Quoizel COR1611CU Installation guide

Brand
Quoizel
Model
COR1611CU
Type
Installation guide

This manual is also suitable for

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-COR1611
For Styles COR1611CU and COR1611K
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering June result.
A
Crossbar
Assembly
x1
E
Shade
x1
B
Socket
Assembly
x1
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
October2014
C
Longer Collar
x1
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar
Assembly (A). Attach the Crossbar
Assembly (A) to the Outlet Box with the
head of the Green Ground Screw facing
you. Secure it with Outlet Box Screws (not
included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
STEP 2 Fit Ceiling Canopy to
Crossbar Assembly
-
A.
eiling canopy on Socket
Assembly (B) to the
eiling canopy
Remove mounting balls from the
Crossbar Assembly (A). Fit the
c
Crossbar
Assembly (A) and secure with
mounting balls. Note: The
c
should be snug
on Socket
Assembly (B)
Mounting Screw
Hex Nut and
Lock Washer
B
Mounting Ball
Figure 2
A
against the and the mounting balls. Ifceiling not, adjust the length of
the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the ceiling canopy on Socket Assembly (B) is
secure, remove the mounting ball and ceiling canopy and proceed to
Step 3.
A
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers,wire cutters, wirestrippers, electricaltape, safety glasses.
BulbRecommended:
EstimatedAssemblyTime:
Preparation:
(1)Medium Basebulb 100W Maximum,Alternatebulb (1)23W CFL.
30-45minutes
Identifyand inspectall parts beforebeginning installation.Check package contentlist anddiagramsbelow tobe sureallparts are
present.If anyparts are missingor damaged,do not attemptto assemble,install,or operatethe fixture. Contactcustomer servicefor replacement
parts.
D
Shorter Collar
x1
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Figure 4
STEP 4 Install Socket Assembly-
A. Carefully tuck all wires into the
outlet box and position the ceiling
canopy of Socket Assembly (B)
over the outlet box. Align the holes
in the ceiling canopy with the
mounting screws. Attach Socket
Assembly (B) using the mounting
balls. Hand tighten until snug.
Mounting Screw
B
Mounting Ball
A
Figure 5
STEP 5 Install Shade and Bulb-
A. Place Key Holes side of Shade (E) over the socket. Pass Key Holes
on the Shade (E) over Mounting Balls and rotate the Shade (E) until
it is secured in place.
Bulb
B
C
D
E
Top View
Key Hole
Mounting
Ball
B. Place Longer Collar (C) over
socket and thread Short Collar
(D) to socket. Hand tighten until
snug.
C. This fixture uses standard bulb
with medium base. Maximum
100 watts. Insert bulb and screw
snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
1
2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
COR1611CU/COR1611K
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
NO.
1
FINISH: COPPER BRONZE/MYSTIC BLACK
G3858SH SHADE 1
6.5”
(1) 100W
Bulb
(Not Supplied)
Medium
Base
10.5”
9” Dia.
11.5” Dia.
7.5” Dia.
October2014
  • Page 1 1
  • Page 2 2

Quoizel COR1611CU Installation guide

Brand
Quoizel
Model
COR1611CU
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents