14
Tuning --- Shipping Condition
Shipping condition allows you to reset the TV to its original condition, i.e. no channels tuned in. This is
useful, for example, if you move to a different area when you will probably want the TV to tune itself to
your new local stations.
ThiscanbedoneeitherthroughtheShipping Condition menu or through the Auto setup menu.
The Shipping Condition menu will reset all data, clearing all tuning information and resetting all
control levels back to factory settings.
You may need to adjust your VCR or programme position 0 VCR after operating the Shipping
Condition menu -- refer to page 18.
Press the F button.
Select Setup menu.
Select Tuning menu.
Select Shipping Condition.
Access Setup menu.
Access Tuning menu.
Access Shipping Condition.
Switch TV off and wait for a few
seconds.
Switch TV on again.
Auto setup will begin, stations will
be located, sorted and stored
ready for use. See page 12.
Press TV/AV button to start
1
CH44
Shipping Condition
Tuning data will be erased!
Setup Menu
Auto
Normal
Access
Colour Balance
Tuning Menu
Aspect
Manual Tuning
Swap
Owner ID
Auto Setup
Tuning Menu
Off
Access
Child Lock
Shipping Condition
Select
Access
Exit
Return
Select
Access
Return
Exit
Store
Return
Exit
Start
15
Tuning --- Owner ID
Owner ID allows you to enter a security code and address information so that in the unfortunate event
of theft it will help the Police to determine the owner.
If the Owner ID information was not entered after Auto setup or it is necessary to alter some of the ID
information it can be re-- accessed via the Tuning menu.
Press the F button.
Select Setup menu.
Select Tuning menu.
Select Owner ID.
Access Setup menu.
Access Tuning menu.
Access Owner ID.
If the Owner ID has previously been
set, enter the PIN NUMBER (using 0
to 9 on the remote control) followed by
TV/AV to proceed, this will take you to
the NAME option
If no Owner ID has previously been
set, enter the required 4 digit Owner ID
PIN NUMBER (using 0 to 9 on the
remote control).
If a 4 digit PIN NUMBER was entered
above, you will be taken automatically
to the NAME line.
If not, move to the NAME line.
Change character.
Select character position.
Repeat above until NAME, HOUSE
NUMBER and POSTCODE are
entered.
Press again, to confirm when asked
A re y o u su re ?
The Tuning menu will be displayed.
Press the N button to exit
Press TV/AV to store the details.
1
CH44
For future reference,
write your PIN Number here :
Owner ID
PINNUMBER : 1234
NAME: KKKKKKKKKKKKKK
HOUSE NO : KKKKKKKKKKK
POSTCODE : KKKKKKKKKKK
ABCDEFGHIJKLMNOPQRST
UVWXYZ+-- . 0123456789
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book
Setup Menu
Auto
Normal
Access
Colour Balance
Tuning Menu
Aspect
Manual Tuning
Swap
Auto Setup
Tuning Menu
Off
Access
Child Lock
Shipping Condition
Owner ID
Select
Access
Exit
Return
Select
Access
Return
Exit
Store
Select character
Change character
Return
Exit
Store owner ID
16
Swap --- Programme swapping
The Swap option allows you to swap two programme positions.
Swap
with
Programme 01 CH44 BBC1
Programme 02 CH41 ITV
Press the F button.
Select Setup menu.
Select Tuning menu.
Select Swap.
Access Setup menu.
Access Tuning menu.
Select first programme position.
Confirm by pressing the TV/AV button.
Select second programme position.
Access Swap.
Press the N button to exit.
Select
Adjust
Return
Exit
Swap
Move down to Programme 02 row.
AV selection --- AV mode
` To select AV mode press the TV/AV button. If another receiver is connected to the AV connectors (VCR, Satellite
Receiver, camera, etc. see page 20) and if it is in operation, its signal will be displayed and AV will appear in the top
left corner of the TV screen regardless of the selected programme position (TV tuner is ignored).
` This TV may automatically switch over to the AV mode if the connected device sends a switch signal to the SCART
cable connector. In this case a signal from the connected audio/video device will be displayed and EC or
EC/RGB (when an RGB signal is input) will appear in the upper left corner of the screen. The output displayed will
not change if you change the TV channel.
` You may switch back to the television by pressing the TV/AV button or by disconnecting the AV device.
` Do not connect two AV devices to the TV simultaneously, as their signals will overlap.
` In the AV mode the Setup Menu OSD is extended to include Volume Correction.
` If an NTSC signal is connected via the AV input the TV will automatically detect the signal and switch over to the
NTSC standard. The Main Menu OSD is extended to include Tint, which may be adjusted with buttons + and
--.
17
VCR Controls
The Remote Control is capable of operating some functions of selected Panasonic VCRs. Other VCR
equipment may have different functions, so to ensure compatibility please refer to the equipments
instruction book or consult your dealer for details.
Press to switch the VCR to standby mode. Press
again to switch back on.
VCR Standby
Press to playback the tape.
Play
Press to stop the tape.
Stop
Press to fast forward the tape. In Play mode, press
to view the picture rapidly forward (Cue).
Fast Forward/Cue
Press to rewind the tape. In Play mode, press to
view the picture rapidly in reverse (Review).
Rewind/Review
Press in playback mode, the picture will pause.
Press again to restart play.
Pause/Still
Press to increase or decrease the VCR programme
position by one.
Programme Number Up And Down
Press this button to start recording.
Record
REC
VCR
18
VCR and Satellite Receiver installation
Your new TV is supplied with programme position 0 set to receive an RF signal from your VCR, although a Scart connection is
preferable if the VCR is so equipped.
However, if for some reason your VCR is tuned to a different RF channel then you will not receive any picture or sound from your VCR on
programme position 0 of the TV. It will be necessary to either adjust the RF channel of your VCR (some VCRs allow adjustment of their
RF channel via their remote control unit) or to adjust the tuning of the TVs programme position 0 or both until it receives the RF output
channel of your VCR.
It is intended that this advice is used in conjunction with the instruction books for your ancillary equipment.
Use the AV Scart terminal for a VCR.
To tune your TV to the VCR
Switch on the VCR, insert and play a
pre-- recorded tape with known content.
Press the F button.
Select Setup menu
Access Setup menu
Select Tuning menu.
Access Tuning menu.
Select Manual tuning
Access Manual tuning
Select programme position 0 VCR.
Start searching for the VCR playback
of the known content tape.
When the VCR playback is found, press
TV/AV to store.
Press the N button to exit.
See below for installation of
VCR and
Satellite Receiver.
Notes :
` If picture patterning occurs on programme position 0 it
may be necessary to adjust the RF output channel of the
VCR, refer to the VCR instruction book.
If a Satellite Receiver and a VCR are going to be used with
RF cable connections it is important to avoid both units
being set on the same channel.
Refer to the Satellite Receiver and VCR instruction books
for precise tuning information.
VCR
CH32
VCR
Setup Menu
4:3
Normal
Access
Colour Balance
Tuning Menu
Aspect
21
68
Manual Tuning
Select
Access
Exit
Return
Programme
Search
Return
Exit
Store
19
Teletext function
D Teletext features may vary depending on the Broadcasting Companies and are only available if the selected channel is
transmitting Teletext.
D If the F button is pressed in Teletext mode the cyan contrast scale will appear; press buttons+ and --to change the
settings.
D When in Teletext mode, the volume may still be adjusted by pressing buttons + or --.
What is FLOF (FASTEXT)?
In FASTEXT mode four differently coloured subjects are shown at the bottom of the screen. To access more information
about one of these subjects, push the appropriately coloured button. This function allows fast access to information on
the subjects shown.
Press the TV/TEXT button. The screen will display the Teletext page. Press again when you wish to
return to TV mode.
TV/Teletext Mode
Pages can be selected in two ways:
a) press the Up/Down buttons to increase or decrease the page number by one;
b) enter the page number using 0 --- 9 on the remote control.
Page Selection
In FASTEXT mode, these correspond to the differently coloured subjects.
In LIST mode the buttons correspond to the differently coloured page numbers.
Red/Green/Yellow/Blue Buttons
TV/TEXT
Index
INDEX
REVEAL
F/T/B
Hold
HOLD
Reveal
Press to reveal hidden words, e.g. crossword or quiz page answers, can also display VPS/PDC codes.
Full/Top/Bottom
Teletext information viewing on the screen.
Press to hold the current page. Press again to cancel the hold.
Press this button to return to the main index page. Depending on the way information is transmitted
you may have to press a few times to return to the main index page.
Presstoexpandthetophalfofthepage.
Press again to expand the bottom half.
Press again to return to normal (full) size.
Normalisation
Press the N button to return to TV mode.
When Teletext information exceeds more than one page, it may take some time for the automatic
changing of the sub pages to reach the sub page you require.
Press the TIME TEXT button; **** will be displayed at the top left of the screen. Enter the desired
sub---page number. To select sub---page 5, enter 0, 0, 0 and 5. The TV is now searching for the
correct sub page.
You can continue watching the TV programme by pressing the TV/TEXT button. If you switch back
to Teletext and if the entered page is already available, the sub page will be displayed until a new
page or programme position is entered.
To clear the sub page perform one of the following:
` Press the INDEX button.
` Select a new page number.
` Change the programme position.
Sub Coded Page Access
TIME TEXT
TV/TEXT
20
EXTERNAL AUDIO/VIDEO CONNECTIONS
Rear input/output of AV SCART connector
CAMCORDER
Rear AV SCART 21---pin Terminal and front RCA Socket
Notes
Additional equipment and cables shown above are not supplied with this TV set.
Do not connect computers with TTL (5V) output to this TV set.
When the headphones are connected, the speakers will be automatically disconnected.
Do not connect signals to both front and rear AV terminals simultaneously as this will
cause the audio signals and the video signals from both sources to mix together.
VCR
CAMCORDER
SATELLITE RECEIVER
Audio/video (AV) inputs are designed to connect a VCR, a Satellite Receiver and other
compatible audio/video equipment.
VCR
Headphones
socket
Headphones with
3.5mm (male) jack
L--Raudio
input socket
V --- v i d e o
input socket
2x RCA
audio cables
RCA video
cable
Front AV panel
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
Socket Earth
CVBS out (video)
CVBS earth
Red in
Red earth
Green in
Green earth
Blue in
Blue earth
Audio out (L)
Ausio out (R)
CVBS in (video)
RGB status earth
Status RGB
Earth
--- --- --- ---
--- --- --- ---
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
SCART socket -- AV
H SCART socket information
AV inputs including RGB (red/green/blue)
GAMES CONSOLE / COMPUTER (RGB)
SCART cable
AV cover
21
TROUBLESHOOTING
Symptoms
C
h
e
c
k
Picture Sound
C
h
e
c
k
Snowy picture
Noisy sound
Aerial location, direction or connection
Multiple images
Normal sound
Aerial location, direction or connection
Interference
Noisy sound
Electrical appliances
Cars/motorcycles
Fluorescent lights
Normal picture
No sound
Volume level
Check whether the Mute function has been activated
on Remote Control.
No picture
No sound
TV set to AV mode
Not plugged into A.C. outlet
Not switched on
Picture / Sound controls set at minimum levels
Check if in standby mode
No colour
Normal sound
Colour controls set at minimum levels
Poor or Distorted Picture
Weak or no sound
Retune channel(s)
Coloured patches
Normal sound
Magnetic interference from unshielded equipment
Receiver moved while switched ON, switch TV off for
30 minutes.
Normal picture
Weak or distorted sound
Receiving conditions are bad (e.g. atmospheric
conditions)
22
USER INFORMATION
H Service
Before requesting service, please refer to the trouble---shooting
guide on previous page to determine the symptoms. To obtain
service please contact your local Panasonic dealer quoting the
model number and serial number (both are located at the rear of
the TV).
H TV games/Home computers
Frequent use of the games console or computer may cause
shadows on the screen. This can be avoided if you meet the
following requirements:
` Reduce brightness and contrast to a minimum. viewing
level;
` Do not operate the TV set for a continuous period of time
whileusingTVgamesorhomecomputers.
` This type of picture tube damage, is not an operating
defect, and such as is not covered by the Panasonic
warranty.
H Last position memory
Certain functions have a last position memory, i. e. the setting at
the time of switch ---off will be the setting used when the receiver is
switched on again: ---
Programme positions Tint
Last programme position Contrast
Volume correction (+AV) Sharpness
Volume Brightness
Standby mode Colour
H Sleep feature
If the set is not switched off when the TV station stops transmitting,
it will automatically go to standby mode after 30 minutes. This
function will not operate when the TV is in AV mode.
SPECIFICATIONS
Model TX-14B4T TX-14B4T/B
Power source 220 - 240 V 50Hz A.C.
Power consumption 39W
Standby consumption
2.9W
Picture tube
Visible Diagonal
34 cm
Quintrix
Audio output (Music Power) 2.5W, impedance 8!
Dimensions
H
W
D
342 mm
366 mm
376 mm
Weight (kg) 9.6 kg
R
e
c
e
i
v
i
n
g
S
y
s
t
e
m
s
/
B
a
n
d
n
a
m
e
PAL I UHF E21-- 68
PAL 525/60 Pla
y
back o
f
NTSC ta
p
e from some PAL Video recorders
(
VCR
)
R
ece
i
v
i
ng
S
ystems
/
B
an
d
name
P
A
L
5
2
5
/
6
0
P
l
a
y
b
a
c
k
o
f
N
T
S
C
t
a
p
e
f
r
o
m
s
o
m
e
P
A
L
V
i
d
e
o
r
e
c
o
r
d
e
r
s
(
V
C
R
)
M.NTSC Playback from M.NTSC Videorecorders (VCR)
NTSC (AV input only) Playback from NTSC Videorecorders (VCR)
Number of programme positions 99 + VCR
Aerial --- Rear UHF
Headphones --- Front 3.5 mm, impedance 8!
A V --- R e a r AV --- 21---pin terminal --- Audio/Video in/out, RGB in
A V --- F r o n t Front AV --- RCA Audio/Video in
Specifications are subject to change without notice. Weight and dimensions are approximate.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic TX28CK1 Operating instructions
-
-
Panasonic KX-TG1613BL User manual
-
Panasonic TX28CK1L Operating instructions
-
-
-
-
-
-
