Atdec TH-TVCB Installation guide

Category
Multimedia carts & stands
Type
Installation guide
TH-TVCB
Component Checklist
Mobile TV Cart
HARDWARE
Column
Frame
ShelfMounting Bracket
Shelf Mounting
Screw
M8x16 Screw
(x4)
M8 Screw (x6)
M8 Spring
Washer (x6)
! IMPORTANT - Install TV Cart as per installation instruction.
! This product supports a maximum load of 50kg (110lbs.).
! This product supports VESA mounting hole configurations: From 200 x 200mm to 800 x 600mm.
! The manufacturer accepts no responsibility for incorrect installation.
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received against the component checklist and hardware above.
Step 2. Assemble Base Step 3. Fasten Column to Base
M8 Screws
Spring Washer
OR
Tilt Mechanism
Extension Washer (x4)
Extension Bracket (x4)
Caster (x4)
Top Cap (x4)
Shelf Mounting Plate
Caster
Supplied
Spanner
Frame
UNLOCKED
LOCKED
Supplied Allen Key
Column
Base
Step 4A.
Attach Tilt Mechanism to Display
Step 4B.
Insert Tilt Mechanism to Column
TOP
Spanner (x2)
Allen Key
M8x10 Screw (x8)
M5 Washer (x6)
M8 Washer (x10)
1/4” Washer (x6)
Spacer (x6)
Display Mounting
Screws (x6 each)
M4x16/35mm
M5x16/35mm
M6x16/35mm
M8x16/35mm
Tools Required:
Phillips head screw driver
Display Mounting
Screw
Washer
Tilt Mechanism
Spacer
(optional, use
only for recessed
mounting holes.)
INSERT
Supplied Allen
Key
For a VESA Hole Configuration of 200x200mm ONLY go to Step 4 and skip Step 5 & 6.
For a VESA Hole Configuration of over 200x200mm skip Step 4 and go to Step 5.
Installation Instructions
Step 5A. Insert Tilt Mechanism to Column Step 5B. Attach Mounting Bracket to Display
2 ROTATE
1 INSERT
INSERT
Display Mounting Screw
Washer
Mounting Bracket
M8x10mm Screw
M8 Washer
Extension Washer
Extension Bracket
Supplied Allen
Key
Step 8. Secure Display
Top of Display
Insert two M8x16mm screws
with M8 washers. Use
the supplied Allen Key to
tighten.
±90°
You can adjust
the display either
to Landscape or
portrait view.
Spacer
(optional, use only for
recessed mounting holes.)
M8x16 Screw
Step 6. Insert two M8x16 Screws Step 7. Attach Mounting Bracket to Tilt Mechanism
Leave 3-5mm gap
Top of Display
Step 9. Set to Landscape or Portrait
Top of Display
Top of Display
The mounting bracket supports 250 x 250mm up to 600 x 400mm VESA hole configurations.
To accomodate up to 800 x 600mm attach the supplied extension bracket as shown.
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 31.10.12 ©
Step 10. Tilt Adjustment Step 11. Adjust Height
+10°
FORWARD TILT
NOTE: Use the two
supplied spanner to
adjust tension and
tilt if necessary.
Height
Range
1120mm
1820mm
Option 1
Option 2
Top Cap
Shelf
Mounting
Options
Shelf Mounting Screw
Shelf Mounting Plate
Shelf
Step 12. Cable Management Step 13. Attach Shelf
HOLD
HOLD
Tighten
Loosen
Loosen
Tighten
Supplied Allen key
  • Page 1 1
  • Page 2 2
  • Page 3 3

Atdec TH-TVCB Installation guide

Category
Multimedia carts & stands
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI