KitchenAid KEBHS 80010 Setup and user guide

Brand: KitchenAid

Model: KEBHS 80010

Category: Cooker hoods

Type: Setup and user guide

This manual is also suitable for

KEBHS 60010

The KitchenAid KEBHS 80010 is a versatile cooking hood that offers both ducting and filtering options, allowing you to customize it to your kitchen's needs. With its automatic operation feature, it can adjust the fan speed based on cooking conditions, ensuring optimal extraction of fumes and odors. The grease filters are dishwasher safe for easy cleaning, and the charcoal filter effectively absorbs unpleasant odors. Additionally, the LED lighting provides bright illumination for your cooking surface.

Thanks for choosing

Cooking gestures are

invisible ingredients.

They turn inspiration

into emotions and

emotions into a

masterpiece.

It’s all about artisanality,

that’s why we take it so

seriously.

Quick Reference Guide

Index

EN pag. 3

Hood

Quick reference guide

Cooking gestures are

invisible ingredients.

They turn inspiration

into emotions and

emotions into a

masterpiece.

It’s all about artisanality

that’s why we take it so

seriously.

Thanks for choosing

Quick Guide

THANK YOU FOR BUYING A

KITCHENAID PRODUCT

In order to receive a more complete assistance, please

Before using the appliance

carefully read the Safety

Instruction.

First time use

Air Vent (for the suction versions)

Connect the hood and discharge holes on the walls with a diameter equivalent to the air outlet

(connection ange).

Using the tubes and discharge holes on walls with smaller dimensions will cause a diminution of the

suction performance and a drastic increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensible length.

! Use a duct with as few elbows as possible (maximum elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! The company declines any responsibility whenever these regulations are not respected.

Filtering or ducting?

! Your cooker hood is ready to be used in suction version.

To use the hood in ltering version the special ACCESSORY KIT must be installed.

Check if the ACCESSORY KIT is furnished or must be bought separately.

Note: If furnished, in certain cases, the additional activated carbon ltering system may be installed

on the hood. Information about the conversion of the hood from suction version to ltering version is

present in the Manual “Safety Instructions & Installation”.

Ducting version

In this case the fumes are conveyed outside of the building by means of a special pipe connected with

the connection ring located on top of the hood.

Attention! The exhausting pipe is not supplied and must be purchased apart. Diameter of the

exhausting pipe must be equal to that of the connection ring.

Attention! If the hood is supplied with active charcoal lter, then it must be removed.

Filter version

The aspirated air will be degreased and deodorised before being fed back into the room.

In order to use the hood in this version, you have to install a system of additional ltering based on

activated charcoal.

Product Description

Control panel

L2-L3

T1. ON/OFF button “Automatic operation (sensor)” - see the function list in the next paragraph.

T2. Suction speed (power) control button: 1, 2, 3, intensive.

Note: Intensive speed lasts for about 5 minutes, then it is automatically set to speed 2.

T3. ON/OFF button (short press) and light intensity setting (long press).

CAUTION! This hood has an automatic operation system (see paragraph “Automatic operation

(sensor)”).

Calibration occurs automatically each time the hood is reconnected to the electrical network (e.g.: the

rst time it is installed after a blackout). It can also be performed manually (see paragraph “Setting of

parameters for Automatic Operation - Manual setting”).

During calibration, which lasts for 5 minutes, the controls will ash and only the lights button can be

used.

Filter Saturation Indicator

The hood signals when necessary to perform lter maintenance:

Grease lter (every 40 hours of use): all Leds with red light.

Activated charcoal odour lter (every 160 hours of operation): all LEDs with red light, LEDs L2 and L3

blink.

Reset Filter Saturation

After performing lter maintenance, press and hold buttons T1 and T3, Leds L1, L2 and L3 blink briey

in red and then turn off for good.

• Activation indicator for odour lter saturation with activated charcoal: This indicator is normally

disabled. To enable it, proceed as follows:

With the hood off, press and hold simultaneously T1 and T2: L1 turns on rst, then L2 and L3 and

after that, when the buttons are released, the Leds L2 and L3 ash briey to indicate successful

activation.

• Disabling the LED for charcoal lter saturation: repeat the operation above; rst the LEDs L1, L2

and L3 turn on simultaneously, then only L1, and after that, when the buttons are released, the leds

L1, L2 and L3 turn on again to indicate successful disabling.

Automatic operation (sensor)

CAUTION! We recommend running the “Automatic operation settings” procedure (see below) before

running the unit in automatic mode.

Automatic operation (sensor)

The hood will turn on at the speed most suited to the cooking conditions detected by its sensor.

To activate this function:

Press button T1 briey, LED L1 will turn on white.

Parameter setting for automatic operation

Parameter setting duly takes place automatically whenever the hood is connected to the mains (for

example: with the rst installation or after a power cut) or manually.

Note: All the manual operations of calibration, selection, setting and logical connection described

below are possible with the hood OFF and automatic operation OFF (T1 OFF- L1 OFF).

Manual setting

To be performed when you notice that automatic operation is functioning unsatisfactorily; it must be

performed when there are normal environmental conditions in the kitchen.

Manual setting includes:

• Calibration of the hood:

• Selecting the type of hob (gas - induction or electric).

Calibration of the hood:

Hold down the button T1 (approximately 10 seconds), the LED L1 ashes to indicate that calibration

has begun, the calibration process will last about 5 minutes.

Selecting the type of hob (gas - induction or electric)

Hold down the button T2 (about 10 sec), all the LEDs start ashing for 5 sec.

Within this period press T1 to select the hob that you own:

Orange LED: gas hob.

Blue LED: induction hob.

White LED: electric hob

Wait 5 sec. to allow the hood to record the selection made and until all LEDs go out.

Technical data

Cleaning and maintenance

Cleaning

• Do not use steam-cleaning equipment.

• Disconnect the appliance from the mains.

Important: do not use corrosive or abrasive detergents. If any such products unintentionally come into

contact with the appliance, clean the appliance immediately with a damp cloth. Do not use alcohol.

• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing-up detergent to

the water. Finish off with a dry cloth.

Important: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin the

enamel surfaces.

Use detergents specically designed for cleaning the appliance and follow the manufacturer’s

instructions.

Important: clean the lters at least once a month to remove oil and grease residue.

Maintenance of the panel

Disassembly:

a. pull the panel (FRONT SIDE) downwards energetically;

b. unhook it from the back hinges.

Cleaning:

the suction panel must be cleaned as frequently as the grease lter, use a dampened cloth with

neutral liquid detergents.

Avoid using products containing abrasives. DO NOT USE ALCOHOL!

Assembly:

The panel must be hooked in the back and xed in the front (with magnets).

Height (cm) Width (cm) Depht (cm) Ø of exaust tube (cm)

36.7 52.3-72.3 29 15

Attention! always check that the panel is tightly xed to its place.

Maintenance of the grease lters

This must be cleaned once a month using non aggressive detergents, either by hand or in the

dishwasher, which must be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease lter may discolour slightly, but this does not affect its

ltering capacity.

Pull out the handle to remove the lter.

Once the lter has been washed and left to dry, proceed in reverse order to ret the lter.

Maintenance of the charcoal lter (for ltration models only)

This lter retains the unpleasant odours produced during cooking.

Saturation of the carbon lter occurs after a relatively long use, however this depends on the type

of cooking and how regularly the grease lter is cleaned. Regardless, it is necessary to replace the

cartridge every 4 months. It CANNOT be washed or recycled.

Fitting or replacing the carbon lter

1. Disconnect the hood from the mains.

2. Remove the grease lters.

3. Fit 2 carchoal lters (one each side of the conveyour), attachment.

4. Reinstall the grease lter in place.

Proceed in reverse order to remove.

Replacing the lamps

Note: For replacement LED, please contact the Technical After-sales Service Centre.

Troubleshooting

Problem Solutions

The appliance does not work. • Check the mains voltage and whether the appliance is

connected to the power supply;

• Check that a speed has been selected;

• Switch the appliance off and on again to see if the fault

persists.

The hood is not extracting air

sufciently.

• Check that the air extraction speed is set to the desired

level;

• Check that the lters are clean;

• Check the air vents for any obstructions.

The hood has turned off during

normal functioning.

• Check that the power has not been disconnected;

• Check that the omnipolar disconnection device has not

tripped.

Please refer to our website www.kitchenaid.eu for complete instructions for use.

In addition, you will nd a lot more useful information about your products, such as inspiring

recipes created and tested by our brand ambassadors or the nearest KitchenAid cookery school.

400011328297

Printed in Italy

KitchenAid KEBHS 80010 Setup and user guide

Brand: KitchenAid

Model: KEBHS 80010

Category: Cooker hoods

Type: Setup and user guide

This manual is also suitable for

KEBHS 60010

Download PDF

report

KitchenAid KEBHS 80010 Setup and user guide

This manual is also suitable for

KitchenAid KEBHS 80010 Setup and user guide

Related papers

Other documents