Pelco KSC-3000U Keyboard Installation guide

1

USBSYSTEMCONTROLLER

USERMANUAL

Rev.1.00D_131010En

C1368M-B | 12/17/18

KEVIS.INC

2



Restriction

KevisInc.ownsthecopyrightstothismanual.

Nopartofthismanualmaybereproducedortransmittedinanyformorbyanymeanswithoutthe

writtenconsentofKevisInc.

Disclaimer

TheaccuracyoftheinformationcontainedinthisdocumenthasbeenverifiedbyKevisInc.Youare

fullyresponsiblefortheresultsobtainedfromtheuseofthismanual.Theinformationinthis

documentissubjecttochangewithoutnotice.

Warranty

Ourwarrantycoversmechanic alandelectricalfailuresthatoccurwithnormaluse.

Thewarrantyisvalidforoneyear.Thefollowingconditionsareexcludedfromthewarranty.



 Whensystemfailureoccursduetoimpropermanipulationormodification.

 Whentheproductisdamagedbyfloodingorfire.

 Whenproductmalfunctionoccurredduetowearoftheparts.



FeaturesandDesignoftheproductissubjecttochangewithoutnoticeduetoimprovingthe

performanceoftheproduct.



3



USEPRECAUATION

Thank you for choosing our product. Please read this document carefully before use.

To prevent risk or damage to the property you must follow these instructions.



Warning

 Do not exceed the standard capacity (Voltage/Current) of a multi-plug or

power outlet extension when using it for the product.

There is a danger of electric shock or fire hazard.

 Do not place any container filled with water or chemicals over or near the

product.

If water or chemicals enter the computer, this may cause fire or electric

shock.

 Do not place heavy objects or step on the power cord or AC adapter to

avoid damage.

If the cord is damaged, there is a danger of electric shock or fire.

 Do not install the product on a slant or a place prone to vibrations.

This increases the risk that a malfunction or damage to the product will occur.

If the product falls there is a risk of injury.

 If the system makes a noise, disconnect the power cord from the wall

outlet and contact the place of purchase or Kevis inc.

There is a danger of electric shock or fire hazard.



Warning‐Violationoftheinstructionsmaycausedeathorinjury

Caution– Violationoftheinstructionsmaycausepersonalinjuryorpropertydamage.

4



Caution

 Avoid installation where strong magnetic, electromagnetic fields or close

to wireless device.

 Avoid installation where strong shock or vibration may occur.

 Do not use in too heavy dust, smoke or humid environments.

 Do not put the product in direct sunlight.

 Always keep the operating temperature and humidity.

 Do not place conductive material (such as screw driver, coin, etc…) nor

vessel full of water.

 Do not place a heavy object over the product.

 Unplug the power during thunder storm, lightning.

 Make sure to use grounded power outlet.



5



Contents

1. PackageContents ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6

2. ProductFeatures ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 7

3. Description ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 8

4. Installation&Connection ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 11

5. Setting ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13

 1) PTZSetup ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13

 2) DVRSetup ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 14

 3) MainMenuSetup ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 15

 4) Joystick Calibration ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 18

 5) USBHotkeySetup ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 19

 6) HIDJoystickSetup ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 20



7) StopwatchSetup ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 21

 8) ButtonTest ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 21

 9) UploadSettingValue ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 21

 10) SystemInformation ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 23

 11) JoystickTest ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 23

 12) LCDTest ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 24

 13) ProtocolAnalyzer(Option) ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 24

 14) ProtocolCodeAnalyzer(Option) ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 25

6. Operation ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 25

 1) LCDScreen ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 25

 2) Password ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙

 3) PTZMode ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 26

 4) DVRMode ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 27

 5) HIDMode ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 27

 6) RestoreFactor ySettings ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 28

 7) InterlockingSystemController ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 28

7. Drawing ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 29

8. Specification ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 30

  



6



1.PackageContents

ChecktheProductBoxforthefollowingitems:



KSCSystemController 12VAdapter



UserManual AtoBUSBCable



PackingList



1. KSC‐3000USystemCont roller ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙

1pcs

2. DC12VPowerAdapter ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙

1pcs

3. UserManual ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙

1pcs

4. AtoBUSBCable ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙

1pcs



7



2.ProductFeatures

1) TwoRS‐485Ports

RS‐485PortsareusedforMasterandSubcommunications.

EachindividualaddressoftheMasterPortcanbesetwithdifferentprotocol.



2) Multi‐Protocols

Varietyprotocolsarebuilt‐inforeaseofremotecontrol.



3) UnifiedProtocol

VariousdeviceslikeDVR,PTZ,and

Domecanbecontrolledsimultaneously.



4) HIDUSBMOUSE&KEYBOARD&GAMEJOYSTICK

ThesystemcontrollercanbeusedasaMouse,KeyboardorJoystickforPCorNVRwithout

externaldriverinstallation.

AlphanumericcharactersinputaresupportedthroughnumerickeypadinKeyboardMode.

Mousescrollandsensitivitysetting

issupportedinMouseMode.

*ExternalpowerisnotrequiredwhenUSBisconnected.



5) Hot‐Key

AllhotkeysforthePCapplicationscanbesupportedwithcontroller’sshortcutkeysinHotkey

Mode.Createandmodifyshortcutkeysusingthesystemcontroller.



6) ProgrammableHIDJOYSTICKbuttons

All

buttonsonthesystemcontrollercanbeusedasthejoystickbuttonsandprogrammable

exceptthefollowings.

 ESC(whenexitingfromHIDmode)

 USBHID(whenchangingfrom3differentHIDModes)



7) Multiplecontrollerssupporting

Max.9controllerscanbeconnectedandusedsimultaneouslythroughPort2



8) Easeofoperation

Built‐in3‐Axisproportionaljoystick,LCD,Rubberbuttons,JogShuttleforeaseofoperation



9) ExtraFeatures

Self‐diagnosticmode,StopWatch,protocolanalysis,andavarietyofadd‐onscanbeutilized

foron‐sitefacilityinspection.

8



3.Description

TOPView



RearView



9



1) LCD(Display)

Showsnumberentered,systemstatus,functionstatusandgeneralstatu s.



2) ESC

Usedtoescapefromthecurrentmodeorcancelthecurrentselection.



3) SET

UsedtosetPTZorDVRfeaturevalueswiththenumerickeys.



4) PTZ/DVR

UsedtochangemodetoPTZorDVR.



5) CAM/CH

UsedtoselectaPTZcameraoraDVRchannelwiththenumerickeys.



6) PRESET/REW

PRESET(PTZMode):UsedtosaveorcallPTZpresets.

REW(DVRMode):Usedtorewindplaybackvideoordata.



7) SCAN/F.F

SCAN(PTZMode):UsedtocallaPTZscans.

F.F(DVRMode):Usedtofast‐forwardplaybackvideoordata.



8) PATTERN/FRZ

PATTERN(PTZMode):UsedtocallPTZpatterns.

FRZ(DVRMode):Usedtofreezethecamerascreensonliveview.



9) TOUR/MODE

TOUR(PTZMode):UsedtocallPTZtours.

MODE(DVRMode):Usedtochangedisplaymode.



10) AUTO/SEQ

AUTO(PTZMode):UsedtocallPTZautopan.

SEQ(DVRMode):Usedtoturnon/offdisplaysequencefeature.



11) USBHID

ChangeHIDmodeinthefollowingorder‘Mouse‐>Joystick‐>Keyboard’.

10



12) AUXON/ALARM

AUXON(PTZMode):Usedtoturnonauxiliaryfeature.

ALARM(DVRMode):Usedtoturnon/offalarmfeature.

13) AUXOFF/AUDIO

AUXOFF(PTZMode):Usedtoturnoffauxiliaryfeature.

AUDIO(DVRMode):Usedtoenableordisableaudio.



14) REC/1st

REC(DVRMode):Usedto start/stopforcerecording.

1st:Inputfirstcharacteronnumerickeywhenenteringtext.



15) PLAY /2nd

PLAY(DVRMode):Usedtoplaybackvideoordata.

2nd:Inputsecondcharacteronnumerickeywhenenteringtext.



16) STOP/3rd

STOP(DVRMode):Usedtostopplaybackvideoordata.

3rd:Inputthirdcharacteronnumerickeywhenenteringtext.



17) SEARCH/CAPSLOCK

SEARCH(DVRMode):Usedtogotosearchmode.

CAPSLOCK:CapsLockON/OFFwhenenteringtext.



18) 0~9

UsedtoenterthenumbersforPTZ/DVRselection,setupmenuopeningorusedforentering

alphanumericcharacters.



19) CLR

UsedtocleartheinputtedvalueorusedasbackspacekeyinHIDKeyboardMode



20) ENT

Usedtoenterorselectvalues



21)JOYSTICK

UsedtoprecisecontrolofPan/Tilt/ZoomandmoveDVR/Keyboard‐menucursor.

InHIDMode,itisusedasamousecursorandkeyboard‐hotkeycombinations.



22) LENSCONTROL

Usedforcameralenscontrol.

Irisbuttons(Close/M‐L,Open/M‐R)arealsousedasmousebuttonsinHIDmousemode.

11



23) JOG/SHUTTLE

UsedforeasycontroloftheDVRplaybackinDVRmode.

LenscontrolisalsoavailablebasedontheMenusetting.

24) LEDINDICATOR

Showsthecommunicationandpowerstatus.



25) DCJACK

UsedforDC12Vinput



26) RS‐485CONNECTOR

UsedforRS‐485connection



27) PROGRAMCONNECTOR

Usedtoupdateproductfirmware.(Factoryuseonly)



28) USBCONNECTOR

UsedforPCorDVRconnection



4.Installation&Connection



12



HalfDuplexMode





FullDuplex Mode



13



5.Setting



Movethejoystickupordowntomovethesettingmenus.

Tochangethesettingvalues,movethejoystickleftorright.



1) PTZSetup



Inthecontrolmode,Press “1”and hold“Set”buttonfor

approximately2second.

↓



EnterthePTZIDbyusingJoystick(Left/Right)orNumeric

Keypad.

Ex)PTZ10=“1”,”0”+“Enter”

 Movethejoystickdown forthenextsettingmenu.



SelectaPTZProtocolbyusingJoystick(Left/Right).



 Movethejoystickdown forthenextsettingmenu.



SelectaBaudrateforthePTZcommunication.

 Movethejoystickdown forthenextsettingmenu.



SelectaParitybit.

 Movethejoystickdown forthenextsettingmenu.



Whenfinished,Press“Enter”tosaveandexit.



Youmaypress“ESC”anytimetoexitfromthePTZsetupmenu.

PELCO‐D9.6K

PTZ:001

PTZSETUP[001]

1.PTZID:10

PTZSETUP[001]

2.Protocol:PEL‐D

PTZSETUP[001]

3.Baudrate:9.6K

PTZSETUP[001]

4.Parity:None

PTZSETUP[001]

5.Exit

14



2) DVRSetup



Inthecontrolmode,Pres s“

”andhold“

Set

”buttonfor

approximately2second.

↓





Enterthe

DVRID

byusingJoystick(Left/Right)orNumeric

Keypad.

Ex)DVR35=“3”,”5”+“Enter”



Movethejoystickdownforthenextsettingmenu.



Selecta

DVRProtocol

byusingJoystick(Left/Right).



Movethejoystickdownforthenextsettingmenu.



Selecta

DVRProtocol

byusingJoystick(Left/Right).



Movethejoystickdownforthenextsettingmenu.



Selecta

Baudrate

fortheDVRcommunication.



Movethejoystickdownforthenextsettingmenu.



Whenfinished,Press“

Enter

”to

save

and

exit

.



Youmaypress“

ESC

”anytimeto

exit

fromtheDVRsetupmenu.





SAMSUNG‐E9.6K

DVR:001

DVRSETUP[001]

1.DVRID:001

DVRSETUP[001]

1.DVRID:001

DVRSETUP[001]

2.Protocol:PEL‐D

DVRSETUP[001]

3.Baudrate:9.6K

DVRSETUP[001]

4.Exit

15



3) MainMenuSetup





MainmenusetupisrelatedwithSystemControl.



Inthecontrolmode,Pres s“

”andhold“

Set

”buttonfor

approximately2second.

↓



Ifthesystemispasswordprotected,

Defaultpassword

is

“

123456

”Thepasswordmaybechangedbyuser.

Pleaserefertothepasswordsetmenudownbelow.



Select

KeyboardID

or

Address

.

- Availableoptions:Standalone,Master,Sub2~Sub9

Note:

Whenusingproductsfromothercompanies,selectstandalone

option.



Movethejoystickdownforthenextsettingmenu.



Selecta

RS‐485

communicationtypefor

Port1

.

Availableoptions:Half,FullDuplex





Movethejoystickdownforthenextsettingmenu.



Selecta

RS‐485

communicationtypefor

Port2

.

Availableoptions:Half,FullDuplex





Movethejoystickdownforthenextsettingmenu.



Selectthe

brightness

ofthe

LCDbacklight

.

Availableoptions:Min,L‐1~L‐6,Max





Movethejoystickdownforthenextsettingmenu.



Selecta

waittime

optiontogointo

sleepmode

.

Availableoptions:Off,1Min,3Min,5Min,10Min,30Min





Movethejoystickdownforthenextsettingmenu.

PELCO‐D9.6K

PTZ:001

MAINMENU

1.KBDID:S‐Alone

MAINMENU

2.Port1485:Half

MAINMENU

3.Port2485:Half

MAINMENU

4.Backlight:L‐4

MAINMENU

5.Sleep:5Min

16



Selectto

turnOn/Off

the

buttonsound

.

Availableoptions:Off,On





Movethejoystickdownforthenextsettingmenu.



Selectthe

commandtransmissioncycletime

forJoystick.

Availableoptions:40,50,100,150,200,250,300ms



Note:

Iftransmissioncycleisshort,theresponsespeedisfast,butPTZ

mayhaveaproblemtocommandprocessing.



Movethejoystickdownforthenextsettingmenu.



Selectthe

lenscontrolaction

forJog/ShuttleinPTZMode.

- Availableoptions:Off,J‐Z/S‐Z,J‐F/S‐F,J‐Z/S‐F,J‐F/S‐Z

Note:

J(Jog)/S(Shuttle)/Z(Zoom)/F(Focus)

Exampleofuse:Telephotolenscontrol.



Movethejoystickdownforthenextsettingmenu.



Selectthe

mousesensitivity.



Availableoptions:Min,L‐1~L‐4,Max





Movethejoystickdownforthenextsettingmenu.



Selectthetimefor

commandre‐transmissioncycle.



- Availableoptions:Off,1~5Sec

Warning:

SupportedPTZuseonly.



Movethejoystickdownforthenextsettingmenu.



Tochangethecurrentpassword,press"

Enter

"orMovethe

joysticktotheright



Otherwise,movethejoystickdownforthenextsetupmenu.

→ ↓

MAINMENU

6.Buzzer:On

MAINMENU

7.Joy.Dly:50ms

MAINMENU

8.Jog/St:J‐F,S‐F

MAINMENU

9.Mouse:L‐3

MAINMENU

10.Command:Off

MAINMENU

11.PWSet:Set

17



Enterthe

newpassword

.



↓

Re‐enterthe

newpassword

toconfirm.

Then,press"

Enter

"to

save

orPress"

ESC

"to

exitwithoutsaving

.



Movethejoystickdownforthenextsettingmenu.



Selectthe

passwordprotectioncoverage



- Availableoptions:Off,Menu,M+DVR,M+PTZ,All

Note:

M+DVR=Menu&DVR

M+PTZ=Menu&PTZ



Movethejoystickdownforthenextsettingmenu.



Selectthe

passwordlocktime

.

- Availableoptions:Off,10Sec,30Sec,1,3,5,10,30Min

Note:

PasswordlockisappliedonMenuSetupimmediately.

Otherwise,Passwordlockisapplied afterPasswordLockTime.





Toescapefromthepasswordlockmode,

press"Clear",thenenterpassword.



Movethejoystickdownforthenextsettingmenu.



Thesystemcontrollerwillshowits

firmwareversion

onthe

screen.



Movethejoystickdownforthenextsettingmenu.



Toloadthe

factorydefaultsetting

,press“

ENT

”ormovethe

joysticktotheright.



Otherwise,movethejoystickdownforthenextsetupmenu.



Movethejoystickdownforthenextsettingmenu.

InputPassword

[]

ConfirmPassword

[]

MAINMENU

12.PWRule:Off

MAINMENU

13.PWTime:Off

MAINMENU

14.Ver:xx.x.x

MAINMENU

15.Factory:Set

18



Press“

ENT

”to

exit

fromtheMainMenuSetup,otherwisemove

thejoystickup/downforthemainmenusettingagain.





4) JoystickCalibration



Inthecontrolmode,Pres s“

”andhold“

Set

”buttonfor

approximately2second.



Warning:

IncorrectsettingscancausemalfunctionofJoystick.

↓



Tosetthe

centerpositionofthejoystick

,

waitfor30seconds

orpress"

Enter

"withouttouchingthe

joystick.

↓



Movethe

joystickup

tothemaximumpositionandhold,then

press“

ENT

”button.

↓



Movethe

joystickdown

tothemaximumpositionandhold,

thenpress“

ENT

”button.

↓



Movethe

joystickleft

tothemaximumpositionandhold,then

press“

ENT

”button.

↓



MAINMENU

16.Exit

PELCO‐D9.6K

PTZ:001

JOYSTICKCAL.

1.PTZOffset:30

JOYSTICKCAL.

2.TiltUp:1020

JOYSTICKCAL.

3.TiltDown:0000

JOYSTICKCAL.

4.PanLeft:1020

19



Movethe

joystickright

tothemaximumpositionandhold,then

press“

ENT

”button.

↓



Turnthe

joystickheadcounterclockwise

tothemaximum

positionandhold,thenpress“

ENT

”button.

↓



Turnthe

joystickheadclockwise

tothemaximumpositionand

hold,thenpress“

ENT

”button.

↓





Select“

Yes

”to

save

thecalibrationdataandexitfromthemenu,

orselect“

”to

exitwithoutsaving

.



5) USBHotkeysetup





AllcontrollerbuttonsareprogrammableasthehotkeysforHIDUSBHotkeyModeexcept

“ESC”and“USBHID”



Inthecontrolmode,Pres s“

”andhold“

Set

”buttonfor

approximately2second.



↓



Select

abuttonofthesystemcontroller

tomakeahotkeywith

thejoystickUp/Down,andpress“

ENT

”

↓



JOYSTICKCAL.

5.PanRight:0000

JOYSTICKCAL.

6.ZoomWide:0000

JOYSTICKCAL.

7.ZoomTele:1020

JOYSTICKCAL.

8.Save:No

PELCO‐D9.6K

PTZ:001

HOTKEYSET

1.Set:None+L

20



Selectthe

firstcombinationkey

forthehotkey,whenfirst

combinationofahotkeyisflashing.

- Availableoptions:None,Ctrl,Alt,Shift,CtlAl(Ctrl+Alt),ShAlt

(Shift+Alt),ShCtl(Shift+Ctrl),SCtAl(Shift+Ctrl+Alt)

Then,press“

ENT

”toselectsecondcombinationkey.

↓



Selecta

secondcombinationkey

forthehotkey,whensecond

hotkeycombinationisflashing.

- Availableoptions:A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,

R,S,T,U,V,W,X,Y,Z,1,2,3,4,5,6,7,8,9,Enter,Backspace,

Tap,F1,F2,F3,F4,F5,F6,F7,F8,F9,F10,

F11,F12,Insert,

Delete,Home,Pageup,PageDown,End,Space,Esc,+,‐,~,

[,],|,,,.?

Whendone,press“

ENT

” tosaveandexit.



6) HIDJoysticksetup





AllcontrollerbuttonsareprogrammableastheJoystickbuttonsforHIDUSBJoystick

Modeexcept“ESC”and“USBHID”



Inthecontrolmode,Pres s“

”andhold“

Set

”buttonfor

approximately2second.

↓



Select

acontrollerbutton

toassignajoystickbuttonnumber

withthejoystickUp/Down.

↓



Selecta

joystickbuttonnumber

withthejoystickLeft/Right.

Note:



Supportsupto36joystickbuttons.



Jog/ShuttleandThrottlecanbeusedasajoystickbutton.





HOTKEYSET

1.Set:None+L

HOTKEYSET

1.Set:None+L

PELCO‐D9.6K

PTZ:001

HIDJOYSTICK

1.Set:10

HIDJOYSTICK

1.Set:10

Page is loading ...

Pelco KSC-3000U Keyboard Installation guide

Related papers

Other documents