Handi Treads NST633748BK1 Installation guide

Brand
Handi Treads
Model
NST633748BK1
Type
Installation guide
Handi‐Treads Wood Installation
Whatyouwillneed:
●YourHandiTread(s)andincludedscrews
●Apowerdrillorascrewdriver
●Atapemeasure
1.AlignyourHandiTreadinthedesiredstairposition.Ifyouareinstallingatread,setitbackroughly½”
fromtheedge.Ifyouareinstallinganosing,makesureitfitssnuglyattheedgeofyourstair.

2.Startingwiththemiddlescrewholes,drillyourscrewsintothestairworkingyourwayoutfromthecenter.
Makesurethatyouaredrillingperpendiculartothesurfaceandthatyouuseallofthescrewholesprovided.
Installationiscompleteonceallscrewshavebeendrilledintoplace.Notethatthescrewholesarenot
raised;DONOTusetheraisedtractionbumpsforyourscrewplacement.

Handi‐Treads Concrete Installation
Whatyouwillneed:
●YourHandiTread
●Clearliquidsilicone(OPTIONAL)
●3/16”drivepinanchors
●3/16”masonrydrillbit
●Ahammer
●Apowerorhammerdrill
Werecommendusingahammerdrillbutapowerdrillwilldothejob.TypesofFastenersHandiTreadsrecommendsusingdrive
pinstofastenyourtreadstoyourstairs.Ensurethateachdrivepinisatleast¾”long.
HandiTreadConcreteStairInstallation
1.Onceyouhaveacquiredallofthenecessarymaterials,alignthetreadinthedesiredposition.Ifyouareinstallinganosing,make
surethatitfitssnuglyattheedgeofthestair.Ifyouareinstallingatread,setitbackroughly½”fromtheedge.Usingamarkerand
thetreadasatemplate,placeadotineachofthepinholestomarktheplacementofthedrivepinsontheconcretesurface.Note
thatthepinholesarenotraised,DONOTusetheraisedtractionbumpsforyourpinplacement.
2.Removethetreadfromthestair.Usinga3/16”masonrydrillbitandyourhammer/powerdrillateachmarkedspot,drillaholeinto
theconcretedeepenoughtoaccommodatethelengthoftheconcretedrivepinyouareusing.Makesurethatyouaredrilling
perpendiculartothesurface.Usecautionwhendrillingtheholes.Iftheconcreteisnotingoodconditionoryouaredrillingtooclose
totheedge,theconcretecanfracture.Thiswouldpreventyoufromusingthislocationandwillnecessitatetheneedtorelocatethe
tread.Toensurethatyouaredrillingdeepenough,attachapieceoftapetothedrillbitattheheightofyourscrew.Forexample,if
youareusingapinthatis¾”long,attachthetape¾”abovethetipofthebit.
Inthepicturebelow,thetapehasreachedthesurface,indicatingthattheholeisattheperfectdepth.

3.Makesurethattheholesyouhavedrilledarefreeofanyconcretedebris.
OPTIONAL:Depositasmallamountofclearsiliconeintoeachdrilledhole.
Asthepinsareplacedintheirpositions,theexcesssiliconewillflowoutoftheholeleavingyouwithawatertightseal.Thismeasure
istakentopreventanywaterfromcollectingwithinthepinhole,whichmightcausetheconcretetofractureifitfreezesandexpands.
4.Placethetreadbackinposition,makingsurethateachpinholeisaboveeachdrilledhole,thenplaceadrivepinineachofthe
pinholes.Startinginthecenterofthetread,workyourwaytotheoutside,hammeringeachpinintoitsrespectivehole.Installationis
completewhenallofthedrivepinshavebeenhavebeenhammeredintoposition.
  • Page 1 1
  • Page 2 2

Handi Treads NST633748BK1 Installation guide

Brand
Handi Treads
Model
NST633748BK1
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents