Hitachi IC35L180AVV207 Datasheet

Category
Internal hard drives
Type
Datasheet
Hard disk drive specifications
Deskstar 180 GXP
3.5 inch Ultra ATA/100 hard disk drive
IC35L030AVV207
IC35L060AVV207
IC35L090AVV207
IC35L120AVV207
IC35L180AVV207
Models:
Revision 4.2 30 April 2003
S08-K0000-06 Publication #2840
Hard disk drive specifications
Deskstar 180 GXP
3.5 inch Ultra ATA/100 hard disk drive
IC35L030AVV207
IC35L060AVV207
IC35L090AVV207
IC35L120AVV207
IC35L180AVV207
Models:
Revision 4.2 30 April 2003
S08-K0000-06 Publication #2840
1st Edition (Revision 1.0) S-08K-0000-00 (18 December 2001) Preliminary
2nd Edition (Revision 2.0) S-08K-0000-00 (18 April 2002) Preliminary
3rd Edition (Revision 2.1) S-08K-0000-00 (21 June 2002) Preliminary
4rd Edition (Revision 2.2) S-08K-0000-00 (25 July 2002) Preliminary
5th Edition (Revision 2.3) S-08K-0000-01 (01 August 2002) Preliminary
6th Edition (Revision 2.5) S-08K-0000-02 (06 August 2002) Preliminary
7th Edition (Revision 3.0) S-08K-0000-03 (16 August 2002) Preliminary
8th Edition (Revision 4.0) S-08K-0000-04 (30 September 2002) Release
9th Edition (Revision 4.1) S-08K-0000-05 (08 January 2003) Revision
10th Edition (Revision 4.2) S-08K-0000-06 (30 April 2003) Revision
The following paragraph does not apply to the United Kingdom or any country where such provisions are
inconsistent with local law: HITACHI GLOBAL STORAGE TECHNOLOGIES PROVIDES THIS PUB-
LICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, IN-
CLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer or express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in new editions of the publication. Hitachi may make
improvements or changes in any products or programs described in this publication at any time.
It is possible that this publication may contain reference to, or information about, Hitachi products (machines and
programs), programming, or services that are not announced in your country. Such references or information must
not be construed to mean that Hitachi intends to announce such Hitachi products, programming, or services in your
country.
Technical information about this product is available by contacting your local Hitachi Global Storage Technologies
representative or on the Internet at http://www.hgst.com
Hitachi Global Storage Technologies may have patents or pending patent applications covering subject matter in
this document. The furnishing of this document does not give you any license to these patents.
©Copyright Hitachi Globlal Storage Technologies
Note to U.S. Government Users —Documentation related to restricted rights —Use, duplication or disclosure is
subject to restrictions set forth in GSA ADP Schedule Contract with Hitachi Global Storage Technologies.
Table of contents
476.5 DC power requirements .......................................................
466.4.2 Corrosion test ..........................................................
456.4.1 Temperature and humidity ...............................................
456.4 Environment ................................................................
416.3.4 Jumper positions .......................................................
406.3.3 Jumper pin assignment ..................................................
396.3.2 Jumper pin identification .................................................
396.3.1 Jumper pin location .....................................................
396.3 Jumper settings ..............................................................
386.2.6 Cabling ................................................................
386.2.5 Addressing of registers ..................................................
306.2.4 Ultra DMA timings ......................................................
296.2.3 Multiword DMA timings ..................................................
276.2.2 PIO timings ............................................................
266.2.1 Reset timings ..........................................................
266.2 Signal timings ...............................................................
256.1.3 Interface logic signal levels ...............................................
226.1.2 Signal definition ........................................................
216.1.1 Connector location ......................................................
216.1 Electrical interface ...........................................................
21
6.0 Specification
...............................................................
19
5.0 Defect flagging strategy
....................................................
174.4.6 Operating modes .......................................................
164.4.5 Throughput ............................................................
154.4.4 Data transfer speed .....................................................
144.4.3 Drive ready time ........................................................
124.4.2 Mechanical positioning ..................................................
124.4.1 Command overhead ....................................................
124.4 Performance characteristics ...................................................
114.3.2 Cylinder allocation ......................................................
114.3.1 Drive format ............................................................
114.3 Drive organization ............................................................
104.2 Data sheet ..................................................................
94.1 Default logical drive parameters ..................................................
9
4.0 Drive characteristics
..........................................................
73.3 Actuator ......................................................................
73.2 Head disk assembly ............................................................
73.1 Control Electronics .............................................................
7
3.0 Fixed disk subsystem description
.............................................
5
Part 1. Functional specification
..............................................
3
2.0 General features
.............................................................
11.3 References ...................................................................
11.2 General caution ................................................................
11.1 Glossary ......................................................................
1
1.0 General
......................................................................
xi
List of figures
...................................................................
Deskstar 180GXP hard disk drive specifications
v
708.13 Status Register .............................................................
698.12 Sector Number Register .....................................................
698.11 Sector Count Register .......................................................
698.10 Features Register ...........................................................
688.9 Error Register ...............................................................
688.8 Device/Head Register ........................................................
678.7 Drive Address Register .......................................................
678.6 Device Control Register ......................................................
678.5 Data Register ...............................................................
668.4 Cylinder Low Register ........................................................
668.3 Cylinder High Register .......................................................
668.2 Command Register ..........................................................
668.1 Alternate Status Register .....................................................
65
8.0 Registers
..................................................................
637.2 Deviations from standard .....................................................
637.1 Terminology .................................................................
63
7.0 General
....................................................................
61
Part 2. Interface specification
..............................................
606.12.2 C-Tick Mark ...........................................................
606.12.1 CE Mark ..............................................................
606.12 Electromagnetic compatibility .................................................
596.11.6 Secondary circuit protection .............................................
596.11.5 Environment ..........................................................
596.11.4 Safe handling .........................................................
596.11.3 Flammability ..........................................................
596.11.2 German Safety Mark ...................................................
596.11.1 UL and CSA standard conformity ........................................
596.11 Safety .....................................................................
586.10 Identification labels ..........................................................
576.9 Acoustics ...................................................................
566.8.5 Nonoperating Rotational shock ...........................................
566.8.4 Nonoperating shock .....................................................
566.8.3 Operating shock ........................................................
556.8.2 Nonoperating vibration ..................................................
556.8.1 Operating vibration ......................................................
556.8 Vibration and shock ..........................................................
546.7.5 Heads unload and actuator lock ..........................................
546.7.4 Drive mounting .........................................................
546.7.3 Connector locations .....................................................
536.7.2 Hole locations ..........................................................
516.7.1 Physical dimensions ....................................................
516.7 Mechanical specifications .....................................................
506.6.6 Required Power-Off Sequence ...........................................
506.6.5 Data reliability ..........................................................
506.6.4 Preventive maintenance .................................................
506.6.3 Start/stop cycles ........................................................
506.6.2 Cable noise interference .................................................
506.6.1 Data integrity ...........................................................
506.6 Reliability ...................................................................
496.5.3 Power supply generated ripple at drive power connector .....................
476.5.2 Power supply current (typical) ............................................
476.5.1 Input voltage ...........................................................
Deskstar 180GXP hard disk drive specifications
vi
11111.2.4 DEVICE CONFIGURATION SET (subcommand C3h) .....................
11111.2.3 DEVICE CONFIGURATION IDENTIFY (subcommand C2h) ................
11111.2.2 DEVICE CONFIGURATION FREEZE LOCK (subcommand C1h) ...........
11011.2.1 DEVICE CONFIGURATION RESTORE (subcommand C0h) ...............
11011.2 Device Configuration Overlay (B1h) ..........................................
10911.1 Check Power Mode (E5h/98h) ...............................................
105
11.0 Command descriptions
...................................................
10310.5 DMA queued commands ....................................................
10210.4 DMA commands ...........................................................
10010.3 Non-data commands .......................................................
9810.2 PIO Data Out commands ....................................................
9610.1 PIO Data In commands ......................................................
95
10.0 Command Protocol
........................................................
939.16 48-bit Address Feature Set ..................................................
929.15.3 Exceptions in Address Offset Mode ......................................
929.15.2 Identify Device Data ....................................................
919.15.1 Enable/Disable Address Offset Mode .....................................
919.15 Address Offset Feature ......................................................
919.14 Automatic Acoustic Management feature set (AAM) .............................
909.13 Advanced Power Management feature set (APM) ...............................
909.12 Power-Up In Standby feature set ..............................................
899.11.1 Auto Reassign function .................................................
899.11 Reassign function ...........................................................
899.10 Write cache function .........................................................
889.9 Seek Overlap ................................................................
879.8.2 Security extensions .....................................................
869.8.1 Example for operation (in LBA mode) ......................................
869.8 Host Protected Area Function ..................................................
849.7.5 Command table ........................................................
819.7.4 Operation example ......................................................
809.7.3 Passwords .............................................................
809.7.2 Security level ...........................................................
809.7.1 Security mode ..........................................................
809.7 Security Mode Feature Set ....................................................
799.6.8 Self-test ...............................................................
789.6.7 Error log ...............................................................
789.6.6 Off-line read scanning ...................................................
789.6.5 S.M.A.R.T. commands ..................................................
789.6.4 Threshold Exceeded Condition ...........................................
789.6.3 Attribute thresholds .....................................................
789.6.2 Attribute values .........................................................
789.6.1 Attributes ..............................................................
789.6 S.M.A.R.T. function ..........................................................
779.5.4 Interface capability for power modes ......................................
769.5.3 Standby timer ..........................................................
769.5.2 Power management commands ..........................................
769.5.1 Power modes ..........................................................
769.5 Power management feature ...................................................
759.4 Overlapped and queued feature ................................................
749.3.2 LBA Addressing Mode ...................................................
749.3.1 Logical CHS Addressing Mode ...........................................
749.3 Sector Addressing Mode ......................................................
739.2 Diagnostic and reset considerations ............................................
729.1.1 Register initialization ....................................................
719.1 Reset response .............................................................
719.0 General operation ..........................................................
Deskstar 180GXP hard disk drive specifications
vii
20011.42.5 SMART summary error log sector ......................................
19911.42.4 SMART Log Directory ................................................
19811.42.3 Device Attribute Thresholds Data Structure .............................
19411.42.2 Device Attributes Data Structure .......................................
19011.42.1 S.M.A.R.T. Subcommand .............................................
18911.42 S.M.A.R.T. Function Set (B0h) ..............................................
18811.41 Sleep (E6h/99h) ..........................................................
18711.40 Set Multiple (C6h) .........................................................
18511.39 Set Max Address Ext (37h) .................................................
18411.38.4 Set Max Freeze Lock (Feature = 04h) ..................................
18311.38.3 Set Max Unlock (Feature = 03h) .......................................
18211.38.2 Set Max Lock (Feature = 02h) .........................................
18111.38.1 Set Max Set Password (Feature = 01h) .................................
17911.38 Set Max Address (F9h) ....................................................
17711.37.4 Automatic Acoustic Management ......................................
17611.37.3 Advanced Power Management ........................................
17611.37.2 Write Cache ........................................................
17611.37.1 Set Transfer mode ...................................................
17511.37 Set Features (EFh) ........................................................
17411.36 Service (A2h) ............................................................
17311.35 Seek (7xh) ...............................................................
17111.34 Security Unlock (F2h) .....................................................
16911.33 Security Set Password (F1h) ...............................................
16811.32 Security Freeze Lock (F5h) ................................................
16611.31 Security Erase Unit (F4h) ..................................................
16511.30 Security Erase Prepare (F3h) ...............................................
16411.29 Security Disable Password (F6h) ...........................................
16311.28 Recalibrate (1xh) .........................................................
16111.27 Read Verify Sector(s) Ext (42h) .............................................
15911.26 Read Verify Sector(s) (40h/41h) ............................................
15711.25 Read Sector(s) Ext (24h) ..................................................
15511.24 Read Sector(s) (20h/21h) ..................................................
15411.23 Read Native Max Address Ext (27h) ........................................
15311.22 Read Native Max Address (F8h) ............................................
15111.21 Read Multiple Ext (29h) ....................................................
14911.20 Read Multiple (C4h) .......................................................
14711.19 Read Long (22h/23h) ......................................................
14511.18.3 Extended Self-test log sector ..........................................
14211.18.2 Extended Comprehensive SMART Error log .............................
14111.18.1 General Purpose Log Directory ........................................
14011.18 Read Log Ext (2Fh) .......................................................
13811.17 Read DMA Queued Ext (26h) ..............................................
13611.16 Read DMA Queued (C7h) ..................................................
13411.15 Read DMA Ext (25h) ......................................................
13211.14 Read DMA (C8h/C9h) .....................................................
13111.13 Read Buffer (E4h) ........................................................
13011.12 NOP (00h) ...............................................................
12911.11 Initialize Device Parameters (91h) ...........................................
12811.10 Idle Immediate (E1h/95h) ..................................................
12711.9 Idle (E3h/97h) .............................................................
12011.8 Identify Device (ECh) .......................................................
11911.7 Format Unit (F7h) ..........................................................
11711.6 Format Track (50h) ........................................................
11611.5 Flush Cache Ext (EAh) .....................................................
11511.4 Flush Cache (E7h) .........................................................
11411.3 Execute Device Diagnostic (90h) .............................................
Deskstar 180GXP hard disk drive specifications
viii
231
Index
.........................................................................
229
12.0 Timings
.................................................................
22711.55 Write Sector(s) Ext (34h) ...................................................
22511.54 Write Sector(s) (30h/31h) ..................................................
22311.53 Write Multiple Ext (39h) ....................................................
22111.52 Write Multiple (C5h) .......................................................
21911.51 Write Long (32h/33h) ......................................................
21711.50 Write Log Ext (3Fh) .......................................................
21511.49 Write DMA Queued Ext (36h) ...............................................
21311.48 Write DMA Queued (CAh/CBh) .............................................
21111.47 Write DMA Ext (35h) ......................................................
20911.46 Write DMA (CAh/CBh) .....................................................
20811.45 Write Buffer (E8h) .........................................................
20711.44 Standby Immediate (E0h/94h) ..............................................
20511.43 Standby (E2h/96h) ........................................................
20411.42.7 Error reporting ......................................................
20311.42.6 Self-test log data structure ............................................
Deskstar 180GXP hard disk drive specifications
ix
This page intentionally left blank.
List of figures
46Figure 52. Limits of temperature and humidity ........................................
45Figure 51. Temperature and humidity ...............................................
44Figure 50. Jumper settings for Disabling Auto Spin ...................................
43Figure 49. Jumper positions for capacity clip to 2GB/32GB ............................
42Figure 48. Jumper positions for 15 logical head default ...............................
41Figure 47. Jumper positions for normal use ..........................................
40Figure 46. Jumper pin assignment .................................................
39Figure 45. Jumper pin identification (2- and 3-disk model shown) .......................
39Figure 44. Jumper pin location (2- and 3-disk model shown) ...........................
38Figure 43. I/O address map .......................................................
37Figure 42. Ultra DMA cycle timings (Host Terminating Write) ...........................
37Figure 41. Ultra DMA cycle timing chart (Host Terminating Write) .......................
36Figure 40. Ultra DMA cycle timings (Device terminating Write) .........................
36Figure 39. Ultra DMA cycle timing chart (Device Terminating Write) .....................
35Figure 38. Ultra DMA cycle timings (Device Pausing Write) ............................
35Figure 37. Ultra DMA cycle timing chart (Device Pausing Write) ........................
34Figure 36. Ultra DMA cycle timings (Initiating Write) ..................................
34Figure 35. Ultra DMA cycle timing chart (Initiating Write) ..............................
33Figure 34. Ultra DMA cycle timings (Device Terminating Read) .........................
33Figure 33. Ultra DMA cycle timing chart (Device terminating Read) .....................
32Figure 32. Ultra DMA cycle timings (Host terminating Read) ...........................
32Figure 31. Ultra DMA cycle timing chart (Host terminating Read) .......................
31Figure 30. Ultra DMA cycle timings (Host pausing Read) ..............................
31Figure 29. Ultra DMA cycle timing chart (Host pausing Read) ..........................
30Figure 28. Ultra DMA cycle timings (Initiating Read) ..................................
30Figure 27. Ultra DMA cycle timing chart (Initiating Read) ..............................
29Figure 26. Multiword DMA cycle timings .............................................
29Figure 25. Multiword DMA cycle timing chart .........................................
27Figure 24. PIO cycle timings .......................................................
27Figure 23. PIO cycle timings chart ..................................................
26Figure 22. System reset timing .....................................................
26Figure 21. System reset timing chart ................................................
22Figure 20. Signal special definitions for Ultra DMA ....................................
22Figure 19. Table of signals ........................................................
21Figure 18. Power connector pin assignments ........................................
21Figure 17. Connector location (2- and 3-disk model shown) ............................
19Figure 16. PList physical format ....................................................
17Figure 15. Mode transition times ...................................................
16Figure 14. Random Access Performance ............................................
16Figure 13. Simple Sequential Access performance ...................................
15Figure 12. Data transfer speed .....................................................
14Figure 11. Drive ready time ........................................................
14Figure 10. Latency Time ..........................................................
14Figure 9. Single Track Seek Time ..................................................
14Figure 8. Cylinder switch time .....................................................
13Figure 7. Head switch time ........................................................
13Figure 6. Full stroke seek time .....................................................
12Figure 5. Mechanical positioning performance .......................................
12Figure 4. Command overhead ....................................................
11Figure 3. Cylinder allocation .......................................................
10Figure 2. Mechanical positioning performance .......................................
9Figure 1. Formatted capacity ........................................................
Deskstar 180GXP hard disk drive specifications
xi
127Figure 107. Idle Command (E3h/97h) ..............................................
126Figure 106. Identify Device Information (part 6 of 6) ..................................
125Figure 105. Identify Device Information (part 5 of 6) ..................................
124Figure 104. Identify Device Information (part 4 of 6) ..................................
123Figure 103. Identify Device Information (part 3 of 6) ..................................
122Figure 102. Identify Device Information (part 2 of 6) ..................................
121Figure 101. Identify Device Information (part 1 of 6) .................................
120Figure 100. Identify Device Command (ECh) .......................................
119Figure 99. Format Unit Command (F7h) ............................................
117Figure 98. Format Track Command (50h) ..........................................
116Figure 97. Flush Cache Ext Command (EAh) .......................................
115Figure 96. Flush Cache Command (E7h) ...........................................
114Figure 95. Execute Device Diagnostic Command (90h) ..............................
113Figure 94. DCO error information definition .........................................
112Figure 93. Device Configuration Overlay Data structure ..............................
110Figure 92. Device Configuration Overlay Features register values .....................
110Figure 91. Device Configuration Overlay Command (B1h) ............................
109Figure 90. Check Power Mode Command (E5h/98h) .................................
107Figure 89. Command set (Subcommands) .........................................
106Figure 88. Command set (2 of 2) ..................................................
105Figure 87. Command set (1 of 2) ..................................................
92Figure 86. Device address map before and after Set Feature ..........................
88Figure 85. Seek overlap ..........................................................
85Figure 84. Command table for device lock operation (part 2 of 2) ......................
84Figure 83. Command table for device lock operation (part 1 of 2) .......................
83Figure 82. Password Lost .........................................................
82Figure 81. Usual Operation ........................................................
81Figure 80. Initial Setting ...........................................................
77Figure 79. Power conditions .......................................................
73Figure 78. Reset error register values ...............................................
72Figure 77. Diagnostic Codes ......................................................
72Figure 76. Default Register Values .................................................
71Figure 75. Reset Response Table ..................................................
70Figure 74. Status Register ........................................................
68Figure 73. Error Register ..........................................................
68Figure 72. Device/Head Register ...................................................
67Figure 71. Drive Address Register ..................................................
67Figure 70. Device Control Register .................................................
66Figure 69. Alternate Status Register ................................................
65Figure 68. Register Set ...........................................................
57Figure 67. Sound power levels .....................................................
56Figure 66. Rotational Shock .......................................................
56Figure 65. Sinusoidal shock wave ..................................................
55Figure 64. Random vibration PSD profile break points (nonoperating) ...................
55Figure 63. Random vibration PSD profile break points (operating) ......................
54Figure 62. Connector locations ....................................................
53Figure 61. Mounting hole locations .................................................
52Figure 60. Physical Dimensions ....................................................
52
Figure 59. Bottom and side views of 30GB - 60GB models with breather hole and
mounting hole locations .......................................................
51Figure 58. Top and side views of 80 GB - 180 GB models with mechanical dimensions ....
49Figure 57. Power supply generated ripple at drive power connector .....................
48Figure 56. Power supply current of 60 GB, 40GB, and 30 GB models ...................
48Figure 55. Power supply current of 80 GB and 120 GB models .........................
47Figure 54. Power supply current of 180 GB models ...................................
47Figure 53. Input voltage ...........................................................
Deskstar 180GXP hard disk drive specifications
xii
199Figure 163. SMART Log Directory .................................................
198Figure 162. Individual Threshold Data Structure .....................................
198Figure 161. Device Attribute Thresholds Data Structure ..............................
195Figure 160. Individual Attribute Data Structure ......................................
194Figure 159. Device Attributes Data Structure .......................................
192Figure 158. Log sector addresses .................................................
189Figure 157. S.M.A.R.T. Function Set Command (B0h) ...............................
188Figure 156. Sleep Command (E6h/99h) ............................................
187Figure 155. Set Multiple Command (C6h) ..........................................
185Figure 154. Set Max Address Ext Command (37h) ..................................
184Figure 153. Set Max Freeze Lock (F9h) ............................................
183Figure 152. Set Max Unlock (F9h) .................................................
182Figure 151. Set Max Lock ........................................................
181Figure 150. Set Max Set Password data contents ...................................
181Figure 149. Set Max Set Password ................................................
179Figure 148. Set Max Address (F9h) ...............................................
175Figure 147. Set Features Command (EFh) .........................................
174Figure 146. Service Command (A2h) ..............................................
173Figure 145. Seek Command (7xh) .................................................
172Figure 144. Security Unlock Information ............................................
171Figure 143. Security Unlock Command (F2h) .......................................
170Figure 142. Security Set Password Information .....................................
169Figure 141. Security Set Password Command (F1h) .................................
168Figure 140. Security Freeze Lock Command (F5h) ..................................
166Figure 139. Erase Unit Information ................................................
166Figure 138. Security Erase Unit Command (F4h) ....................................
165Figure 137. Security Erase Prepare Command (F3h) ................................
164Figure 136. Password Information for Security Disable Password command ............
164Figure 135. Security Disable Password Command (F6h) .............................
163Figure 134. Recalibrate Command (1xh) ...........................................
161Figure 133. Read Verify Sectors(s) Ext Command (42h) ..............................
159Figure 132. Read Verify Sectors(s) Command (40h/41h) .............................
157Figure 131. Read Sector(s) Ext Command (24h) ....................................
155Figure 130. Read Sector(s) Command (20h/21h) ....................................
154Figure 129. Read Native Max Address Ext (F8h) ....................................
153Figure 128. Read Native Max Address (F8h) .......................................
151Figure 127. Read Multiple Ext (29h) ...............................................
149Figure 126. Read Multiple Command (C4h) ........................................
147Figure 125. Read Long Command (22h/23h) .......................................
146Figure 124. Extended Self-test log descriptor entry ..................................
145Figure 123. Extended Self-test log data structure ...................................
144Figure 122. Error data structure ..................................................
143Figure 121. Command data structure .............................................
143Figure 120. Extended Error log data structure ......................................
142Figure 119. Extended Comprehensive SMART Error Log .............................
141Figure 118. General Purpose Log Directory ........................................
141Figure 117. Log Address Definition ................................................
140Figure 116. Read Log Ext Command (2Fh) .........................................
138Figure 115. Read DMA Queued Ext Command (26h) ................................
136Figure 114. Read DMA Queued Command (C7h) ...................................
134Figure 113. Read DMA Ext Command (25h) ........................................
132Figure 112. Read DMA Command (C8h/C9h) .......................................
131Figure 111. Read Buffer Command (E4h) ..........................................
130Figure 110. NOP Command (00h) .................................................
129Figure 109. Initialize Device Parameters Command (91h) ............................
128Figure 108. Idle Immediate Command (E1h/95h) ....................................
Deskstar 180GXP hard disk drive specifications
xiii
229Figure 1. Time-out values ........................................................
227Figure 182. Write Sector(s) Ext Command (34h) ....................................
225Figure 181. Write Sector(s) Command (30h/31h) ....................................
223Figure 180. Write Multiple Command (C5h) .........................................
221Figure 179. Write Multiple Command (C5h) .........................................
219Figure 178. Write Long Command (32h/33h) .......................................
217Figure 177. Write Log Ext Command (3Fh) .........................................
215Figure 176. Write DMA Queued Command (36h) ....................................
213Figure 175. Write DMA Queued Command (CCh) ...................................
211Figure 174. Write DMA Command (CAh/CBh) ......................................
209Figure 173. Write DMA Command (CAh/CBh) ......................................
208Figure 172. Write Buffer Command (E8h) ..........................................
207Figure 171. Standby Immediate Command (E0h/94h) ................................
205Figure 170. Standby Command (E2h/96h) ..........................................
204Figure 169. S.M.A.R.T. Error Codes ...............................................
203Figure 168. Self-test log data structure .............................................
202Figure 167. Error data structure ...................................................
201Figure 166. Command data structure ..............................................
201Figure 165. Error log data structure ................................................
200Figure 164. SMART summary error log sector ......................................
Deskstar 180GXP hard disk drive specifications
xiv
1.0 General
This document describes the specifications of the Deskstar 180GXP, an IBM 3.5-inch 7200-rpm
ATA interface hard disk drive with the following model numbers:
y IC35L030AVV207- 0 (30.7 GB, 2-MB buffer)
y IC35L060AVV207- 0 (41.2 GB and 60.4 GB, 2-MB buffer)
y IC35L090AVV207- 0 (82.3 GB, 2-MB buffer)
y IC35L090AVV207- 1 (82.3 GB, 8-MB buffer)
y IC35L120AVV207- 0 (123.5 GB, 2-MB buffer)
y IC35L120AVV207- 1 (123.5 GB, 8-MB buffer)
y IC35L180AVV207- 1 (185.2 GB, 8-MB buffer)
Part 1 defines the functional specification. Part 2 defines the interface specification.
The specifications in this document are subject to change without notice.
1.1 Glossary
ESD Electrostatic Discharge
Kbpi 1,000 bits per inch
Ktpi 1,000 tracks per inch
Mbps 1,000,000 bits per second
GB 1,000,000,000 bytes
MB 1,000,000 bytes
KB 1,000 bytes unless otherwise specified
32KB 32 x 1024 bytes
64KB 64 x 1024 bytes
S.M.A.R.T. Self-Monitoring Analysis and Reporting Technology
DFT Drive Fitness Test
ADM Automatic Drive Maintenance
1.2 General caution
The drive can be damaged by shock or ESD (Electrostatic Discharge). Any damage sustained by the
drive after removal from the shipping package and opening the ESD protective bag is the responsibility of
the user.
1.3 References
y Information Technology-AT Attachment with Packet Interface-6
Deskstar 180GXP hard disk drive specifications
1
This page intentionally left blank.
2.0 General features
y Data capacities of 30 GB - 180 GB
y Spindle speeds of 7200 RPM
y Fluid Dynamic Bearing motor
y Enhanced IDE interface
y Sector format of 512 bytes/sector
y Closed-loop actuator servo
y Load/Unload mechanism
y Automatic Actuator lock
y Interleave factor 1:1
y Seek time of 8.8 ms (30-GB, 40-GB, and 60-GB models), 8.5 ms (all other models) in Read
Operation
y Seek time of 8.5 ms (30-GB, 40-GB, and 60-GB models), 8.2 ms (all other models) typical
without Command Overhead)
y Sector Buffer size of 2048 KB and 8192 KB (Upper 226.5 KB is used for firmware)
y Ring buffer implementation
y Write Cache
y Queued feature support
y Advanced ECC On The Fly (EOF)
y Automatic Error Recovery procedures for read and write commands
y Self Diagnostics on Power on and resident diagnostics
y PIO Data Transfer Mode 4 (16.6 MB/s)
y DMA Data Transfer
- Multiword mode Mode 2 (16.6 MB/s)
- Ultra DMA Mode 5 (100 MB/s)
y CHS and LBA mode
y Power saving modes/Low RPM idle mode (APM)
y S.M.A.R.T. (Self Monitoring and Analysis Reporting Technology)
y Support security feature
y Quiet Seek mode (AAM)
y 48-bit addressing feature
Deskstar 180GXP hard disk drive specifications
3
This page intentionally left blank.
Part 1. Functional specification
Deskstar 180GXP hard disk drive specifications
5
This page intentionally left blank.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247

Hitachi IC35L180AVV207 Datasheet

Category
Internal hard drives
Type
Datasheet

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI