Extron Fiber Matrix 6400 User manual

Extron
Brand
Extron
Model
Fiber Matrix 6400
Category
Network switches
Type
User manual

This manual is also suitable for

Extron Fiber Matrix 6400 3G HD-SDI I/O Board is a hot-swappable input/output board designed for use with the Extron Fiber Matrix 6400. The board supports 3G HD-SDI, HD-SDI, and SDI video formats and can be used for a variety of applications, including video distribution, signal processing, and remote monitoring.

The board features eight BNC connectors, which can be used for input or output connections. The board also includes two SFP+ cages, which can be used to connect to fiber optic cables. The board is compatible with a variety of SFP+ transceivers, which allows it to be used with a variety of fiber optic cables and distances.

Extron Fiber Matrix 6400 3G HD-SDI I/O Board is a hot-swappable input/output board designed for use with the Extron Fiber Matrix 6400. The board supports 3G HD-SDI, HD-SDI, and SDI video formats and can be used for a variety of applications, including video distribution, signal processing, and remote monitoring.

The board features eight BNC connectors, which can be used for input or output connections. The board also includes two SFP+ cages, which can be used to connect to fiber optic cables. The board is compatible with a variety of SFP+ transceivers, which allows it to be used with a variety of fiber optic cables and distances.

68-1371-30
Rev. A 05 08
Fiber Matrix 6400 Input/Output Board
Installation Instructions
Removing the I/O board or blank panel
Remove an I/O board or blank panel as follows:
N The I/O boards are hot-swappable. You do not need to power
down the switcher to remove an I/O board.
1. For an I/O board, disconnect any connected cables.
2. Rotate the left and right knurled knobs to completely loosen
the captive screws.
3. Gently pull on the knurled knobs/captive screws to loosen
the board or panel from the backplane.
4. Slide the board or panel out of the chassis (see the illustration
on the other side of this card).
C Do not touch the electronic components or the connectors
on the backplane or on the circuit boards without being
electrically grounded. Handle circuit boards by their edges
only. ESD can damage ICs, even if you cannot feel, see, or
hear it.
5. Place the removed board on an anti-static surface or in an
anti-static container.
Installing the I/O board
Install an I/O board as follows:
N The I/O boards are hot-swappable. You do not need to power
down the switcher to install an I/O board.
C Do not touch the electronic components or the connectors
on the backplane or on the circuit boards without being
electrically grounded. Handle circuit boards by their edges
only. ESD can damage ICs, even if you cannot feel, see, or
hear it.
1. Orient the board to be installed so that transceiver module A
(fiber board) or input BNC A (SDI/HD-SDI board) is on the
left and transceiver module or output BNC H is on the right.
2. Align the board with the left and right chassis guides (see the
illustration on the other side of this card).
3. Gently slide the board into the enclosure. Slide the board
toward the front panel until it meets resistance.
4. Gently seat the board in the backplane.
5. Tighten the left and right knurled knobs/captive screws to
lock the board or panel in place.
N If necessary, use a screwdriver to tighten the knurled knobs/
captive screws.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
www.extron.com
Fiber Matrix 6400 Input/Output Board
Installation Instructions (Continued)
100-240V 50/60Hz
1.2A MAX.
100-240V 50/60Hz
1.2A MAX.
REDUNDANT
PRIMARY
1 - 8
9 - 16
17 - 24
25 - 3233 - 40
41 - 48
49 - 5657 - 64
LAN
ACT
LINK
RESET
ANAHEIM, CA
PRIMARY POWER SUPPLY
REDUNDANT POWER SUPPLY
Align with Plastic Guides
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
IN
MUTI-RATE SDI INPUTS
H
G
A D
E
F
C
B
MUTI-RATE SDI OUTPUTS
H
G
A D
E
F
C
B
  • Page 1 1

Extron Fiber Matrix 6400 User manual

Extron
Brand
Extron
Model
Fiber Matrix 6400
Category
Network switches
Type
User manual
This manual is also suitable for

Extron Fiber Matrix 6400 3G HD-SDI I/O Board is a hot-swappable input/output board designed for use with the Extron Fiber Matrix 6400. The board supports 3G HD-SDI, HD-SDI, and SDI video formats and can be used for a variety of applications, including video distribution, signal processing, and remote monitoring.

The board features eight BNC connectors, which can be used for input or output connections. The board also includes two SFP+ cages, which can be used to connect to fiber optic cables. The board is compatible with a variety of SFP+ transceivers, which allows it to be used with a variety of fiber optic cables and distances.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents