StarTech.com CF2USAT18E Installation guide

Brand
StarTech.com
Model
CF2USAT18E
Category
HDD/SSD enclosures
Type
Installation guide

StarTech.com CF2USAT18E is a 1.8” Micro SATA to Compact Flash Solid State Drive Enclosure Adapter. It allows you to use a Compact Flash card as a SATA hard drive. The enclosure supports both 3.3V CF type I and II cards, including SLC and MLC types. It is compatible with Microsoft Windows® 2000/XP/Vista, Mac OS® 10.x, and Linux®. The enclosure is easy to install, with no drivers required. Simply insert your Compact Flash card into the enclosure, and connect it to your computer using a SATA cable. The enclosure is powered by the SATA bus, so no external power supply is required.

StarTech.com CF2USAT18E is a 1.8” Micro SATA to Compact Flash Solid State Drive Enclosure Adapter. It allows you to use a Compact Flash card as a SATA hard drive. The enclosure supports both 3.3V CF type I and II cards, including SLC and MLC types. It is compatible with Microsoft Windows® 2000/XP/Vista, Mac OS® 10.x, and Linux®. The enclosure is easy to install, with no drivers required. Simply insert your Compact Flash card into the enclosure, and connect it to your computer using a SATA cable. The enclosure is powered by the SATA bus, so no external power supply is required.

Warranty Information
This product is backed by a one year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising
from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct
or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of
the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws
apply, the limitations or exclusions contained in this statement may not apply to you.
CF2USAT18E
1.8” Micro SATA to Compact Flash Solid
State Drive Enclosure Adapter
Installation Guide
Packaging Contents
1 x CF2USAT18E enclosure•
1 x Mini Screwdrivers•
1 x Installation Guide•
System Requirements
3.3V Compact Flash card•
Microsoft Windows•
®
2000/XP/Vista,
Mac OS
®
10.x, Linux
®
Installation
Hardware Installation
Remove the 4 small screws on the underside of the enclosure, and remove the cover plate.1.
Remove the circuit board and insert the Compact Flash card into the CF card slot.2.
Reinstall the circuit board into the enclosure.3.
Place the metal cover back on and replace the 4 screws.4.
Driver Installation
No drivers should need to be installed for this enclosure, as the enclosure appears as a
standard SATA hard drive.
Specications
Bus Interface
SATA rev 2.x
Connectors
Micro SATA connector
(7+9 pin)
Power Consumption
5V / 150mA
CF Compatibility
3.3V CF type I and II
(SLC/MLC)*
Supported Operating
Systems
Windows
®
2000/XP/
Vista, Mac OS
®
10.x,
Linux
®
Note: If an MLC type card is used, write speeds will be less than *
  • Page 1 1

StarTech.com CF2USAT18E Installation guide

Brand
StarTech.com
Model
CF2USAT18E
Category
HDD/SSD enclosures
Type
Installation guide

StarTech.com CF2USAT18E is a 1.8” Micro SATA to Compact Flash Solid State Drive Enclosure Adapter. It allows you to use a Compact Flash card as a SATA hard drive. The enclosure supports both 3.3V CF type I and II cards, including SLC and MLC types. It is compatible with Microsoft Windows® 2000/XP/Vista, Mac OS® 10.x, and Linux®. The enclosure is easy to install, with no drivers required. Simply insert your Compact Flash card into the enclosure, and connect it to your computer using a SATA cable. The enclosure is powered by the SATA bus, so no external power supply is required.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers