Quick Install Guide Lucetta Roman Tub Faucet, SRT-4670
Step 8
Flush water supply lines
Step 7
Attach water spout
Step 5
Attach handles
Step 4
Attach valve assembly
Step 6
Connect water supply lines
and check for leaks
Step 2
Solder valve assembly together
Step 1
Cut copper tubing to length
nished deck
Step 3
Mount valve assembly
5/64"
1/8"
1 2 3 4
SRT-4670 ............. Chrome finish
SRT-4670-STN .... Satin Nickel finish
Roman Tub Faucet SRT-4670
Installation and Service Instructions
Lucetta®
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects,
or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Model Numbers Tools & Materials Need Help?
Symmons customer service:
Phone: (800) 796-6667
Email: [email protected]
Monday - Friday 7:30 am - 6:00 pm EST
www.symmons.com/service
Compliance
ASME A112.18.1/CSA B125.1
Step 1 Cut copper tubing to length
Step 2 Solder valve assembly together
Length = (d) minus 2-1/4 inches (57 mm) divided by 2.
Example:
-
If center to center distance (d) is 14 inches.
-
14 inches minus 2-1/4 inches = 11-3/4 inches.
-
11-3/4 inches divided by 2 = 5-7/8 inches.
-
Cut 2 copper tubes into 5-7/8 inch lengths.
* Maximum distance (d) with supplied
copper tubing is 18-1/4 inches (463 mm)
center to center distance (d)*
1/2" (12.7 mm) copper tubing
Ensure valves are
parallel aligned
when soldering.
Step 3 Mount valve assembly to deck
Step 4 Attach valve assembly to deck
red
(hot)
blue (cold)
nished deck
front view
Thread down until
stop is reached
nished deck
front view
D1 D2
D1 = D2
Caution: If replacing an older faucet ensure water supply is
turned OFF before removing and then turn faucet handles ON
to relieve water pressure.
Installation Instructions
Page 2
Step 5 Attach faucet handles
Step 6 Solder supply lines to valve inlets
Step 7 Attach faucet spout to deck
OFF = CCW
OFF = CW 5/64"
cold
hot
1/8"
Step 1 Remove faucet handle and collar
Step 2 Remove and replace cartridge
Step 3 Attach collar and faucet handle
Valve cartridge replacement
5/64"
OFF = CCW
OFF = CW 5/64"
Care of faucet finish
Clean nish area by using mild soap and water or non-abrasive
cleaner and then rinse immediately. A non-abrasive wax may
be used to preserve nish area.
Step 8 Flush water supply lines
Page 3
KN-113E
identified
by groove
KN-114E (hot)
OFF = CW
KN-113E (cold)
OFF = CCW valve cartridge
Screw requires
5/64” Allen wrench
RT-CYL-TP-KIT*
2 handles
included
handle (2)
screw (2)
collar (2)
fastener (2)
gasket (2)
Replacement Parts
Part Number Item (Qty)
aerator
RT-106*
Parts Assembly Lucetta Roman Tub Faucet, SRT-4670
handle
screw
collar
fastener
gasket
spout
aerator
valve cartridge
reference table
ange nut
hot/cold identier
valvebody
copper tubing
tee
Ordering replacement parts:
Call Symmons customer service at (800) 796-6667,
(781) 848-2250 M-F 7:30 am - 6:00 pm EST or
check our website at www.symmons.com for a
list of Symmons distributors.
Note: For decorative nish faucets append three
letter sufx code to parts marked with an asterisk (*).
*
screw
base
plug
centerbody
retainer
ange nut
Reference
table
4"
101 mm
2-3/8"
(60 mm)
2-1/16" (52 mm) dia
Connect using
1/2" copper tubing
1" dia. (25 mm)
Hole size
1-1/16" (27 mm) min
1-1/2" (38 mm) max
Finished deck thickness
1-3/8" (35 mm) max
(1)3-3/8" (86 mm) max
for TT style faucet
Dimensions Lucetta Roman Tub Faucet, SRT-4670
8" (203 mm) min
18-1/4" (464 mm) max
with Symmons supplied copper tubing
3-15/16" (101mm)
5-15/16" (151mm)
* TT style faucet
7-11/16" (196 mm)
9-3/8" (238 mm)
8-7/8"
225 mm
6-3/16"
158 mm 2-5/8"
67 mm dia
Note
(1) Use TT style faucet if deck thickness is 1-3/8" to 3-3/8" (35 mm - 86 mm).
Contact Symmons customer service to special order TT style faucet, model number SRT-4670-TT-BDY.
(2) Dimensions subject to change without notice.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
/