press [z/ON] for the

first time, the volume-reset feature automatically sets the initial

volume level.)

When the power cord is connected to the AC outlet, the unit will

respond to commands from the remote control.

To turn the power off, press [z/ON] again.

• “GOOD-BYE” appears briefly on the display.

Smart start function

If the following buttons are pressed when the power is turned

off, the unit turns on automatically and the selected source is

activated.

[q], [a] (Front panel of the main unit)

[q], [a], [TUNER] (Remote control)

Rear speaker

Press [z/ON] to turn the power on. The power indicator lights.

-E18-

Selecting Surround Mode

Press [SURROUND] to select the surround mode.

Each time the button is pressed, the surround mode changes as follows:

5.1 AUTO v 5.1 SURR v 2.1ch v DIRECT v 5.1 AUTO…

FL display

The unit selects the surround mode automatically depending on the disc.

• If a DVD disc is encoded with Dolby Digital 5.1 channel, it is played back with Dolby Digital 5.1

channel surround sound.

Not all DVD discs are encoded with Dolby Digital 5.1 channel surround sound.

• If a DVD disc is encoded with Dolby Digital 2 channel or mono, it is played back with Dolby Pro

Logic mode. “sPL” appears briefly on the display.

• If a DVD disc is encoded with 2 channel Linear PCM (stereo), it is played back with Dolby Pro

Logic mode. “sPL” appears briefly on the display.

• Audio CDs are played back with Dolby Pro Logic mode.

• MP3/WMA discs are played back with Virtual 5.1 channel surround sound.

Notes:

• When using headphones, the surround mode does not change. If [BASS] or [SURROUND] is pressed, “-BASS-” or “-SURR-”

appears briefly on the display.

• DVD video discs with DTS may not work correctly. You can see the picture on the TV screen, but there is no sound.

In this case, press the AUDIO button repeatedly while holding the SHIFT button down to select Dolby Digital sound. (See page E28.)

• When receiving weak FM broadcasts, set the mode to “2.1ch”. The sound quality may improve.

5.1 SURR

5.1 AUTODVD/CD

AUX

FM TUNER

(Stereo)

Function Description

2.1ch

5.1 AUTO

5.1 SURR

2.1ch

Disc is played back with Virtual 5.1 channel surround sound.

The surround mode is set to 2.1 channel (Front left and right speakers, and Sub-woofer).

The surround mode is set to Virtual 5.1 channel surround sound.

FM TUNER

(Mono)

The surround mode is set to 2.1 channel (Front left and right speakers, and Sub-woofer).

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

5.1 AUTO

5.1 SURR

Front left and right speakers, Center speaker, and Sub-woofer sound.

DIRECT Original audio signal from the disc

DIRECT Original audio signal

2.1ch The surround mode is set to 2.1 channel (Front left and right speakers, and Sub-woofer).

DIRECT Original audio signal

-E19-

Adjusting the Speaker Volume Balance

This unit is set to the standard level before shipping from the

factory. You may not need any adjustment.

However, depending on the size of the room and the placement

of the speakers, you may benefit from a fine adjustment.

In this case, follow the steps below. Please use the remote

control when the test tone sounds.

Note:

Do not connect the headphones.

1. Press [FUNCTION] to select “DVD/CD”.

2. Press [n] to stop playback completely.

3. Press [TEST] on the remote control.

The “Speaker” screen appears on the TV screen.

“FNT-L 0” appears on the display.

The test tone will be heard from each speaker sequentially as

follows:

TV screen FL display Speaker

Front-L FNT-L 0 Front left speaker

Center CENT 0 Center speaker

Front-R FNT-R 0 Front right speaker

Surround-R SUR-R 0 Rear (surround right) speaker

Surround-L SUR-L 0 Rear (surround left) speaker

Note:

There are Surround left and right speakers in the rear

speaker.

4. Press [VOLUME] + or - until the test tone becomes a

comfortable level.

5. If the test tone level is not the same from each speaker, press

[p] or [o] to adjust it while the speaker is activated.

The level appears on the TV screen and display.

Front-L: “-10” ~ “0” appears.

Center: “-10” ~ “+10” appears.

Front-R: “-10” ~ “0” appears.

Surround-R: “-10” ~ “+10” appears.

Surround-L: “-10” ~ “+10” appears.

If necessary, repeat this step again.

6. Press [TEST] to turn the test tone off.

Note:

If no adjustments are made, the original display returns after

the test tone has cycled around 5 times.

Adjusting the Sub-woofer Level

Note:

Do not connect the headphones.

1. Press [TRIM] while holding [SHIFT] down.

“FNT-L 0” appears on the display.

Note: No test tone.

2. Press [ENTER] repeatedly to select “SUB.W 0”.

Note:

Each time the button is pressed, the display will show the

selected speaker and tone level.

3. Press [p] or [o] to adjust the level as desired.

SUB.W: “-10” ~ “+10” appears.

Note:

If another speaker is selected, the level can also be changed

as above.

4. Press [TRIM] while holding [SHIFT] down to turn it off.

Note:

If no adjustments are made, the original display returns after

approximately 10 seconds.

IMPORTANT INFORMATION:

Set the delay time for your center and surround speakers. See

“Setting Audio” on page E36.

Page is loading ...

Sanyo DWM-4500 User manual

Brand: Sanyo

Model: DWM-4500

Category: DVD players

Type: User manual

Download PDF

report

Sanyo DWM-4500 User manual

Sanyo DWM-4500 User manual

Related papers

Other documents