Yardworks 060-2279-2 Owner's manual

Brand
Yardworks
Model
060-2279-2
Category
Grass trimmers
Type
Owner's manual
ELECTRIC GRASS TRIMMER/EDGER
060-2279-2
Owner’s Manual
Toll-free helpline: 1-866-523-5218
Read all safety rules and instructions carefully before operating this tool.
2
ELECTRIC GRASS TRIMMER/EDGER
Type Corded
Voltage 120 V~60 Hz
Amp 5.0 A
Speed 8,000 RPM (no load)
Line Size 0.065” (1.65 mm)
Cutting path 14” (35 cm)
Cutting Line Length 2×4 m
Weight 5.5 lbs (2.5 kg)
Spool line 60-2269-6
Contents
Contents…… ……..………………………………………………………………………….……….
Specifications..……………………………………………………………………………...…………
Warranty………………………………………………………………………………………………..
General Safety Rules……………………………………………………………………...…...…….
Electrical Information……………..……..………….……………………..……………………….…
Know Your String Trimmer..……………………………………………………………….…….......
Assembly……………..………………………………………………………………………………..
Operation……………….…………………………………………………………………….……….
Maintenance…..…………………………………………………………………………….….…….
Troubleshooting.……………………………………………………………………………..……….
Symbols……………………………….……………………………...………………..….…………..
Exploded View……………………………………………………...………………….…..….……..
Parts List……..………………………………………………………………………………………..
2
2
3
4
6
7
8
10
11
13
14
15
16
Specifications
3
TWO-YEAR LIMITED WARRANTY
For TWO YEARS from the date of purchase within Canada, YARDWORKS CANADA will, at its
option, repair or replace for the original purchaser, free of charge, any part or parts found to be
defective in material or workmanship.
This warranty does not cover:
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident,
improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner's manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.
Full One Hundred Twenty Days Warranty on Normal Wear Parts: Normal wear parts are defined as
blade adaptors, blades, grass bags and tires. These parts are warranted to the original purchaser to
be free from defects in material and workmanship for a period of one hundred twenty (120) days
from the date of retail purchase.
How to Obtain Service: Warranty service is available by calling the toll-free helpline, at 1 866-523-5218.
The factory will not accept the return of a complete unit unless prior written permission has been
extended by YARDWORKS CANADA.
Transportation Charges: Transportation charges for the movement of any power equipment unit or
attachment are the responsibility of the purchaser. The purchaser must pay transportation charges
for any part submitted for replacement under this warranty unless such return is requested in writing
by YARDWORKS CANADA.
Other Warranties: All other warranties, express or implied, including any implied warranty of
merchantability is limited in its duration to that set forth in this express limited warranty. The provisions
as set forth in this warranty provide the sole and exclusive remedy of YARDWORKS CANADA
obligations arising from the sale of its products.
YARDWORKS CANADA will not be liable for incidental or consequential loss or damage.
Warranty
4
WARNING:
When using this device, safety precautions must be followed. For your own safety and that of
bystanders, please read these instructions before operating the device. Do not use the device without
reading the instruction sheet. Please keep the instructions safe for later use.
• This grass trimmer is designed for cutting grass and similar soft vegetation and for trimming
grass edges in private and hobby garden areas which are not accessible with a lawnmower.
• The device is not designed for use in public gardens, parks, sports centres or at roadsides
nor in agriculture and forestry.
• This grass trimmer is not designed to be used for cutting or chopping:
- Hedges, shrubs and bushes,
- Flowers,
- Or for composting purposes
Failure to comply with these requirements could lead to personal injury.
• This device is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure that they do not play with the device.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• Wear protective glasses or goggles.
• Never allow children or people unfamiliar with the instructions to use the device.
• Turn off the device while people, especially children, or pets are nearby.
• Only use the device in daylight or good artificial light.
• Before using the device and after any impact, check for signs of wear or damage and repair
as necessary.
• Never operate the device with damaged guards or without the guards in place.
• Keep hands and feet away from the trimmer cutting line at all times and in particular when switching
on the motor.
• Take care against injury from any device fitted for trimming the cutting line length. After
extending new cutting line always return the device to its normal operating position before
switching on.
• Never fit metal cutting elements.
• Never use replacement parts or accessories not provided or recommended by the manufacturer
• Disconnect the device from the power supply before checking, cleaning or repairing it
and when it is not in use.
• Always ensure that ventilation openings are kept clear of debris.
ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR GRASS TRIMMER
• Do not expose to moisture.
• Use only on AC power supply voltage shown on the product rating label.
• Avoid operating your trimmer in wet grass, where feasible.
• Take care not to lose your footing in wet grass.
• On slopes, be extra careful not to slip and wear nonslip footwear.
• Do not walk backwards when trimming as you could trip. Walk never run.
• Switch off before pushing the trimmer over surfaces other than grass.
• Never pick up or carry a trimmer by the power cable.
• Do not lean over the trimmer guard. Objects may be thrown by the cutting line.
• Keep all nuts, bolts and screws tight to be sure the trimmer is in safe working condition.
General Safety Rules
5
• To avoid the risk of injury, keep fingers and hands clear of the cutting line at the leading edge
of the guard.
MAINTENANCE
• After use, disconnect the device from the power supply and check for damage.
• When not in use, store the device out of the reach of children
• An electric trimmer should only be repaired by an authorised repairer.
• Use only manufacturer-recommended replacement parts and accessories.
Preparation for use, operation and maintenance of the appliance:
- Read the instructions carefully;
- Be familiar with the controls and proper use of the equipment;
- Before use, check the power and extension cords for signs of damage or wear;
- If the cord is damaged during use, disconnect the cord from the power supply
immediately.
DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY.
- Do not use the lawn trimmer (edge trimmer), if the cords are damaged or worn.
WARNING!
- Cutting elements continue to rotate after the motor is switched off;
- Keep extension cords away from cutting elements;
- It is recommended that power for the device should be supplied via a residual current device
(RCD) with a tripping current of not more than 30mA.
6
CAUTION!
Always make sure that your outlet is properly grounded. If you are uncertain, have it checked by
a certified electrician.
WARNING!
This grass trimmer is for outdoor use only. Do not expose to rain or use in damp locations.
GUIDELINES FOR USING EXTENSION CORDS
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause overheating. The table below shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
Minimum Gauge for Extension Cords (AWG)
(when using 120 V only)
Make sure your extension cord is properly wired and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a qualified person before use. Keep extension cords
away from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit should comprise a wire of at least 12
gauge and should be protected with a 15 A time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF position and the electric current is identical to
that stamped on the motor nameplate. Running at a lower voltage will damage the motor.
WARNING!
Although this device is double-insulated, the extension cord and receptacle must still be
grounded while in use to protect the operator from electric shock.
Ampere Rating Total Length of Cord in Feet (meters)
More Than Not More Than 25′ (7.6 m) 50′ (15 m) 100′ (30.4m) 150’ (45.7 m)
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
Electrical Information
7
Know Your String Trimmer
KNOW YOUR STRING TRIMMER
The safe use of this product requires an understanding of the information on the product and in
this operator’s manual as well as a knowledge of the project you are attempting. Before use of
this product, familiarize yourself with all operating features and safety rules.
8
WARNING!
Before assembly, make sure that the tool is switched off and unplugged.
Fitting the guard (See Figure 2 & Figure 3.)
1. Secure the guard with 3 screws.
2. Place the safety guard onto the motor housing as shown, pivot the guard anti-clockwise to the position of
figure 3. Secure the guard with the screw.
WARNING!
Never use the tool unless the guard is properly fitted.
Fitting the secondary handle (See Figure 4 & Figure 5.)
1. Place the handle on the tool as shown.
2. Adjust the handle to the most comfortable position. Use the marking as a guide.
3. Pass the bolt through the secondary handle and the main handle.
4. Screw the nut into the other side of the bolt. Do not over-tighten the bolt.
Assembly
9
Preparing the trimmer for use (See Figure 6 & Figure 7.)
1. Turn the adjustment collar clockwise to unlock. You can slide the telescopic tube up or down to
achieve comfortable working height.
2. Turn the adjustment collar counter-clockwise until the shaft locks into place.
WARNING!
Never attempt to lock the trigger lever in the on position.
Hint for optimum use (See Figure 8.)
In order to achieve optimum cutting results, only cut dry grass.
Trimming
1. Hold the tool as shown.
2. Gently swing the trimmer from side to side .
3. When cutting long grass, work in stages from the top. Take small cuts. Keep the tool away from hard
objects and delicate plants.
4. If the tool starts running slowly, reduce the load.
Operation
10
Adjusting cutting head angle (See Figure 9.)
Press the button and move the shaft to the lowest position. The shaft will rotate to the 3
positions, when button is pressed. When the shaft is in position, the button will lock into place.
Using the edge guide (See Figure 10.)
If necessary the distance bracket can be swung down until it locks. Use the edge guide,
for example, to cut around plants.
Adjusting the line length manually (See Figure 11.)
Disconnect the plug from the mains socket!
Press the retaining head (B), release it again and pull the ends of the cord out a little. Repeat this process
until the ends of the cord project a little beyond the cord cutter (A).
Fully automatic dual line system
The trimmer features a fully automatic dual line system so that the lines are automatically lengthened each
time the trimmer is switched on after a standstill. If the lines should be longer that defined by the cutting
circle then they will be automatically cut to the correct length by the line cutter (A).
11
Edging (See Figure 12 & Figure 13.)
For edging, push the button and rotate the handle. The handle will rotate to 90°, 180° position, while
releasing the button. When the hand is in position, the button will lock into place. The hand will only rotate in
one direction. Do not use the heavy duty cutting system for edging.
3-position adjustment (See Figure 14.)
1. Push the yellow button
2. Adjust handle to the desired angle
3. Release the button. The handle locks in position.
Secure the power cable (See Figure 15.)
Form a loop in the end of the extension cable, conduct it through the opening in the upper handle and hang
it on to the strain relief.
12
Your device has been designed to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon proper tool care and regular
cleaning.
WARNING!
Before performing any maintenance, switch off and unplug the tool.
• Regularly clean the ventilation slot in your device using a soft brush or dry cloth.
• Regularly clean the cutting line and spool using a soft brush or dry cloth.
• Regularly use a blunt scraper to remove grass and dirt from underneath the
guard.
Fitting a new spool of cutting line (See Figure 16 & Figure 17.)
1. Unplug the tool
2. Keep the tabs depressed and remove the spool cover from the housing. Remove
the empty spool from the spool cover .
3. Remove any dirt and grass from the spool cover and housing
4. Take the new spool (60-2269-6) and push it into the boss in the spool cover. Rotate the
spool slightly until it is seated.
5. Unclip the end of one of the cutting lines and guide the line into one of the eyelets. The
line should protrude approx. 10 cm from the spool cover.
6. Unclip the end of the other cutting line and guide the line into the other eyelet. The line
should protrude approx. 10 cm from the spool cover.
7. Align the tabs on the spool cover with the cut outs in the housing.
8. Push the cover onto the housing until it snaps securely into place.
WARNING!
If the cutting lines protrude beyond the trimming blade, cut them off so that they just reach the blade.
NOTE!
Auto feed function works during [the] starting and stopping of trimmer. Strings will extend
approximately 3/16" each time switch trigger is depressed and released WHILE NOT TRIMMING until
the strings reach the length of the grass deflector blade. It may take up to 10 complete starting and
stoppings to advance the line.
Maintenance
13
Winding new line onto a spool (See Figure 18 & Figure 19 & Figure 20.)
1. You may wind new cutting line onto an empty spool.
2. Replacement packs of cutting line are available from dealer.
3. Remove the empty spool from the tool as described above.
4. Remove any remaining cutting line from the spool.
5. First feed 10 cm of cutting line (7) into two eyelets, one eyelet (8) in the upper section of the spool as
shown, the other eyelet in the lower section not shown, but still proceeding in the same manner as shown
for the upper section.
6. Wind the cutting line onto the spool in the direction of the arrow (9). Make sure to wind the line neatly and
in layers. Do not criss-cross.
7. Feed cutting line (7) into the two parking slots (10) in the upper section of the spool as shown, the other
two parking slots in the lower section by proceeding in the same manner as shown for the upper section.
8. Finish winding and proceed as described above to fit the spool on the device. Do not forget to release
the cutting line from the parking slot.
WARNING!
Only use the appropriate type of cutting line.
14
If your device is not operating properly, follow the instructions below. If this
does not solve the problem, please contact your local repair agent.
WARNING!
Before proceeding, switch off and unplug.
Tool runs slowly
• Check that the spool housing can rotate freely. Carefully clean it if necessary.
• Check that the cutting line does not protrude more than 11cm from the spool housing. If it
does, cut it off so that it just reaches the line trimming blade.
Automatic line feed does not work.
• Press the tabs and remove the spool cover from the housing.
• Pull the cutting line until it protrudes 11cm from the housing. If insufficient cutting line is left on the spool,
install a new spool of cutting line as instructed above.
• Align the tabs on the spool cover with the cut outs in the housing.
• Push the cover onto the housing until it snaps securely into place.
• If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade.
• If the automatic line feed still does not work or the spool is jammed, try the following suggestion:
• Carefully clean the spool cover and housing.
• Remove the spool and check if the lever can move freely.
• Remove the spool and unwind the cutting line, then wind it on neatly again as describe above. Replace the
spool as instructed.
Troubleshooting
15
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watts Power
min Minutes Time
Alternating Current Type of current
Direct Current Type or a characteristic of current
Class II Construction Double-insulated construction
No Load Speed Rational speed, at no load
/min Per Minute Revolutions, strokes, surface speed, orbits etc.,
per minute
Wet Conditions Alert Do not expose to rain or use in damp locations
Read The Operator’s Manual
To reduce the risk of injury user must read and
understand operator’s manual before using this
product.
Eye Protection Wear eye protection when operating this
equipment.
Safety Alert Precautions that involve your safety.
Long Hair Failure to keep long hair away from the air inlet could
result in personal injury.
Loose Clothing Failure to keep loose clothing from being drawn into
air intake could result in personal injury.
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
SAVE THESE INSTRUCTIONS
Symbols
16
Exploded View
17
ITEM NO. Drawing No. DESCRIPTION QTY
1 GT15FM.A0.02 right handle assembly 1
2 WODQ10.03.06 switch 1
3 TODQ80.A0.03 wire plug assembly 1
4 GT15FM.A0.01 lock of handle shaft assembly 1
5 GT15FM.00.01 left handle 1
6 GT02FM.00.04 left rotary handle 1
7 GT01FM.00.14 filter 1 2
8 GT01FM.00.15 filter 2 2
9 GT01FM.00.07 left motor shell 1
10 GT15FM.20.20 spool line 1
11 GT15FM.20.01 spool cover 1
12 GT15FM.A0.04 spool assembly 1
13 GT15FM.A0.03 safety guard assembly 1
14 GT01FM.00.11 spacer guard 1
15 TM65XX.00.00 motor assembly 1
16 GT02FM.A0.05 right motor shell assembly 1
17 GT02FM.00.06 bushing button 1
18 TOTHYY.03.12 pressed spring 1
19 GT02FM.A0.04 right rotary handle 1
20 GT01FM.10.00 assistant handle assembly 1
21 GT01FM.A0.02 switch button 1
Made in China
Imported by
YardWorks Canada Toronto, Canada M4S 2B8
Part List
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Yardworks 060-2279-2 Owner's manual

Brand
Yardworks
Model
060-2279-2
Category
Grass trimmers
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents