Cascade X2000 is a powerful grilling system that offers a wide range of cooking options. It features a roll top grill hood, a rotisserie kit, a grilling or cooking surface, a side shelf, a side burner with its own control knob, a rear infrared burner with its own control knob, main burners with their own control knobs, a drawer, a hood handle, a warming shelf, and a cart with doors. Cascade X2000 is designed for outdoor use only and requires a level surface to operate safely.
Cascade X2000 is a powerful grilling system that offers a wide range of cooking options. It features a roll top grill hood, a rotisserie kit, a grilling or cooking surface, a side shelf, a side burner with its own control knob, a rear infrared burner with its own control knob, main burners with their own control knobs, a drawer, a hood handle, a warming shelf, and a cart with doors. Cascade X2000 is designed for outdoor use only and requires a level surface to operate safely.
USE AND CARE MANUAL
FOR OUTDOOR USE ONLY
ALWAYS KEEP YOUR GRILL COVERED WHEN NOT IN USE
BEFORE YOU BEGIN – We’ve included easy-to-follow, step-by-step instructions which have been carefully written to
ensure quick assembly of your grill. Reading the instructions will be a time saver in the end.
YOU WILL NEED – A Phillips screwdriver, adjustable wrench, 1/2” wrench or socket and a 1/4” nut driver or socket will
be needed to assemble this grill. All other necessary hardware has been included.
X2000 Gas Grill - LP
Questions, Missing or Damaged part? DO NOT RETURN PRODUCT TO STORE
Were here to help. Just call 1-800-229-5647 or visit us at www.sureheat.com. For faster service,
have model number and serial number on hand when calling.
X2000
2
IMPORTANT SAFETY INFORMATION
- Read this manual carefully before using your grill to reduce the risk of fire, burn
hazard or other injury.
- Extreme care should be used because of the high temperatures produced by this
appliance. CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA
WHERE THE GRILL IS BEING OPERATED.
- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not
allow flammable materials to come in contact with grate, burner or hot surfaces.
- Use only outdoors and provide good ventilation to avoid carbon monoxide build-up which could result in injury or death.
- Do not repair or replace any part of this appliance unless it is specifically recommended in this manual. A qualified
service technician should conduct all other service.
- Follow the installation and servicing instructions provided with this product. Have your grill installed by a qualified
service technician.
- Locate the main gas supply valve so that you know how to shut the gas off to your grill.
- If you smell gas, make sure all gas connections are tight before operation. If you continue to smell gas call a
qualified technician.
- When lighting a burner, always pay close attention to what you are doing and be certain you are pushing the igniter
that lights the burner you intend on using.
- Always keep your face and body as far away as from the grill as possible when lighting to reduce the risk of burn.
- Extinguish all flames and do not smoke while engaging gas and igniting the grill.
- A minimum distance of at least 15" must be maintained from any combustible material on both sides and the back of
the grill. Do not place the grill under any overhead unprotected combustible construction.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
WARNING indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
NOTE indicates an important piece of information that needs to
be observed to ensure the proper operation of your grill.
INSTALLER: Please retain these instructions with the owner so that they may maintain them for
future reference.
DANGER
If you smell gas:
1. Shut off gas to the appliance
2. Extinguish any open flame
3. Open lid
4. If odor continues, keep away from the
appliance and immediately call your
gas supplier or your fire department.
WARNING
1. Do not store or use gasoline or other
flammable liquids or vapors in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
Table of Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Grill Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-17
Gas Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
Pre-Operation Leak Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Lighting The Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Using The Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Using The Rotisserie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Accessory Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
3
Please retain this manual for future reference
© 2007 Sure Heat Manufacturing All rights reserved
Congratulations on your purchase of a new grill! We are
very proud of our product and we are completely
committed to providing you with the best service
possible. Your satisfaction is our #1 priority.
Please read this Use & Care Manual very carefully. It
contains valuable information on how to properly
maintain your new grill.
We know you’ ll enjoy your new grill and thank you for
choosing our product. We hope you consider us for
future purchases.
PLEASE READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating
instructions for your model. Use your grill only as
instructed in this manual. These instructions are not
meant to cover every possible condition and situation
that may occur. Common sense and caution must be
practiced when installing, operating and maintaining any
appliance.
Please record your model and serial numbers below for
future reference. This information is found on the serial
plate located on the inside of the grill door.
NOTE: Use only soap and water to clean serial plate.
Model Number: ______________________________
Serial Number: ______________________________
Purchase Date: ______________________________
Gas Type: __________________________________
Please complete and mail in the Product
Registration Card included with your grill.
Questions?
1-800-229-5647
for written inquiries:
Sure Heat Manufacturing
3130 Moon Station Rd
Kennesaw, GA 30144
Please attach sales receipt here for
future reference.
Register Your Product
The PRODUCT REGISTRATION CARD
should be filled in completely, signed
and returned to Sure Heat Manufacturing.
AssemblyWelcome & Congratulations
4
Do not use the rotisserie in the rain.
Electrical Grounding Instructions
This appliance (rotisserie motor) is equipped with a
three-prong (grounding) plug for your protection
against shock hazard and should be plugged directly
into a properly grounded three-prong receptacle. Do
not cut or remove the grounding prong from this plug.
Keep any electrical supply cords and the fuel supply
hose away from any heated surfaces.
The Spare L.P. Gas Tank Barrier must be installed to
prevent storage of spare L.P. Gas Tanks. Failure to
comply with these instructions could result in a fire or
explosion that could cause serious bodily injury, death,
or property damage.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open grill hood.
4. If odor continues, immediately
call your gas supplier and local Fire Dept.
CALIFORNIA PROPOSITION 65 - WARNING: The
Burning of gas cooking fuels generates some
by products which are on the list of substances which are
known by the State of California to cause cancer or
reproductive harm. California law requires businesses to
warn customers of potential exposure to such substances.
To minimize exposure to these substances, always operate
this unit according to the use and care manual, provide
good ventilation when cooking with gas.
This appliance is not intended to be installed in or
on recreational vehicles or boats.
FOR OUTDOOR USE ONLY
DO NOT try lighting this appliance without reading the
“ LIGHTING INSTRUCTIONS” section of this manual.
FOR YOUR SAFETY
DO NOT store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
An LP cylinder not connected for use shall not be stored in
the vicinity of this or any other appliance.
TESTED IN ACCORDANCE WITH ANSI
Z21.58a-2006/CSA 1.6a STANDARD FOR OUTDOOR
COOKING GAS APPLIANCES. THIS GRILL IS FOR
OUTDOOR USE ONLY.
Installation must conform with local codes, this unit should
be installed in accordance with the National Fuel Gas Code
No. Z223.1/NFPA 54, National Gas and Propane Installation
Code, CSA B149.1 or Propane Storage and Handling Code,
B149.2
Never attach an unregulated gas line to the appliance.
Connection to an unregulated gas line can cause excessive
heat or fire.
Always have a qualified service technician perform difficult
conversions or modifications.
Do not use the grill in garages, breezeways, sheds or any
enclosed area. Never operate the grill in enclosed areas as
this could lead to a carbon monoxide buildup, which could
result in injury or death. Place the grill on a level surface.
Avoid moving the grill while it is operation.
NOTE: Do Not operate the main burners and infrared
back burner at the same time. This can cause warping of
the roll top grill hood.
General Safety Instructions
Grill Features
5
1. Roll Top Grill Hood
2. Rotisserie Kit
3. Grilling/Cooking Surface
4. Side Shelf
5. Control Knob: Rear Infrared Burner
6. Control Knobs: Main Burners
7. Drawer
8. Hood Handle
9. Warming Shelf
10. Rear Infrared Burner
11. Side Burner
12. Control Knob: Side Burner
13. Electronic Igniter: Main Burners, Side Burner
and Rear Infrared Burner
14. Cart with Doors
1
2
3
4
5
6
7
8
9
10
11
12
14
13
Getting Started
6
Assembly
7
1b
1c
1a
1d
STEP ONE
a. Use (2) Screws secure the Rubber Door
Stop on the Cart Base.
b. Set the Cart base on the floor and then lay the
Caster Assembly Left on the left side and the
Caster Assembly Right on the right side of the Cart
Base. The angled side of the Cart Base will be
towards the front of the base.
c. Pick up the left side of the Cart Base and set the
Caster Assembly Left in place by inserting the
attached bolts through the three (3) holes in the
Cart Base.
d. Pick up the right side of the Cart Base and set the
Caster Assembly right in place by inserting the
attached bolts through the three (3) holes in the
Cart Base.
Assembly
8
2a
2c
2d
2b
2f
2e
STEP TWO
a. Place the Cart Side Left onto the two (2) outer fixed
caster assembly bolts, make sure the large flange
is toward the front of the Cart Base.
b. Secure the Cart Side Leftt in place by hand
tightening nuts onto the caster assembly bolts.
c. Place the Cart Back onto the two (2) rear caster
assembly bolts.
d. Secure the Cart Back in place by hand tightening
the Caster Assembly Nuts onto the caster assembly bolts.
e. Place the Cart Side Right onto the two (2) outer
swivel caster assembly bolts, make sure the large
flange is toward the front of the Cart Base.
f. Secure the cart side right in place by hand
tightening nuts onto the caster assembly bolts.
Note: The Cart Back is covered by the card sides.
Assembly
9
The Spare L.P. Gas Tank
Barrier must be installed to
prevent storage of spare L.P. Gas Tanks.
Failure to comply with these instructions
could result in a fire or explosion that could
cause serious bodily injury, death, or
property damage.
3a
3e
3f
3d
STEP THREE
a. Press the cart sides back together making sure that the cart
side flanges cover the cart back flange.
b. Attach three (3) self tapping screws through the pre-drilled
holes on the Cart Side Left into the cart back. Repeat for Cart
Side Right.
c. Tighten all six (6) caster assembly nuts with a wrench.
d. Slide the Tank Tray out of the bracket, and place the it on the
Cart Base, the handle of the tray toward front of the Cart Base.
Attach three (3) self tapping screws through the pre-drilled holes
on the Left Bracket into the Cart Base. Repeat on the Bracket
Right. Then Slide the tray into the Bracket.
e. Attach the Spare L.P. Gas Tank Barrier by inserting the tabs
into the slots in the Cart Back and then attach the flat end of the
barrier to the pre-drilled hole in the Cart Back with a self-tapping
screw.
f. Attach the Tank Secure Ring onto the Cart Back.
Assembly
10
3c
3a
3a
3c
3b
STEP FOUR
a. Attaching (2) Self Tapping Screws through the pre-drilled
holes on the Left Bracket for the Cart Door Pin into the Cart Side
Left. Repeat on the Bracket Right.
b. Attaching (4) Self Tapping Screws through the pre-drilled
holes on the two Bracket for the Cart Door Magnet into the Cart
Cross Brace.
c. Install Cart Cross Brace onto the Cart Sides by secure (2) self
tapping screws though the pre drilled holes on each end of the
Cart Cross Brace into the top of the cart side flanges.
STEP FIVE
a. Use (2) self tapping screws to install the left drip pan guide in
position.
Note: The end with flange facing inside of the grill.
b. Repeat step 5a to install the right drip pan guide.
c. Use (6) screws to install the drawer guides in position.
Noto: The end connected with the cross bar facing inside of
the grill.
Assembly
11
5b
5a
5c
Assembly
12
6a
6b
6c-6d
6e
STEP SIX
a. Loosen the four (4) grill mounting bolts so that there is
approximately 1/4” between the bolt head and grill bottom.
b. Have someone help you pick up the grill and set it squarely on
top of the cart.
c. Make sure the four (4) bolts fall through the large opening on
the “ key hole” slots in the cart sides.
d. Slide the grill forward in the “ key hole” slots until the front
grill flange rests against the cart side flanges. Check on the
inside of the cart to make sure that both sides of the grill are
flush with the cart.
e. Install two (2) self tapping screws into the Cart Cross Brace to
secure the Drawer Guides in position..
f. Tighten the four (4) grill head mounting bolts underneath the
grill to secure the grill to the cart.
STEP SEVEN
a. Remove the screws from three handles.
b. Use (2) screws removed in step 7a to attach the handle onto
the cart door.
c. Repeat step 7b to install the handle to the other door.
d. Use (2) screws removed in step 7a to attach the handle onto
the front face of the drawer.
e. Use (5) self tapping screws to attach the drawer tray to the
drawer front face.
Assembly
13
step 7b - 7c
7d
7e
STEP EIGHT
a. Place a piece of Styrofoam from the packaging inside the roll
top grill hood to leave the hood propped open slightly.
b. Attach the left shelf by inserting the two shelf hooks into the
slots on the left side of the grill front face.
c. After inserting the two shelf hooks, press the shelf against the
grill and press downward until the shelf locks in place. Make
sure the top trim strip is hanging all the way inside of the grill
before pressing downward.
d. Install (2) screws through the hole on the back support
bracket of the left shelf into the cart side left. This will
permanently lock the shelf in place.
Assembly
14
close-up of step 8d
8a
8b
8c
STEP NINE
a. Place a piece of Styrofoam from the packaging inside the roll
top grill hood to leave the hood propped open slightly.
b. Attach the Right Shelf by inserting the two shelf hooks into the
slots on the right side of the grill front face.
c. After inserting the two shelf hooks, press the shelf against the
grill and press downward until the shelf locks in place. Make
sure the top trim strip is hanging all the way inside of the grill
before pressing downward.
d. Install (2) screws through the hole on the back support
bracket of the right shelf into the cart side left. This will
permanently lock the shelf in place.
Assembly
15
9b
9a
9c
close-up of step 9d
STEP TEN
a. Remove two screws from the burner valve assembly.
b. Carefully insert the valve assembly into the cast burner. You
will need to angle the tube into the burner assembly. Make
certain that the hose is pointing down when the valve is put in
place. Then push the valve stem out through the opening
in the front of the side burner shelf assembly, lining up the holes
on the valve assembly with the openings on the burner shelf.
c. Place bezel into place, with the "off" position pointing up, mak-
ing sure to line up holes.
d. Attach bezel to assembly face with screws removed in
step 10a.
e. Press knob onto valve assembly stem.
Assembly
16
close-up of step 10b
10b
10c
10e
STEP ELEVEN
a. Place the electronic igniter button into the igniter hole on the
front left of the side burner shelf.
b. Secure the igniter in place using the plastic lock nut. Make
sure to tighten securely.
c. Install AA battery, negative side first.
d. Install spring and cap assembly and tighten securely.
e. Attach the two igniter wires to the igniter button and igniter
module.
Note: Make sure you follow the left picture to attach them.
f. Attach loose wire to bottom of cast burner, and then to any of
the open tabs in the igniter. Insert the three igniter wires fed
through the grommeted hole on side of grill cart in Step 9 into
the remaining three holes.
Note: The igniter module is designed in such a way that it
does not matter which terminal tab is used when connecting
igniter wires.
Assembly
17
11a
11b
11c
11d
close-up of igniter wires attaching to igniter module
close-up of igniter wire attaching to burner
STEP TWELVE
a. Center the brass burner cap on top of the side
burner head.
b. Place the side burner grate on to the side
burner tray.
Assembly
18
12a
12b
Assembly
19
close-up of steps 13b - 13c
13b
13d
13a
STEP THIRTEEN
a. Place right hand door on an angle over the right side door
pivot.
b. Tilt the top of the door toward the grill, while depressing the
door pivot pin on the bracket.
c. Move the door slightly until the pin locks into place in the hole
on the top of the Cart Door Right.
d. Repeat steps 13a - 13c for left door installation.
Assembly
20
STEP FOURTEEN
a. Slide the drawer assembled in step 7d - 7e into the drawer
guides under the front face. Make sure the little wheels on the
side of the drawer move on the drawer guides.
b. Slide drip pan in place through the hole on the cart back.
step 14b
step 14a
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
Cascade X2000 is a powerful grilling system that offers a wide range of cooking options. It features a roll top grill hood, a rotisserie kit, a grilling or cooking surface, a side shelf, a side burner with its own control knob, a rear infrared burner with its own control knob, main burners with their own control knobs, a drawer, a hood handle, a warming shelf, and a cart with doors. Cascade X2000 is designed for outdoor use only and requires a level surface to operate safely.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Sonoma SGR30M Owner's manual
-
Amana AM33LP Owner's manual
-
Electrolux EGL3000X User manual
-
-
Four Seasons FS388LP1 Owner's manual
-
Surefire SF34LP User guide
-
Garth Side Operating instructions
-
-
Black Bull 806311 User manual
-
