Everpure EV3112 User manual

Brand: Everpure

Model: EV3112

Category: Water filters

Type: User manual

SELECTING A MOUNTING LOCATION

1. Give consideration to the weight of the unit when operating (ﬁlled with water). Operating weights

of High Flow CSR Systems are:

 • TwinSystem-45lbs(20.2kg)

 • TripleSystem-47lbs(21.2kg)

 • QuadSystem-49lbs(22.2kg)

 • QuadPlusSystem-49lbs(21.2kg)+separatesurge/storagetank@60lbs(27.2kg)

2. Thelocationshouldallowfor(Seegures1-8):

 • Minimumclearanceof2

⁄2"underthecartridge(s)soitcanbeloweredforremovaland

replacement.

 • Adequatespacefor“in”and“out”waterlineconnections.Benearadrainforushingandnear

a110VoutletiftheoptionalEverguard

™

LowPressureAlarmisused.

 • AdditionalmountingandoorspacefortheseparateSR-XFeederandsurge/storagetank

†

(Quad

Plus).

OPERATING SPECIFICATIONS*

Combined Model Name

Replacement

Cartridge

Flow Rate Capacity

HighFlowCSRTwin-MC MC 3.3gpm(12.5lpm) 18,000gal.(68,000L)

HighFlowCSRTwin-MC

3.3gpm(12.5lpm) 18,000gal.(68,000L)

HighFlowCSRTwin-XC XC 3.3gpm(12.5lpm) 18,000gal.(68,000L)

HighFlowCSRTwin-XC

3.3gpm(12.5lpm) 18,000gal.(68,000L)

HighFlowCSRTwin-4CB5 4CB5 3.3gpm(12.5lpm) 12,000gal.(45,400L)

HighFlowCSRTwin-7CB5 7CB5 5.0gpm(18.9lpm) 20,000gal.(75,700L)

HighFlowCSRTriple-MC MC 5.0gpm(18.9lpm) 27,000gal.(102,000L)

HighFlowCSRTriple-MC

5.0gpm(18.9lpm) 27,000gal.(102,000L)

HighFlowCSRTriple-XC XC 5.0gpm(18.9lpm) 36,000gal.(136,000L)

HighFlowCSRTriple-XC

5.0gpm(18.9lpm) 36,000gal.(136,000L)

HighFlowCSRTriple-4CB5 4CB5 5.0gpm(18.9lpm) 18,000gal.(68,000L)

HighFlowCSRTriple-7CB5 7CB5 7.5gpm(28.5lpm) 30,000gal.(113,550L)

HighFlowCSRQuad-MC MC 6.6gpm(25.2lpm) 36,000gal.(136,000L)

HighFlowCSRQuad-MC

6.6gpm(25.2lpm) 36,000gal.(136,000L)

HighFlowCSRQuadPlus-XC XC 6.6gpm(25.2lpm) 48,000gal.(181,600L)

HighFlowCSRQuadPlus-XC

6.6gpm(25.2lpm) 48,000gal.(181,600L)

*Forindividualcartridgespecications,refertocartridgeliterature.

Temperature: 35-100°F(2-38°C)

Pressure: 10-125psi(0.7-8.6bar),non-shock

For cold water use only.

INSTALLATION

1. Usethepredrilledmountingholesinthemanifoldbracketasguides.Markanddrillanchorholes.

Mountsecurely.SeeFigures5-8.

2. Shutoffpowertoequipment.IfsystemisaHighFlowCSRQuadPlus(separateSR-XFeederand

surge/storagetank

†

),proceedtostep3b.

3a. ConnectoutletportsofHighFlowsystemtoequipmentservedpertheinstructionsbelow.Always

useNSFapprovedpipedopeorTeontapeatallconnections.Useabackupwrenchonallttings

while connecting to avoid stress on the system components.

 • ThecrossttingbeforetheSR-XFeederhasathreadedoutletontop.Connectaminimum1/2"

I.D.linefromthisoutlettofountainbeverageequipment.

 • Thecrossttinghasaushingvalveinstalledonthebottom.Connecttubingtotheushingvalve

andruntodrain.Note:Somemunicipalplumbingcodesandgoodsanitarypracticesrequirean

air gap at the drain termination point.

Figure1–Twin

 EV3112-78RevEAP08

Installation and Operation Guide

High Flow CSR Filter Systems

Figure2–Triple

Figure4–QuadPlus

Figure3–Quad

ManufacturedbyEverpure

 • ConnecttheoutletoftheSR-XFeedertotheicemachinemake-upwater(notcondenserwater)

lineandcoffeebrewingequipment.Proceedtostep4.

3b.ForHighFlowCSRQuadPlusSystem,connectoutlettoequipmentservedpertheinstructionsbe-

low.AlwaysuseaNSFapprovedpipedopeorTeontapeatallconnections.Useabackupwrench

on all ﬁttings while connecting to avoid stress on the system components.

 • LocateandmounttheseparateSR-XFeederbetweentheHighFlowCSRsystemandtheice

machine.Make-upwater(notcondenserwater)lineandcoffeebrewingequipment.

 • Ateettingislocatedinthesystemheaderbeforethesurgetankisolationandushingvalve.

Usingminimum1/2"I.D.line,connecttheoutletofthisteetothefountainbeverageandremote

SR-XFeederline.Important: Install a tee in this service water line to separate the fountain

water feed from the ice machine/coffee brewer water feed.

In Massachusetts, a backﬂow preventer is required for this installation.

 • Connectonebranchoftheservicewaterteetothefountainbeverageequipment.Connectthe

otherbranchoftheteetotheinletoftheSR-XFeeder.ConnecttheoutletoftheSR-XFeederto

theicemachinemake-upwater(notcondenserwater)lineandcoffeebrewingequipment.

 • Thesurgetankisolationandushingvalveislocatedattheendofthesystemheader.Using

ttingsandhoseprovided,connectonebranchofthevalvetothesurge/storagetank.Connect

ahosefromtheother(ushing)branchandruntodrain.Note: Some municipal plumbing codes

and good sanitary practices require an air gap at the drain termination point.

4. Thesurge/storagetankispre-pressurizedto20psi.Checkpressureandadjustasnecessary.

5. Installamanualshut-offvalveleadingtothesystemforservicingandconnectminimum1/2"I.D.

(3/4"forquad)waterlinetothesysteminlet.

6. TheoptionalEverguard

™

LowPressureAlarm(LPA)consistsofapressureswitch,audible/visual

alarmboxandapoweradapter.Itisdesignedtodetectaxedlowpressure(approx.20psi)

conditionasanindicationoflossofsystemoutletpressureeitherduetoanintentionalshut-down

orexcessfoulingofthewaterlters,thusindicatingtheneedforltercartridgechange-out.Ifthe

systemisequippedwiththeLPA,followthesesteps:

 • Determinelocationofaconvenient110VACoutlettoplugintheLPApoweradapter.

 • Removetheprotectiverubbercapfromthepressureswitchinstalledinthesystemheader

assembly.InsertthewiresfromtheLPAunitthroughthecapandconnectthemtotheterminals

onthepressureswitch.Eitherwirecanbeconnectedtoeitherterminal.Replacethecap.

 • PlugtheLPApoweradapterintoanoutlet.Theaudiblealarmshouldactivate.Pushthereset

switch to silence.

 • UnplugtheLPAunit.

7. Shutoffthesysteminletvalvelocatedontheinletoftheprelterhead.

8. Checktobesuretheo-ringontheprelterhousingissufcientlylubricated.Useagoodgradeof

siliconelubricant,ifneeded.PositiontheEC210preltercartridgeonguideseatinthebottomof

thebowl.Thenthreadthebowlintotheheadbyhand.Useasumpwrenchtosnugthebowlonto

the head.

9. InstallonlygenuineEverpure™carbonltercartridge(s)intothelterhead(s)followingdirections

onthecartridgelabelorasshownintheCartridgeChangeillustrations.InstalltheSS-10Scale

InhibitorcartridgeintotheSR-Xhousing.

10.Turnoninletwatertotheltersystemandcheckforleaks.

11.Opentheushingvalveandushthecartridge(s)byrunningwaterthroughatfullforceforve

minutes.Thiswillsetthelteringmediaandpurgeanyairandnes,insuringmaximumlterlife.

See illustrations.

12.Afterushing,closetheushingvalve,turnonpowertoequipmentandplugtheLPA(ifso

equipped)intotheelectricaloutlet.Thesystemisreadyforoperation.

Figure5–HighFlowCSRTwin

25.80"

ICE MACHINE/

COFFEE

OUTLET

3/4" FNPT

INLET

3/4" FNPT

FOUNTAIN

OUTLET

3/4" FNPT

25.59"

Figure6–HighFlowCSRTriple

25.59"

30"

INLET

3/4" FNPT

ICE MACHINE/

COFFEE

OUTLET

3/4" FNPT

FOUNTAIN

OUTLET

3/4" FNPT

Figure8–HighFlowCSRQuadPlus

29.69"

OUTLET

3/4" FNPT

INLET

3/4" FNPT

ICE MACHINE/

COFFEE

OUTLET

3/4" FNPT

INLET

3/4" FNPT

INSERT TEE FITTING.

ONE OUTLET TO FOUNTAIN,

ONE OUTLET TO SRX.

31.38"

Figure7–HighFlowCSRQuad

34"

INLET

3/4" FNPT

ICE MACHINE/

COFFEE

OUTLET

3/4" FNPT

FOUNTAIN

OUTLET

3/4" FNPT

25.69"

Checkforcompliancewithstateandlocallawsand

regulations.TheCommonwealthofMassachusetts

PlumbingCode248CMRshallbeadheredto.Consultyour

locallicensedplumberforinstallationofthissystem.Do

notusewithwaterthatismicrobiologicallyunsafeorof

unknownqualitywithoutadequatedisinfectionbeforeor

after the system. Systems certiﬁed for cyst reduction may

beusedondisinfectedwatersthatmaycontainlterable

cysts.

FLUSHING

For maximum life, all carbon ﬁlter cartridges must be ﬂushed for ﬁve minutes at full ﬂow before use. ALL

NEW CARTRIDGES MUST BE FLUSHED AFTER EACH CARTRIDGE CHANGE BEFORE BEING PUT INTO SERVICE!

Ifthecartridgesarenew,havebeenproperlyushedandbothneedleandfollowerregisterinadequatepressure,or

theLPAissounding,youmaybeexperiencinginadequatewaterpressureorsomerestrictionmayexistintheinlet

waterline.Ineithercase,theincomingwaterpressuremustbeimprovedtoreceiveoptimumlterlife.

COMPLETECARTRIDGECHANGEINSTRUCTIONSCANBEFOUNDONTHEFILTERCARTRIDGELABEL.

Not for residential use. For food service applications only.

CARTRIDGE CHANGE PROCEDURE

E-Series Preﬁlter Cartridge Change

1. Shutoffpowertoequipment.Shut

off inlet water ahead of system.

2. Pushredreliefvalve.Unscrew

bowl.Removepreltercartridge.

3. Cleanbowlwithlteredwateronly;

NOSPECIALCLEANERS.

4. Feelheado-ring.Ifdry,lubricate

withhighqualitysiliconelubricant.

5. Installnewpreltercartridgein

bowl.Handtightenbowlontohead.

6. Turnonwater.Turnonpowerto

equipment.

Everpure Carbon Filter Cartridge

Change

1. Shutoffpowertoequipment.Shut

off inlet water ahead of system.

2. Openushingvalvetorelieve

pressure.

3. Hold head ﬁrmly and push upward.

Turncartridgetoleftuntilitstops.

4. Pullcartridgedownwardandoutof

head.

5. Holdheadrmly.Aligncartridge

lugwithlabel.Insertnewcartridge

ﬁrmly into head.

6. Turncartridgeright90˚until

rotation stops.

7. Repeatsteps3-6forremaining

cartridges.

Flushing

8. Withushingvalvefullyopen,open

inlet water at full force for ﬁve

minutes.Closeushingvalve.

9. Turnonpowertoequipment

PRESSURE GAUGES

Low Inlet

Pressure

Adequate Inlet

Pressure

Low Outlet

Pressure

Adequate Outlet

Pressure

SR-X Feeder Cartridge Change

1. Shutoffpowertoequipment.Shut

off inlet water ahead of system.

2. Pressredpressurereliefbuttonon

head.

3. Unscrewbowl.

4. Removeoldcartridge.

5. Feelbowlo-ring;ifdry,lubricate

withsiliconelubricant.

6. InstallnewSS-10cartridgeinto

head.

7. Handtightenbowlintohead.

8. Turnonwater.

9. Pressredpressurereliefbutton

until water comes out of valve port.

10.Turnonpowertoequipment.

For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed

plumber for installation of the system. This system and its installation must comply with state and local regulations.

CARTRIDGE CHANGE DETERMINATION

Replacethepreltercartridgewheneveritbecomesexcessivelydirty(observedvisuallyorbyowrestriction).Followthechangeinstructionsprovidedwith

thecartridge.Replacecarbonltercartridgeswhencapacityisreachedorwhenowbecomesinadequate,butatleastannually.Allcarbonltercartridges

onmultiplecartridgesystemsshouldbechangedatthesametime.ChangetheSS-10cartridgewhenproductlevelinthecartridgedropsbelow1/2"from

thebottomofthebowl.

ThesystempressuregaugeoroptionalEverguard

™

LowPressureAlarm(LPA)providesaquick,simplemeansofdeterminingwhentheltercartridge(s)

shouldbechecked.Installedonthesystemoutletmanifold,thegaugeorLPAcanbeusedtomonitorbothdynamic(owing)andstatic(line)pressure.The

cartridge(s)shouldbechangedwhenthepressuregaugeisintheredareawhileequipmentisinoperation,andyettheneedleshowsadequatelinepressure

betweencycles.Observetheneedleduringthenextequipmentoncycle.Iftheneedleregistersadequatepressure,itcanbeassumedthatthetemporary

low-pressureconditionwascausedbyabriefpowerfailureorotherincomingpressuredisruption.Ifthelowpressureconditionisnotduetoanexternal

condition,check/changetheprelterrst.Ifthelowpressureconditionisstillnotcorrected,changethecarbonltercartridges.

For sales, replacement components, and service, contact your Everpure dealer or:

Everpure, LLC: 1040MuireldDrive•HanoverPark,Illinois60133•800.323.7873

In Europe: Toekomstlaan30•B-2200Herentals,Belguim

In Japan: HashimotoMNBldg.7F•3-25-1HashimotoSagamihara-Shi•Kanagawa229-1103,Japan

PrintedinU.S.A. EV3112-78RevEAP08

Technical Service

800.942.1153

www.everpure.com

LIMITED WARRANTY

COMMERCIAL WATER TREATMENT EQUIPMENT

Youhavejustpurchasedoneofthenestwatertreatmentunitsmade.AsanexpressionofourcondenceinEverpureproducts,thisproductiswarrantedagainstdefectsin

materialandworkmanshiptotheoriginalend-userwheninstalledinaccordancewithEverpurespecications.Thewarrantyperiodcommencesfromthedateofpurchase

and is administered as follows:

For a period of ONE YEAR Replaceable elements (i.e., ﬁlter & water treatment cartridges)*

For a period of FIVE YEARS The entire system (excluding replaceable elements)

*This is for material & workmanship, not ﬁlter or water treatment cartridge life.

TheunitmustbeusedinoperatingconditionsthatconformtoEverpure’srecommendeddesignguidelines.Thiswarrantywillnotapplyiftheunithasbeenmodied,repaired

oralteredbysomeonenotauthorizedbyEverpure.

If a part described above is found defective within the speciﬁed period, you should notify Everpure technical service at the phone number listed below. Any part

found defective within the terms of this warranty will be repaired or replaced (at Everpure’s discretion) by your local dealer or Everpure technical service. You

pay only freight from our factory and local dealer charges. Any repaired or replaced warranty item will be incorporated under the original warranty terms of the

existing system.

Wearenotresponsiblefordamagecausedbyaccident,re,ood,freezing,ActofGod,misuse,misapplication,neglect,oxidizingagents(suchaschlorine,ozone,

chloraminesandotherrelatedcomponents),alteration,installationoroperationcontrarytoourprintedinstructions,orbytheuseofaccessoriesorcomponentswhichdonot

meetEverpure’sspecications.RefertothespecicationssectionintheInstallationandOperatingmanualforapprovedapplicationparameters.

Ourproductperformancespecicationsarefurnishedwitheachwatertreatmentunit.TOTHEEXTENTPERMITTEDBYLAW,EVERPUREDISCLAIMSALLIMPLIEDWARRANTIES,

INCLUDINGWITHOUTLIMITATIONWARRANTIESOFMERCHANTABILITYANDFITNESSFORPARTICULARPURPOSE;TOTHEEXTENTREQUIREDBYLAW,ANYSUCHIMPLIED

WARRANTIESARELIMITEDINDURATIONTOTHEPERIODSPECIFIEDABOVEFORTHEENTIREWATERTREATMENTUNIT.Asamanufacturer,wedonotknowthecharacteristics

ofyourwatersupplyorthepurposeforwhichyouarepurchasingthisproduct.Thequalityofwatersuppliesmayvaryseasonallyoroveraperiodoftime,andyourwater

usageratemayvaryaswell.Watercharacteristicscanalsodifferconsiderablyifthisproductismovedtoanewlocation.Forthesereasons,weassumenoliabilityforthe

determinationoftheproperequipmentnecessarytomeetyourrequirements,andwedonotauthorizeotherstoassumesuchobligationsforus.Further,weassumeno

liabilityandextendnowarranties,expressorimplied,fortheuseofthisproductwithanon-potablewatersourceorawatersourcewhichdoesnotmeettheconditionsfor

usedescribedintheowner’sguideorperformancedatasheetforthisproduct.OUROBLIGATIONSUNDERTHISWARRANTYARELIMITEDTOTHEREPAIRORREPLACEMENT

(ATEVERPURE’SDISCRETION)OFTHEFAILEDPARTSOFTHEWATERTREATMENTUNIT,ANDWEASSUMENOLIABILITYWHATSOEVERFORDIRECT,INDIRECT,INCIDENTAL,

CONSEQUENTIAL,SPECIAL,GENERALOROTHERDAMAGES.

Somestatesdonotallowtheexclusionofimpliedwarrantiesorlimitationsonhowlonganimpliedwarrantylasts,sotheabovelimitationmaynotapplytoyou.Similarly,

somestatesdonotallowtheexclusionofincidentalorconsequentialdamages,sotheabovelimitationorexclusionmaynotapplytoyou.Thiswarrantygivesyouspecic

legalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.ConsultyourtelephonedirectoryforyourlocalindependentlyoperatedEverpuredealer,or

writeEverpureforwarrantyandserviceinformation.

REPLACEMENT PARTS

ContactyourlocalEverpuredealerforltercartridgesorsystemreplace-

ment parts.

Description Part Number

Inlet/outletpressuregauge EV3114-09

Inlet/ushingvalve EV3114-07

O-ringforprelterorSR-X EV3112-40

Prelterbowl EV3112-38

SR-Xbowl EV3112-39

LPApressureswitch EV3016-41

Wrench EV3112-41