Dell PowerEdge SC1435 Quick start guide

www.dell.com | support.dell.com

Dell™ PowerEdge™

SC1435 Systems

Getting Started With

Your System

系统使用入门

開始使用系統

はじめに

시스템시작하기

Model SVUA

www.dell.com | support.dell.com

Dell™ PowerEdge™

SC1435 Systems

Getting Started With

Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

_________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo and PowerEdge are trademarks of Dell Inc.; Microsoft and Windows are registered trademarks,

and Windows Server is a trademark of Microsoft Corporation; Red Hat is a registered trademark of Red Hat, Inc.; SUSE is a registered trademark

of Novell, Inc. in the United States and other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model SVUA

August 2006 P/N ND211 Rev. A00

Getting Started With Your System 3

System Features

The major hardware and software features of your system include:

• One or two dual-core AMD Opteron 2000 Series processors.

• A minimum of 1 GB (single-processor systems) or 2 GB (dual-processor systems) of 667-MHz

registered DDR-II memory modules. Memory is upgradable to a maximum of 32 GB by installing

combinations of 512-MB, 1-GB, 2-GB, or 4-GB memory modules in the eight memory module sockets

on the system board.

• Support for either two 3.5-inch, internal SATA hard drives or two optional 3.5-inch, internal SAS hard

drives. (An optional SAS controller card is required for SAS hard-drive support. This optional SAS

controller also supports RAID levels 0 and 1.)

• An optional slimline IDE optical drive.

• An optional external USB diskette drive.

• A 600-W power supply.

• Four dual-rotor fan modules.

The system board includes the following features:

• One of the following riser card options:

–

A riser card supporting one x8 lane-width PCI-Express (PCIe) half-length expansion slot.

or

–

A riser card supporting one 3.3-V, 64-bit, 133-MHz PCI-X half-length expansion slot.

This PCI-X slot also supports legacy PCI expansion cards.

• Two integrated Gb Ethernet NICs, capable of supporting 10-Mbps, 100-Mbps, and 1000-Mbps data

rates.

• Four USB 2.0-compliant connectors (two on the system front panel and two on the back panel),

capable of supporting a diskette drive, an optical drive, a keyboard, a mouse, or a USB flash drive.

•

An integrated VGA-compatible video subsystem based on an integrated ATI RN50 PCI video

controller. The video subsystem includes a minimum of 16 MB of graphics memory and supports

various 2D graphics video modes. Maximum resolution is 1600x1200 with 65,536 colors.

• Systems management circuitry that monitors operation of the system fans as well as critical system

voltages and temperatures.

• Back-panel connectors including serial, video, two USB connectors, and two NIC connectors.

• Front-panel connectors including a video connector and two USB connectors.

For more information about specific features, see "Technical Specifications" on page 9.

4 Getting Started With Your System

Supported Operating Systems

Your system supports the following operating systems:

• Microsoft

®

Windows Server

®

2003 Standard and Web Editions

• Microsoft Windows Server 2003 x64 Edition

•Red Hat

®

Enterprise Linux ES and WS 4

• Red Hat Enterprise Linux ES and WS 4 for AMD64

•SUSE

®

Linux Enterprise Server 10 (when available)

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and regulatory information.

Warranty information may be included within this document or as a separate document.

• The

Rack Installation Guide

or

Rack Installation Instructions

included with your rack solution

describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system features and describes how to

troubleshoot the system and install or replace system components. This document may be found

on the CDs or DVDs that came with your system or at

support.dell.com

.

• CDs or DVDs included with your system provide documentation and tools for configuring

and managing your system.

• Updates are sometimes included with the system to describe changes to the system, software,

and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates first because they often

supersede information in other documents.

• Release notes or readme files may be included to provide last-minute updates to the system or

documentation or advanced technical reference material intended for experienced users or

technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not perform as expected,

see your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see www.dell.com/training for more information.

This service may not be offered in all locations.

Getting Started With Your System 5

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety instructions and important

regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time.

Unpacking the System

Unpack your system and identify each item. (Your system may not include the optional rack kit

and bezel shown here.)

Keep all shipping materials in case you need them later.

6 Getting Started With Your System

Installing the System in a Rack

Install the system in the rack once you have read the "Safety Instructions" located in the rack

installation documentation for your system.

See your rack installation documentation for instructions on installing your system in a rack.

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The back of your system has icons indicating the USB and video connectors. Be sure to tighten

the screws (if any) on the monitor's cable connector.

NOTE: If you simultaneously connect two monitors to the system, using the front and rear video connections,

the video output will default to the front connector because only one display can operate at a time.

Getting Started With Your System 7

Connecting the Power

Connect the system’s power cable to the system.

Routing the Power Cable through the Power Cable Retention Bracket

Bend the system power cable into a loop as shown in the illustration and secure the cable

using the cable retention bracket.

Plug the other end of the power cable into a grounded electrical outlet or a separate power source

such as an uninterruptible power supply (UPS) or a power distribution unit (PDU).

8 Getting Started With Your System

Turning on the System

Turn on the system and monitor (optional).

Press the power button on the system and the monitor. The power indicators should light.

Adjust the monitor's controls until the displayed image is satisfactory.

Installing the Optional Bezel

Install the bezel (optional).

Getting Started With Your System 9

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system documentation that ships

with your system. To install an operating system for the first time, see the Quick Installation Guide.

Be sure the operating system is installed before installing hardware or software not purchased with

the system.

Technical Specifications

Processor

Processor type One or two dual-core AMD Opteron 2000 Series processors

Expansion Bus

Bus type PCI-X, PCIe

Expansion slots via riser card: One x8 lane-width

PCIe slot

or

One 3.3-V, 64-bit, 133-MHz

PCI-X slot

Memory

Architecture 667-MHz DDR-II memory modules

Memory module sockets Eight 240-pin

Memory module capacities 512 MB, 1 GB, 2 GB, 4 GB

Minimum RAM 1 GB (one processor) or 2 GB (two processors)

Maximum RAM 32 GB

Drives

SATA hard drives One or two 3.5-inch drives

SAS hard drives One or two 3.5-inch drives

(requires optional SAS controller card)

Optical drive One optional slimline IDE CD-ROM, DVD-ROM/CD-RW

combination, or DVD-ROM

NOTE: DVD devices are data only

10 Getting Started With Your System

Connectors

Back Panel

NIC

Two RJ-45 (for two integrated 1-GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0 compliant

Video

15-pin VGA

Front Panel

Video

15-pin VGA

USB

Two 4-pin, USB 2.0 compliant

Video

Video type ATI RN50 video controller; VGA connector

Video memory Minimum of 16 MB

Resolution Maximum 2D graphics resolution: 1600 x 1200,

65,536 colors

Power

AC power supply (per power supply)

Wattage

600 W

Voltage

100–240 VAC, autoranging, 50/60 Hz, 6–4 A

Heat dissipation

1462 BTU/hr (maximum)

Maximum inrush current

Under typical line conditions and over the entire system

ambient operating range, the inrush current may reach 55 A

per power supply for 10 ms or less

System battery CR 2032 3.0-V lithium coin cell

Physical

Height 4.29 cm (1.67 in)

Width 42.55 cm (16.78 in)

Depth (including optional bezel) 64.8 cm (25.5 in)

Weight (maximum configuration) 14 kg (31 lb)

body.fm Page 10 Wednesday, August 30, 2006 11:30 AM

Getting Started With Your System 11

Environmental

NOTE: For additional information about environmental measurements for specific system configurations,

see www.dell.com/environmental_datasheets

Temperature

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

8% to 85% (noncondensing) with a maximum humidity

gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.25 G at 3–200 Hz for 15 min

Storage

0.5 G at 3–200 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse on each

side of the system) of 41 G for up to 2 ms

Storage

Six consecutively executed shock pulses in the positive

and negative x, y, and z axes (one pulse on each side of

the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

12 Getting Started With Your System

www.dell.com | support.dell.com

Dell™ PowerEdge™ SC1435 系统

系统使用入门

注、注意和警告

注：注表示可以帮助您更好地使用计算机的重要信息。

注意：注意表示可能会损坏硬件或导致数据丢失，并告诉您如何避免此类问题。

警告：警告表示可能会导致财产损失、人身伤害甚至死亡。

_________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

、

DELL

徽标和

PowerEdge

是

Dell Inc.

的商标；

Microsoft

和

Windows

是

Microsoft Corporation

的注册商

标，

Windows Server

是

Microsoft Corporation

的商标；

Red Hat

是

Red Hat, Inc.

的注册商标；

SUSE

是

Novell, Inc.

在美国和其它国

家／地区的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外

的其它商标和产品名称不拥有任何专有权。

型号：

SVUA

2006

年

8

月

P/N ND211

修订版

A00

系统使用入门 15

系统配置

系统的主要硬件和软件配置包括：

•

一个或两个双核心

AMD Opteron 2000

系列处理器。

•

至少

1 GB

（单处理器系统）或

2 GB

（双处理器系统）的

667 MHz

带寄存器的

DDR-II

内存模

块。通过在系统板上的八个内存模块插槽中安装

512 MB

、

1 GB

、

2 GB

或

4 GB

内存模块组合，

最大可将内存升级到

32 GB

。

•

支持两个

3.5

英寸内部

SATA

硬盘驱动器或两个可选的

3.5

英寸内部

SAS

硬盘驱动器。

（要支持

SAS

硬盘驱动器，需要一个可选的

SAS

控制器卡。该可选的

SAS

控制器还支持

RAID

级别

0

和级别

1

。）

•

一个可选的细长型

IDE

光盘驱动器。

•

一个可选的外部

USB

软盘驱动器。

•

一个

600 W

电源设备。

•

四个双转子风扇模块。

系统板包含以下配置：

•

以下提升卡选件之一：

-

支持一个

x8

信道宽度

PCI-Express (PCIe)

半长扩充槽的提升卡。

或

-

支持

3.3 V

、

64

位、

133 MHz PCI-X

半长扩充槽的提升卡。此

PCI-X

插槽还支持传统

PCI

扩充卡。

•

两个集成的千兆位以太网

NIC

，可以支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率。

•

四个

USB 2.0

兼容连接器（两个在系统前面板，两个在背面板），可以支持软盘驱动器、

光盘驱动器、键盘、鼠标或

USB

快擦写驱动器。

• 基于集成的

ATI RN50 PCI

视频控制器的

VGA

兼容集成视频子系统。此视频子系统包含至少

16 MB

的图形内存，并支持各种

2D

图形视频模式。最大分辨率为

1600 x 1200

（

65,536

色）。

•

系统管理电路，可监测系统风扇的运行以及系统临界电压和温度。

•

背面板连接器，包括串行连接器、视频连接器、两个

USB

连接器和两个

NIC

连接器。

•

前面板连接器，包括一个视频连接器和两个

USB

连接器。

有关特定配置的详细信息，请参阅第

21

页的“技术规格”。

16 系统使用入门

支持的操作系统

您的系统支持以下操作系统：

•

Microsoft

®

Windows Server

®

2003

标准版和

Web

版

•

Microsoft Windows Server 2003 x64 Edition

•

Red Hat

®

Enterprise Linux ES

和

WS 4

•

适用于

AMD64

的

Red Hat Enterprise Linux ES

和

WS 4

•

SUSE

®

Linux Enterprise Server 10

（可用时）

您可能需要的其它信息

警告：《产品信息指南》，提供了重要的安全信息和管制信息。保修信息可能包括在该说明文件中，

也可能作为单独的说明文件提供。

•

随机架解决方案附带的《机架安装指南》或《机架安装说明》，介绍了如何在机架中安装系统。

•

《硬件用户手册》提供了有关系统部件的信息，并介绍了如何排除系统故障以及如何安装或更换

系统组件。此说明文件可在随系统提供的

CD

或

DVD

中找到，或通过

support.dell.com

获得。

•

随系统附带的

CD

或

DVD

提供了用于配置和管理系统的说明文件和工具。

•

系统有时附带更新，用于说明对系统、软件和／或说明文件所做的更改。

注：请始终检查 support.dell.com 上的更新信息并首先进行阅读，因为该网站上的信息常常会取代其

它说明文件中的信息。

•

系统可能附带版本注释或自述文件，以提供系统或说明文件的最新更新内容，或者为有经验的用

户或技术人员提供高级技术参考资料。

获得技术帮助

如果您对本指南中的步骤有疑问，或系统运行无法达到预期效果，请参阅《硬件用户手册》。

Dell

可以提供企业培训与认证；有关详情，请访问

www.dell.com/training

。并非在所有国家和地区

均可提供此服务。

系统使用入门 17

安装和配置

警告：在执行以下过程之前，请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。

本节介绍初次安装系统时的步骤。

打开系统包装

打开系统包装并识别每项物品。（您的系统可能不包括此处显示的可选机架套件和挡板。）

妥善保管好所有运输包装材料，以备将来使用。

18 系统使用入门

将系统安装在机架中

在仔细阅读了系统的机架安装说明文件中的“安全说明”之后，在机架中安装系统。

有关在机架中安装系统的说明，请参阅机架安装说明文件。

连接键盘、鼠标和显示器

连接键盘、鼠标和显示器（可选）。

系统背面具有表示

USB

连接器和视频连接器的图标。确保拧紧显示器的电缆连接器

上的螺钉（如果有）。

注：如果使用前面和后面的连接器同时将两台显示器连接至系统，视频输出将默认使用

前面的连接器，因为一次仅能有一台显示器工作。

Page is loading ...

Dell PowerEdge SC1435 Quick start guide

Dell PowerEdge SC1435 Quick start guide

in other languages

Related papers