CNB SKB-20Z12F/SKB-21Z12F Owner's manual

Brand: CNB

Model: SKB-20Z12F/SKB-21Z12F

Category: Security cameras

Type: Owner's manual

Interior PTZ Dome Camera SKB-20(1)Z12F

User’s Manual

Ver 1.14 (3812-0278B3)

Warnings

Cautions

◎ Read all of the safety and operating instructions before using the product.

◎ Save these instructions for future reference.

◎ Do not use attachments or accessories unless recommended by the appliance

manufacturer as they may cause hazards damage product and void warranty

CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.

NO USER SERVICEABLE PARTS INSIDE.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

Important Safeguard

This lightning flash with arrowhead symbol is intended to alert the

user to the presence of un-insulated "dangerous voltage" within the

product's enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons

manufacturer

they

may

cause

hazards

damage

product

and

void

warranty

◎ Do not use this product near water or moisture.

◎ Do not place or mount this product in or on an unstable or improperly supported location.

Improperly installed product may fall, causing serious injury to a child or adult, and

damage to the product. Use only with a mounting device recommended by the

manufacturer, or sold with the product. To insure proper mounting, follow the

ft 'it ti d l ti i ddb

REFER SERVICEING TO QUALIFIED SERVICE PERSONAL.

risk

electric

shock

persons

This exclamation point symbol is intended to alert the user to the

presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

manu

urer

ruc

ons an

use on

y moun

ng accessor

es recommen

manufacturer.

◎ This product should be operated only from the type of power source indicated on the

marking label.

Precautions

WARNING : TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK HAZARD,

DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE.

◎ Before using, make sure power supply and others are properly connected.

◎ While operating, if any abnormal condition or malfunction is observed, stop using the

camera immediately and then contact your local dealer.

◎ Do not disassemble or tamper with parts inside the camera.

◎ Do not drop or subject the camera to shock and vibration as this can damage camera.

◎ Care must be taken when you clean the clear dome cover. Especially, scratch and dust

will ruin your quality of camera.

◎ Do not install the camera in areas of extreme temperature, which exceed the allowable

range.

◎ Avoid installing in humid or dusty places.

◎ Avoid installing in places where radiation is present.

◎ Avoid installing in places where there are strong magnetic fields and electric signals.

◎ Avoid installing in places where the camera would be subject to strong vibrations.

◎ Never expose the camera to rain and water.

Features

Product

OSD MENU (Details)

------------------------------------------------- 6

SONY OSD

General Rules of Key Operation for Menu ---------------------------------------------- 24

------------------------------------------------- 8

Installation

Operation

MAIN MENU ------------------------------------------------------------------------------------- 24

MENU PASSWORD SETUP ---------------------------------------------------------------- 24

DISPLAY SETUP ------------------------------------------------------------------------------- 25

AREA LABEL SETUP ------------------------------------------------------------------------- 25

CAMERA SETUP ------------------------------------------------------------------------------ 26

IMAGE ADJUST SETUP --------------------------------------------------------------------- 26

WHITE BALANCE SETUP

------------------------------------------------- 9

------------------------------------------------- 18

Check points before Operation ------------------------------------------------------------------ 18

Preset and Pattern Function Pre-Check ------------------------------------------------------ 18

Starting OSD Menu --------------------------------------------------------------------------------- 19

Reserved Preset ------------------------------------------------------------------------------------- 19

PRESET

WHITE

BALANCE

SETUP

-------------------------------------------------------------------

AUTO EXPOSURE SETUP ---------------------------------------------------------------- 27

MOTION SETUP ------------------------------------------------------------------------------- 28

JOG SETUP ------------------------------------------------------------------------------------- 29

SYSTEM INITIALIZE -------------------------------------------------------------------------- 29

Pelco OSD

PRESET

-----------------------------------------------------------------------------------------------

SWING ------------------------------------------------------------------------------------------------- 20

PATTERN --------------------------------------------------------------------------------------------- 20

GROUP ------------------------------------------------------------------------------------------------- 21

Others Functions ------------------------------------------------------------------------------------ 22

Pelco

OSD

General Rules of Key Operation for Menu --------------------------------------------- 30

MAIN MENU ------------------------------------------------------------------------------------- 30

MENU PASSWORD SETUP ---------------------------------------------------------------- 30

DISPLAY SETUP ------------------------------------------------------------------------------- 31

Compass Direction Setup --------------------------------------------------------------------- 31

AREA LABEL SETUP ------------------------------------------------------------------------- 31

OSD Display of Main Screen --------------------------------------------------------------------- 23

CAMERA SETUP ------------------------------------------------------------------------------ 32

IMAGE ADJUST SETUP -------------------------------------------------------------------- 32

WHITE BALANCE SETUP ------------------------------------------------------------------ 32

AUTO EXPOSURE SETUP ---------------------------------------------------------------- 33

MOTION SETUP ------------------------------------------------------------------------------- 34

JOG SETUP ------------------------------------------------------------------------------------- 35

OSD MENU

-------------------------------------------- 24

Remote Controller

PARKING ACTION SETUP ----------------------------------------------------------------- 35

PRESET SETUP -------------------------------------------------------------------------------- 36

EDIT PRESET SCENE ----------------------------------------------------------------------- 36

EDIT PRESET LABEL ------------------------------------------------------------------------ 37

SWING SETUP --------------------------------------------------------------------------------- 38

PATTERN SETUP ----------------------------------------------------------------------------- 38

Specifications

-------------------------------------------- 46

-------------------------------------------- 48

EDIT PATTERN -------------------------------------------------------------------------------- 39

GROUP SETUP -------------------------------------------------------------------------------- 39

EDIT GROUP ------------------------------------------------------------------------------------ 40

SYSTEM INITIALIZE -------------------------------------------------------------------------- 42

◎ CCD Sensor : 1/4” Interline Transfer CCD

◎ 12x Optical Zoom, 12x Digital Zoom (Max. 144x Zoom)

◎

D&Niht

Fti

◎ With RS-485, 422 communication, max. 255 of cameras can be controlled at the same

time.

◎

Using the remote controller can control the camera (max 10 meters range)

Camera Specifications PTZ(Pan/Tilt/Zoom) Control

◎

unc

◎ Various Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus

◎ Independent & Simultaneous Camera Characteristic Setup in Preset operation

◎

Using

the

remote

controller

can

control

the

camera

(max

meters

range)

◎ Pelco-D, Pelco-P or SONY protocol can be selected as a control protocol in the current

version of firmware.

※ The function number to be supported for each protocol is different.

(Refer to the section titled “Each protocol function number”, Page 18)

Powerful Pan/Tilt Functions

◎ Max. 360°/sec high speed Pan/Tilt Movement for each preset

◎ Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path.

As a result, time to target view is reduced dramatically and the video on the monitor is

very natural to watch.

◎ For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached,

◎ OSD menu is provided to display the status of camera and to configure the functions

Powerful

Pan/Tilt

Functions

OSD(On Screen Display) Menu

it is very easy to locate camera to desired target view. Additionally it is easy to move

camera to a desired position with zoom-proportional pan/tilt movement.

◎

Max 127 Presets are assignable and characteristics of each preset can be set up

interactively.

◎ The information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be

displayed on screen.

Preset, Pattern, Swing, Group More..

◎

Max

127

Presets

are

assignable

and

characteristics

each

preset

can

set

independently, such as White Balance, Auto Exposure, Label and so on.

◎ Max. 8 set of Swing action can be stored. This enables to move camera repetitively

between two preset positions with designated speed.

◎ Max. 4 of Patterns can be recorded and played back. This enables to move camera to

follow any trajectory operated by joystick as closely as possible.

◎

M 8 t f G ti b t d Thi bl t titi l

◎

ax.

roup ac

on can

e s

ore

Thi

s ena

o move camera repe

titi

with combination of Preset or Pattern or Swing. A Group is composed of max. 20

entities of Preset/Pattern/Swings.

※ The function number to be supported for each protocol is different.

(Refer to the section titled “Each protocol function number”, Page 18)

6 7

◎ ID number of camera is set using dip switch. The example is shown below.

Basic Components

Camera ID Setup

Camera ID

Camera

101

202

303

404

Main Body Ceiling Bracket Product Bracket

ㆍㆍㆍ

14 0 E

15 0 F

16 1 0

Cable Cover Guide Pattern Manual

ㆍㆍㆍ

64 4 0

65 4 1

ㆍㆍㆍ

128 8 0

Remote Controller DC Adaptor Screws

129 8 1

ㆍㆍㆍ

255 F F

◎ The range of ID is 1~255. Do not use 0 as camera ID.

◎ Factory default of Camera ID is 1.

◎ If you want to control a certain camera, you must match the camera ID with

Cam ID setting of DVR or P/T controller.

※ SONY protocol, the camera ID can be set from 1 to 7.

If you set 7 or more for Camera ID, all is set to 7.

8 9

VISCA Cable

◎ Termination switch(Pin 6~7) is used in cases listed below.

Termination Switch Setting

◎ Select the appropriate Protocol with DIP switch combination. (Pin 1~3)

Communication Protocol Setup

◎ Long-distance communication between the controller and the camera (1-to-1

connection)

- When the connecting distance between the two units is especially long,

communication errors may occur due to the impedance of transmission cable. In this

Termination Switch is used in case listed below.

NO PROTOCOL BAUDRATE #1 #2 #3

0 SONY 9600bps OFF OFF OFF

1 SONY 38400bps ON OFF OFF

2 PELCO-D 2400bps OFF ON OFF

communication

errors

may

occur

due

the

impedance

transmission

cable.

this

case, set the termination switch of both units to ON.

◎ Controlling multiple cameras (Multiple connection)

- The camera may not operate correctly if multiple cameras are connected and

controlled. In this case, set the termination switch of the controller and the last

connected camera to ON and the switch of other cameras is OFF.

3 PELCO-D 9600bps ON ON OFF

4 PELCO-D 38400bps OFF OFF ON

5 PELCO-P 4800bps ON OFF ON

6 PELCO-P 9600bps OFF ON ON

Others

Reserved

◎ If you want to control using DVR or P/T controller, their protocol must be identical to

camera. Otherwise, you can not control the camera.

◎ If you changed camera protocol by changing DIP S/W, the change will be effective

after you reboot the camera.

Others

Reserved

RS485

RS422

10 11

#2 #n

① Install Ceiling Bracket on Ceiling.

④ Fix the camera with the fixing screw.

SKB-20(1)Z12F Installation

② Attach the product installation bracket to the camera.

⑤

I t th C bl C i t C ili B k t d fi it ith th li d fi i

⑤

nser

over

ili

rac

. an

ith

e supp

ng screw.

③ Line up the mold lines and assemble main body to ceiling bracket. Turn main body

on its axis in CW(Clockwise) direction and after assembling then.

12 13

◎ RS-485,422 Communication

- For PTZ control

connect this line to ke

board and DVR. To control multi

le cameras at

Cabling

,y p

the same time, RS-485,422 communication lines of them is connected in parallel as shown

below.

Image Output Device

RS485

RS422

◎ Power Connection

- The standard power for the system is 12V DC/1A .

Please, check the voltage and current capacity of rated power carefully.

Rated power is included in the back of main unit.

◎ Video Connection

- Cable does not provide.

◎S-video Connection

- Cable does not provide.

RATED POWER INPUT VOLTAGE RANGE CURRENT CONSUMPTION

12V DC

DC 12V ± 10%

14 15

Connection

◎ RS-422 supports connection method when using the controller. ◎ RS-485 supports connection method when using the controller.

Connection

3RXDIN

2 TXD IN

1 TXD IN

CNB Camera CNB CameraController

3RXDIN

RXD OUT+

2 TXD INTXD OUT-2

1 TXD OUT+ 1 TXD IN

3RXDIN

2 TXD IN

1 TXD IN

CNB Camera CNB CameraController

3RXDIN

RXD OUT+

2 TXD INTXD OUT-2

1 TXD OUT+ 1 TXD IN

9RXDOUT

8 RXD OUT

7 TXD OUT

6 TXD OUT

5 GND

4 RXD IN

RXD

5 GNDGND5

RXD

OUT+

4 RXD INRXD OUT-4

6 TXD OUT

7 TXD OUT

8 RXD OUT

9RXDOUT

8 RXD OUT

7 TXD OUT

6 TXD OUT

5 GND

4 RXD IN

RXD

5 GNDGND5

RXD

OUT+

4 RXD INRXD OUT-4

6 TXD OUT

7 TXD OUT

8 RXD OUT

9RXDOUT

RXD

OUT

RXD

OUT

RXD

OUT

RXD

OUT

16 17

• Function : Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function

can be configured for each application.

◎ Before power is applied, please check the cables carefully.

◎ The camera ID of the controller must be identical to that of the target camera.

Th ID b h k d b di DIP it h f th

Check points before operation

Starting OSD Menu

• Enter Menu : Go Preset[95]

e camera

can

e c

y rea

DIP

e camera.

◎ If your controller supports multi-protocols, the protocol must be changed to match to

that of the camera.

◎ If you changed camera protocol by changing DIP switch, the change will be effective

after you reboot the camera.

◎ Since the operation method can be different for each controller available, refer to the

Reserved Preset

• Description : Some Preset numbers are reserved to special functions.

• Function :

manual for your controller if camera can not be controlled properly. The operation of

this manual is based on the standard Pelco® Controller.

◎ Check how to operate preset and pattern function with controller or DVR in advance to

operate

camera function fully when using controller or DVR

Preset and Pattern Function Pre-Check

Go Preset[95] : Enters into OSD Menu.

Go Preset [131~134] : Runs Pattern Function 1~4

Go Preset[141~148] : Runs Swing Function 1~8

Go Preset[151~158] : Runs Group Function 1~8

• Function : Max. 127 positions can be stored as Preset position. The Preset number can be

assigned

from

128

but

reserved

for

starting

OSD

Camera

characteristics

operate

camera

function

fully

when

using

controller

DVR

◎ Refer to the following table when using standard Pelco® protocol controller.

PRESET

Go Preset Input [Preset No.] and press [Preset] button shortly.

Set Preset Input [Preset No.] and press [Preset] button for more than 2 seconds.

Run Pattern

Input [Pattern No ] and press [Pattern] button shortly

assigned

from

128

but

reserved

for

starting

OSD

Camera

characteristics

(i.e. White Balance, Auto Exposure) can be set up independently for each preset. Label

should be blank and "Camera Adjust“ should be set to "GLOBAL" as default. All haracteristics

can be set up in OSD menu.

• Set : Set Preset [1~128]

• Run : Go Preset [1~128]

• Delete :

To delete Preset use OSD menu

◎ If controller or DVR has no pattern button or function, use shortcut keys with preset numbers.

For more information, refer to “Reserved Preset” in this manual.

Run

Pattern

Input

[Pattern

]

and

press

[Pattern]

button

shortly

Set Pattern Input [Pattern No.] and press [Pattern] button for more than 2 seconds.

Eh lf i b

•

Delete

delete

Preset

use

OSD

protoco

unct

on num

Protocol

Function

SONY Pelco®

7 255

Preset

6 127

Swing

18 19

Swing

Pattern

Group

• Function : By using Swing function, you can make camera to move between 2 Preset

positions repeatedly. When swing function runs, camera moves from the preset

• Function : The group function allows running sequence of Presets, Pattern and/or Swings.

Max 8 group can be stored. Each group can have max 20 action entities which can be preset,

Ptt

SWING GROUP

ass

gne

eprese

ass

gne

en camera moves

from the preset assigned as the 2nd point to the preset assigned as the 1st point. Speed

can be set up from 1°/sec to 180°/sec. You can not set the same preset.

•Set:To set Swing, use OSD menu.

•Run:Method 1) Run Pattern [Swing NO.+10] ex) Run Swing 3 : Run Pattern [13]

Method 2) Go Preset [Swing NO.+140] ex) Run Swing 3 : Go Preset [143]

ern o

ng.

rese

spee

can

ese

up an

e repea

num

ern

ng can

be set up in Group setup. Dwell time between actions can be set up also.

Preset 1 Pattern 1 Swing 1

DWELL TIME

• Delete : To delete Swing, use OSD menu.

• Function : Pattern Function is that a camera memorizes the path (mostly curve path)

•Set:Use OSD menu to create a Group.

•Run:Method 1) Run Pattern [Group NO.+20] ex) Run Group 7 : Run Pattern [27]

PATTERN

Max. 20 Action

by joystick of controller for assigned time and revives the path exactly as it memorized.

4 Patterns are available and Maximum 1200 communication commands can be stored in

a pattern.

• Setting : Pattern can be created by one of following two methods.

Method 1) Set Pattern [Pattern NO.]

- Pattern editin

screen is dis

ed as bellow.

Method 2) Go Preset [Group NO.+150] ex) Run Group 7 : Go Preset [157]

• Delete : To delete Group, use OSD menu.

EDIT PATTERN 1

■

- Movement by Joystick and preset movement can be

memorized in a pattern.

- The rest memory size is displayed in progress bar.

- To save the recording, press NEAR key and to cancel,

press FAR key.

[NEAR:SAVE /FAR:DELETE ]

■

0/0/x1/N

┏ ┓

┗ ┛

Method 2) OSD using OSD menu: See the section “How to use OSD menu”.

•Run:Method 1) Run Pattern [Pattern NO.] ex) Run Pattern 2 : Run Pattern [2]

Method 2) Go Preset [Preset NO.+130] ex) Run Pattern 2 : Go Preset [132]

• Delete : To delete Pattern, use OSD menu.

20 21

•PWRUPACTION:This function enables to resume the last action executed before

power down. Most of actions such as Preset, Pattern, Swing and Group are available for

this

function

but

Jog

actions

are

not

available

resume

Other Functions

OSD Display of Main Screen

LABEL12345 PRESET Action TitlePreset Label

AREA01

A Lbl

this

function

but

Jog

actions

are

not

available

resume

• AUTO FLIP : In case that tilt angle arrives at the top of tilt orbit (90°), zoom module camera

keep moving to opposite tilt direction (190°) to keep tracing targets. As soon as zoom

module camera passes through the top of tilt direction(90°), images should be reversed

automatically and F appears in screen. If this function is set to OFF, tilt movement range is

5° ~95°.

Remote Control Information

ID:123

IRIS

IRIS Information

AREA01

rea

• PARKING ACTION : This function enables to locate the camera to specific position

automatically if operator doesn’t operate the controller for a while. The Park Time can be

defined as an interval from 1 minute to 4 hours.

• CAM ADJUST : WB(White Balance) and AE(Auto Exposure) can be set up independently

"Gl b l"

"L l"

Gl b l

• P/T/Z Information : Current Pan/Tilt angle in degree, zoom magnification and a compass

direction.

CAM 1

CAM 1 15/4/x1/N

Image Flip

Camera ID P/T/Z Information

Remote

Control

Information

ID:123

IRIS

Information

eac

prese

ere are

es,

"Gl

oca

means that WB or AE can be set up totally and simultaneously for all presets in "ZOOM

CAMERA SETUP" menu. The Local mode means that WB or AE can be set up

independently or separately for each preset in each preset setup menu. Each Local WB/AE

value should activate correspondingly when camera arrives at each preset location. During

Jog operation, Global WB/AE value should be applied. All Local WB/AE value do not

change

although

Global

WB/AE

value

changes

• Camera ID : Current Camera ID(Address).

• Action Title : Followings are possible Action Titles and their meaning.

“SET PRESETxxx” When Preset xxx is stored.

“PRESETxxx” When camera reach to Preset xxx.

change

although

Global

WB/AE

value

changes

• FOCUS MODE : This mode exchanges focus mode automatically between Manual Focus

mode and Auto Focus mode by operation. Manual Focus mode activates in preset

operation and Auto Focus mode activates during jog operation. With Manual mode at

presets, Focus data is memorized in each preset in advance and camera calls focus data in

correspondence with presets as soon as camera arrives at a preset. It should shorten time

• Preset Label : The Label stored for specific Preset.

“PATTERNx” When Pattern x is in action.

“SWINGx/PRESETxxx” When Swing x is in action.

“UNDEFINED” When undefined function is called to run.

to get focuses Focus mode changes to Auto Focus mode automaticall

when

og operation

starts.

• Image Flip : Shows that images are currently reversed by Auto Flip Function.

• Remote Control Information : This information shows current remote controller input value.

• IRIS Information : This information shows current iris value.

•AreaLabel:Indicate Label.

22 23

◎ The menu items surrounded with < > always has its sub menu.

◎ For all menu level, to go into sub menu, press NEAR key.

General Rules of Key Operation for Menu DISPLAY SETUP

DISPLAY SETUP

◎ This menu defines Enable/Disable of OSD display on

Main Screen. If an item is set to be AUTO, the item is

◎ To go to up-one-level menu, press FAR key.

◎ To move from items to item in the menu, use joystick in the UP/DOWN or LEFT/RGHT.

◎ To change a value of an item, use UP/DOWN of the joystick in the controller.

◎ Press NEAR key to save values and Press FAR key to cancel values.

AMERA ID

PTZ INFORMATION

BAC

AUTO

LANGUAGE

ENGLISH

displayed only when the value of it is changed.

•CAMERAID[ON/OFF]

•PTZINFORMATION[ON/OFF/AUTO]

• LANGUAGE [ENGLISH/中文/Korean]

- Support English, Chinese, Korean.

•AREALABELSETUP

• SYSTEM INFORMATION

- Displays system information and configuration.

• DISPLAY SETUP

MAIN MENU

SPEED DOME CAMERA

DISPLAY SETUP>

☞

EXIT

- Set LABEL name.

AREA LABEL SETUP

- Enable/Disable of OSD display on Main Screen.

• DOME CAMERA SETUP

- Configure various functions of this camera.

• SYSTEM INITIALIZE

- Initializes system configuration and sets all data to

factory default configuration.

DISPLAY

SETUP>

EXIT

◎ This menu defines Label related settings.

•DISPLAY[AUTO/ON/OFF]

• CLEAR AREA LABEL

- Default LABEL settings.

• EDIT SCENE

Edit

AREA LABEL SETUP

DISPLAY AUTO

CLEAR AERA LABEL CANCEL

☞

factory

default

configuration.

MENU PASSWORD SETUP

PASSWORD

ENABLE

[OFF/ON]

Edit

area.

• EDIT LABEL

- Edit LABEL.

※ Area setting can be configured rightward only and

Image Flip will be OFF. After setting IMAGE Flip will

return to the original status.

BACK

EXIT

MENU PASSWORD SETUP

PASSWORD ENABLE

☞

OFF

•

PASSWORD

ENABLE

[OFF/ON]

- Displays Password protection enabled/disabled.

• EDIT PASSWORD

- Sets 0~8 digits password.

※ Factory default password is “11111111”. Failure to

correctly input password more than 5 times will display

24 25

BACK

EXIT

KEY CODE message. Please contact retailer for the lost

of password or KEY CODE message.

• BACKLIGHT

[ECL(0~100)/WDR(W-REAR,W-MIDDLE,

FRONT)/

BLC(LOW

MIDDLE

HIGH)/OFF]

AUTO EXPOSURE SETUP

AE SETUP

▬

GLOBAL

BACKLIGHT

OFF

☞

◎ Setup the general functions of zoom camera module.

• FOCUS MODE [AUTO/MANUAL/SEMIAUTO]

CAMERA MODULE SETUP

FRONT)/

BLC(LOW

MIDDLE

HIGH)/OFF]

- Sets Backlight Compensation

•DAY/NIGHT[AUTO/DAY/NIGHT]

- it excute that change Day&Night in the lower luminance.

BACK

EXIT

DAY /NIGHT

BRIGHTNESS

IRIS

SHUTTER

AGC

3D-DNR

SENS

▬

<AUTO>

AUTO

ESC

HIGH

MIDDLE

<AUTO >

s camera

ocus mo

{ SEMIAUTO Mode

This mode exchanges focus mode automatically

between Manual Focus mode and Auto Focus mode.

Manual Focus mode activates in preset operation and

Auto Focus mode activates when jog operation starts.

With Manual mode at presets, Focus data is memorized

in each preset in advance and camera calls focus data

correspondence

with

presets

soon

camera

• BRIGHTNESS [0~100]

- Adjusts brightness of images. Iris, Shutter Speed and Gain are adjusted automatically in

correspondence with this value.

•IRIS[AUTO/MANUAL(0~100)]

hld

hi h t

iit

dj ti

Sh tt

hld

correspondence

with

presets

soon

camera

arrives at a preset.

• DIGITAL ZOOM [ON/OFF]

- Sets digital zoom function to ON/OFF. If this is set to OFF, optical zoom function runs but

zoom function stops at the end of optical zoom magnification.

• IMAGE FLIP [ON/OFF]

- If IMAGE FLIP is ON, Current image is reversed. If IMAGE FLIP is OFF, Reversed

ill

sse

ave

ity

pee

be fixed. If Iris is set to Manual, Iris should be fixed and Iris has lower priority in adjusting AE,

in comparison with others.

• SHUTTER SPEED [AUTO/A-FLK/MANUAL(x128~1/90000/OFF]

- If Iris is set to MANUAL and Shutter Speed is set to AUTO, Shutter Speed should have

highest

priority

Shutter

Speed

set

FLK

remove

Flicker

Shutter

Speed

should

mage w

ill

recove

oprev

ous s

us.

◎ Camera zoom settings associated with the module

to perform.

• SHARPNESS LEVEL [0~100]

Adjust

the

sharpness

the

picture

IMAGE ADJUST SETUP

IMAGE ADJUST

SHARPNESS LEVEL

GAMMA MODE

CRT

☞

highest

priority

Shutter

Speed

set

FLK

remove

Flicker

Shutter

Speed

should

set to 1/100 sec. for NTSC and 1/120 for PAL. If Shutter Mode is set to MANUAL, Shutter

speed is able to adjust from x128 to 1/90000.

•AGC[LOW/MIDDLE/HIGH/OFF]

- Enhances image brightness automatically in case that luminance level of image signal is too

low.

Adjust

the

sharpness

the

picture

• GAMMA MODE [CRT/LCD]

- Select the video output mode.

•STABILIZER[ON/OFF]

- Vibration and shaking of the image to compensate.

BACK

STABILIZER

EXIT

OFF

• 3D-DNR [LOW/MIDDLE/HIGH/OFF]

- Enhances images by deducting noises when gain level of images is too high.

• SENS-UP [AUTO(2~128)/OFF]

- Activates Slow Shutter function when luminance of image (signal) is too dark. It is possible to

set

the

maximum

number

frames

piled

one

another

Slow

Shutter

function

• WHITE BALANCE MODE [ATW/ AWB/ /INDOOR/

OUTDOOR/ MANUAL]

- Red and Blue level can be set up manually.

•REDGAIN[-100~100]

WHITE BALANCE SETUP

WHITE BALANCE SETUP -GLOBAL

WHITE BALANCE MODE

├

RED GAIN

└

BLUE GAIN

ATW

☞

26 27

set

the

maximum

number

frames

piled

one

another

Slow

Shutter

function

•BLUEGAIN[-100~100]

• RED ADJUST [-100~100]

•BLUEADJUST[-100~100]

BACK

EXIT

JOG SETUP

3D-DNR Day&Night BACKLIGHT

Exposure

OFF

Auto

D&N

OFF

WDR

ECL

BLC

◎ Setup the Jog speed and Direction.

• AUTO FLIP [ON/OFF]

※ Below is the reference table for various AUTO EXPOSURE functions.

AUTO FLIP

JOG MAX SPEED

JOG DIRECTION

BACK

120 /SEC

NORMAL

☞

Exposure

OFF

Auto

D&N

OFF

WDR

ECL

BLC

IRIS

AutoOOOOOOOO

ManualOOOOOXOO

AutoOOOOOOOO

A-FLKOOOOOOOO

- Refer to “Other Functions" section.

• JOG MAX SPEED [1°/SEC~200°/SEC]

- Sets maximum jog speed. Jog speed is inversely

proportional to zoom magnification. As zoom

magnification goes up, pan/tilt speed goes down.

• JOG DIRECTION

[

INVERSE/NORMAL

]

BACK

EXIT

Shutter

ManualOOOOOXOO

OFFOOOOOXOO

AGC

HighOOOOOOOO

MiddleOOOOOOOO

[

]

- If you set this to ‘NORMAL’, the view in the screen

is moving same direction with jog tilting.

If ‘INVERSE’ is selected, the view in the screen is

moving reversely.

SYSTEM INITIALIZE

MOTION SETUP

AGC

LowOOOOOOOO

OFF X O X O O X O O

•CLEAR

LL DAT

[YES/NO]

- Deletes all configuration data such as display, camera,

motion setup, password and so on.

• CLEAR DISPLAY SET [YES/NO]

- Initializes Display Configuration.

• CLEAR CAMERA SET [YES/NO]

Iitili

Cfi ti

SYSTEM INITIALIZE

CLEAR ALL DATA

├

CLEAR DISPLAY SET

├

CLEAR CAMERA SET

├

CLEAR MOTION SET

└

CLEAR EDIT DATA

REBOOT CAMERA

REBOOT SYSTEM

☞

◎ Setup the general functions of Pan/Tilt motions.

• MOTION LOCK [ON/OFF]

- If Motion Lock is set to ON, it is impossible to set up

and delete Preset, Swing, Pattern and Group. It is

possible

only

run

those

functions

set

and

MOTION

SETUP

MOTION SETUP

MOTION LOCK

OFF

☞

iti

zes

amera

gura

on.

• CLEAR MOTION SET [YES/NO]

- Initializes Motion Configuration.

•CLEAREDITDATA[YES/NO]

- Deletes Preset Data, Swing Data, Pattern Data and Group Data.

• REBOOT CAMERA [YES/NO]

BACK

EXIT

possible

only

run

those

functions

set

and

delete those functions, enter into OSD menu.

BACK

EXIT

28 29

- Reboots Zoom Camera module.

• REBOOT SYSTEM [YES/NO]

- Reboots Speed Dome Camera.

◎ The menu items surrounded with < > always has its sub menu.

◎ For all menu level, to go into sub menu, press NEAR key.

◎ To go to up-one-level menu, press FAR key.

◎

To move from items to item in the menu use joystick in the

UP/DOWN

LEFT/RGHT

General Rules of Key Operation for Menu

DISPLAY SETUP

CAMERA ID

PTZ INFORMATION

AUTO

☞

ACTION TITLE AUTO

◎ This menu defines Enable/Disable of OSD display

on Main Screen. If an item is set to be AUTO, the item

is displayed only when the value of it is changed.

•

CAMERA

[ON/OFF]

◎

move

from

items

item

the

use

joystick

the

UP/DOWN

LEFT/RGHT

◎ To change a value of an item, use UP/DOWN of the joystick in the controller.

◎ Press NEAR key to save values and Press FAR key to cancel values.

MAIN MENU

EXIT

BACK

PRESET LABEL

UTO

LANGUAGE ENGLISH

•

CAMERA

[ON/OFF]

•PTZINFORMATION[ON/OFF/AUTO]

• ACTION TITLE [ON/OFF/AUTO]

• PRESET LABEL [ON/OFF/AUTO]

• LANGUAGE [ENGLISH/中文/한국어]

- Support English, Chinese, Korean

NORTH

DIRECTION

SETUP

• SYSTEM INFORMATION

- Displays system information and configuration.

• DISPLAY SETUP

- Enable/Disable of OSD display on Main Screen.

OC S

MAIN

Compass Direction Setup

SPEED DOME CAMERA

☞

•

NORTH

DIRECTION

SETUP

•AREALABELSETUP

- Set LABEL name.

•D

AMERA

ETUP

- Configure various functions of this camera.

• SYSTEM INITIALIZE

- Initializes system configuration and sets all data to

factory default configuration.

◎ Set North to assign compass direction as criteria.

Move camera and press NEAR button to save.

EXIT

SET NORTH DIRECTION

┏ ┓

┗ ┛

MOVE TO TARGET POSITION

[NEAR :SAVE //FAR: :CANCEL ]

MENU PASSWORD SETUP

PASSWORD ENABLE

☞

OFF

• PASSWORD ENABLE [OFF/ON]

- Displays Password protection enabled/disabled.

AREA LABEL SETUP

◎

This menu defines Label related

settings

PASSWORD

ENABLE

BACK

EXIT

☞

OFF

• EDIT PASSWORD

-. Sets 0~8 digits password.

※ Factory default password is “11111111”. Failure to

correctly input password more than 5 times will display

KEY CODE message. Please contact retailer for the lost

assword or KEY CODE messa

◎

This

defines

Label

settings

•DISPLAY[AUTO/ON/OFF]

• CLEAR AREA LABEL

- Default LABEL settings.

• EDIT SCENE

-edit area.

EDIT

LABEL

AREA LABEL SETUP

DISPLAY AUTO

CLEAR AERA LABEL CANCEL

☞

30 31

•

EDIT

LABEL

- Edit LABEL.

※ Area setting can be configured rightward only and

Image Flip will be OFF. After setting IMAGE Flip will

return to the original status.

BACK

EXIT

◎ Setup the general functions of zoom camera module.

• FOCUS MODE [AUTO/MANUAL/SEMIAUTO]

CAMERA MODULE SETUP

• BACKLIGHT

[ECL(0~100)/WDR(W-REAR,W-MIDDLE,

FRONT)/

BLC(LOW

MIDDLE

HIGH)/OFF]

AUTO EXPOSURE SETUP

AE SETUP

▬

GLOBAL

BACKLIGHT

OFF

☞

s camera

ocus mo

{ SEMIAUTO Mode

This mode exchanges focus mode automatically

between Manual Focus mode and Auto Focus mode.

Manual Focus mode activates in preset operation and

Auto Focus mode activates when jog operation starts.

With Manual mode at presets, Focus data is memorized

in each preset in advance and camera calls focus data

correspondence

with

presets

soon

camera

FRONT)/

BLC(LOW

MIDDLE

HIGH)/OFF]

- Sets Backlight Compensation

•DAY/NIGHT[AUTO/DAY/NIGHT]

- it excute that change Day&Night in the lower luminance.

BACK

EXIT

DAY /NIGHT

BRIGHTNESS

IRIS

SHUTTER

AGC

3D-DNR

SENS

▬

<AUTO>

AUTO

ESC

HIGH

MIDDLE

<AUTO >

correspondence

with

presets

soon

camera

arrives at a preset.

• DIGITAL ZOOM [ON/OFF]

- Sets digital zoom function to ON/OFF. If this is set to OFF, optical zoom function runs but

zoom function stops at the end of optical zoom magnification.

• IMAGE FLIP [ON/OFF]

- If IMAGE FLIP is ON, Current image is reversed. If IMAGE FLIP is OFF, Reversed

ill

• BRIGHTNESS [0~100]

- Adjusts brightness of images. Iris, Shutter Speed and Gain are adjusted automatically in

correspondence with this value.

•IRIS[AUTO/MANUAL(0~100)]

hld

hi h t

iit

dj ti

Sh tt

hld

mage w

ill

recove

oprev

ous s

us.

◎ Camera zoom settings associated with the module

to perform.

• SHARPNESS LEVEL [0~100]

Adjust

the

sharpness

the

picture

IMAGE ADJUST SETUP

IMAGE ADJUST

SHARPNESS LEVEL

GAMMA MODE

CRT

☞

sse

ave

ity

pee

be fixed. If Iris is set to Manual, Iris should be fixed and Iris has lower priority in adjusting AE,

in comparison with others.

• SHUTTER SPEED [AUTO/A-FLK/MANUAL(x128~1/90000/OFF]

- If Iris is set to MANUAL and Shutter Speed is set to AUTO, Shutter Speed should have

highest

priority

Shutter

Speed

set

FLK

remove

Flicker

Shutter

Speed

should

Adjust

the

sharpness

the

picture

• GAMMA MODE [CRT/LCD]

- Select the video output mode.

•STABILIZER[ON/OFF]

- Vibration and shaking of the image to compensate.

BACK

STABILIZER

EXIT

OFF

highest

priority

Shutter

Speed

set

FLK

remove

Flicker

Shutter

Speed

should

set to 1/100 sec. for NTSC and 1/120 for PAL. If Shutter Mode is set to MANUAL, Shutter

speed is able to adjust from x128 to 1/90000.

•AGC[LOW/MIDDLE/HIGH/OFF]

- Enhances image brightness automatically in case that luminance level of image signal is too

low.

• WHITE BALANCE MODE [ATW/ AWB/ /INDOOR/

OUTDOOR/ MANUAL]

- Red and Blue level can be set up manually.

•REDGAIN[-100~100]

WHITE BALANCE SETUP

WHITE BALANCE SETUP -GLOBAL

WHITE BALANCE MODE

├

RED GAIN

└

BLUE GAIN

ATW

☞

• 3D-DNR [LOW/MIDDLE/HIGH/OFF]

- Enhances images by deducting noises when gain level of images is too high.

• SENS-UP [AUTO(2~128)/OFF]

- Activates Slow Shutter function when luminance of image (signal) is too dark. It is possible to

set

the

maximum

number

frames

piled

one

another

Slow

Shutter

function

32 33

•BLUEGAIN[-100~100]

• RED ADJUST [-100~100]

•BLUEADJUST[-100~100]

BACK

EXIT

set

the

maximum

number

frames

piled

one

another

Slow

Shutter

function

JOG SETUP

AUTO FLIP

☞

◎ Setup the Jog speed and Direction.

• AUTO FLIP [ON/OFF]

3D-DNR Day&Night BACKLIGHT

osure ON OFF Auto D&N OFF WDR ECL BLC

※ Below is the reference table for various AUTO EXPOSURE functions.

AUTO

FLIP

JOG MAX SPEED

JOG DIRECTION

BACK

EXIT

120 /SEC

NORMAL

☞

- Refer to “Other Functions" section.

• JOG MAX SPEED [1°/SEC~200°/SEC]

- Sets maximum jog speed. Jog speed is inversely

proportional to zoom magnification. As zoom

magnification goes up, pan/tilt speed goes down.

• JOG DIRECTION [INVERSE/NORMAL]

IRIS

AutoOOOOOOOO

ManualOOOOOXOO

Shutter

AutoOOOOOOOO

A-FLKOOOOOOOO

EXIT

- If you set this to ‘NORMAL’, the view in the

screen is moving same direction with jog tilting.

If ‘INVERSE’ is selected, the view in the screen is

moving reversely.

Shutter

ManualOOOOOXOO

OFFOOOOOXOO

AGC

HighOOOOOOOO

MiddleOOOOOOOO

◎ If Park Enable is set to ON, camera runs assigned

function automatically if there is no PTZ command

during assigned "Wait Time".

• PARK ENABLE [ON/OFF]

WAIT TIME

[1 i t 4h ]

MOTION SETUP

PARKING ACTION SETUP

PARK ENABLE

WAIT TIME

PARK ACTION

OFF

00 : 10: 00

HOME

☞

PARKING ACTION SETUP

OFF X O X O O X O O

◎ Setup the general functions of Pan/Tilt motions.

• MOTION LOCK [ON/OFF]

- If Motion Lock is set to ON, it is impossible to set

up and delete Preset, Swing, Pattern and Group.

It is possible only to run those functions. To set

up and delete those functions enter into OSD

•

WAIT

TIME

our

]

- The time is displayed with "hh:mm:ss" format and

you can change this by 1 min unit.

• PARK ACTION

[HOME/PRESET/PATTERN/SWING/GROUP]

{ HOME

Camera moves to home position if there is no

PTZ command during assigned "Wait Time".

PARK

ACTION

BACK

EXIT

HOME

MOTION SETUP

MOTION LOCK

POWER UP ACTION

FRZ IN PRESET

OFF

☞

< JOG SETUP >

< PARKING ACTION SETUP >

and

delete

those

functions

enter

into

OSD

menu.

•POWER UP ACTION [ON/OFF]

- Refer to “Other Functions" section.

• FRZ IN PRESET [ON/OFF]

- At start point of preset movement, camera starts freezing the image of start point.

Ckdilithi fttitdi t td

BACK

EXIT

amera

eeps

mage o

ng prese

movemen

oes no

display the images which camera gets during preset movement. As soon as camera

stops at preset end point, camera starts displaying live images which it gets at preset

end point. This function availability should be different by models.

34 35

• PRESET NO. [1~128]

- If a selected preset is already defined, camera

◎ Edits label to show on monitor when camera arrives

at presets. In Edit Label menu, a reverse

PRESET SETUP EDIT PRESET LABEL

EDIT LABEL-PRESET1PRESET SETUP

PRESET NO

☞

moves to pre-defined position and preset

characteristics such as Label and Relay Outputs

show on monitor. If a selected preset is not defined,

“UNDEFINED” shows on monitor.

• CLEAR PRESET [CANCEL/OK]

- Delete current Preset data

rectangular is cursor. As soon as finishing selecting

alphabet, cursor moves to the next digit.

◎ Using LEFT/RIGHT/UP/DOWN of joystick, move to

an appropriate character from the Character set

(■ )

↑

Current Cursor Position

[

■

]

23 4567 89

ABC DE F GH I

KLM NOPQ R S

UVW XY Z a b c

efg hi jk l m

opq r s t u v w

yz< >

▬

/: .

CANCEL

PRESET

CLEAR PRESET

CAM ADJUST

BACK

EXIT

UNDEFINED::

HOME

☞

GLOBAL

• EDIT PRESET SCENE

- Redefine current Preset scene position (i.e. PTZ).

• EDIT PRESET LABEL

- Edits Label to show on monitor when preset runs. MAX. 10 alphabets are allowed.

• CAM ADJUST [GLOBAL/LOCAL]

appropriate

character

from

the

Character

set

To choose that character, press the NEAR key.

• If you want to use blank, choose Space character (" ").

If you want to delete a character before, use backspace

character (" ←").

23 4567 89

ABC DEF GH I

KLM NOPQR S

UVWXYZ a b c

EXIT

- WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset.

There are 2 modes, "Global" mode & "Local" mode. The Global mode means that WB or

AE can be set up totally and simultaneously for all presets in "ZOOM CAMERA

SETUP“ menu. The Local mode means that WB or AE can be set up independently or

separately for each preset in each preset setup menu. Each Local WB/AE value should

activate corres

ondin

when camera arrives at each

reset location. Durin

◎ If you complete the Label editing, move cursor to "OK" and

press NEAR key to save completed label. To abort current

change, move cursor to "Cancel" and press NEAR key.

efg hi j k l m

opq rs t uv w

yz< >

▬

/: .

Space

Backspace

pgy

operation, Global WB/AE value should be applied. All Local WB/AE value should not

change although Global WB/AE value changes. If “Local’’

EDIT PRESET SCENE

◎ Using Joystick, move camera to desired position.

◎ By pressing NEAR key, save current PTZ data.

◎ Press FAR key to cancel.

EDIT SCENE-PRESET1

┏ ┓

┗ ┛

MOVE TO TARGET POSITION

[NEAR:SAVE /FAR:CANCEL]

36 37

• SWING NO. [1~8]

- Selects Swing number to edit. If a selected Swing

SWING SETUP EDIT PATTERN

SWING SETUP

SWING NO

☞

EDIT PATTERN1

■■■■■■■■■■■■■■■■■■■

has not defined, "NOT USED" is displayed in 1st

Position and 2nd Position.

• 1st POS, 2nd POS [PRESET 1~128]

- Set up the 2 position for Swing function.

If a selected preset is not defined, "UNDEFINED“

will be displayed as shown below.

NEAR

SWING

2ND POS .

BACK

EXIT

NOT USED

SWING SPEED

CLEAR SWING CANCEL

1ST POS .

30 /SEC

☞

MOVE TO START POSITION

[NEAR:START /FAR:CANCEL]

[NEAR: SAVE /FAR: DELETE ]

┏ ┓

┗ ┛

┏ ┓

┗ ┛

RUN SWING

◎ When swing function runs, camera moves from the preset assigned as the 1st point

to the preset assigned as the 2nd point. Then camera moves from the preset

assigned as the 2nd point to the preset assigned as the 1st point.

You can not set the same preset.

• SWING SPEED [1°/sec ~ 180°/sec]

◎ By using Joystick, move to start position with appropriate zoom. To start pattern

recording, press NEAR key. To exit this menu, press FAR key.

◎ Move camera with joystick of controller or run preset function to memorize the path

(mostly curve path) in a selected pattern. The total memory size and the rest memory

size is dis

ed in the form of bar. Maximum 1200 communication commands can be

EXIT

SWING SETUP

- Sets Swing speed from 1°/sec to 180°/sec.

• CLEAR SWING [CANCEL/OK]

- Deletes current Swing data.

• RUN SWING [GO/PREVIEW]

- GO initiates Swing. PREVIEW initiates Swing to preview.

stored in a pattern.

◎ To save data and exit, press NEAR key. To cancel recording and delete record data,

press FAR key.

SWING NO .

2ND POS .

PRESET 5

NOT USED

1ST POS .

☞

UNDEFINED

• PATTERN NO. [1~4]

- Selects Pattern number to edit.

If a selected pattern number is not defined

• GROUP NO. [1~8]

- Selects Group number to edit.

If a selected Group number is not defined,

"UNDEFINED" will be displayed under selected

PATTERN SETUP

GROUP SETUP

PATTERN SETUP

PATTERN NO . 1

☞

GROUP SETUP

GROUP NO .

CLEAR GROUP

☞

UNDEFINED

CANCEL

selected

pattern

number

not

defined

"UNDEFINED" will be displayed under selected

pattern number.

• CLEAR PATTERN [CANCEL/OK]

- Deletes data in current pattern.

• EDIT PATTERN

Starts editing pattern

Group number.

• CLEAR GROUP [CANCEL/OK]

- Deletes data in current Group.

• EDIT GROUP

- Starts editing Group.

• R

[GO/

PREVIEW

]

CLEAR PATTERN

BACK

EXIT

UNDEFINED

CANCEL

RUN PATTERN GO

BACK

EXIT

RUN GROUP

CANCEL

RUN GROUP GO

Starts

editing

pattern

• RUN PATTERN [GO/PREVIEW]

- GO initiates Pattern. PREVIEW initiates Pattern to preview.

U G OU [GO/ ]

- GO initiates Group. PREVIEW initiates Group to preview.

38 39

Page is loading ...

CNB SKB-20Z12F/SKB-21Z12F Owner's manual

Brand: CNB

Model: SKB-20Z12F/SKB-21Z12F

Category: Security cameras

Type: Owner's manual

Download PDF

report

CNB SKB-20Z12F/SKB-21Z12F Owner's manual

CNB SKB-20Z12F/SKB-21Z12F Owner's manual

Related papers

Other documents