Rust Buster RB6061 Installation guide

Brand
Rust Buster
Model
RB6061
Type
Installation guide

This manual is also suitable for

Rust Buster RB6061

Below you will find brief product information for Rust Buster RB6061. This product is a Jeep® 1984-’01 XJ Cherokee Center Unibody Stiffener. This is a kit that contains all the necessary parts and instructions to install center unibody stiffeners on your Jeep. These stiffeners are designed to improve the structural integrity of your Jeep's unibody, which can help to reduce body flex and improve handling. The kit includes two stiffeners, one for the driver's side and one for the passenger side. The stiffeners are made from 6061 aluminum and are designed to fit under the Jeep's transmission crossmember. The kit also includes all the necessary hardware and instructions for installation.

Rust Buster RB6061

Below you will find brief product information for Rust Buster RB6061. This product is a Jeep® 1984-’01 XJ Cherokee Center Unibody Stiffener. This is a kit that contains all the necessary parts and instructions to install center unibody stiffeners on your Jeep. These stiffeners are designed to improve the structural integrity of your Jeep's unibody, which can help to reduce body flex and improve handling. The kit includes two stiffeners, one for the driver's side and one for the passenger side. The stiffeners are made from 6061 aluminum and are designed to fit under the Jeep's transmission crossmember. The kit also includes all the necessary hardware and instructions for installation.

RB6061
Jeep® 1984-’01 XJ Cherokee
Center Unibody Stiffeners
606100
REQUIRED TOOLS
Jack Stands or Lift
Mig Welder
Paint/Primer
Locking Pliers
Hand Grinder
Cutting Wheel or Torch
Welding Gloves
Welding Hood/Shield
Clamps
Ear & Eye Protection
Sockets & Ratchet
Wrenches
Fire Extinguisher & Water
KIT CONTAINS
Center Unibody Stiffener (Diver &
Passenger)
QTY
1ea
RB6061
Jeep® 1984-’01 XJ Cherokee
Center Unibody Stiffeners
1 606100
1) PREPARING YOUR VEHICLE
Begin by disconnecting your battery prior to starting
your installation.
Inspect your vehicle for leaking fuel lines, fuel tank
and engine components. If you have fuel leaks
repair all leaks prior to starting your installation. If
your fuel tank is near your welding area remove
your tank prior to welding.
Remove all combustible items above the work area
such as seats, carpets, padding, etc.
Keep all flammable materials away from the
vehicle work area.
2) PREPARING YOUR WORKSTATION
Keep a fire extinguisher and water close by in the
case of fire and make sure you always have a
designated “Fire Watch” to assist during the cutting
or welding phases.
Abide by all apprenticed welding safety standards
and practices.
Always use appropriate welding eye protection, ear
protection, and work and fire safety gloves during
the installation and within the work area.
WARNING!
If you are unsure on how to perform the installation
or how to operate any of the required tools listed
above, it is HIGHLY advised that you enlist the work
of a certified welder/installer.
Failure to follow proper safety precautions and
instructions may result in serious injury. The user
assumes all liability when installing the product.
RB6061
Jeep® 1984-’01 XJ Cherokee
Center Unibody Stiffeners
2 606100
3) PREPARING FOR YOUR INSTALL
On the driver’s side, with a 13mm socket, remove
the two bolts securing the e-break bracket and push
it out of the way. The passenger side has no
obstacles.
Place a jack or jack stand slightly below the
transmission’s crossmember, and begin removing
the 2 bolts with a 15mm socket. The transmission
will fall.
Prepare your weld zone by scoring or grinding away
any rust and debris.
4) INSTALL
With the side’s respective part, place it up to the
body, under the crossmember, and line up the
frame holes.
With the help of a friend or a jack, hold the part into
place and begin c-clamping it to the rail, away from
the bend point.
With another jack, press against the part at the
bend point, ensuring the steel conforms to the
shape of the rail.
RB6061
Jeep® 1984-’01 XJ Cherokee
Center Unibody Stiffeners
3 606100
C-clamp the part at this point. Continue to shape
the part as needed, while adjusting clap points until
there are no gaps.
Slide the stiffener into place, ensuring that it passes
underneath the break line and fender bracket.
Ensure all the frame holes line up, there are no
gaps, and c-clamp it into place.
5) WELD
Utilizing proper safety precautions and welding
techniques, tack weld the part into place, remove
the C-clamps, and completely weld around all edges
and through all stitch weld slots.
Repeat on the opposite side.
6) PAINT AND PROTECT
Coat the part and work area with a primer or other
rust inhibitor to help prevent or reduce the risk of
rust formation.…
7) REASSEMBLE VEHICLE
Reinstall your transmission crossmember.
Reinstall your e-break bracket.
Reconnect your battery.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Rust Buster RB6061 Installation guide

Brand
Rust Buster
Model
RB6061
Type
Installation guide
This manual is also suitable for

Rust Buster RB6061

Below you will find brief product information for Rust Buster RB6061. This product is a Jeep® 1984-’01 XJ Cherokee Center Unibody Stiffener. This is a kit that contains all the necessary parts and instructions to install center unibody stiffeners on your Jeep. These stiffeners are designed to improve the structural integrity of your Jeep's unibody, which can help to reduce body flex and improve handling. The kit includes two stiffeners, one for the driver's side and one for the passenger side. The stiffeners are made from 6061 aluminum and are designed to fit under the Jeep's transmission crossmember. The kit also includes all the necessary hardware and instructions for installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents