Anybus AB7311 User manual

+$/067$'&+,&$*2.$5/658+(72.<2%(,-,1*0,/$1208/+286(&29(175<381(&23(1+$*(1

HMS Industrial Networks

Mailing address: Box 4126, 300 04 Halmstad, Sweden

Visiting address: Stationsgatan 37, Halmstad, Sweden

Connecting Devices

TM

E-mail: [email protected]

Web: www.anybus.com

User Manual

Anybus® Communicator CAN

EtherCAT

Doc.Id. HMSI-168-58

Rev. 1.11

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Important User Information

This document is intended to provide a good understanding of the functionality offered by the Anybus Communi-

cator CAN - EtherCAT.

The reader of this document is expected to be familiar with high level software design, and communication

systems in general. The use of advanced EtherCAT specific functionality may require in-depth knowledge of

EtherCAT networking internals and/or information from the official EtherCAT specifications. In such cases, the

people responsible for the implementation of this product should either obtain the EtherCAT specification to gain

sufficient knowledge or limit their implementation in such a way that this is not necessary.

Liability

Every care has been taken in the preparation of this manual. Please inform HMS Industrial Networks AB of any

inaccuracies or omissions. The data and illustrations found in this document are not binding. We, HMS Industrial

Networks AB, reserve the right to modify our products in line with our policy of continuous product development.

The information in this document is subject to change without notice and should not be considered as a commit-

ment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no responsibility for any errors that

may appear in this document.

There are many applications of this product. Those responsible for the use of this device must ensure that all the

necessary steps have been taken to verify that the applications meet all performance and safety requirements in-

cluding any applicable laws, regulations, codes, and standards.

HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems that

may arise as a result from the use of undocumented features, timing, or functional side effects found outside the

documented scope of this product. The effects caused by any direct or indirect use of such aspects of the product

are undefined, and may include e.g. compatibility issues and stability issues.

The examples and illustrations in this document are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular implementation, HMS Industrial Networks AB cannot

assume responsibility for actual use based on these examples and illustrations.

Intellectual Property Rights

HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product de-

scribed in this document. These intellectual property rights may include patents and pending patent applications

in the US and other countries.

The “Silk” icon set, used in the Anybus Configuration Manager tool, is created by Mark James, Birmingham, Eng-

land. The complete icon set is found at http://famfamfam.com/lab/icons/silk/. The icon set is licensed under the

Creative Commons Attribution 2.5 License (http://creativecommons.org/licenses/by/2.5).

Trademark Acknowledgements

Anybus ® is a registered trademark of HMS Industrial Networks AB. All other trademarks are the property of their

respective holders.

EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff Automation GMbH,

Germany.

Warning: This is a class A product. in a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

ESD Note: This product contains ESD (Electrostatic Discharge) sensitive parts that may be damaged if ESD

control procedures are not followed. Static control precautions are required when handling the prod-

uct. Failure to observe this may cause damage to the product.

Anybus Communicator CAN - EtherCAT User Manual

Rev 1.11

Nov 2012 Doc Id HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Doc.Id. HMSI-168-58

Preface About This Document

Related Documents.................................................................................................................................. 1

Document History ................................................................................................................................... 1

Conventions & Terminology.................................................................................................................. 2

Sales and Support ..................................................................................................................................... 3

Chapter 1 About the Anybus Communicator CAN

Introduction .............................................................................................................................................. 4

Anybus Communicator CAN Concept.................................................................................................5

General............................................................................................................................................ 5

Data Exchange Model..................................................................................................................... 6

Chapter 2 About the Module

External view............................................................................................................................................. 7

Mounting.................................................................................................................................................... 8

Status LEDs .............................................................................................................................................. 9

Connectors .............................................................................................................................................. 10

Ethernet Connectors ....................................................................................................................... 10

USB Connector.............................................................................................................................. 10

CAN Connector............................................................................................................................ 10

Power Connector.................................................................................................................................... 11

Software Installation .............................................................................................................................. 12

Anybus Configuration Manager ..................................................................................................... 12

Firmware Update........................................................................................................................... 12

Table of Contents

II

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Chapter 3 Getting Started

Chapter 4 CAN Network Communication

General..................................................................................................................................................... 14

Types of Messages.................................................................................................................................. 14

Query-Response.............................................................................................................................. 14

Produce and Consume .................................................................................................................... 15

Protocol Building Blocks....................................................................................................................... 15

Control/Status Word............................................................................................................................. 17

Transaction Live List ............................................................................................................................. 18

Chapter 5 EtherCAT Communication

General..................................................................................................................................................... 19

Sync Managers...............................................................................................................................19

FMMUs ....................................................................................................................................... 19

Addressing Modes.......................................................................................................................... 19

Implemented Services ...................................................................................................................... 20

CANopen Implementation Details...................................................................................................... 20

General Information....................................................................................................................... 20

Implemented Services ...................................................................................................................... 20

Data Representation............................................................................................................................... 21

Memory Layout (Internal Memory Buffer)...................................................................................... 22

Chapter 6 Configuration

Configuring the Anybus Communicator CAN.................................................................................. 23

Configuring the EtherCAT Network .................................................................................................. 23

Chapter 7 Anybus Configuration Manager

Main Window.......................................................................................................................................... 24

Pull-down Menus ........................................................................................................................... 25

III

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Chapter 8 Basic Settings

Project ...................................................................................................................................................... 28

Network Settings .................................................................................................................................... 28

Communicator Settings ......................................................................................................................... 29

Subnetwork Settings............................................................................................................................... 30

Chapter 9 Groups and Transactions

General..................................................................................................................................................... 31

Groups ..................................................................................................................................................... 31

Transactions ............................................................................................................................................ 31

Produce .......................................................................................................................................... 32

Consume ........................................................................................................................................ 33

Query/Response............................................................................................................................. 34

Dynamic Produce ........................................................................................................................... 35

Dynamic Consume ......................................................................................................................... 36

IV

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Chapter 10 Configuration of CAN Frames

General..................................................................................................................................................... 37

CAN Identifiers ............................................................................................................................ 37

Produce/Query CAN Frame................................................................................................................ 38

Consume/Response CAN Frame........................................................................................................ 38

CAN Frames in Dynamic Transactions..............................................................................................39

Chapter 11 Online

Select Connection................................................................................................................................... 40

Connect/Disconnect ............................................................................................................................. 41

Download and Upload Configuration................................................................................................. 41

Chapter 12 Anybus Configuration Manager Tools

Monitor/Modify ..................................................................................................................................... 42

CAN Line Listener................................................................................................................................. 43

Address Overview .................................................................................................................................. 44

Diagnostics/Status ................................................................................................................................. 45

Reassign Addresses ................................................................................................................................ 46

Project Summary .................................................................................................................................... 47

Password .................................................................................................................................................. 48

Options .................................................................................................................................................... 49

Appendix A Technical Specification

Protective Earth (PE) Requirements................................................................................................... 50

Power Supply .......................................................................................................................................... 50

Environmental Specification ................................................................................................................ 50

Temperature................................................................................................................................... 50

Relative Humidity.......................................................................................................................... 50

EMC (CE) Compliance ......................................................................................................................... 51

Appendix B Configuration Example

Appendix C Object Dictionary Implementation

Standard Objects .................................................................................................................................... 56

General.......................................................................................................................................... 56

Object Entries................................................................................................................................56

Manufacturer Specific Objects ............................................................................................................. 57

General.......................................................................................................................................... 57

Input Buffer ................................................................................................................................... 57

Output Buffer................................................................................................................................. 58

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Preface

P. About This Document

For more information, documentation etc., please visit the HMS website, ‘www.anybus.com’.

P.1 Related Documents

P.2 Document History

Summary of Recent Changes (1.10 ... 1.11)

Revision List

Document Author

CAN protocol specification www.can-cia.org

EtherCAT Communication Specification EtherCAT Technology Group

EtherCAT Indicator Specification EtherCAT Technology Group

Change Page(s)

Information about EtherCAT trademark added

Revision Date Author(s) Chapter(s) Description

1.00 2011-09-22 KeL - First official release

1.01 2012-02-13 KeL 12 Minor updates

1.10 2012-09-10 KaD, KeL 2, 4, 7, 8, 9,

10, 11, 12

Service pack 1 updates

1.11 2012-11-20 KeL I Information about EtherCAT trademark added

About This Document 2

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

P.3 Conventions & Terminology

The following conventions are used throughout this manual:

• Numbered lists provide sequential steps

• Bulleted lists provide information, not procedural steps

• The terms ‘Anybus’ or ‘module’ refers to the Anybus Communicator CAN module.

• The terms ‘host’ or ‘host application’ refers to the device that hosts the Anybus module.

• Hexadecimal values are written in the format NNNNh or 0xNNNN, where NNNN is the hexa-

decimal value.

• A byte always consists of 8 bits.

About This Document 3

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

P.4 Sales and Support

Sales Support

HMS Sweden (Head Office)

E-mail: [email protected] E-mail: [email protected]

Phone: +46 (0) 35 - 17 29 56 Phone: +46 (0) 35 - 17 29 20

Fax: +46 (0) 35 - 17 29 09 Fax: +46 (0) 35 - 17 29 09

Online: www.anybus.com Online: www.anybus.com

HMS North America

E-mail: [email protected] E-mail: [email protected]

Phone: +1-312 - 829 - 0601 Phone: +1-312-829-0601

Toll Free: +1-888-8-Anybus Toll Free: +1-888-8-Anybus

Fax: +1-312-629-2869 Fax: +1-312-629-2869

Online: www.anybus.com Online: www.anybus.com

HMS Germany

E-mail: [email protected] E-mail: [email protected]

Phone: +49 (0) 721-989777-000 Phone: +49 (0) 721-989777-000

Fax: +49 (0) 721-989777-010 Fax: +49 (0) 721-989777-010

Online: www.anybus.de Online: www.anybus.de

HMS Japan

E-mail: [email protected] E-mail: [email protected]

Phone: +81 (0) 45-478-5340 Phone: +81 (0) 45-478-5340

Fax: +81 (0) 45-476-0315 Fax: +81 (0) 45-476-0315

Online: www.anybus.jp Online: www.anybus.jp

HMS China

E-mail: [email protected] E-mail: [email protected]

Phone: +86 (0) 10-8532-3183 Phone: +86 (0) 10-8532-3023

Fax: +86 (0) 10-8532-3209 Fax: +86 (0) 10-8532-3209

Online: www.anybus.cn Online: www.anybus.cn

HMS Italy

E-mail: [email protected] E-mail: [email protected]

Phone: +39 039 59662 27 Phone: +39 039 59662 27

Fax: +39 039 59662 31 Fax: +39 039 59662 31

Online: www.anybus.it Online: www.anybus.it

HMS France

E-mail: [email protected] E-mail: [email protected]

Phone: +33 (0) 3 68 368 034 Phone: +33 (0) 3 68 368 033

Fax: +33 (0) 3 68 368 031 Fax: +33 (0) 3 68 368 031

Online: www.anybus.fr Online: www.anybus.fr

HMS UK & Eire

E-mail: [email protected]m E-mail: [email protected]

Phone: +44 (0) 1926 405599 Phone: +46 (0) 35 - 17 29 20

Fax: +44 (0) 1926 405522 Fax: +46 (0) 35 - 17 29 09

Online: www.anybus.co.uk Online: www.anybus.com

HMS Denmark

E-mail: [email protected]m E-mail: [email protected]

Phone: +45 (0) 35 38 29 00 Phone: +46 (0) 35 - 17 29 20

Fax: +46 (0) 35 17 29 09 Fax: +46 (0) 35 - 17 29 09

Online: www.anybus.com Online: www.anybus.com

HMS India

E-mail: [email protected] E-mail: [email protected]

Phone: +91 (0) 20 40111201 Phone: +91 (0) 20 40111201

Fax: +91 (0) 20 40111105 Fax: +91 (0) 20 40111105

Online: www.anybus.com Online: www.anybus.com

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Chapter 1

1. About the Anybus Communicator CAN

1.1 Introduction

The Anybus Communicator CAN is a series of products that acts as a gateway between a subnetwork,

running the standard CAN protocol, and a number of popular industrial networks. Integration of indus-

trial devices is enabled without loss of functionality, control and reliability, both when retro-fitting to

existing equipment as well as when setting up new installations.

The Anybus Communicator CAN is based on patented Anybus technology, a proven industrial commu-

nication solution used all over the world by leading manufacturers of industrial automation products.

Each module offers integration of industrial CAN devices to one of these industrial networks: Ether-

CAT, PROFIBUS, ControlNet, Modbus-RTU, Modbus-TCP, PROFINET, PROFINET IRT, Ether-

Net/IP, DeviceNet CC-Link and CANopen. The scope of this manual is the Anybus Communicator

CAN for EtherCAT. The manual primarily describes the functionality and the configuration of the CAN

network and the connection between the CAN network and the EtherCAT network. Relevant informa-

tion on the EtherCAT interface of the module is given, with the intention to facilitate the configuration

of the interface into a EtherCAT network. For more information about EtherCAT, please refer to offi-

cial specifications.

No proprietary configuration software is needed. All necessary configuration is performed using the

Anybus Configuration Manager that accompanies the product.

PC configuration

and monitoring

Fieldbus Control System

(e.g a PLC)

CAN communication devices

IN

VE

RT

ER

HM

I

Multi-Node Standard CAN NetworkSingle-Node Standard CAN Network

PC configuration

and monitoring

Fieldbus Control System

(e.g a PLC)

CAN communication

device

IN

VE

RT

ER

HM

I

(Fieldbus Network)

About the Anybus Communicator CAN 5

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Subnetwork

The Anybus Communicator CAN recognizes and supports communication that conforms to the CAN

standards 2.0A and 2.0B. The Communicator can adapt to any predefined network using CAN frames

as means for data exchange, using the Anybus Configuration Manager tool, that is included with the

product.

• 0 - 8 bytes of data in each frame

• 11-bit (CAN 2.0A) identifier or 29-bit (CAN 2.0B) identifier

• Bit rates supported: 20, 50, 100, 125, 200, 250, 500, 800 and 1000 kbit/s.

EtherCAT Interface

EtherCAT connectivity is provided through patented Anybus technology:

• EtherCAT over CANopen

• DS301 v4.02 compliant

• EMCY support

• Supports segmented SDO access

• Up to 512 bytes of cyclic data in each direction

1.2 Anybus Communicator CAN Concept

1.2.1 General

The Anybus Communicator is designed to exchange data between a subnetwork, running CAN, and a

higher level network. The CAN protocol uses frames, that are individually configurable, offering great

flexibility.

Through the configuration of the CAN frames, the Communicator will adapt to a predefined CAN net-

work. It will be possible to send data to and receive data from the subnetwork, but also to act as a relay

for data on the CAN subnetwork.

The Communicator can issue frames cyclically, on change of data, or based on trigger events issued by

the control system of the higher level network (i.e. the fieldbus master or PLC) or by the CAN network.

It can also monitor certain aspects of the subnetwork communication and notify the higher level net-

work when data has changed.

An essential part of the Anybus Communicator package is the Anybus Configuration Manager, a Win-

dows™ application which is used to supply the Communicator with a description of the subnetwork

protocol. No programming skills are required; instead, a visual protocol description-system is used to

specify the different parts of the CAN frames.

About the Anybus Communicator CAN 6

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

1.2.2 Data Exchange Model

Internally, the data exchanged on the subnetwork, and

the data exchanged on the higher level network, resides

in the same memory.

This means that in order to exchange data with the sub-

network, the higher level network simply reads and

writes data to memory locations specified using the An-

ybus Configuration Manager. The very same memory

locations can then be exchanged on the subnetwork.

The internal memory buffer is divided into three areas

based on their function:

• Input Data (Up to 512 bytes)

This area can be read by the higher level net-

work.

• Output Data (Up to 512 bytes)

This area can be written to by the higher level

network.

• General Data

This area can not be accessed from the higher

level network, but may be used for transfers between individual nodes on the subnetwork, or as

a general “scratch pad” for data. The size of the General Data area is 1024 bytes. How much data

of the area that is used for subnetwork communication is decided by the configuration.

Memory Map

When building the subnetwork configuration using the Anybus Configuration Manager, the different ar-

eas described above are mapped to the memory locations (addresses) specified below.

General Data

Anybus Communicator CAN

Internal Memory

Input Data

(244 bytes)

CAN Network

Output Data

(244 bytes)

Higher Level Network

Input Data Output Data General Data

CAN network: CAN network: CAN network:

Fieldbus:

Write Only

Read Only

Write Only

Read/Write

- Fieldbus: Fieldbus:

0x000 0x200

0x0FF 0x2FF

0x400

0x7FF

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Chapter 2

2. About the Module

2.1 External view

A: Status LEDs

See also...

- “Status LEDs” on page 9

B: Fieldbus Specific Connectors and Switches

This connector (connectors) and, if available,

these switches are used to connect the Anybus

Communicator CAN module to the EtherCAT

network. They are described in “Ethernet Con-

nectors” on page 10.

C: USB connector

This connector is used for uploading and down-

loading the configuration and for software up-

grade of the module.

See also...

- “USB Connector” on page 10

D: CAN Connector

This connector is used to connect the commu-

nicator to the CAN network.

See also...

- “CAN Connector” on page 10

E: Power Connector

This connector is used to apply power to the communicator.

See also...

- “Power Connector” on page 11

F: DIN-rail Connector

The DIN-rail mechanism connects the communicator to PE (Protective Earth).

See also...

- “Mounting” on page 8

A

B

C

D

E

F

About the Module 8

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

2.2 Mounting

Perform the following steps when physically installing the Communicator:

1. Snap the Communicator on to the DIN-rail (See “External view” on page 7).

The DIN-rail mechanism works as follows:

To snap the Communicator on, first press the it downwards (1) to com-

press the spring in the DIN-rail mechanism, then push it against the

DIN-rail as to make it snap on (2).

To snap the Communicator off, push the it downwards (1) and pull it out

from the DIN-rail (2), as to make it snap off from the DIN-rail.

2. Connect the Communicator to the CAN network.

3. Connect the Communicator to the EtherCAT network.

4. Connect the power cable and apply power.

1

2

1

2

About the Module 9

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

2.3 Status LEDs

The status LEDs on the front indicate the status of the module as shown in the table below.

Status LEDs 1 - 4 indicate the status of the EtherCAT network and status LEDs

5 - 6 indicate the status of the CAN subnetwork and the device.

# State Status

1 - Run Off INIT state

Blingking green PRE-OPERATIONAL state

Single flash, green SAFE-OPERATIONAL state

Green OPERATIONAL state

2 - Err Off EtherCAT communication in working order

Blinking red General configuration error

Single flash, red EtherCAT state changed autonomously

Double flash red Sync manager watchdog timeout

Red Application watchdog timeout

3 - Link activity 1

4 - Link activity 2

Off No link sensed on port 1/2

Green Link sensed on port 1/2

Flickering green Exchanging packets on port 1/2

5 - CAN subnet-

work status

Off Power off/no CAN communication

Green Running with no transaction error/timeout

Flashing green Not all transactions have been executed at

least once since startup and no transaction

error/timeout has occurred.

Flashing red Transaction error/timeout or subnetwork

stopped

Red Fatal error

6 - Device status Off Power off

Alternating red/green Invalid or missing configuration

Green Operation mode Run

Flashing green Operation mode Idle

Red Fatal error

1

3

5

2

4

6

About the Module 10

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

2.4 Connectors

2.4.1 Ethernet Connectors

EtherCAT Ports 1 and 2

2.4.2 USB Connector

At the bottom of the module you find a USB connector used for software upgrade

of the module and for uploading and downloading configurations.

Note: USB is used for configuration and software upgrade only. Remove the USB

cable when the configuration of the module is finished.

2.4.3 CAN Connector

Next to the USB connector the CAN connector is found.

Pin no Description

1TD+

2TD-

3 RD+

4, 5, 7, 8 (not connected)

6 RD-

Housing Cable Shield

Pin no. Description

1 +5 V input

2 USBDM (USB communication signals)

3 USBDP (USB communication signals)

4 Signal GND

Housing Cable Shield

Pin no. Description

2CAN_L

5 Housing, CAN cable shield

7 CAN_H

1, 4, 8, 9 (not connected)

3, 6 CAN GND

2

1

18

1

2

34

15

96 (male)

About the Module 11

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

2.5 Power Connector

Notes:

• Use 60/75 or 75×C copper (CU) wire only.

• The terminal tightening torque must be between 5... 7 lbs-in (0.5... 0.8 Nm)

See also...

- “Power Supply” on page 50

Pin no. Description

1 +24V DC

2GND

12

About the Module 12

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

2.6 Software Installation

2.6.1 Anybus Configuration Manager

System Requirements

• Pentium 233 MHz or higher (300 MHz recommended)

• 64 MB RAM or more (128 MB recommended)

• Microsoft Windows XP, Windows Vista, or Windows 7

Installation

• Anybus Communicator CAN resource CD

Insert the CD and follow the onscreen instructions. If the installation does not start automatically

right-click on the CD-drive icon and select Explore. Execute ‘setup.exe’ and follow the onscreen

instructions.

• From website

Download and execute the self-extracting .exe file from the HMS website (www.anybus.com).

2.6.2 Firmware Update

Updates of the Communicator firmware will be published on the support pages at www.anybus.com.

Also available is the tool Firmware Download TP, that is used to download the updated firmware to the

Communicator.

Note: Before downloading the new firmware, save a copy of the configuration, as the configuration in

the module will be erased during the installation process of the new firmware. When download of the

firmware is finished, the configuration can be restored from the safety copy.

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Chapter 3

3. Getting Started

The purpose of this chapter is to give a short description of how to install the module and get it up and

running, transferring I/O data between the CAN network and the EtherCAT network. Before starting,

make sure that you have access to knowledge about the CAN protocol to be configured, e.g. access to

the CAN protocol specification.

Perform the following steps when installing the Communicator:

1. Download the Anybus Configuration Manager from the product pages at www.anybus.com or

copy it from the CD that accompanies the product. Install it on your PC.

2. Download the Device Description File for the EtherCAT module from the product pages at

www.anybus.com or copy it from the CD that accompanies the product.

3. Build your configuration in the Anybus Configuration Manager tool, for an example see “Con-

figuration Example” on page 52, for a description of the tool see chapters 7 to 12.

4. Connect the Communicator to your PC using the USB connector.

5. Connect the power cable and apply power.

6. Download the configuration from the Anybus Configuration Manager to the Communicator.

See “Online” on page 40.

7. Remove the USB cable, turn off the power and disconnect the power cable.

8. Snap the Communicator on to the DIN-rail (See “Mounting” on page 8).

9. Connect the Communicator to the CAN network with proper termination and shielding.

10. If necessary, configure the other nodes in the CAN network.

11. Connect the Communicator to the EtherCAT network.

12. Connect the power cable and apply power.

13. Install the Device Description File in the EtherCAT configuration tool.

14. Configure the EtherCAT network. Please adapt the configuration to the one stored in the Com-

municator.

Doc.Id. HMSI-168-58

Anybus Communicator CAN to EtherCAT

Doc.Rev. 1.11

Chapter 4

4. CAN Network Communication

4.1 General

The CAN protocol is message-based and offers the possibility to exchange up to 8 bytes of data in each

message. How these bytes are interpreted, is defined in each application. The CAN protocol is a trans-

parent protocol, meaning that it only acts as a data carrier, and it is up to the users (the application) to

define and interpret the data content of the messages.

Data on CAN is exchanged using frames. Each frame has a unique identifier for the data it exchanges.

The identifier also represents the message priority on the CAN network. The Anybus Communicator

CAN supports either 11-bit (CAN 2.0A) or 29-bit (CAN 2.0B) identifiers, depending on what is defined

during configuration.

CAN is essentially a produce-consume network, where all nodes listen to all messages. The devices rec-

ognize what data to collect by what identifier the CAN frame carries. The Communicator is also able to

act as a Master and issue queries that demand responses. It is possible to use both methods in the same

configuration of the module.

4.2 Types of Messages

The Anybus Communicator CAN features three different message types regarding the subnetwork com-

munication, called ‘Query/Response’, ‘Produce’ and ‘Consume’. Note that these messages only specify

the basic communication model, not the actual CAN protocol. All three types of messages can be used

in the same configuration.

4.2.1 Query-Response

The Communicator acts as a master on the subnetwork, and the CAN communication takes place in a

query-response fashion. The Communicator sends a query and expects an answer within the specified

timeout.

Subnetwork Devices

Gateway

Control System

Page is loading ...

Anybus AB7311 User manual

Anybus AB7311 User manual

Related papers

Other documents