Paradise Datacom High Power Outdoor PowerMAX Systems Owner's manual

Outdoor PowerMAX Systems

High Power Outdoor SSPA Modules

C-Band System Installation Manual

215861 REV E ECO A26179 8/2022

Teledyne Paradise Datacom (814) 238-3450

11361 Sunrise Park Drive sales@paradisedata.com

Rancho Cordova, CA 95742 USA www.paradisedata.com

2 215861 REV E Installation, Outdoor HPO PowerMAX System

Teledyne Paradise Datacom, a division of Teledyne Defense Electronics LLC, is a single source for high

power solid state amplifiers (SSPAs), Low Noise Amplifiers (LNAs), Block Up Converters (BUCs), and

Modem products. Operating out of two primary locations, Rancho Cordova, CA, USA and

Chelmsford, England, Teledyne Paradise Datacom has more than a 20 year history of providing innova-

tive solutions to enable satellite uplinks, battlefield communications, and cellular backhaul.

Teledyne Paradise Datacom Teledyne Paradise Datacom Ltd.

11361 Sunrise Park Drive 106 Waterhouse Lane,

Rancho Cordova, CA 95742 USA Chelmsford, Essex, England, CM1 2QU

(814) 238-3450 Tel: +44(0)1245 847520

Information in this document is subject to change without notice. The latest revision of this document

may be downloaded from the company web site: http://www.paradisedata.com.

Use and Disclosure of Data

This product is classified as EAR99 and is subject to U.S. Department of Commerce regulations. Export,

reexport or diversion contrary to U.S. law is prohibited.

Proprietary and Confidential

The information contained in this document is the sole property of Teledyne Paradise Datacom. Any re-

production in part or as a whole without the written permission of Teledyne Paradise Datacom is prohib-

ited.

All other company names and product names in this document are property of the respective compa-

nies.

Data Security

Teledyne Paradise Datacom amplifiers and controllers do not inherently provide encryption to transmit-

ted data, and have limited security measures to protect it. If the unit will be accessible over the Internet,

exercise appropriate data security protocols. Teledyne Paradise Datacom strongly recommends placing

the equipment behind a protective Firewall or setting up a VPN link with dual authentication for remote

access.

Printed in the USA

Installation, Outdoor HPO PowerMAX System 215861 REV E 3

Table of Contents

Section 1: Introduction................................................................................................ 7

1.0 Introduction ................................................................................................... 7

1.1 Inspection and Unpacking ............................................................................. 7

1.2 Installation Conventions ................................................................................ 7

Section 2: Installation, 8-Way System ....................................................................... 9

2.0 Introduction ................................................................................................... 9

2.1 Installation ..................................................................................................... 9

2.1.1 Prepare Location Decking ............................................................. 11

2.1.2 Install System Frame .................................................................... 13

2.1.3 Install Waveguide/Combiner Arrays .............................................. 14

2.1.4 Install High Power Outdoor SSPA Modules .................................. 15

2.1.5 Install Magic Tee/Termination ....................................................... 17

2.1.5.1 Connect Dual Crossguide Coupler .................................. 17

2.1.5.2 Connect Flexible Waveguide .......................................... 18

2.1.6 Install Optional Maintenance Switch ............................................. 19

2.1.6.1 Check Installation of Optional Maint. Sw. Termination .... 19

2.1.6.2 Install Optional Maintenance Switch W/G Assy ............... 19

2.1.6.3 Install Optional Maintenance Switch Controller ............... 20

2.1.7 Optional AC Distribution Box ......................................................... 21

2.1.8 RF Distribution Box ....................................................................... 21

2.1.9 Outdoor Controllers ....................................................................... 21

2.1.10 Connect Cables ........................................................................... 22

2.1.10.1 Forward Sample In ........................................................ 22

2.1.10.2 Reflected Sample In ...................................................... 22

2.1.10.3 RF Distribution Cables ................................................... 22

2.1.10.4 Auxiliary Power Cable (L213830-7 or L213830-1) ......... 23

2.1.10.5 SSPA Module M&C Cables (L213827-1, -2) ................. 24

2.1.10.6 Outdoor Controller DC Input Cables (L213826-1, -2) .... 25

2.1.10.7 System Link Cable (L213828-1) .................................... 26

2.1.10.8 Optional Ethernet Cables .............................................. 26

2.1.10.9 Optional Mute Switch Cable ......................................... 27

2.3 Weatherize Cable Connections .................................................................. 28

Section 3: Installation, 16-Way System ................................................................... 29

3.0 Introduction ................................................................................................. 29

3.1 Installation ................................................................................................... 29

3.1.1 Prepare Location Decking ............................................................. 31

3.1.2 Install System Framework ............................................................. 33

3.1.2.1 Install Optional Maintenance Termination Supports ........ 33

3.1.2.2 Install Optional Maintenance Termination ....................... 33

3.1.2.3 Install Output Magic Tee Termination Supports............... 34

3.1.2.4 Install Output Magic Tee Termination .............................. 34

3.1.2.5 Install Uni-Strut Supports (99 Inch).................................. 35

3.1.2.6 Install System Termination Lower Uni-Strut (45 Inch) ..... 36

3.1.2.7 Install System RF Distribution Upper Uni-Strut (45 Inch) . 37

3.1.2.8 Install System Termination Upper Uni-Strut (45 Inch) ..... 38

4 215861 REV E Installation, Outdoor HPO PowerMAX System

3.1.2.9 Install System Termination Support Uni-Strut ................ 39

3.1.3 Install Waveguide/Combiner Arrays .............................................. 40

3.1.4 Install High Power Outdoor SSPA Modules .................................. 40

3.1.5 Install 8-Way Output Magic Tees and Terminations ..................... 40

3.1.6 Install System Termination ............................................................ 41

3.1.7 Install 16-Way Magic Tee Assembly ............................................. 42

3.1.8 Install 8-Way RF Output Waveguide ............................................. 43

3.1.9 Install System RF Distribution Box Assembly ............................... 44

3.1.9.1 Optional Ethernet Switch ................................................. 44

3.1.10 Install Optional AC Distribution Boxes ........................................ 45

3.1.11 Install RF Distribution Boxes ....................................................... 45

3.1.12 Install Outdoor Controllers .......................................................... 45

3.1.13 Connect Cables .......................................................................... 46

3.1.13.1 Forward Sample In ........................................................ 46

3.1.13.2 RF Distribution Cables .................................................. 46

3.1.13.3 Forward/Reflected Power Sample Cables ..................... 46

3.1.13.4 Auxiliary Power Cable (L213830-8 or L213830-9) ........ 47

3.1.13.5 SSPA Module M&C Cables (L213827-1, -2) ................. 48

3.1.13.6 Mute Signal Jumper Cable (L215836-1) ........................ 48

3.1.13.7 Outdoor Controller DC Input Cables (L213826-1, -2) .... 49

3.1.13.8 System Link Cable (L213828-4) .................................... 50

3.1.13.9 Optional Ethernet Cables .............................................. 50

3.2 Install Optional Maintenance Switch ........................................................... 51

3.2.1 Install Optional Maintenance Switch Controller ............................. 51

3.2.2 Install Optional Maintenance Switch ............................................ 51

3.2.3 Install Optional Maintenance Termination Supports ...................... 52

3.2.4 Install Optional Maintenance Termination ..................................... 53

3.2.5 Install Optional Maintenance Waveguide ...................................... 54

3.2.6 Optional Mute Switch Cable (L215628-3) ..................................... 55

3.3 Weatherize Cable Connections .................................................................. 56

Appendix A ................................................................................................................ 57

Installation, Outdoor HPO PowerMAX System 215861 REV E 5

Figures

Figure 2-1: System Components, 8-Way System, as Shipped ......................... 10

Figure 2-2: Installation, Base Mounting and Anchor Points, 8-way System ...... 11

Figure 2-3: System Outline with Optional Maint. Switch, Top View ................. 12

Figure 2-4: System Outline, System RF Output End View ............................... 12

Figure 2-5: Install Waveguide/Combiner Arrays to Frame (System 1 shown) . 14

Figure 2-6: Install SSPAs into Frame ............................................................... 15

Figure 2-7: Loosely Bolt SSPA to Frame ......................................................... 16

Figure 2-8: Fasten SSPA Waveguide Flanges ................................................. 16

Figure 2-9: Install Dual Crossguide Coupler ..................................................... 17

Figure 2-10: Install Flex Waveguide ................................................................. 18

Figure 2-11: Install Optional Maintenance Switch Waveguide Assembly ......... 19

Figure 2-12: System Auxiliary Power Cable, L213830-1 or L213830-7 ............ 23

Figure 2-13: SSPA Module M&C Cable, L213827-1/-2 .................................... 24

Figure 2-14: Outdoor SSPA Controller DC Input Cable, L213826-1/-2 ............. 25

Figure 2-15: System Link Cable, L213828-1 .................................................... 26

Figure 2-16: Optional Ethernet Cables, L213824-1 .......................................... 26

Figure 2-17: Optional Mute Switch Cable ......................................................... 27

Figure 2-18: Install Cable Bracket to Uni-strut Frame ....................................... 27

Figure 2-19: Maintenance Switch Controller Cable .......................................... 28

Figure 3-1: System Components, 16-Way System .......................................... 30

Figure 3-2: Installation, Base Mounting and Anchor Points, 16-way System .... 31

Figure 3-3: Installation, 16-way System, Top View ........................................... 32

Figure 3-4: Installation, Magic Tee Termination Supports ................................ 34

Figure 3-5: Attach Termination to Support ........................................................ 34

Figure 3-6: Connect 99-inch Uni-Strut Between 8-Way Systems ..................... 35

Figure 3-7: Mounting Hardware, 99-inch Uni-Strut Segments .......................... 35

Figure 3-8: Installation, System Termination, Lower Uni-Strut Support ............ 36

Figure 3-9: Installation, Magic Tee Termination Lower Support Bracket .......... 36

Figure 3-10: Installation, System Controller Upper Uni-Strut Support............... 37

Figure 3-11: Installation, System Termination Upper Support Uni-Strut (x2) .... 38

Figure 3-12: Installation, System Termination Support Uni-Strut Assemblies... 39

Figure 3-13: Installation, System Termination, Upper View .............................. 41

Figure 3-14: Installation, System Termination, Lower View .............................. 41

Figure 3-15: Installation, 16-Way Magic Tee Assembly .................................... 42

Figure 3-16: Installation, 8-Way RF Output Waveguide.................................... 43

Figure 3-17: Installation, System Signal Box Assembly .................................... 44

Figure 3-18: Auxiliary Power Cable, L213830-8 or L213830-9 ......................... 47

Figure 3-19: SSPA Module M&C Cable, L213827-1/-2 .................................... 48

Figure 3-20: Mute Signal Jumper Cable, L215836-1 ........................................ 48

Figure 3-21: Outdoor SSPA Controller DC Input Cable, L213826-1/-2 ............. 49

Figure 3-22: System Link Cable, L213828-4 .................................................... 50

Figure 3-23: Ethernet Cables, L213824-X ........................................................ 50

Figure 3-24: Installation, Optional Maintenance Termination Supports ............ 51

Figure 3-25: Installation, Optional Maintenance Termination............................ 52

Figure 3-26: Installation, Optional Maintenance Switch .................................... 53

Figure 3-27: Installation, Optional Maintenance Waveguide............................. 54

Figure 3-28: Mute Switch Cable, L215628-3 .................................................... 55

Figure 3-29: Installation, Maintenance Switch Cable Mounting Bracket ........... 55

Figure 3-30: Maintenance Switch Controller Cable .......................................... 56

6 215861 REV E Installation, Outdoor HPO PowerMAX System

Tables

Table 2-1: RF Distribution Cable Connections, 8-way System ......................... 22

Table 3-1: RF Distribution Cable Connections, 16-way System ....................... 46

Table A-1: Maximum Hardware Torque Specifications .................................... 57

Installation, Outdoor HPO PowerMAX System 215861 REV E 7

1.0 Scope

This manual contains the installation instructions for a C-Band High Power Outdoor

PowerMAX System, in configurations of 8-module and 16 module arrays.

1.1 Inspection and Unpacking

When the system is received, an initial inspection should be completed. First, ensure

that the shipping containers are not damaged. If any damage is discovered, have a

representative of the shipping company present when the container is opened.

Perform a visual inspection of the equipment to make sure that all items on the packing

list are enclosed. If any damage has occurred or if items are missing, contact:

Teledyne Paradise Datacom

11361 Sunrise Park Drive

Rancho Cordova, CA 95742 USA

Phone: 1 (814) 238-3450

Save all shipping containers and packing materials for future use.

1.2 Installation Conventions

The High Power Outdoor PowerMAX system was shipped from the factory as intact as

possible. The following conventions should be observed when preparing to install your

system.

1.2.1 System Frame

The High Power Outdoor PowerMAX system frame is a welded steel assembly with

steel supports bolted in place. A rain shield is bolted to the top of the frame.

When possible, some of the system components may be shipped in place, affixed to

the frame. Cables may be shipped connected to the components, with the loose ends

zip-tied to the frame.

Before beginning installation, the user should inspect the frame and any attached com-

ponents. Ensure that all connecting hardware is fastened securely.

1.2.2 Solid State Power Amplifier Modules

SSPA modules are typically packaged individually in boxes, which are subsequently

packaged in shipping crates. An identification label is affixed to each SSPA module.

When it comes time to install the SSPA modules, match this label with the label on the

system frame, and install the module into that position in the frame.

Section 1: Introduction

8 215861 REV E Installation, Outdoor HPO PowerMAX System

1.2.3 RF Distribution Boxes and Outdoor System Controllers

An identification label is affixed to the RF Distribution Boxes and Outdoor System Con-

trollers. In 16-module systems, make sure to use the items labeled “System 1” with

SSPA modules S1.X.X, and the items labeled “System 2” with SSPA modules S2.X.X.

1.2.4 Optional AC Distribution Boxes

An identification label is affixed to the AC Distribution Boxes. In 16-module systems,

make sure to use the AC Distribution Box labeled “System 1” with SSPA modules

S1.X.X, and the AC Distribution Box labeled “System 2” with SSPA modules S2.X.X.

1.2.5 Waveguide Combiner Arrays

The waveguide combiner arrays for each 4-module system were shipped intact in foam

insulated boxes, which are subsequently packaged in shipping crates. All connecting

waveguide and any optional maintenance switch array and termination that may be in-

cluded in the system are likewise packaged.

Each waveguide combiner array is identified with a label corresponding with the top

SSPA module to which it will be connected.

All open waveguide flanges are covered for shipment, either with plastic covers, or with

Kapton tape. Keep these covers in place to help prevent debris from falling into an

open waveguide. Remove the cover or tape before connecting waveguide flanges to-

gether.

A set of half gaskets and full gaskets were shipped with the system. Make sure to in-

stall these gaskets between waveguide flanges as prompted in the instructions.

1.2.6 Control and Communication Cable Assemblies

The control and communication cable assemblies are shipped in place and are typical-

ly zip-tied to the frame. Untrimmed zip-ties are used to temporarily tie down cables dur-

ing shipment, and these untrimmed zip-ties may be cut as needed during installation.

Zip-ties that are trimmed should not be cut, unless the cable being tied down needs to

be removed from the system.

1.2.7 Semi-Rigid Coaxial Cables

All semi-rigid coaxial cables are pre-formed at the factory for best fit into the system.

Do not bend or otherwise alter the form of these cables. Each coaxial cable is identified

with a label, and should be installed as prompted in the instructions.

1.2.8 Installation Hardware

Where possible, the hardware used to install the various system components was

shipped in place on the frame. If a component was not shipped in place, the hardware

will need to be removed, saved and re-used when installing the component. Refer to

Appendix A for torque values.

Installation, Outdoor HPO PowerMAX System 215861 REV E 9

2.0 Introduction

This section describes the unpacking, inspection and installation procedures the user

should follow to set up a 8-way C-Band High Power Outdoor PowerMAX System.

2.1 Installation

The system was shipped from the factory as intact as possible, but some assembly is

required to complete the installation. The system includes the following components:

 (1) Welded 8-Way Frame with supports and rain shield;

 (8) High Power Outdoor SSPA Modules;

 (2) Outdoor SSPA Controller Assemblies (shipped installed in frame);

 (1) RF Distribution Box Assembly (shipped installed in frame);

 (2) Waveguide/Combiner Assemblies;

 (1) Magic Tee Assembly and Termination (shipped installed in frame);

 (1) Optional AC Distribution Box Assembly (shipped installed in frame);

 (1) Optional Maintenance Switch Controller;

 (1) Optional Maintenance Switch and Termination (Load shipped installed

in frame)

 (1) Optional Outdoor Ethernet Switch (attached to Controller Assembly);

 Coaxial cables and COMS cables.

See Figure 2-1 on the following page.

When securing all hardware during installation, refer to Appendix A for hardware

torque values.

Section 2: Installation, 8-Way System

10 215861 REV E Installation, Outdoor HPO PowerMAX System

Figure 2-1: System Components, 8-Way System, as Shipped

Switch Controller and Cable Assembly

Optional Maintenance Switch Components

Welded steel frame with AC Distribution box, RF Distribution box, System Controllers

and dummy loads installed. Loose ends of cables zip-tied to frame.

W/G Assy (x2) Crossguide & Flex W/G Maintenance

Switch

W/G Assy

High Power Outdoor

SSPA (X8)

Installation, Outdoor HPO PowerMAX System 215861 REV E 11

2.1.1 Prepare Location Decking

The Outdoor PowerMAX System is designed to be installed on a flat, level, solid sur-

face with the capability of anchoring the uni-strut frame assemblies to the decking.

Figure 2-2 shows the typical dimensions of the base mounting installation and

anchor points for the system. An outline drawing specific to your system will be includ-

ed with your system.

The RF Distribution Box and Outdoor Controllers are mounted on the frame opposite

the RF Output. The optional AC Distribution Box is mounted at the top of the frame.

The indoor controller for the optional Maintenance Switch requires installation in a cli-

mate controlled environment.

Figure 2-2: Installation, Base Mounting and Anchor Points, 8-way System

12 215861 REV E Installation, Outdoor HPO PowerMAX System

Figure 2-3 shows the top view of the system, after installation is completed.

Figure 2-4 shows the system RF Output end view of the fully-installed system.

Figure 2-4: System Outline, System RF Output End View

Figure 2-3: System Outline with Optional Maintenance Switch, Top View

Installation, Outdoor HPO PowerMAX System 215861 REV E 13

2.1.2 Install System Frame

Begin the system installation by bolting the system’s frames to the deck. The frames

should be squared, leveled and plumbed. Ensure the frame hardware is tightly fas-

tened.

Warning! The frame requires at least two persons to place into posi-

tion. Take care not to tip the assembly over.

The system was shipped with cables zip-tied to the frame. Some of the zip ties were

used to secure the cables for shipment purposes.

Note: All trimmed zip ties should remain in place. Any zip ties that

retain the untrimmed long “tail” may be cut when it comes time to connect

the cables.

14 215861 REV E Installation, Outdoor HPO PowerMAX System

2.1.3 Install Waveguide/Combiner Arrays

The waveguide/combiner arrays were shipped intact. Horizontal mounting brackets

(part number L215716) were shipped pre-installed to the frame.

Figure 2-5 shows how to connect the waveguide array to the horizontal wave-

guide supports installed to the frame.

Note: Labels are affixed to the waveguide/combiner arrays (SSPA

1.1 and SSPA 2.1). Make sure to install the waveguide/combiner array to

the proper amplifier module, as labeled. The figure above shows the

waveguide array for SSPA 1.1.

Figure 2-5: Install Waveguide/Combiner Arrays to Frame (System 1 shown)

Installation, Outdoor HPO PowerMAX System 215861 REV E 15

2.1.4 Install High Power Outdoor SSPA Modules

Each of the frame assemblies has slots to install up to four (4) High Power Outdoor

SSPA units. Identification stickers are affixed to the frame adjacent to the space where

the matching SSPA module should be installed. All SSPA units are labeled. When in-

stalling the SSPAs, make sure to match SSPAs from the same system together, and

insert the corresponding SSPA unit to its position in the frame. This will reduce the

need to optimize the system output at initial startup.

Caution! Each SSPA weighs in excess of 100 lbs. (45.5 kg). At least

two persons are required to install each SSPA. Lift the SSPA by the han-

dles on either side. Do not lift from the RF Output waveguide flange or by

the connectors.

Aluminum mounting supports are attached to each High Power Outdoor SSPA unit.

Slide the mounting supports along the frame rails at the opening opposite the wave-

guide array. Position the amplifier so the RF Output flange is inserted into the opening,

with the SSPA supports at the bottom. See Figure 2-6.

Begin with the bottom-most amplifier in each system (SSPA 1.4 or SSPA 2.4). Careful-

ly slide the amplifier along the frame rail until the SSPA mounting support nears the

square washer stop. Adjust the amplifier side-to-side until the RF Output waveguide

flange aligns with the waveguide array. Insert an appropriately sized half gasket

(provided) between the High Power Outdoor SSPA module RF output and the wave-

guide assembly.

Figure 2-6: Install SSPAs into Frame

16 215861 REV E Installation, Outdoor HPO PowerMAX System

Ensure the High Power Outdoor SSPA module is level, and properly aligned with the

waveguide assembly. Slide the module forward, guiding the studs on the waveguide

array through the SSPA waveguide flange, until the mounting supports touch the

square washer stop. Loosely secure the amplifier to the rail using four (4) sets of 1/2”

hex bolts, 1/2” lock washers, 1/2” flat washers and hex nuts, two per side, as shown in

Figure 2-7.

Fasten the waveguide flanges together using the hardware provided. See Figure 2-8.

Repeat for each of the High Power Outdoor SSPA modules in the system, installing

from the bottom, up.

Figure 2-7: Loosely Bolt SSPA to Frame

Figure 2-8: Fasten SSPA Waveguide Flanges

Installation, Outdoor HPO PowerMAX System 215861 REV E 17

Note: It may be necessary to install all amplifiers before securing

the hardware at the waveguide flanges. Any attempts to align the wave-

guide should be made by adjusting the entire waveguide/combiner array

as shown in Figure 2-6, Notes 3 and 4.

A green/yellow striped ground wire was shipped attached to the frame adjacent to each

amplifier. Connect the ground wire ring terminal to the ground stud of each amplifier.

Tighten hardware securely.

2.1.5 Install Output Magic Tee/Termination

The Output Magic Tee assembly includes the Magic Tee and termination, which was

pre-installed at the factory, a dual crossguide coupler and two (2) sections of flexible

waveguide.

Keep this hardware loose until the flexible waveguide is installed (as described in Sec-

tion 2.1.5.2 and Figure 2-10).

2.1.5.1 Connect Dual Crossguide Coupler

Install the dual crossguide coupler to the magic tee. Insert the provided full gasket be-

tween the magic tee and crossguide coupler. Secure the crossguide coupler to the

magic tee using the hardware provided, as shown in Figure 2-9.

Figure 2-9: Install Dual Crossguide Coupler

18 215861 REV E Installation, Outdoor HPO PowerMAX System

2.1.5.2 Connect Flexible Waveguide

The 8-way system Magic Tee is connected to the Magic Tee of each 4-way system

with sections of flexible waveguide.

Insert an appropriately sized half gasket (provided) in the grooved flange of the Magic

Tees to either side of the flex waveguide segments.

Connect the waveguide between the Magic Tees as shown in Figure 2-10. Note that

the 8-way system Magic Tee support takes the place of one of the nut plates when

connecting the flexible waveguide segment.

Figure 2-10: Install Flex Waveguide

Installation, Outdoor HPO PowerMAX System 215861 REV E 19

2.1.6 Install Optional Maintenance Switch

The Outdoor High Power Outdoor PowerMAX system includes an option for a mainte-

nance switch, which can be used to direct the system output to a dummy load for

maintenance purposes. This section details the installation of the components used in

this option.

2.1.6.1 Check Installation Optional Maintenance Switch Termination

If the system includes the optional Maintenance Switch, the associated termination will

have shipped in place from the factory.

Check that the supports for the maintenance switch termination are secured tightly to

the frame. Ensure the maintenance switch termination is fastened to the support brack-

et.

Note that there is a set of stand-off screws (two in front; two in rear) that may be used

to adjust the vertical position and level of the termination.

2.1.6.2 Install Optional Maintenance Switch Waveguide Assembly

Install the maintenance switch waveguide assembly between the RF Output of the

standard system, just after the crossguide coupler, and the termination, as shown in

Figure 2-11.

Figure 2-11: Install Optional Maintenance Switch Waveguide Assembly

20 215861 REV E Installation, Outdoor HPO PowerMAX System

Insert an appropriately sized half gasket (provided) in the grooved flange of the

crossguide coupler. Connect the waveguide flange of the E-bend waveguide to the

flange of the crossguide coupler.

Install the waveguide that connects the maintenance switch to the termination. Insert

an appropriately sized half gasket (provided) in the grooved flanges at either end of the

waveguide installation.

2.1.6.3 Install Optional Maintenance Switch Controller

Install the optional Maintenance Switch Controller into a standard 19” equipment rack

in a sheltered environment. The standard length of the communication cable that con-

nects between the controller and the system is 100 ft. (30m). Keep access to the rear

panels of the controller available to connect the communication cables.

Plug the provided IEC line cords into the power supplies at the rear panel of each con-

troller. Plug in the opposite ends to a power source.

Page is loading ...

Paradise Datacom High Power Outdoor PowerMAX Systems Owner's manual

Paradise Datacom High Power Outdoor PowerMAX Systems Owner's manual

Related papers

Other documents