Ozito OZLT550WA User manual

Brand: Ozito

Model: OZLT550WA

Category: Grass trimmers

Type: User manual

Ozito OZLT550WA

This powerful 550W line trimmer is ideal for trimming lawn edges and grass around shrubs and trees. The 300mm cutting diameter and 1.6mm line diameter make it easy to trim even the toughest grass. The automatic line feed ensures that you always have the perfect amount of line for the job.

The adjustable handle and telescopic handle make it easy to find the perfect working position, and the rotatable main handle provides added comfort and control. The safety guard helps to protect you from flying debris, and the edging wheel and edging guide make it easy to create clean, precise edges.

Ozito OZLT550WA

Line Trimmer

300mm 550W

Instruction Manual

2 Year Replacement Warranty

OZLT550WA

WARNING! Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

To view the full range visit: www.ozito.com.au

0212

1. Cordset

2. Rotatable Main Handle

3. On/Off Switch

4. Extension Cord Securing Lug

5. Lock Button

6. Locking Knob

7. Adjustable Handle

8. Telescopic Handle

9. Telescopic Latch

10. Adjustable Head Lock Button

11. Safety Guard

12. Cutter Head

13. Edging Wheel

14. Edging Guide

15. Cutting Blade

16. Motor Housing

Motor: 550W

Input: 230V, 50Hz

No load speed: 9,600/min

Sound pressure level (dB): ≤83

Sound Power level Lwa (dB(A)): ≤96

Cutting diameter: 300mm

Line diameter: 1.6mm

Feed type: Automatic

SPECIFICATIONS - MODEL NO. OZLT550WA

KNOW YOUR TOOL

TABLE OF CONTENTS

SPECIFICATIONS …………………………………………

INTRODUCTION………………………………………….

ELECTRICAL SAFETY……………………………………

GENERAL SAFETY INSTRUCTIONS .…………………

ADDITIONAL SAFETY INSTRUCTIONS FOR

LINE TRIMMERS …………….…………………………..

ASSEMBLY………………………………………………..

OPERATION ……………………………………………..

MAINTENANCE …………….…………………………..

DESCRIPTION OF SYMBOLS ………………………….

CONTENTS ……………………………………………...

WARRANTY………………………………………………

Page 1

Page 3

Page 4

Page 6

Page 8

Page 9

Page 12

Page 13

Page 14

Page 15

INTRODUCTION

Congratulations on purchasing the Ozito Line Trimmer. We

aim to provide quality tools at an affordable price. We hope

you will enjoy using this line trimmer for many years.

Your Ozito Line Trimmer OZLT550WA has been designed for

trimming lawn edges and grass around shrubs and trees.

This product is intended for DIY use only.

Warning! When using mains-powered tools, basic safety precautions,

including the following, should always be followed to reduce risk of fire,

electric shock, personal injury and material damage.

Read and understand the manual prior to operating this tool.

Save these instructions and other documents supplied with this machine for

future reference.

The electric motor has been designed for 230V only. Always check that the power

supply corresponds to the voltage on the rating plate.

This tool is double insulated in accordance with AS/NZS60335; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a

power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions

when operating this tool. The insulation system is for added protection against

injury resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool.

The type of extension cords used shall not be lighter than ordinary polyvinylchloride

sheathed flexible cord. Before use, inspect the extension lead for signs of damage,

wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use

of an extension lead not suitable for the power input of the tool or which is

damaged or defective may result in a risk of fire and electric shock.

It is recommended that the extension lead is a maximum of 25m in length. Do Not

use multiple extension leads.

ELECTRICAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

Warning! Read all instructions, Failure to follow all instructions listed below

may result in electric shock, fire and/or serious injury. The term “Power Tool”

in all of the warnings listed below refers to your mains operated (corded)

power tool or battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

This appliance is not intended for use by young children or infirm persons unless

they have been adequately supervised by a responsible person to ensure that

they can use the appliance safely.

Young children should be supervised to ensure that they do not play with

the appliance.

1) WORK AREA

a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) Recommendation that the appliance should be supplied with a residual

current device (RCD) with a tripping current of not more than 30mA.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention while operating power

tools may result in serious personal injury.

b) Use safety equipment. Always wear eye protection. Safety equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off position before

plugging in. Carrying power tools with your finger on the switch or plugging in

power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of these

devices can reduce dust related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the rate

for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any

power tool that can not be controlled with the switch is dangerous and must

be repaired.

c) Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools, unplugged & out of the reach of children and do

not allow persons unfamiliar with the power tool or these instructions to

operate the power tool. Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tools

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with

these instructions and in the manner intended for the particular type of

power tool, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from intended could

result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power tool

is maintained.

GENERAL POWER TOOL SAFETY WARNINGS

Hold power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make exposed metal parts of the power tool

"live“ and could give the operator an electric shock.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

Recommendations for the use of a residual current device with a rated residual

current of 30mA or less.

Using an Extension Lead

Extension Cords shall be not lighter than:

• if rubber insulated, ordinary tough rubber sheathed flexible cord (code

designation 60245 IEC 53);

• if polyvinyl chloride insulated, ordinary polyvinyl chloride sheathed flexible cord

(code designation 60227 IEC 53).

Always use an approved extension lead suitable for the power input of this tool.

Before use, inspect the extension lead for signs of damage, wear and ageing. Replace

the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an

extension lead not suitable for the power input of the tool or which is damaged or

defective may result in a risk of fire and electric shock.

It is recommended that the extension lead is a maximum of 25m in length. Do Not

use multiple extension leads.

• Before use check the supply and extension cord for signs of damage or aging. If

the cord becomes damaged during use, disconnect the cord from the supply

immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE

SUPPLY. Do not use the line trimmer if the cord is damaged or worn.

• Keep extension cord away from cutting line.

•Never allow children or people unfamiliar with these instructions to use the line trimmer.

• Avoid using the line trimmer, while people, especially children or pets, are nearby.

•Use the line trimmer only in daylight or good artificial light.

• Never operate the line trimmer with damaged guards or without guards in place.

• Switch on the line trimmer only when the hands and feet are away from the

cutting head.

•Never fit metal cutting blades.

• Use only the manufacturer's recommended replacement parts and accessories.

• Always disconnect the line trimmer from the mains when leaving the line

trimmer unattended.

•Disconnect the line trimmer from the mains before carrying out maintenance or

cleaning work.

LINE TRIMMER SAFETY WARNINGS

• Inspect and maintain the line trimmer regularly. Have the line trimmer repaired

only by an authorized repairer.

• Take care against injury from the blade(s) fitted for trimming the cutting line

length. After extending new cutting line, always return the line trimmer to its

normal operating position before switching on.

• When not in use, store the line trimmer out of the reach of children.

• Face the cutting head away from yourself, other people and animals while the

power is connected to the line trimmer (especially during operation).

• Disconnect the power when changing spools or clearing grass from under

the guard.

• Disconnect the power from the line trimmer before making any adjustments.

• Use both handles.

• Keep ventilation openings clear of debris. Keep handles dry, clean and free of

oil and grease.

• Never reach underneath the line trimmer (the cutting line area) until it has

completely stopped and the power has been disconnected.

LINE TRIMMER SAFETY WARNINGS (cont.)

ASSEMBLY

Warning! Before assembly, make sure that the line trimmer is switched off

and unplugged.

Assembling the telescopic handle

1. Line up the two parts of the telescopic handle assembly.

2. Slide the telescopic latch (9) in the

direction as shown in Fig. A. Hold while

inserting the lower end of telescopic

handle (8) into the upper telescopic

handle.

3. Determine the working height of the

line trimmer required and select the

appropriate notch on the lower end of

the telescopic handle (8).

Fitting the guard

1. Place the safety

guard (11) onto

the line trimmer as

shown in Fig.B.

2. Rotate the guard

anti-clockwise as

indicated in Fig. B,

resulting in the

guard positioned

in place (Fig. C).

3. Secure the safety guard with one of the screws supplied (11a).

4. Secure the edging wheel (13) with the remaining 3 screws (13a).

Warning! Never use the line trimmer unless the guard is properly fitted.

Fitting the secondary handle

1. Place the adjustable handle (7) on the line

trimmer as shown in Fig.D

2. Pass the bolt through the adjustable handle

(7) and the rotatable main handle (2).

3. Screw the locking knob (6) onto the bolt.

4. Select the most comfortable position

and tighten the locking knob (6).

Do not overtighten.

Fig.D

Fig. A

Fig.B Fig.C

13a

11a

OPERATION

Preparing the line trimmer for use

Warning! Never attempt to lock the on/off switch in the ''on'' position.

Warning! The cutting elements continue to rotate after the motor is

switched off.

Hints for use

1. To achieve optimum results only cut dry grass.

2. Hold the line trimmer in the upright position.

3. Gently swing the line trimmer from side to side.

4. When cutting long grass, cut in stages from the top of the grass to the bottom

of the grass.

5. If the motor starts to slow down, reduce cutting load.

To start the line trimmer:

1. Obtain an extension cord and thread it through the slot at the rear of the

rotatable main handle (2) as shown in Fig.E.

2. Loop the extension cord and secure the loop over the extension cord securing

lug (4).

3. Connect the cordset (1) to the extension cord plug.

4. Connect the extension cord to a power supply.

5. Depress the on/off switch (3) to start the motor operating.

Fig.E

OPERATION

(cont.)

Edging mode

For edging, the cutter head (12) should be in the position shown in Fig. F, if it is not:

1. Depress the lock button (5)

2. Rotate the rotatable main handle (2) while depressing the lock button (5).

3. When the rotatable main handle (2) is in position, the lock button (5) will lock

into place.

Note: The main handle (2) will only rotate in one direction.

Adjusting cutter head angle

1. Depress the adjustable

head lock button (10) on

both sides of the motor

housing (16) (Fig. G).

2. Move the telescopic handle

(8) to the desired position.

3. Release the adjustable

head lock button (10).

Fig.F

Fig.G

OPERATION (cont.)

Lengthening the line

While the line trimmer is operating, the cutting line (h) gets worn down and

becomes shorter. This line trimmer is equipped with Automatic Line

Advancement which automatically feeds the additional line to the correct length

as it wears down.

1. If the line does not automatically advance, then the trimmer line may be

tangled or the spool empty. Refer to "Maintenance" section of this manual

for instructions.

2. To automatically advance the line, allow the line trimmer to come to a

complete stop. Restart the line trimmer. Upon starting, the line will

automatically advance approximately 5cm. If a longer length of line is

required, repeat the automatic line advancement instruction.

3. To manually advance the line, ensure the line trimmer is off and turn the line

trimmer upside down. Push the tab on the side of the cutter head (12) and then

pull on the end of both pieces of line protruding from the cutter head (12).

Before each use

1. Make sure the safety guard (11) is correctly installed. Tighten the guard screw.

2. Before trimming, inspect the cutting area for string, wire, branches or other

material that may become entangled in the cutting line and thrown.

During each use

1. Only trim grass when you have adequate lighting.

2. Hold the line trimmer by the rotatable main handle (2) and the adjustable

handle (7) for best control and balance.

3. Stand with the cutting head tipped down at an angle in front, guiding the line

trimmer in a semi-circular motion around you.

4. If possible, guide the line trimmer to the left to cut. The line will cut as soon

as it leaves the guard, and the clippings are thrown away from you.

5. To produce a smoothly trimmed area, move the line trimmer in and out of the

area being cut with consistent speed and height.

6. Use only the tip of the cutting line to do the trimming especially near walls

and fences. Trimming with the side of the cutting line may overload the

motor, wear out the line faster, and break the line more often.

7. If the grass is higher than 15cm (6”) high, trim in stages.

8. When the line trimmer is turned off and the spool stops rotating, the cutting

line will relax and may retract. Feed extra cutting line before storing the unit

to avoid losing the line completely into the spool.

9. If the diameter of the cutting area gets smaller, the line is worn down and

needs to be advanced more often.

10. If the line trimmer is not cutting correctly, the cutting line may not be

feeding properly. Remove and rewind the line spool.

MAINTENANCE

Removing & replacing the spool & line assembly (Fig.H)

1. Unplug the line trimmer and turn it upside down.

2. Keep the tabs (e) depressed and remove the spool cover (a) from the spool housing (c).

3. Remove the empty spool (b) from the spool housing (c).

4. Remove any dirt and grass from the spool cover (a) and spool housing (c).

5. Insert the rewound spool (f) into the spool housing (c). Rotate the spool (f) slightly

until it is seated.

6. Unclip the end of one of the cutting lines and guide the line into one of the

eyelets (g). The line should protrude approx. 11cm from the spool housing (c).

7. Unclip the end of the other cutting line and guide the line into the other eyelet.

The line should protrude approx. 11cm from the spool housing (c).

8. Align the tabs (e) on the spool cover (a) with the cut outs (d) in the spool housing (c).

9. Push the cover (a) onto the housing (c) until it snaps securely into place.

Warning! If the cutting lines protrude beyond the trimming blade, cut them

off so that they just reach the blade.

Winding new line onto a spool (Fig.I)

You may wind new cutting line onto an empty spool. Cutting line is available from any

Bunnings Warehouse. Only use cutting line 1.6mm in diameter or poor performance

and damage to the motor could occur.

Fig. I

Fig.H

DESCRIPTION OF SYMBOLS

Warning Read instruction manual

V Volts Hz Hertz

~ Alternating current W Watts

o No load speed

Double insulated

/min Revolutions or reciprocation per minute

Regulator compliance mark

Wear eye and hearing

protection

Keep bystanders away

Do not operate in the rain

Keep bystanders away

Sound power level

Disconnect and discontinue use should the power-cord be damaged

MAINTENANCE (cont.)

1. Remove the empty spool from the line trimmer as described on previous page.

2. Remove any remaining cutting line from the spool.

3. First feed 10cm of cutting line (a) into the two eyelets (b) in the upper section

of the spool housing (j).

4. Wind the cutting line onto the spool in the direction of the arrow on the spool

housing (j). Make sure to wind the line on neatly and in layers. Do not cross the

line as this will stop it from feeding.

5. Complete winding the line and ensure that the line does not protrude past the

end of the spool edge.

6. Secure the ends of line into the notches (d) while replacing the spool as in Fig. H

on previous page.

• If the housing of the line trimmer requires cleaning, do not use solvents but a

moist, soft cloth only.

• Never let any liquid get inside the line trimmer.

• Never immerse any part of the line trimmer into liquid.

• Keep the motor air vents cleaned and dust-free.

• No lubrication is required as bearings are sealed.

• Store in a cool, dry place after use.

Note: Ozito Industries will not be responsible for any damage or injuries caused

by the repair of the line trimmer by an unauthorised person or by mishandling of

the line trimmer.

AUSTRALIA (Head Office)

1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175

Telephone: 1800 069 486

Facsimile: +61 3 9238 5588

Website: www.ozito.com.au

Email: [email protected]

1 x Line Trimmer

1 x Spool & Line (fitted)

1 x Secondary Handle

1 x Bolt (for secondary handle)

1 x Knob (for secondary handle)

4 x Screws

1 x Edging Wheel

1 x Safety Guard

1 x Instruction Manual

Power tools that are no longer usable should not be disposed of

with household waste but in an environmentally friendly way.

Please recycle where facilities exist. Check with your local council

authority for recycling advice.

Recycling packaging reduces the need for landfill and raw

materials. Reuse of recycled material decreases pollution in the

environment. Please recycle packaging where facilities exist.

Check with your local council authority for recycling advice.

CONTENTS

OZITO INDUSTRIES PTY LTD

CARING FOR THE ENVIRONMENT

SPARE PARTS

Limited spare parts are available subject to availability. Please contact your local

Bunnings Special Orders Desk to order the required spare parts.

Most common spare parts listed below

Spare Part Part No.

Spool & Line ACCLT-005

Spool Cover(Pack 2) SPOZLT550-30

2 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 24 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in

accordance with the terms of this warranty. Warranty excludes consumable parts, for example:

safety guard, spool & line, edging wheel, auxiliary handle.

WARNING

The following actions will result in the warranty being void.

Professional, Industrial or high frequency use.

If the tool has been operated on a supply voltage other than that speciﬁed on the tool.

If the tool shows signs of damage or defects caused by or resulting from abuse, accidents

or alterations.

Failure to perform maintenance as set out within the instruction manual.

If the tool is disassembled or tampered with in any way.

OZITO

Australia/New Zealand (Head Ofﬁce)

1-23 Letcon Drive, Bangholme, Victoria, Australia 3175

•

OW8

WARRANTY

YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER

TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.

PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR

CUSTOMER SERVICE HELPLINE:

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

The beneﬁts provided under this warranty are in addition to other rights and remedies which

are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are entitled to a

replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if

the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under this warranty,

however, where you have suffered any additional direct loss as a result of a defective product

you may be able to claim such expenses by contacting our customer service helpline above.

Australia 1800 069 486

New Zealand 0508 069 486

Ozito OZLT550WA User manual

Brand: Ozito

Model: OZLT550WA

Category: Grass trimmers

Type: User manual

Ozito OZLT550WA

Download PDF

report

Ozito OZLT550WA User manual

Ozito OZLT550WA User manual

Related papers

Other documents