SMC Networks SMC8950EM User manual

INSTALLATION GUIDE

ta

SMC8926EM

SMC8950EM

TigerStack II 10/100/1000

24/48-Port Stackable Layer 3 Gigabit

Switch

20 Mason

Irvine, CA 92618

Phone: (949) 679-8000

TigerStack II 10/100/1000

Installation Guide

From SMC's Tiger line of feature-rich workgroup LAN solutions

August 2009

Pub. # 150200000054A

E082009-MW-R01

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and

reliable. However, no responsibility is assumed by SMC for its use, nor for any

infringements of patents or other rights of third parties which may result from its use. No

license is granted by implication or otherwise under any patent or patent rights of SMC.

SMC reserves the right to change specifications at any time without notice.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are

trademarks of SMC Networks, Inc. Other product and company names are trademarks or

registered trademarks of their respective holders.

Warranty and Product Registration

To register SMC products and to review the detailed warranty statement, please refer to

the Support Section of the SMC Website at http://www.smc.com.

i

Compliances and Safety Warnings

FCC - Class A

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that changes or modifications not expressly approved by the party

responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or better

for 10 Mbps connections, Category 5 or better for 100 Mbps connections, Category 5, 5e,

or 6 for 1000 Mbps connections. For fiber optic connections, you may use 50/125 or 62.5/

125 micron multimode fiber or 9/125 micron single-mode fiber.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus as set out in the interference-causing equipment standard entitled

“Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux

appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur:

“Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

ii

CE Mark Declaration of Conformance for EMI and Safety (EEC)

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the

compliance with these Directives, the following standards were applied:

Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this

device.

Attention: Les raccordeurs ne sont pas utilisés pour le système téléphonique!

RFI Emission: • Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity: • Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC power

supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993

(1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

LVD: • EN 60950-1:2001

iii

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

PSE Alarm

本製品に同梱いたしております電源コードセットは、本製品専用です。本電源コード

セットは、本製品以外の製品並びに他の用途でご使用いただくことは出来ません。

製品本体に同梱された電源コードセットを利用し、他製品の電源コードセットを使用し

ないで下さい。

Power Cord Safety

Please read the following safety information carefully before

installing the switch:

WARNING: Installation and removal of the unit must be carried out by qualified personnel

only.

• The unit must be connected to an earthed (grounded) outlet to comply with international

safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without an earth (ground)

connection.

• The appliance coupler (the connector to the unit and not the wall plug) must have a

configuration for mating with an EN 60320/IEC 320 appliance inlet.

• The socket outlet must be near to the unit and easily accessible. You can only remove

power from the unit by disconnecting the power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage) conditions according to

IEC 60950. The conditions are only maintained if the equipment to which it is connected

also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT

†

supplies. If your supplies are of IT type, this unit

must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the

secondary connection point labelled Neutral, connected directly to earth (ground).

†

Impédance à la terre

When using a fiber optic port, never look at the transmit laser while it is

powered on. Also, never look directly at the fiber TX port and fiber cable

ends when they are powered on.

Ne regardez jamais le laser tant qu'il est sous tension. Ne regardez

jamais directement le port TX (Transmission) à fibres optiques et les

embouts de câbles à fibres optiques tant qu'ils sont sous tension.

Niemals ein Übertragungslaser betrachten, während dieses

eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß und auf

die Faserkabelenden schauen, während diese eingeschaltet sind.

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

iv

Important! Before making connections, make sure you have the correct cord set. Check

it (read the label on the cable) against the following:

Veuillez lire à fond l'information de la sécurité suivante avant

d'installer le Switch:

AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un

personnel qualifié.

• Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il

n'y a pas de connexion de mise à la terre (mise à la masse).

• Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de

respecter les normes internationales de sécurité.

• Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit

respecter une configuration qui permet un branchement sur une entrée d’appareil EN

60320/IEC 320.

• La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile.

Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique

au niveau de cette prise.

• L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à

la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il

est raccordé fonctionne dans les mêmes conditions.

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.

The minimum specifications for the flexible cord are:

- No. 18 AWG - not longer than 2 meters, or 16 AWG.

- Type SV or SJ

- 3-conductor

The cord set must have a rated current capacity of at least 10 A

The attachment plug must be an earth-grounding type with NEMA

5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

Denmark The supply plug must comply with Section 107-2-D1, Standard

DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted

with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

Europe The supply plug must comply with CEE7/7 (“SCHUKO”).

The mains cord must be <HAR> or <BASEC> marked and be of type

HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

v

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos

alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une

tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec

un point secondaire de connexion portant l’appellation Neutre et avec raccordement

direct à la terre (masse).

Bitte unbedingt vor dem Einbauen des Switches die folgenden Si-

cherheitsanweisungen durchlesen:

WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal

erfolgen.

• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen

werden.

• Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die

internationalen Sicherheitsnormen erfüllt.

• Der Gerätestecker (der Anschluß an das Gerät, nicht der Wandsteckdosenstecker) muß

einen gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben.

• Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die

Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus

der Netzsteckdose unterbrochen werden.

• Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen

(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben,

wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen

betrieben werden.

Cordon électrique - Il doit être agréé dans le pays d’utilisation

Etats-Unis et

Canada:

Le cordon doit avoir reçu l’homologation des UL et un certificat de la

CSA.

Les spe'cifications minimales pour un cable flexible sont AWG No.

18, ouAWG No. 16 pour un cable de longueur infe'rieure a` 2 me'tres.

- type SV ou SJ

- 3 conducteurs

Le cordon doit être en mesure d’acheminer un courant nominal d’au

moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre

(mise à la masse) et respecter la configuration NEMA 5-15P (15 A,

125 V) ou NEMA 6-15P (15 A, 250 V).

Danemark: La prise mâle d’alimentation doit respecter la section 107-2 D1 de la

norme DK2 1a ou DK2 5a.

Suisse: La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011.

Europe La prise secteur doit être conforme aux normes CEE 7/7 (“SCHUKO”)

LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit

être de type HO3VVF3GO.75 (minimum).

vi

Warnings and Cautionary Messages

Environmental Statement

The manufacturer of this product endeavours to sustain an environmentally-friendly policy

throughout the entire production process. This is achieved though the following means:

• Adherence to national legislation and regulations on environmental production

standards.

• Conservation of operational resources.

• Waste reduction and safe disposal of all harmful un-recyclable by-products.

• Recycling of all reusable waste content.

• Design of products to maximize recyclables at the end of the product’s life span.

• Continual monitoring of safety standards.

End of Product Life Span

This product is manufactured in such a way as to allow for the recovery and disposal of all

included electrical components once the product has reached the end of its life.

Manufacturing Materials

There are no hazardous nor ozone-depleting materials in this product.

Stromkabel

. Dies muss von dem Land, in dem es benutzt wird geprüft werden:

Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen ein-

halten.

Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung)

sein und die Aufschrift <HAR> oder <BASEC> tragen.

Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).

Warning: This product does not contain any serviceable user parts.

Warning: Installation and removal of the unit must be carried out by qualified

personnel only.

Warning: When connecting this device to a power outlet, connect the field ground lead

on the tri-pole power plug to a valid earth ground line to prevent electrical

hazards.

Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers

are compliant with the requirements of a Class 1 Laser Product and are

inherently eye safe in normal operation. However, you should never look

directly at a transmit port when it is powered on.

Caution: Wear an anti-static wrist strap or take other suitable measures to prevent

electrostatic discharge when handling this equipment.

Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this

device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC

standards.

vii

Documentation

All printed documentation for this product uses biodegradable paper that originates from

sustained and managed forests. The inks used in the printing process are non-toxic.

viii

About This Guide

Purpose

This guide details the hardware features of this device, including the physical and

performance-related characteristics, and how to install it.

Audience

The guide is intended for use by network administrators who are responsible for installing

and setting up network equipment; consequently, it assumes a basic working knowledge

of LANs (Local Area Networks).

Conventions

The following conventions are used throughout this guide to show information:

Note: Emphasizes important information or calls your attention to related features or

instructions.

Caution: Alerts you to a potential hazard that could cause loss of data, or damage the

system or equipment.

Warning: Alerts you to a potential hazard that could cause personal injury.

Related Publication

The following publication gives specific information on how to operate and use the

management functions of the switch:

The Management Guide

Also, as part of the switch’s software, there is an online web-based help that describes all

management related features.s

Revision History

This section summarizes the changes in each revision of this guide.

August 2009 Revision

This is the first revision of this guide.

ix

Contents

Chapter 1: Introduction 1-1

Overview 1-1

Switch Architecture 1-2

Network Management Options 1-2

Description of Hardware 1-3

10/100/1000BASE-T Ports 1-3

SFP Slots 1-3

10 Gigabit Ethernet Module Slots 1-3

Stacking Ports 1-3

Port and System Status LEDs 1-3

Optional Redundant Power Supply 1-5

Power Supply Sockets 1-5

Optional Media Extender Modules 1-6

Extender Module LEDs 1-6

Features and Benefits 1-7

Connectivity 1-7

Expandability 1-7

Performance 1-7

Management 1-7

Chapter 2: Network Planning 2-1

Introduction to Switching 2-1

Application Examples 2-2

Collapsed Backbone 2-2

Network Aggregation Plan 2-3

Remote Connections with Fiber Cable 2-4

Making VLAN Connections 2-5

Using Layer 3 Routing 2-6

Application Notes 2-7

Chapter 3: Installing the Switch 3-1

Selecting a Site 3-1

Ethernet Cabling 3-1

Equipment Checklist 3-2

Package Contents 3-2

Optional Rack-Mounting Equipment 3-2

Mounting 3-3

Rack Mounting 3-3

x

Contents

Desktop or Shelf Mounting 3-4

Installing an Optional Module into the Switch 3-5

Installing an Optional SFP Transceiver 3-6

Connecting Switches in a Stack 3-7

Stacking Topologies 3-8

Connecting to a Power Source 3-8

Connecting to the Console Port 3-9

Wiring Map for Serial Cable 3-9

Chapter 4: Making Network Connections 4-1

Connecting Network Devices 4-1

Twisted-Pair Devices 4-1

Cabling Guidelines 4-1

Connecting to PCs, Servers, Hubs and Switches 4-2

Network Wiring Connections 4-2

Fiber Optic SFP Devices 4-3

10 Gbps Fiber Optic Connections 4-4

Connectivity Rules 4-6

1000BASE-T Cable Requirements 4-6

10 Gbps Ethernet Collision Domain 4-6

1000 Mbps Gigabit Ethernet Collision Domain 4-7

100 Mbps Fast Ethernet Collision Domain 4-7

10 Mbps Ethernet Collision Domain 4-7

Cable Labeling and Connection Records 4-8

Appendix A: Troubleshooting A-1

Diagnosing Switch Indicators A-1

Diagnosing Power Problems with the LEDs A-1

Power and Cooling Problems A-2

Installation A-2

In-Band Access A-2

Stack Troubleshooting A-3

Appendix B: Cables B-1

Twisted-Pair Cable and Pin Assignments B-1

10BASE-T/100BASE-TX Pin Assignments B-1

Straight-Through Wiring B-2

Crossover Wiring B-2

1000BASE-T Pin Assignments B-3

Cable Testing for Existing Category 5 Cable B-4

Adjusting Existing Category 5 Cabling to Run 1000BASE-T B-4

Fiber Standards B-4

xi

Contents

Appendix C: Specifications C-1

Physical Characteristics C-1

Switch Features C-3

Management Features C-3

Standards C-3

Compliances C-4

Extender Modules C-4

10GBASE Extender Module (XFP) C-4

Glossary

Index

xii

Tables

Table 1-1 Port Status LEDs 1-4

Table 1-2 System Status LEDs 1-4

Table 1-3 Supported XFP Transceivers 1-6

Table 1-4 Module LEDs 1-6

Table 3-1 Serial Cable Wiring 3-9

Table 4-1 Maximum 10GBASE-SR 10 Gigabit Ethernet Cable Length 4-6

Table 4-2 Maximum 10GBASE-LR 10 Gigabit Ethernet Cable Length 4-6

Table 4-3 Maximum 10GBASE-ER 10 Gigabit Ethernet Cable Length 4-6

Table 4-4 Maximum 1000BASE-T Gigabit Ethernet Cable Length 4-7

Table 4-5 Maximum 1000BASE-SX Gigabit Ethernet Cable Length 4-7

Table 4-6 Maximum 1000BASE-LX Gigabit Ethernet Cable Length 4-7

Table 4-7 Maximum 1000BASE-LH Gigabit Ethernet Cable Length 4-7

Table 4-8 Maximum Fast Ethernet Cable Length 4-7

Table 4-9 Maximum Ethernet Cable Length 4-7

Table A-1 Troubleshooting Chart A-1

Table A-2 Power/RPS LEDs A-1

Table B-1 10/100BASE-TX MDI and MDI-X Port Pinouts B-2

Table B-2 1000BASE-T MDI and MDI-X Port Pinouts B-3

Table B-3 Fiber Standards B-4

xiii

Figures

Figure 1-1 Front Panels 1-1

Figure 1-2 Rear Panel 1-2

Figure 1-3 Port LEDs 1-4

Figure 1-4 System LEDs 1-4

Figure 1-5 Power Supply Sockets 1-5

Figure 1-6 Single-Port 10GBASE Module (XFP) 1-6

Figure 2-1 Collapsed Backbone 2-2

Figure 2-2 Network Aggregation Plan 2-3

Figure 2-3 Remote Connections with Fiber Cable 2-4

Figure 2-4 Making VLAN Connections 2-5

Figure 2-5 IP Routing for Unicast Traffic 2-6

Figure 3-1 RJ-45 Connections 3-2

Figure 3-2 Attaching the Brackets 3-3

Figure 3-3 Installing the Switch in a Rack 3-4

Figure 3-4 Attaching the Adhesive Feet 3-4

Figure 3-5 Installing an Optional Module 3-5

Figure 3-6 Inserting an SFP Transceiver into a Slot 3-6

Figure 3-7 Making Stacking Connections 3-7

Figure 3-8 Power Socket 3-8

Figure 3-9 Serial Port (RJ-45) Pin-Out 3-9

Figure 4-1 Making Twisted-Pair Connections 4-2

Figure 4-2 Network Wiring Connections 4-3

Figure 4-3 Making Connections to SFP Transceivers 4-4

Figure 4-4 Connecting to an XFP Transceiver 4-5

Figure B-1 RJ-45 Connector Pin Numbers B-1

Figure B-2 Straight-through Wiring B-2

Figure B-3 Crossover Wiring B-3

xiv

Figures

1-1

Chapter 1: Introduction

Overview

The SMC8926EM and SMC8950EM are intelligent multilayer switches (Layer 2, 3)

with 24/48 10/100/1000BASE-T ports, four of which are combination ports

*

that are

shared with four SFP transceiver slots (see Figure 1-1, Ports 21-24/45-48). The rear

panel provides two slots for single-port 10 Gigabit Ethernet hot-swappable

expansion modules, and two stacking ports. Units can be stacked up to eight high

through the built-in stacking ports that provide a 50 Gbps stack backplane.

The switches include an SNMP-based management agent embedded on the main

board, which supports both in-band and out-of-band access for managing the stack.

These switches can easily tame your network with full support for Spanning Tree

Protocol, Multicast Switching, Virtual LANs, and IP routing. It brings order to poorly

performing networks by segregating them into separate broadcast domains with

IEEE 802.1Q compliant VLANs, empowers multimedia applications with multicast

switching and CoS services, and eliminates conventional router bottlenecks.

These switches can be used to augment or completely replace slow legacy routers,

off-loading local IP traffic to release valuable resources for non-IP routing or WAN

access. With wire-speed performance for Layer 2 and Layer 3, these switches can

significantly improve the throughput between IP segments or VLANs.

Figure 1-1 Front Panels

* If an SFP transceiver is plugged in, the corresponding RJ-45 port is disabled for ports 21-24

on SMC8926EM or ports 45-48 on SMC8950EM.

Serial Console Port

10/100/1000 Mbps RJ-45 Ports

SFP Slots

Port Status LEDs

System Status LEDs

Stack ID

SMC8950EM

SMC8926EM

1

2

3

4

5

6

7

8910

11

12

13

14

15

16

17

18 19 20

21 22

23

24

21 22 23 24

Stack

Master

Power

Module

Diag

Stack

Link

Stack ID

RPU

ES4626H

Master

Select

Console

Stack ID

Stack

Master

21 22 23 24

Introduction

1-2

1

Figure 1-2 Rear Panel

Switch Architecture

These Gigabit Ethernet switches employ a wire-speed, non-blocking switching

fabric. This permits simultaneous wire-speed transport of multiple packets at low

latency on all ports. The switches also feature full-duplex capability on all ports,

which effectively doubles the bandwidth of each connection.

For communications between different VLANs, these switches use IP routing. For

communications within the same VLAN, they use store-and-forward switching to

ensure maximum data integrity. With store-and-forward switching, the entire packet

must be received into a buffer and checked for validity before being forwarded. This

prevents errors from being propagated throughout the network.

These switches include built-in stacking ports that enable up to eight units to be

connected together through a 48 Gbps stack backplane. The switch stack can be

managed from a master unit using a single IP address.

These switches also include two slots on the rear panel for slide-in single-port

10GBASE modules with XFP transceivers.

Network Management Options

These switches contain a comprehensive array of LEDs for “at-a-glance” monitoring

of network and port status. They also include a management agent that allows you

to configure or monitor the switch using its embedded management software, or via

SNMP applications. To manage each switch, you can make a direct connection to

the console port (out-of-band), or you can manage the switches through a network

connection (in-band) using Telnet, the on-board web agent, or SNMP-based network

management software.

For a detailed description of both switches’ advanced features, refer to the Gigabit

Ethernet Switch Management Guide.

Stacking Ports

Power Socket

Redundant Power Socket

ModuleSlots

Page is loading ...

SMC Networks SMC8950EM User manual

This manual is also suitable for

SMC Networks SMC8950EM User manual

Related papers

Other documents