Titan LX-75 Airless Spray Gun User manual

Important Safety Instructions

Read all safety information before operating the

equipment. Save these instructions.

Indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

To reduce the risks of re or explosion, electrical shock and the

injury to persons, read and understand all instructions included in

this manual. Be familiar with the controls and proper usage of the

equipment.

WARNING: EXPLOSION OR FIRE

Solvent and paint fumes can explode or ignite. Property damage and/

or severe injury can occur.

PREVENTION:

 • Donotsprayammableorcombustiblematerialsnearanopename,

pilotlightsorsourcesofignitionsuchashotobjects,cigarettes,motors,

electrical equipment and electrical appliances. Avoid creating sparks from

connecting and disconnecting power cords.

 • Forunitsintendedforusewithonlywater-basedormineralspirit-type

materialswithaminimumashpointof38ºC(100ºF)—Donotsprayor

cleanwithliquidshavingaashpointoflessthan38ºC(100ºF).Flashpoint

isthetemperatureatwhichauidcanproduceenoughvaportoignite.

 • Useextremecautionwhenusingmaterialswithaashpointbelow100ºF

(38ºC).Refer to your pump manual to determine if these materials can

be sprayed.

 • Paintorsolventowingthroughtheequipmentisabletoresultinstatic

electricity. Static electricity creates a risk of re or explosion in the presence

ofpaintorsolventfumes.Allpartsofthespraysystem,includingthe

pump,hoseassembly,spraygunandobjectsinandaroundthesprayarea

shallbeproperlygroundedtoprotectagainststaticdischargeandsparks.

Useonlyconductiveorgroundedhigh-pressureairlesspaintsprayerhoses

speciedbythemanufacturer.

 • Verifythatallcontainersandcollectionsystemsaregroundedtoprevent

static discharge.

 • Connecttoagroundedoutletandusegroundedextensioncords(electric

modelsonly).Donotusea3to2adapter.

 • Donotuseapaintorsolventcontaininghalogenatedhydrocarbons.Such

aschlorine,bleachmildewcide,methylenechlorideandtrichloroethane.

Theyarenotcompatiblewithaluminum.Contactthecoatingsupplier

aboutcompatibilityofmaterialwithaluminum.

 • Keepsprayareawellventilated.Keepagoodsupplyoffreshair

moving through the area to keep the air within the spray area free from

accumulationofammablevapors.Keeppumpassemblyinwellventilated

area.Donotspraypumpassembly.

 • Donotsmokeinthesprayarea.

 • Donotoperatelightswitches,engines,orsimilarsparkproducingproducts

in the spray area.

 • Keepareacleanandfreeofpaintorsolventcontainers,rags,andother

ammablematerials.

 • Knowthecontentsofthepaintandsolventsbeingsprayed.Readall

materialSafetyDataSheets(SDS)andcontainerlabelsprovidedwiththe

paintsandsolvents.Followthepaintandsolventmanufacture’ssafety

instructions.

 • Placepumpatleast25feet(7.62meters)fromthesprayobjectinawell

ventilatedarea(addmorehoseifnecessary).Flammablevaporsareoften

heavierthanair.Floorareamustbeextremelywellventilated.Thepump

contains arcing parts that emit sparks and can ignite vapors.

 • Plasticcancausestaticsparks.Neverhangplastictoenclosesprayarea.Do

notuseplasticdropclothswhensprayingammablematerial.

 • Fireextinguisherequipmentshallbepresentandworking.

WARNING: INJECTION INJURY

Ahighpressurepaintstreamproducedbythisequipmentcanpierce

theskinandunderlyingtissues,leadingtoseriousinjuryandpossible

amputation. See a physician immediately.

PREVENTION:

 • Donotaimthegunat,orsprayanypersonoranimal.

 • Keephandsandotherbodypartsawayfromthedischarge.Forexample,do

nottrytostopleakswithanypartofthebody.

 • NEVERputyourhandinfrontofthegun.Gloveswillnotprovideprotection

against an injection injury.

 • ALWAYSkeepthetipguardinplacewhilespraying.Thetipguardprovides

someprotectionbutismainlyawarningdevice.

 • Onlyuseanozzletipspeciedbythemanufacturer.

 • Usecautionwhencleaningandchangingnozzletips.Inthecasewherethe

nozzletipclogswhilespraying,ALWAYSlockguntrigger,shutpumpo,

andreleaseallpressurebeforeservicing,cleaningtiporguard,orchanging

tip.Pressurewillnotbereleasedbyturningothemotor.ThePRIME/

SPRAYvalveorpressurebleedvalvemustbeturnedtotheirappropriate

positionstorelievesystempressure.RefertoPRESSURERELIEFPROCEDURE

describedinthepumpmanual.

 • Donotleavetheunitenergizedorunderpressurewhileunattended.

Whentheunitisnotinuse,turnotheunitandrelievethepressurein

accordancewiththemanufacturer’sinstructions.

 • High-pressuresprayisabletoinjecttoxinsintothebodyandcauseserious

bodilyinjury.Intheeventthatinjectionoccurs,seekmedicalattention

immediately.

 • Checkhosesandpartsforsignsofdamage,aleakcaninjectmaterialinto

theskin.Inspecthosebeforeeachuse.Replaceanydamagedhosesor

parts.OnlyuseTITANoriginal-high-pressurehosesinordertoensure

functionality,safetyanddurability.

 • Thissystemiscapableofproducing3600PSI/248Bar.Onlyuse

replacementpartsoraccessoriesthatarespeciedbythemanufacturer

andthatareratedaminimumof3600PSI.Thisincludesspraytips,nozzle

guards,guns,extensions,ttings,andhose.

 • Alwaysengagethetriggerlockwhennotspraying.Verifythetriggerlockis

functioning properly.

 • Verifythatallconnectionsaresecurebeforeoperatingtheunit.

 • Knowhowtostoptheunitandbleedpressurequickly.Bethoroughly

familiarwiththecontrols.Pressurewillnotbereleasedbyturningothe

motor.ThePRIME/SPRAYvalveorpressurebleedvalvemustbeturnedto

theirappropriatepositionstorelievesystempressure.RefertoPRESSURE

RELIEFPROCEDUREdescribedinthepumpmanual.

 • Alwaysremovethespraytipbeforeushingorcleaningthesystem.

NOTE TO PHYSICIAN: Injection into the skin is a traumatic injury which can

lead to possible amputation. It is important to treat the injury as soon as

possible. DO NOT delay treatment to research toxicity. Toxicity is a concern

with some coatings injected directly into the blood stream. Consultation

with a plastic surgeon or reconstructive hand surgeon may be advisable.

WARNING: GENERAL

Cancausesevereinjuryorpropertydamage.

PREVENTION:

 • Alwayswearappropriategloves,eyeprotection,clothingandarespiratoror

mask when painting.

 • Donotoperateorspraynearchildren.Keepchildrenawayfromequipment

at all times.

 • Donotoverreachorstandonanunstablesupport.Keepeectivefooting

andbalanceatalltimes.

 • Stayalertandwatchwhatyouaredoing.

 • Donotoperatetheunitwhenfatiguedorundertheinuenceofdrugsor

alcohol.

 • Donotkinkorover-bendthehose.Airlesshosecandevelopleaksfrom

wear,kinkingandabuse.Aleakcaninjectmaterialintotheskin.

 • Donotexposethehosetotemperaturesorpressuresinexcessofthose

speciedbymanufacturer.

 • Donotusethehoseasastrengthmembertopullorlifttheequipment.

 • Uselowestpossiblepressuretoushequipment.

 • Followallappropriatelocal,stateandnationalcodesgoverningventilation,

re prevention and operation.

 • TheUnitedStatesGovernmentSafetyStandardshavebeenadopted

undertheOccupationalSafetyandHealthAct(OSHA).Thesestandards,

particularlypart1910oftheGeneralStandardsandpart1926ofthe

ConstructionStandardsshouldbeconsulted.

 • Beforeeachuse,checkallhosesforcuts,leaks,abrasionorbulgingofcover.

Checkfordamageormovementofcouplings.Immediatelyreplacehose

ifanyofthoseconditionsexist.Neverrepairapainthose.Replacewitha

conductivehigh-pressurehose.

 • Donotsprayoutdoorsonwindydays.

 • Alwaysunplugcordfromoutletbeforeworkingonequipment(electric

modelsonly).

for professional use only • instruction sheet

LX-75 ProfessionaL airLess gun

4’ gun 550-495

8’ gun 550-500

0318 • Form No. 313-2684E

English

 2 ©TitanToolInc.Allrightsreserved.

Setup

Never attempt to assemble, change, or clean the gun, tip,

or tip guard without first relieving pressure from the spray

system. Follow the “Pressure Relief Procedure” in the

sprayer’s Owner’s Manual.

Always use a tip safety guard for added

protection against injection. Beware

that the guard alone will not prevent

injection. Never cut off tip guard! Always

engage gun trigger lock when the gun is

not in use. Before servicing equipment,

consult Owner’s Manuals and follow all

warnings.

Trigger lock in

locked position.

 1. Setupthesprayer.Refertotheinstructionsin

thesprayer’sOwner’sManual.

 2. Attachaconductiveorgrounded,airlessspray

hosetothematerialinletonthegun.Usingtwowrenches(oneon

thegunandoneonthehose),tightensecurely.

 3. Withthetipguard,tipswivel,andpolemountothegun,start

thesprayer.Flushandpreparethespraysystemaccordingtothe

sprayer’sOwner’sManual.Inspectthespraysystemtomakesurethat

all ttings are secure and that there are no leaks.

Diuser

Seal Washer

Tip

Seal

Pole Moun

Retaining Nut

Tip Swivel

Tip Seal Retainer

Tip Guard

 4. Performthe“PressureReliefProcedure”describedinthesprayer’s

Owner’sManual.

 5. Placethesealwasherandpolemountoverthediuser,andsecurein

position using the retaining nut. Tighten securely using a wrench.

 6. Threadthetipswivelontothepolemount.Tightensecurelyusinga

wrench.

 7. Threadthetipguardontothetipswivel.Tightensecurelyusinga

wrench.

Operation

 1. Insertthedesiredtipassemblyintothetipguard.

 2. Startthesprayer.Refertotheinstructionsinthesprayer’sOwner’s

Manual.

 3. Adjusttheuidpressureonthesprayeruntilthesprayiscompletely

atomized.Alwayssprayatthelowestpressurenecessarytogetthe

desired results.

NOTE: The spray tip determines the size of spray pattern and

coverage. When more coverage is needed, use a larger tip

instead of increasing uid pressure.

 4. Operatethetriggerandusethesamesprayingtechniquesaswith

standardpistol-gripairlesssprayguns.

Use extreme caution when spraying with a extension pole.

Do not spray near power lines. Avoid all other over-head

obstacles.

Changing a Tip

Tipscanberemovedandreplacedeasilywithoutdisassemblingthegun.

Never attempt to change or clean the tip or tip guard without

first performing the “Pressure Relief Procedure.”

 1. Performthe“PressureReliefProcedure”describedinthesprayer’s

Owner’sManual.

 2. Removethetipfromtheslotonthetipguard.

 3. Insertthenewtipintotheslotonthetipguard.Thearrowonthetip

handleshouldbepointingintheforwarddirectionforspraying.

Removing the Tip Seal and Tip Seal Retainer

Tip

Guard

Tip

Tip Seal Retainer

Tip Seal

 1. Removethetipfromthetip

guard.

 2. Insertthetiphandlethroughthe

front of the tip guard.

 3. Pushthetipsealandtipseal

retaineroutthroughthebackof

the tip guard.

Identifying Tip Sizes

Toidentifytipsizes,usethefollowing

formula.A“517”tipsizewillbeusedin

this example.

Therstdigitmultipliedbytworepresentsthesizeofthespraypatternwhen

spraying12”awayfromtheworksurface:

5x2=10”spraypattern

Thesecondtwodigitsrepresentthediameteroftheoriceonthetip:

17=.017”orice

Cleanup

Maintainingacleangunisimportanttoensuretrouble-freeoperation.

Removethetipguard,tipswivel,andpolemount,andushthegunaftereach

use.Storeinadrylocation.Donotleavethegunoranyofitspartsinwater

or solvents.

Special cleanup instructions for use with flammable solvents:

 • Alwaysushspraygunpreferablyoutsideandatleastonehose

length from spray pump.

 • Ifcollectingushedsolventsinaonegallonmetalcontainer,

place it into an empty ve gallon container, then ush solvents.

 • Areamustbefreeofammablevapors.

 • Followallcleanupinstructions.

IMPORTANT: The sprayer, hose, and gun should be cleaned thoroughly

after daily use. Failure to do so permits material to cake, seriously

affecting the performance of the unit.

Always spray at minimum pressure with the tip guard, tip

swivel, and pole mount removed when using mineral spirits

or any other solvent to clean the sprayer, hose, or gun. Static

electricity buildup may result in a fire or explosion in the

presence of flammable vapors. Hold the gun firmly against a

metal container while flushing.

Maintenance

Follow all safety precautions as described in the Safety

Precautions section of this manual before proceeding.

Replacing/Servicing the Seal Assembly

Ifthespraygunleaksorspitsatthetipwhenthetriggerisreleased,theseal

assemblyisworn,damaged,ordirtyandmustbereplacedorcleaned.

Never attempt to perform maintenance on the spray gun

without first performing the “Pressure Relief Procedure.”

 1. Disconnecttheairlesssprayhosefromthegun.

 2. Placeonewrenchonthegunheadttingandanotherwrenchonthe

rear tting of the extension pole. Turn the entire extension pole to

unthreaditfromthegunheadtting.Makesurethettingonthe

extension pole does not move during its removal.

IMPORTANT: Do not try to remove either of the fittings on the extension

pole. Movement of these fittings will break the factory seal and cause the

gun to leak.

 3. Carefullyremovetheentireextensionpoletoexposetheshaftand

ballholder.Makesurethettingontheextensionpoledoesnot

move during removal of the extension pole.

 4. Placealockingpliersontheshaftascloseaspossibletotheseal

assembly.Whileholdingthesealassemblyinplacewithawrench,

unthreadtheshaftfromthesealassemblyusingthelockingpliers.

 5. Removethetriggerguard.

 a. Pullthebackofthetriggerguarddownsothatitcomesloose

fromtheswivelassemblyonthehandle.

 b. Twistthefrontofthetriggerguardoutoftheslotinthegun

head.

©TitanToolInc.Allrightsreserved. 3

 6. Removethetwotriggerscrewsthatsecurethetriggertothegun

head.Removethetrigger.

Shaft

Lock Nut

Trigger Scre

Trigger

Trigger Guard

Seal

Assembly

Seal

Washer

Rear Fitting

Extension Pole

O-Ring

Gun Head F

ittiing

 7. Placethegunheadinaviseandremovethegunheadtting.

 8. Usinga3/8”socket,removethelocknutfromthethreadedendofthe

sealassemblyinsidethebackofthegunhead.

 9. Usingapliers,pullthesealassemblyfromthefrontofthegunhead.

Becarefulnottodamagethethreadsinsidethegunhead.

 10. Removethesealwasherfromthegunhead.

 11. Soaktheremovedpartsintheappropriatesolventandwipeclean.

 12. Inspectthepartsforwearordamageandusenewpartsduring

reassemblyofthegun,whennecessary.

NOTE: Lubricate all packings and moving parts with a lithium-

based grease before reassembly.

 13. Installthenewsealassemblyintothefrontofthegunhead.Make

surethethreadedportionofthesealassemblyisalignedwiththe

rectangularholeinthebackofthegunhead.

 14. Threadthelocknutontothethreadedshaftofthesealassemblyin

thebackofthegunhead.Tightenthenutuntilapproximately1/16”

ofthesealassemblyshaftsticksoutpastthenut.

 15. Applyalithium-basedgreasetobothsidesofthenewsealwasherand

insert the washer into the groove inside the gun head.

 16. Installthegunheadttingintothegunheadandtightenuntilthehex

onthettingmeetsthegunhead.Makesurethesealwasherremains

in the groove inside the gun head during installation. Torque to

45–50ft./lbs.

 17. Reassemblethetrigger.

 18. Inspecttheo-ringonthegunheadttingandreplaceifnecessary.

 19. ApplyLoctitetothethreadsontheshaft.Holdthesealassemblyin

placewithawrenchandthreadtheshaftintothesealassemblyuntil

itstopsonthechamferedshoulder.Donotapplyexcessiveforceon

the shaft.

 20. Lubricatetheo-ringonthegunheadttingandreassemblethe

extensionpoletothegunheadtting.Triggerthegunbeforenal

tighteningoftheextensionpoletopreventdamagetotheballholder.

 21. Testtheoperationofthetrigger.Thereshouldbeasmallamountof

play in the trigger after the trigger is released. This will ensure that

theballholderisfullyseatedinthediuserandthegunisshuto

when the trigger is released. Adjust the position of the lock nut on the

sealassemblyiftriggeradjustmentisnecessary.

 22. Reassemblethetriggerguard.

 23. Startthesprayerandpressurizethegun(refertotheinstructionsin

thesprayer’sOwner’sManual).Checkthegunforleaks.

 24. Movethetriggerlocktothelockedposition.Pullthetriggerand

check for leaks.

Replacing the Ball Holder and Diuser

Usethefollowingproceduretoreplacetheballholderanddiuseronthe

spray gun.

Never attempt to perform maintenance on the spray gun

without first performing the “Pressure Relief Procedure.”

 1. Disconnecttheairlesssprayhosefromthegun.

 2. Removethetipguard,tipswivel,andpolemountfromthegun.

 3. Placeonewrenchonthegunheadttingandanotherwrenchonthe

rear tting of the extension pole. Turn the entire extension pole to

unthread it from the gun head tting.

IMPORTANT: Do not try to remove either of the fittings on the extension

pole. Movement of these fittings will break the factory seal and cause the

gun to leak.

 4. Carefullyremovetheentireextensionpoletoexposetheshaftand

ballholder.Makesuretothesupporttheshaftduringremovalofthe

extension pole.

Shaft

Ball

Holder

 5. Placealockingpliersontheshaftas

closeaspossibletotheballholder.

Whileholdingtheshaftinplacewith

thelockingpliers,unthreadtheball

holder from the shaft using a wrench.

 6. ApplyLoctitetothethreadsofthe

shaftandthreadthenewballholderontotheshaftuntilitstopsat

theangledshoulderoftheshaft.Donotapplyexcessiveforceonthe

shaftorballholder.

Extension Pole

Diuser

Front Fitting

 7. Placeonewrenchonthewrenchats

ofthediuserandanotherwrench

on the front tting of the extension

pole.Unthreadthediuserfromthe

extensionpole.Makesurethetting

on the extension pole does not move

duringremovalofthediuser.

 8. Threadthenewdiuserintothefront

ttingoftheextensionpole.Makesuretoholdthettingonthe

extensionpolewithawrench.Torquethediuserto40-50ft./lbs.

 9. Inspecttheo-ringonthegunheadttingandreplaceifnecessary.

 10. Lubricatetheo-ringonthegunheadttingandreassemblethe

extensionpoletothegunheadtting.Triggerthegunbeforenal

tighteningoftheextensionpoletopreventdamagetotheballholder.

 11. Testtheoperationofthetrigger.Thereshouldbeasmallamountof

play in the trigger after the trigger is released. This will ensure that

theballholderisfullyseatedinthediuserandthegunisshuto

when the trigger is released. Adjust the position of the lock nut on the

sealassemblyiftriggeradjustmentisnecessary.

 12. Startthesprayerandpressurizethegun(refertotheinstructionsin

thesprayer’sOwner’sManual).Checkthegunforleaks.

 13. Movethetriggerlocktothelockedposition.Pullthetriggerand

check for leaks.

Replacing/Removing the Filter

 1. Pullthebackofthetriggerguarddownsothatitcomesloosefrom

theswivelassemblyonthehandle.

 2. Removethehandleassemblyfromthegunhead.

 3. Pulltheoldlteroutofthegunhead.

 4. Pushtheneworcleanedlterintothegunhead.

 5. Makesurethehandlesealisinpositionandthreadthehandle

assemblyintothegunheaduntilsecure.

 6. Snapthetriggerguardbackontothehandleassembly.

Filter Chart

Part

Number

Application Filter Type Color of

Filter Body

550-486 Syntheticresin,enamels,clean

varnishes,stains,azures

Extrane red

550-485 Basecoatenamels,primer

enamels,llers,markingpaints,

textured enamels

Fine yellow

550-483 Emulsions,latexpaints,acrylic

paints

Medium white

550-484 Fillerpaints,largeareasurfaces Coarse green

English

Warranty

TitanTool,Inc.,(“Titan”)warrantsthatatthetimeofdeliverytotheoriginalpurchaserforuse(“EndUser”),theequipmentcoveredbythiswarrantyisfreefrom

defectsinmaterialandworkmanship.Withtheexceptionofanyspecial,limited,orextendedwarrantypublishedbyTitan,Titan’sobligationunderthiswarranty

islimitedtoreplacingorrepairingwithoutchargethosepartswhich,toTitan’sreasonablesatisfaction,areshowntobedefectivewithintwelve(12)monthsafter

saletotheEndUser.ThiswarrantyappliesonlywhentheunitisinstalledandoperatedinaccordancewiththerecommendationsandinstructionsofTitan.

Thiswarrantydoesnotapplyinthecaseofdamageorwearcausedbyabrasion,corrosionormisuse,negligence,accident,faultyinstallation,substitutionofnon-

Titancomponentparts,ortamperingwiththeunitinamannertoimpairnormaloperation.

DefectivepartsaretobereturnedtoanauthorizedTitansales/serviceoutlet.Alltransportationcharges,includingreturntothefactory,ifnecessary,aretobe

borneandprepaidbytheEndUser.RepairedorreplacedequipmentwillbereturnedtotheEndUsertransportationprepaid.

THEREISNOOTHEREXPRESSWARRANTY.TITANHEREBYDISCLAIMSANYANDALLIMPLIEDWARRANTIESINCLUDING,BUTNOTLIMITEDTO,THOSEOF

MERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE,TOTHEEXTENTPERMITTEDBYLAW.THEDURATIONOFANYIMPLIEDWARRANTIESWHICH

CANNOTBEDISCLAIMEDISLIMITEDTOTHETIMEPERIODSPECIFIEDINTHEEXPRESSWARRANTY.INNOCASESHALLTITANLIABILITYEXCEEDTHEAMOUNTOF

THEPURCHASEPRICE.LIABILITYFORCONSEQUENTIAL,INCIDENTALORSPECIALDAMAGESUNDERANYANDALLWARRANTIESISEXCLUDEDTOTHEEXTENT

PERMITTEDBYLAW.

TITANMAKESNOWARRANTYANDDISCLAIMSALLIMPLIEDWARRANTIESOFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSEWITHRESPECTTO

ACCESSORIES,EQUIPMENT,MATERIALSORCOMPONENTSSOLDBUTNOTMANUFACTUREDBYTITAN.THOSEITEMSSOLD,BUTNOTMANUFACTUREDBYTITAN

(SUCHASGASENGINES,SWITCHES,HOSES,ETC.)ARESUBJECTTOTHEWARRANTY,IFANY,OFTHEIRMANUFACTURER.TITANWILLPROVIDETHEPURCHASER

WITHREASONABLEASSISTANCEINMAKINGANYCLAIMFORBREACHOFTHESEWARRANTIES.

Parts List

Item Part # Description Quantity

 1 520-099 Diuser,“G”thread............................1

 2 651-020 Sealwasher ..........................................1

 3 711-010 Polemount ........................................... 1

 4 611-652 Retainingnut,“G”thread ................1

 5 611-418 Tipswivelassembly,“G”thread ....1

 6 651-020 Tipseal ...................................................1

 7 661-517 Tipassembly,SC6 ..............................1

 8 661-012 Tipguard,“G”thread ........................ 1

 9 651-040 Tipsealretainer ..................................1

 10 550-514 Ballholderassembly ......................... 1

 11 580-513 Triggerscrew,short ...........................1

 12 550-466 O-ring .....................................................1

 13 550-456 Gunheadtting .................................1

 14 550-437 Sealwasher ..........................................1

 15 550-458 Packingsealassembly ...................... 1

 16 226-001 Locknut ................................................. 1

 17 550-464 Extensionpoleassembly,4’ ...........1

  550-501 Extensionpoleassembly,8’

 18 580-530 Swivelassembly .................................1

 19 550-488 Filterspring ..........................................1

 20 550-483 Filter,medium ..................................... 1

 21 580-531 Gunhandle ........................................... 1

 22 560-038 Handleseal ........................................... 2

 23 550-448 Gunhead ...............................................1

 24 550-454 Triggerscrew,long ............................ 1

 25 550-455 Trigger ....................................................1

 26 550-452 Triggerguard .......................................1

 27 0286932 4’needleassembly ............................1

  0286933 8’needleassembly ............................1

  550-521 Gunrepairkit(includesitems12

and14–16)

  550-518 Diuser/ballholderrepairkit,“G”

thread

   (includesitems1,10,and12)

  651-139 Tipguardandswivelassembly,“G”

thread

   (includesitems2–5and8)

  0286937 Majorrepairkit,4’(includesitems

10,12,14-16and27)

  0286938 Majorrepairkit,8’(includesitems

10,12,14-16and27)

Titan LX-75 Airless Spray Gun User manual

Related papers

Other documents