2. Hitachi
  3. GP 2

Hitachi GP 2 User manual

  • Hello! I am an AI chatbot trained to assist you with the Hitachi GP 2 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Sleipner Motor A/S Sleipner Motor A/S
User manual
Sidepower
Tunnel Cut-out Tool
Art. No. 6 8870 / 6 8871
Ver.1 - 2007
Sleipner Motor A/S Sleipner Motor A/S
Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diamete
r
Sleipner Motor A/S Sleipner Motor A/S
- Assemble the cut-out tool, and adjust it to the right tunnel
diameter. After finger-tightening the two threaded handles,
tighten the adjustment-screw to get the right A-distance
Thruster Position at cut-out tool Distance A
SP35S 125 Min. 74mm
Min. 2
15
/
16
”
SP55S, SP75T, SP95T,
SP100HYD
185 Min. 105mm
Min. 4
1
/
8
”
SP125T, SP155TC,
SP200TC, SP200HYD
250 Min. 140mm
Min. 5 ½”
SP220TC, SP285TC,
SP300HYD
300 Min. 167mm
Min. 6
9
/
16
”
SP550TC HYD 386 Min. 213mm
Min. 8
3
/
8
”
Use the table for selection of position and adjustment of the cut-out tool.
Adjustment-screw at Ø125mm tunnel
Adjustment-screw at Ø386mm tunnel
Sleipner Motor A/S Sleipner Motor A/S
- Assemble the cut-out tool, and adjust it to the right tunnel
diameter. After finger-tightening the two threaded handles,
tighten the adjustment-screw to get the right A-distance
Thruster Position at cut-out tool Distance A
SP35S 125 Min. 74mm
Min. 2
15
/
16
”
SP55S, SP75T, SP95T,
SP100HYD
185 Min. 105mm
Min. 4
1
/
8
”
SP125T, SP155TC,
SP200TC, SP200HYD
250 Min. 140mm
Min. 5 ½”
SP220TC, SP285TC,
SP300HYD
300 Min. 167mm
Min. 6
9
/
16
”
SP550TC HYD 386 Min. 213mm
Min. 8
3
/
8
”
Use the table for selection of position and adjustment of the cut-out tool.
Adjustment-screw at Ø125mm tunnel
Adjustment-screw at Ø386mm tunnel
Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diamete
r
Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diamete
r
Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diamete
r
/