Dell PowerEdge 860 Quick start guide

Type
Quick start guide
www.dell.com | support.dell.com
Dell™ PowerEdge™ 860 Systems
Getting Started
With Your System
系统使用入门
はじめに
시스템시작하기
Model SVP
GJ053fc0.fm Page 1 Wednesday, June 21, 2006 3:58 PM
www.dell.com | support.dell.com
Dell™ PowerEdge™ 860 Systems
Getting Started
With Your System
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2006 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Intel, Pentium, and Celeron are registered
trademarks and Core is a trademark of Intel Corporation; Microsoft, Windows, and Windows Server are registered trademarks of Microsoft
Corporation; Red Hat is a registered trademark of Red Hat, Inc.; SUSE is a registered trademark of Novell,Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model SVP
June 2006 P/N GJ053 Rev. A00
Getting Started With Your System 3
System Features
The major hardware and software features of your system include:
1U/1S rack-mountable chassis with support for static rails and sliding rails.
NOTE: Use the System Setup program to view processor information. See "Using the System Setup
Program" in your Hardware Owner’s Manual.
One of the following processors:
One Intel
®
Core™ 2 Duo
One Intel Celeron
®
D, 300 Sequence
One Intel Pentium
®
4, 600 Sequence
A minimum of 512 MB of 533-MHz or 667-MHz DDR2 SDRAM memory, upgradable to a
maximum of 8 GB by installing combinations of 512-MB, 1-GB, or 2-GB unbuffered ECC
memory modules in four memory module sockets on the system board.
One of the following riser card options:
One full-height, half-length, x8 lane PCIe expansion slot and one full-height, half-length
PCIe expansion slot with a x8 connector but with a x4 lane capability.
One full-height, half-length, 133MHz/64 bit PCI-X expansion slot and one full-height, half-
length, x8 lane PCIe expansion slot, which includes a connector for an optional remote access
controller (RAC) card.
One 3.5-inch CD, DVD, or combination CD-RW/DVD in a peripheral drive bay.
Support for the following internal hard-drive configurations:
Up to two internal, 1-inch high, SATA hard drives with the integrated drive controllers.
Up to two internal, 1-inch high optional Serial-Attached SCSI (SAS) hard drives with an
optional SAS controller card.
Optional remote access controller for remote systems management. This option requires a riser
card with support for PCI-X and PCIe RAC connectors.
Optional USB flash drive emulates a diskette drive or hard drive.
One 345-W power supply.
Two integrated Gigabit Ethernet network adapters, capable of supporting 10-Mbps, 100-Mbps,
and 1000-Mbps data rates.
4 Getting Started With Your System
Two system cooling fans, one power-supply cooling fan, and one optional PCI fan for systems with
a SAS/RAID controller.
Serial connector for console redirection support.
Security features, including chassis-intrusion detection and keylock on the optional bezel.
Systems management circuitry that monitors critical system voltages and temperatures, and works in
conjunction with the systems management software.
Back-panel connectors include keyboard, video, mouse, serial, two USB, and two NIC connectors.
Front-panel connectors include one VGA and two USB connectors. For more information about
specific features, see "Technical Specifications" on page 9.
The following software is included with your system:
A System Setup program for quickly viewing and changing system configuration information. For more
information on this program, see "Using the System Setup Program" in the
Hardware Owner’s Manual
.
Enhanced security features, including a system password and a setup password, available through the
System Setup program.
Video drivers for displaying many popular application programs in high-resolution modes.
Systems management software and documentation CDs.
Supported Operating Systems
Microsoft Windows Server
2003, Standard Edition and Web Edition
Microsoft Windows Server 2003, Standard Edition 64-Bit
•Red Hat
®
Enterprise Linux ES (versions 3 and 4) for Intel x86
Red Hat Enterprise Linux ES (version 4) for Intel Extended Memory 64 Technology (Intel EM64T)
•SUSE
®
Linux Enterprise Server 9 (Service Pack 2 or later) for Intel EM64T
•SUSE
®
Linux Enterprise Server 10 for Intel EM64T
Other Information You May Need
CAUTION: The Product Information Guide provides important safety and regulatory information. Warranty
information may be included within this document or as a separate document.
The
Rack Installation Instructions
or
Rack Installation Guide
included with your rack solution
describes how to install your system into a rack.
The
Hardware Owner’s Manual
provides information about system features and describes how to
troubleshoot the system and install or replace system components. The
Hardware Owner’s Manual
is available on the CDs that came with your system or on
support.dell.com
.
CDs included with your system provide documentation and tools for configuring and managing
your system.
Getting Started With Your System 5
Systems management software documentation describes the features, requirements, installation,
and basic operation of the software.
Operating system documentation describes how to install (if necessary), configure, and use the
operating system software.
Documentation for any components you purchased separately provides information to configure
and install these options.
Updates are sometimes included with the system to describe changes to the system, software,
and/or documentation.
NOTE: Always check for updates on support.dell.com and read the updates first because they often
supersede information in other documents.
Release notes or readme files may be included to provide last-minute updates to the system or
documentation or advanced technical reference material intended for experienced users or
technicians.
Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system does not perform as expected,
see your Hardware Owner’s Manual.
Dell Enterprise Training and Certification is available; see www.dell.com/training for more information.
This service may not be offered in all locations.
Installation and Configuration
CAUTION: Before performing the following procedure, read and follow the safety instructions and important
regulatory information in your Product Information Guide.
This section describes the steps to set up your system for the first time.
CAUTION: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift
the system by yourself.
6 Getting Started With Your System
Unpacking the System
Unpack your system and identify each item.
Keep all shipping materials in case you need them later.
Installing the Rails and System in a Rack
Once you have read the "Safety Instructions" located in the rack installation documentation
for your system, install the rails and the system in the rack.
See your rack installation documentation for instructions on installing your system in a rack.
Getting Started With Your System 7
Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable to plug into
each connector. Be sure to tighten the screws (if any) on the monitor's cable connector.
Connecting the Power
Connect the system’s power cable(s) to the system. Attach the cable retention clip to the back
of the system, run the cable through the cable retention clip as shown, and close the clip.
Plug the other end of the cable into a grounded electrical outlet or a separate power source
such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).
8 Getting Started With Your System
Turning on the System
Turn on the system and monitor (optional).
Press the power button on the system and the monitor. The power indicators should light.
Adjust the monitor’s controls until the displayed image is satisfactory.
Installing the Bezel
Install the bezel (optional).
Getting Started With Your System 9
Complete the 0perating System Setup
If you purchased a preinstalled operating system, see the operating system documentation that ships
with your system. To install an operating system for the first time, see the
Quick Installation Guide
.
Be sure the operating system is installed before installing hardware or software not purchased with
the system.
Technical Specifications
Processor
Processor type One
Intel
®
Core
2 Duo
processor
or
One Intel Celeron
®
D, 300 Sequence processor
or
One Intel Pentium
®
4, 600 Sequence processor
Front-side bus speed
Intel Celeron D
533 MHz minimum
Intel Pentium 4
800 MHz minimum
Intel Core 2 Duo
1066 MHz minimum
Internal cache
Intel Celeron D
256 KB
Intel Pentium 4
at least 2 MB
Intel Core 2 Duo
at least 2 MB
Expansion Buses
Bus type PCI-X, PCIe
Expansion slots - Two optional riser cards
Riser 1
PCIe
One full-height, half-length, x8 lane PCIe slot
PCIe
One full-height, half-length x4 lane PCIe slot
residing on a x8 lane connector
10 Getting Started With Your System
Riser 2
PCI-X One full-height, half-length,
64-bit, 133MHz PCI-X slot
PCIe One full-height, half-length, x8 lane PCIe slot
Memory
Architecture Up to four unbuffered DDR2 533/667 MHz
SDRAM memory modules with ECC
Memory module sockets Four 240-pin
Memory module capacities 512 MB, 1 GB, or 2 GB
Minimum RAM 512 MB (one 512-MB module)
Maximum RAM 8 GB
Drives
Hard Drives
SATA Up to two 1-inch high drives
SAS Up to two optional internal 1-inch high drives
with optional SAS controller card
Optical drive CD, DVD, or combination CD-RW/DVD in a
peripheral drive bay
NOTE: DVD devices are data only.
USB flash drive One optional drive that emulates a diskette drive
or hard drive
Connectors
Externally accessible
Back
Network adapter Two RJ-45 (for integrated 1-Gigabit network
adapters)
PS/2-style keyboard 6-pin mini-DIN
PS/2-compatible mouse 6-pin mini-DIN
Serial 9 pin
USB Two 4-pin, USB 2.0 compliant
Video 15-pin VGA
Expansion Buses (continued)
Getting Started With Your System 11
Front
Video 15-pin VGA
USB Two 4-pin, USB 2.0 compliant
Internally accessible
IDE channel 40 pin
SATA channels Two 7 pin
Video
Video type Integrated ATI RN50 VGA controller
Video memory 16 MB, 32MB when available
Power
AC power supply
Wattage 345 W
Voltage 100–240 VAC, 50/60 Hz
Maximum inrush current Under typical line conditions and over the entire
system ambient operating range, the inrush current
may reach 25 A for 10 ms or less.
System battery
CR 2032 3.0-V lithium coin cell
Physical
Height 4.2 cm (1.68 in)
Width
44.6 cm (17.6 in)
Depth
With optional bezel 57.6 cm (22.7 in)
Without optional bezel 54.6 cm (21.5 in)
Weight (maximum configuration) 11.8 kg (26 lb)
Connectors (continued)
12 Getting Started With Your System
Environmental
NOTE: For additional information about environmental measurements for specific system configurations,
see www.dell.com/environmental_datasheets.
Temperature
Operating 10° to 35°C (50° to 95°F)
Storage –40° to 65°C (–40° to 149°F)
Relative humidity
Operating 20% to 80% (noncondensing) with a maximum
humidity gradation of 10% per hour
Storage 5% to 95% (noncondensing)
Maximum vibration
Operating 0.26 G at 5–350 Hz for 15 min
Storage 1.54 G at 10–250 Hz for 15 min
Maximum shock
Operating One shock pulse in the positive z axis (one pulse on
each side of the system) of 31 G for up to 2.6 ms
Storage Six consecutively executed shock pulses in the
positive and negative x, y, and z axes (one pulse
on each side of the system) of 71 G for up to 2 ms
Altitude
Operating –16 to 3048 m (–50 to 10,000 ft)
Storage –16 to 10,600 m (–50 to 35,000 ft)
www.dell.com | support.dell.com
Dell™ PowerEdge™ 860 系统
系统使用入门
注、注意和警告
注:注表示可以帮助您更好地使用计算机的重要信息。
注意:
注意表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。
警告:
警告表示可能会导致财产损失、人身伤害甚至死亡。
____________________
本说明文件中的信息如有更改,恕不另行通知。
© 2006 Dell Inc.
版权所有,翻印必究。
未经
Dell Inc.
书面许可,严禁以任何形式进行复制。
本文中使用的商标:
Dell
DELL
徽标和
PowerEdge
Dell Inc.
的商标;
Intel
Pentium
Celeron
Intel Corporation
的注册商
标,
Core
Intel Corporation
的商标;
Microsoft
Windows
Windows Server
Microsoft Corporation
的注册商标;
Red Hat
Red Hat, Inc.
的注册商标;
SUSE
Novell,Inc.
的注册商标。
本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。
Dell Inc.
对本公司的商标和产品名称之外
的其它商标和产品名称不拥有任何专有权。
型号:
SVP
2006
6
P/N GJ053
修订版
A00
系统使用入门 15
系统配置
系统的主要硬件和软件配置包括:
支持静态滑轨和滑动滑轨的
1U/1S
机架可固定机箱。
注:使用系统设置程序可以查看处理器信息。请参阅《硬件用户手册》中的
“使用系统设置程序”。
以下处理器之一:
一个
Intel
®
Core™ 2 Duo
一个
Intel Celeron
®
D
300
序列
一个
Intel Pentium
®
4
600
序列
至少
512 MB
533 MHz
667 MHz DDR2 SDRAM
内存,通过在系统板上的四个内存模块
插槽中安装
512 MB
1 GB
2 GB
非缓冲
ECC
内存模块组合,最多可升级至
8GB
以下提升卡选件之一:
一个全高、半长、
x8
信道
PCIe
扩充槽和一个全高、半长扩充槽 (带
x8
连接器,但支持
x4
信道)
一个全高、半长、
133MHz/64
PCI-X
扩充槽和一个全高、半长、
x8
信道
PCIe
扩充槽,
其中包括一个用于连接可选远程访问控制器
(RAC)
卡的连接器。
一个
3.5
英寸
CD
DVD
或组合
CD-RW/DVD
(位于外围设备驱动器托架中)。
支持以下内部硬盘驱动器配置:
通过集成的驱动器控制器,最多可支持两个内部
1
英寸高
SATA
硬盘驱动器。
通过可选的
SAS
控制器卡,最多可支持两个内部
1
英寸高可选串行连接
SCSI (SAS)
硬盘
驱动器。
可选的远程访问控制器,用于远程系统管理。此选项需要支持
PCI-X
PCIe RAC
连接器的
提升卡。
可选的
USB
快擦写驱动器,可以仿真软盘驱动器或硬盘驱动器。
一个
345 W
电源设备。
两个集成千兆位以太网网络适配器,可以支持
10 Mbps
100 Mbps
1000 Mbps
数据速率。
两个系统冷却风扇、一个电源设备冷却风扇,以及一个可选的
PCI
风扇(用于具有
SAS/RAID
控制器的系统)。
串行连接器,用于支持控制台重定向。
安全保护功能部件,包括机箱防盗检测功能和可选挡板上的键锁。
系统管理电路,可监测系统临界电压和温度,以及与系统管理软件配合工作。
16 系统使用入门
背面板连接器包括键盘连接器、视频连接器、鼠标连接器、串行连接器、两个
USB
连接器和两
NIC
连接器。
前面板连接器包括一个
VGA
连接器和两个
USB
连接器。有关特定配置的详细信息,
请参阅第
21
页的“技术规格”。
您的系统附带以下软件:
系统设置程序,用于快速查看和更改系统配置信息。有关此程序的详情,请参阅
《硬件用户手册》中的“使用系统设置程序。”
增强的安全保护功能,包括系统密码和设置密码,可通过系统设置程序进行设置。
视频驱动程序,用于以高分辨率模式显示多种常见应用程序。
系统管理软件和说明文件
CD
支持的操作系统
Microsoft Windows Server
2003
,标准版和
Web
Microsoft Windows Server 2003
标准版(
64
位)
适用于
Intel x86
Red Hat
®
Enterprise Linux ES
(第
3
版和第
4
版)
适用于
Intel 64
位扩展内存技术
(Intel EM64T)
Red Hat Enterprise Linux ES
(第
4
版)
适用于
Intel EM64T
SUSE
®
Linux Enterprise Server 9
Service Pack 2
或更高版本)
用于
Intel EM64T
SUSE
®
Linux Enterprise Server 10
您可能需要的其它信息
警告:《产品信息指南》,提供了重要的安全信息和管制信息。保修信息可能包括在该说明文件中,
也可能作为单独的说明文件提供。
随机架解决方案附带的《机架安装说明》或《机架安装指南》,介绍了如何在机架中安装系统。
《硬件用户手册》提供了有关系统部件的信息,并介绍了如何排除系统故障以及如何安装或更换
系统组件。《硬件用户手册》可在随系统提供的
CD
或在
support.dell.com
上获得。
随系统附带的
CD
提供了用于配置和管理系统的说明文件和工具。
系统管理软件说明文件,介绍了软件的功能、要求、安装和基本操作。
操作系统说明文件,介绍了如何安装(如果有必要)、配置和使用操作系统软件。
单独购买的任何组件所附带的说明文件,提供了有关配置和安装这些选件的信息。
系统有时附带更新,用于说明系统、软件和或说明文件所的更改。
注:请始终检查
support.dell.com
上的更新信息并首先进行阅读,因为该网站上的信息常常会取代其
它说明文件中的信息。
系统可能附带版本注释自述文件,以提供系统或说明文件的最新更新内,或者为经验的用
户或技术人员提供高级技术参考资料
系统使用入门 17
获得技术帮助
如果您本指南中的步骤问,或系统无法达到预期效果,请参阅《硬件用户手册》。
Dell
可以提供企业培训认证;有关详情,请访问
www.dell.com/training
。并非在所有国家地区均
可提供此服务
安装和配置
警告:在执行以下过程之前,请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。
介绍初次安装系统时的步骤
警告:无论何时您需要抬起系统,均需找他人协助。为了避免造成伤害,请勿尝试自行抬起系统。
打开系统包装
打开系统包装并识别每物品
妥善保管所有运输包装材料,以备将来使用。
18 系统使用入门
在机架中安装滑轨和系统
细阅了系统的机架安装说明文件中的 “安全说明”之,在机架中安装滑轨和系统。
有关在机架中安装系统的说明,请参阅机架安装说明文件。
连接键盘、鼠标和显示器
连接键盘、鼠标和显示器 (可选)
系统背面的连接器附有标,这些标指示了要插入每个连接器的电拧紧显示
器的电连接器上的螺钉 (如果有)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Dell PowerEdge 860 Quick start guide

Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI