Selecting wake source
Slide WAKE MODE to or .
• – wake to radio
•
– wake to alarm
• The indicator lights against the
wake source icon on the smaller
display located at the upper right
corner. Refer to Wake time display.
• Once the wake source is selected,
the wake function will be activated
at the set wake time.
Wake time display
• The smaller wake time display is
located at the upper right corner
of the unit.
• The above example shows the
wake time is set at 8:30am with
alarm selected as the wake source.
To cancel the wake function
completely:
• Slide WAKE MODE to OFF. No
indicator lights against the wake
source icon.
• The wake time display shows OFF
to indicate that wake function has
been deactivated.
• The set wake time will not be
erased and can be used the next
time when you switch on wake
function again.
Setting clock manually
1. Slide SET to .
2. Press REV
or FWD to set the
clock time. The time decrements or
increments will follow by a faster
rate when you press and hold the
buttons. AM or PM also shows
beside the time on the display.
3. When nished, slide SET to to
lock the current setting.
not operate normally, or has been
dropped.
• ADDITIONAL SAFETY
INFORMATION
• Apparatus shall not be exposed
to dripping or splashing and no
objects lled with liquids, such
as vases, shall be placed on the
apparatus.
• Always leave su cient space
around the product for ventilation.
Do not place product in or on a
bed, rug, in a bookcase or cabinet
that may prevent air ow through
vent openings.
• Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
• Connect power cord only to AC
power source as marked on the
product.
• Care should be taken so that
objects do not fall into the
product.
• Do not attempt to disassemble
the cabinet. This product does
not contain customer serviceable
components.
• Protect the power cord from being
walked on or pinched particularly
at plugs, convenience receptacles,
and the point where they exit from
the apparatus.
• Only use attachments/accessories
speci ed by the manufacturer.
• Use only with the cart, stand,
tripod, bracket, or table speci ed
by the manufacturer, or sold with
the apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
• Unplug this apparatus during
lightning storms or when unused
for long periods of time.
• Refer all servicing to quali ed
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
user manual
guide de l’utilisateur
EN/F
It is important to read this instruction prior to using your new product for the rst time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre nouveau produit
pour la première fois.
RPC100
v4.0 (EN/F)
FCC information
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of FCC Rules.
These limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications.
However, there is no guarantee
that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment o and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit di erent from
that to which the receiver is
connected.
• Consult the dealer or an
experienced radio/TV technician
for help.
Changes or modi cations not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate the
equipment.
Maufacturer/Responsible Party
Audiovox Electronics Corp.
150 Marcus Blvd., Hauppauge,
NY 11788
For your records
In the event that service should be
required, you may need the model
number and the serial number. In the
space below, record the date and place
of purchase and the serial number:
Model No.:
Date of Purchase:
Place of Purchase:
Serial No.:
Technical information
Product: Clock Radio
Brand: RCA
Model: RPC100
Power Supply: 120V ~ 60Hz
Power Consumption: 5 Watts
Service information
This product should be serviced
only by those specially trained in
appropriate servicing techniques. For
instructions on how to obtain service,
refer to the warranty included in this
user manual.
The descriptions and characteristics in this owner’s manual are for the purpose of general
reference only and not as a guarantee. In order to provide you with the highest quality product,
we may make changes or modi cations without prior notice. The English version serves as the
nal reference on all product and operational details should any discrepancies arise in other
languages.
IMPORTANT SAFETY INSTRUCTIONS
Before you begin
General controls
Clock
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZ-
ARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Sleep function
Audiovox Electronics Corp.
150 Marcus Blvd, Hauppauge, NY 11788
1-877-833-3491
©2008 Audiovox Electronics Corp.
Trademark(s) ® Registered
Marque(s) ® Deposée(s)
Marca(s) ® Registrada(s)
www.rcaaudiovideo.com
Important battery
precautions
• Any battery may present a risk of
re, explosion, or chemical burn
if abused. Do not try to charge a
battery that is not intended to be
recharged, do not incinerate, and
do not puncture.
• Non-rechargeable batteries, such
as alkaline batteries, may leak if left
in your product for a long period
of time. Remove the batteries from
the product if you are not going to
use it for a month or more.
• If your product uses more than
one battery, do not mix types
and make sure they are inserted
correctly. Mixing types or inserting
incorrectly may cause them to leak.
• Discard any leaky or deformed
battery immediately. They may
cause skin burns or other personal
injury.
• Please help to protect the
environment by recycling or
disposing of batteries according to
federal, state, and local regulations.
]
Plugging in for power
AC OUTLET POWER SUPPLY:
120V~60Hz
• The AC power plug is
polarized (one blade
is wider than the
other) and only ts
into AC power outlets
one way.
• If the plug will not go into the
outlet completely, turn the plug
over and try to insert it the other
way.
• If it still does not t, contact a
quali ed electrician to change the
outlet, or use a di erent one.
• Do not attempt to bypass this
safety feature.
• Power is fed to the unit even when
it is not functioning. To cut the
power supply o , the power cable
must be unplugged.
Top and front
Display
• The default sleep time is
90 minutes.
• The radio will be
switched on once SLEEP is
pressed.
• If you set Sleep function with
low volume level before going
to bed, we advise using the
Wake to Alarm mode.
Battery back-up operation
• This clock radio is equipped with a
memory holding system that can
be powered with 2 “AA” batteries
(included).
• The power failure protection circuit
will not operate unless battery is
installed.
• When normal household power
is interrupted, or AC line cord
is unplugged, the batteries will
power the clock radio to keep
track of time and alarm settings
programmed into memory.
• When the battery backup
functions, the digital display will
not light, however, the function of
alarm still occurs during the power
interruption if remaining battery
power is adequate.
• Normal operation will resume after
AC power is restored so you will
not have to reset the time or the
alarm.
To install the batteries:
1. Remove battery compartment
door (located at the bottom of the
radio) by applying thumb pressure
to the tab on battery door and
then lift the door out and o the
cabinet.
2. Insert 2 AA batteries (included).
3. Replace the compartment door.
Note: we recommend that you replace
the batteries every year.
Power failure indicator
When AC power is interrupted
(disconnected) for a short period of
time, both time and alarm settings
will change (unless battery is
installed). After AC power is restored
(reconnected), the Digital Display
will blink to indicate that power was
interrupted and you should readjust
the time and alarm settings.
Back
Left and right
TUNING – selects radio frequency
VOLUME – adjusts sound volume
BAND – selects radio band (FM/AM)
LIGHT – selects On, O or Auto mode
for the night light located at the
bottom of the unit
DISPLAY – adjusts the display
brightness
Switching on or o
Press ON (RADIO/AUX) to turn on the
radio. Press OFF to turn it o .
Switching band
Slide BAND on the left of the unit to
select AM or FM band.
Tuning radio
Rotate TUNING on the right of the unit
to select radio frequency. Current radio
frequency shows on the display.
Antennas
• AM Antenna – A built-in ferrite rod
antenna eliminates the need for an
outside antenna for AM reception.
Rotating the unit slightly may
improve reception of distant AM
stations.
• FM Antenna – The power cord
acts as your FM antenna. The
power cord picks up moderate
to strong stations and eliminates
the need for an external antenna
in most strong signal areas. Be
sure the power cord is stretched
out to its full length. Do not
coil or bunch the cord together.
Changing position of the power
cord may improve reception.
• Built-In AFC – The Built In
Automatic Frequency Control
(AFC) works only on FM. It helps
reducing drift on FM reception and
keeping the radio locked in on the
FM station to which it is tuned.
When tuning in FM stations, you
may notice that the station you
are tuning can be well-tuned on
two or three nearby points on the
dial. Always tune carefully at the
loudest and clearest point.
Wake function
Setting wake time
1. Slide SET to .
2. Press REV or FWD to set the
wake time. The time decrements or
increments will follow by a faster
rate when you press and hold the
buttons.
• Currently set wake time shows
on the smaller display located at
the upper right corner. AM or PM
indicator also lights beside the
wake time. Refer to Wake time
display.
3. When nished, slide SET to
to
lock the current setting.
You can set the radio to play for a set
length of time (up to 90 min) before
turning o automatically.
Press SLEEP repeatedly to select
a duration (90, 60, 30, 15 min or
OFF) before the radio turns o
automatically.
• To check the remaining duration
before the unit turns o , press
SLEEP once.
• To cancel the sleep function, press
SNOOZE/LIGHT or OFF.
Some of the following information
may not apply to your particular
product; however, as with any
electronic product, precautions should
be observed during handling and use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near
water.
• Clean only with dry cloth.
• Do not block any ventilation
openings. Install in accordance
with the manufacturer’s
instructions.
• Do not install near any heat
sources such as radiators, heat
registers, stoves, or other apparatus
(including ampli ers) that produce
heat.
• Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
two blades and a third grounding
prong. The wide blade or the third
prong is provided for your safety. If
the provided plug does not t into
your outlet, consult an electrician
for replacement of the obsolete
outlet.
• IF YOUR PRODUCT OPERATES
ON BATTERIES, adhere to the
following precautions:
A. Any battery may leak electrolyte
if mixed with a di erent battery
type, if inserted incorrectly, or if all
batteries are not replaced at the
same time.
B. Any battery may leak electrolyte
or explode if disposed of in re
or an attempt is made to charge
a battery not intended to be
recharged.
C. Discard leaky batteries
immediately. Leaking batteries can
cause skin burns or other personal
injury. When discarding batteries,
be sure to dispose of them in
the proper manner, according to
your state/provincial and local
regulations.
Radio
Turning o the wake function
To silence the wake function
temporarily for extra sleep time:
• With SmartSnooze™, press
SNOOZE/LIGHT, SLEEP or NAP
to turn o the wake function
temporarily for extra sleep time.
,
or
• The wake function will activate
again when the snooze period (9
minutes) is over.
• The snooze period is xed and
cannot be changed.
To stop the wake function:
Press OFF. The wake function will
activate again on the following day at
the same time.
SEE MARKING ON BOTTOM OF PRODUCT
OFF – turns o the unit; turns o the
wake function and sleep mode
ON (RADIO/AUX) – turns on the radio
or auxiliary input mode
REV
/ FWD – sets clock or wake
time
SET – selects setting wake time
(
), clock time ( ) or lock the current
wake and clock time settings (
)
WAKE MODE – selects wake to radio
(
), wake to alarm ( ) or deactivate
the wake function (OFF)
SLEEP – activates the Sleep function
SNOOZE/LIGHT – turns o the wake
function temporarily; cancels the
sleep function; turns on the night light
brie y with AUTO mode selected (refer
to Night light for more information)
NAP – activates the NAP function
AUX IN – connects external audio
source (e.g. mp3 player) with an audio
cable (not supplied)
TIME ZONE – selects time zone
DAYLIGHT SAVING TIME – switches
the daylight saving time on or o
ENOZ EMIT
Bottom
Before plugging for power
1. Set the Time Zone
Slide the time zone selector at
the bottom of the unit to Eastern,
Central, Mountain or Paci c. (Refer
to the maps on the right)
2. Set the Daylight Saving Time
Slide the day light saving selector
at the bottom of the unit to turn
on/o in areas observing/not
observing such time change. The
icon shows on the display when
daylight saving time is active.
WARNING: Please avoid playing with
these buttons after entering the Clock/
Alarm set mode.
Auto clock set
You do not have to set the clock time
as a built-in automatic time set system
is equipped in this clock powered by
3V (2 X AA batteries, included). All
you have to do is to plug this clock for
power and current time will be shown
automatically.
However, the batteries can also be
exhausted and we recommend that
you replace the batteries every year.
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
Washington
Oregon
Arizona
New Mexico
Te xa s
Oklahoma
Kansas
Colorado
Utah
Nevada
California
Idaho
Montana
North Dakota
Nebraska
Minnesota
Iowa
Missouri
Arkansas
Mississippi
Alabama
Louisiana
Florida
Georgia
Wisconsin
Illinois
Indiana
Ohio
Michigan
New Jersey
New York
Conn.
R.I.
Mass.
N.H.
Maine
Wyoming
Pennsylvania
Virginia
Virginia
West
Delaware
Md.
Vt.
Carolina
North Carolina
South
Olympia
Boise
Helena
Salt Lake City
Pierre
Cheyenne
Lincoln
St. Paul
Des Moines
Madison
Lansing
Harrisburg
Tre n t on
Providence
Hartford
Concord
Albany
Montpelier
Augus ta
Carson City
Phoenix
Santa Fe
Denver
Oklahoma City
Austin
Jefferson City
Little Rock
Jackson
Springfield
Indianapolis
Montgomery
Columbus
Charleston
Columbia
Atlanta
Richmond
Raleigh
Annapolis
Boston
Washington, D.C.
Top e k a
New York
Chicago
Miami
Philadelphia
Detroit
Houston
Dallas
Seattle
Las Vegas
Los Angeles
San Francisco
Sacramento
Memphis
New Orleans
St. Louis
Baton
Rouge
Salem
Bismarck
South Dakota
Te nn e s se e
Kentucky
Nashville
Frankfort
Pacific
Mountain
Central Eastern
Summer
Winter
Winnipeg
Saskatoon
Regina
Yukon
Territory
Alberta
Saskatchewan
Manitoba
Ontario
British
Columbia
Quebec
Newfoundland
Northwest Territories
Nunavut
Pacific
Mountain
Central Eastern
Summer Winter
US time zones
Canadian time zones
General controls
Display brightness
Rotate DISPLAY on the left of the unit
to increase or decrease the display
brightness.
Night light
To select the night light setting:
Night light is located at the bottom
of the unit. Slide LIGHT on the left of
the unit to select one of the following
settings:
• ON – always turns on the night
light;
• AUTO – turns on the automatic
night light mode;
• OFF – always turns o the night
light.
To use the automatic night light
mode:
• Press SNOOZE/LIGHT to turn on
the night light for about 5 seconds.
• The night light also turns on when
the wake function activates.
NAP function
For catnaps up to 2 hours without
disturbing the regular wake function
settings. The NAP function wakes you
up after a set length of time.
1. Press NAP repeatedly to cycle
among the NAP time available (10
min, 20min, 30min, 60min, 90min
and OFF; 20min is the default
setting).
• The NAP icon ashes on the
display while adjusting.
2. When the desired NAP time is
selected, release NAP and wait for
about 5 seconds, the NAP time is
now set.
• The icon NAP lights on the display.
Auxiliary input
1. Connect your auxiliary input source
(e.g. mp3 player) to the AUX IN
jack on the back of the unit with
an audio cable (not supplied).
2. Press ON (RADIO/AUX) twice to
turn on the unit and select the
AUX mode.
• The AUX icon lights on the display.
3. Start playback from the auxiliary
source.
4. Adjust the auxiliary source to
mid-range volume and adjust the
master volume by rotating the
VOLUME knob on the unit.
• Do not turn the volume of the
auxiliary source too high as this
may a ect the sound quality.
• For other playback operations,
control them on your auxiliary
source.
5. When nished listening, press ON
(RADIO/AUX) to switch to the
radio or press OFF to turn o the
unit.
• Press NAP once to show
brie y the NAP time left.
• Only alarm tone can be
used with the NAP function.
• Press OFF to cancel the NAP
alarm, or press and hold NAP
until the NAP icon no longer
shows on the display to cancel
the NAP function.
Warranty information
12 Month Limited Warranty
Applies to RCA Audio/Video Products
• AUDIOVOX ELECTRONICS CORP. (the
Company) warrants to the original retail
purchaser of this product that should
this product or any part thereof, under
normal use and conditions, be proven
defective in material or workmanship
within 12 months from the date of
original purchase, such defect(s) will be
repaired or replaced with reconditioned
product (at the Company’s option)
without charge for parts and repair labor.
• To obtain repair or replacement within
the terms of this Warranty, the product
is to be delivered with proof of warranty
coverage (e.g. dated bill of sale),
speci cation of defect(s), transportation
prepaid, to the Company at the address
shown below.
• This Warranty does not extend to the
elimination of externally generated
static or noise, to correction of antenna
problems, loss/interruptions of broadcast
or internet service, to costs incurred for
installation, removal or reinstallation
of product, to corruptions caused by
computer viruses, spyware or other
malware, to loss of media, les, data
or content, or to damage to tapes,
discs, removable memory devices or
cards, speakers, accessories, computers,
computer peripherals, other media
players, home networks or vehicle
electrical systems.
• This Warranty does not apply to any
product or part thereof which, in the
opinion of the Company, has su ered
or been damaged through alteration,
improper installation, mishandling,
misuse, neglect, accident, or by removal
or defacement of the factory serial
number/bar code label(s). THE EXTENT
OF THE COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
• This Warranty is in lieu of all other
express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED
TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH
OF ANY WARRANTY HEREUNDER
INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY MUST BE BROUGHT
WITHIN A PERIOD OF 24 MONTHS
FROM DATE OF ORIGINAL PURCHASE.
IN NO CASE SHALL THE COMPANY BE
LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH
OF THIS OR ANY OTHER WARRANTY. No
person or representative is authorized
to assume for the Company any
liability other than expressed herein in
connection with the sale of this product.
• Some states do not allow limitations on
how long an implied warranty lasts or
the exclusion or limitation of incidental
or consequential damage so the above
limitations or exclusions may not apply
to you. This Warranty gives you speci c
legal rights and you may also have other
rights which vary from state to state.
How to make a warranty claim:
• If your product is capable of storing
content (such as an mp3 player, digital
voice recorder, etc), it is recommended
to make periodic backup copies of
content stored on the product. If
applicable, before shipping a product,
make a back up copy of content or data
stored on the device. Also, it is advisable
to remove any personal content which
you would not want exposed to others.
IT IS LIKELY THAT CONTENTS AND
DATA ON THE DEVICE WILL BE LOST
DURING SERVICE AND REFORMATTING.
AUDIOVOX ACCEPTS NO LIABILITY FOR
LOST CONTENT OR DATA, OR FOR THE
SECURITY OF ANY PERSONAL CONTENT
OR DATA ON THE RETURNED DEVICE.
Product will be returned with factory
default settings, and without any pre-
loaded content which may have been
installed in the originally purchased
products. Consumer will be responsible
for reloading data and content.
Consumer will be responsible to restore
any personal preference settings.
• Properly pack your unit. Include any
remotes, memory cards, cables, etc.
which were originally provided with the
product. However DO NOT return any
removable batteries, even if batteries
were included with the original purchase.
We recommend using the original carton
and packing materials.
• Include evidence of purchase date such
as the bill of sale. Also print your name
and address and a description of the
defect. Send via standard UPS or its
equivalent to:
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd.
Hauppauge N.Y. 11788
1-877-833-3491
• Insure your shipment for loss or damage.
Audiovox accepts no liability in case of
damage or loss en route to Audiovox.
• Pay any charges billed to you by the
Exchange Center for service not covered
by the warranty.
• A new or refurbished unit will be
shipped to you freight prepaid.
What we will do:
Provide you with a new, or at our option, a
refurbished unit. The exchange unit is under
warranty for the remainder of the original
product’s warranty period.
For Canada Customers, please ship to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
Wake to Alarm uses
GRAD-U-WAKE, a
gentle increase to the
maximum alarm tone volume
over 30 to 45 seconds.
Page is loading ...
Page is loading ...
Page is loading ...
/