Cisco Systems SFS 7000P User manual

Brand: Cisco Systems

Model: SFS 7000P

Type: User manual

This manual is also suitable for

Cisco SFS 7000P

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 526-4100

Cisco SFS 7000P Hardware

Installation Guide

May 2006

Customer Order Number:

Text Part Number: OL-9167-01 Rev. A0

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT

NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT

ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR

THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION

PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO

LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate

radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television

reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in

part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation.

However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class

A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct

any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco

equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by

using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television

or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE

PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED

OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL

DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR

INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We

Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA,

CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems

Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive,

GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace,

MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX,

ScriptShare, SlideCast, SMARTnet, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems,

Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply

a partnership relationship between Cisco and any other company. (0601R)

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

CONTENTS

Audience ix

Organization x

Conventions x

Statement 1071—Warning Definition xii

Related Documentation xvi

Obtaining Documentation xvii

Cisco.com xvii

Product Documentation DVD xvii

Ordering Documentation xviii

Documentation Feedback xviii

Cisco Product Security Overview xviii

Reporting Security Problems in Cisco Products xix

Obtaining Technical Assistance xx

Cisco Technical Support & Documentation Website xx

Submitting a Service Request xxi

Definitions of Service Request Severity xxi

Obtaining Additional Publications and Information xxii

CHAPTER

1 Product Overview 1-1

Switch Description 1-1

Connectors 1-2

Switch Components 1-2

LEDs 1-2

Power Supplies and Fan Units 1-2

Contents

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Power Supply Bay 1-2

Power Supplies and Fan Trays 1-3

System Features 1-3

InfiniBand Connectivity 1-3

Scalability 1-3

High Availability 1-3

Hardware 1-4

Ports 1-4

Fabric 1-4

Nonblocking Architecture 1-5

Administrative Features 1-5

Real-Time Clock 1-5

Latency 1-5

Nonvolatile Memory 1-5

Vital Product Data Storage 1-5

Diagnostics 1-6

CHAPTER

2 Installing the Cisco SFS 7000P Switch 2-1

Safety 2-2

Preparing for Installation 2-3

Configuring Basic Connectivity 2-3

Attaching a Serial Console Cable to a PC or Terminal 2-3

Powering Up the Chassis 2-4

Rack-Mounting the Cisco SFS 7000P Switch 2-5

Requirements 2-5

Rack-Mounting the Switch 2-6

Installing the Switch with One Person 2-6

Installing the Switch with Two People 2-11

Connecting Network Devices 2-11

vii

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Contents

Connecting InfiniBand Devices 2-12

Connecting Management Devices 2-15

Managing the System 2-15

CHAPTER

3 Installing Field Replaceable Units 3-1

Power and Fan Modules 3-1

Locating the Power Supply or Fan Unit 3-1

Failed Power Supplies or Fan Units 3-2

Installing a Power Supply or Fan Unit 3-2

Removing Power Supplies and Fan Units 3-5

CHAPTER

4 Managing the Cisco SFS 7000P Switch 4-1

LEDs 4-1

Chassis Status LEDs 4-1

InfiniBand Port LEDs 4-2

Power Supply and Fan LEDs 4-3

Managing the System with Element Manager 4-3

Using the Summary Tab 4-4

Using the Power Supplies Tab 4-5

Using the Fans Tab 4-5

Using the Sensors Tab 4-6

Displaying System Information 4-6

Displaying Power Supply Information 4-7

Displaying Fan Information 4-7

Displaying Sensor Information 4-8

CHAPTER

5 Hardware Diagnostic Tests 5-1

About Diagnostic Tests 5-1

LED Tests 5-1

Contents

viii

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Self-Tests 5-2

Running Card Tests 5-2

Running a Card Self-Test 5-2

Running Chassis Tests 5-3

Running a Chassis Standard Test 5-3

Running Fan Tests 5-5

Running a Self-Test on a Fan 5-5

Running Power Supply Tests 5-7

Running a LED Test on the Power Supply 5-7

Running a Self-Test on a Power Supply 5-7

Displaying Hardware Errors 5-9

APPENDIX

A Specifications and Compliance Certifications A-1

Chassis and Management Interface A-1

Electrical Specifications A-2

NDEX

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Preface

This preface describes who should read the Cisco SFS 7000P Hardware

Installation Guide, how it is organized, and its document conventions.

Audience

Only trained and qualified service personnel (as defined in IEC 60950 and

AS/NZS3260) should install, replace, or service the equipment described in this

publication.

Preface

Organization

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Organization

This publication is organized as follows:

Conventions

This publication uses the following conventions:

Chapter Title Description

Chapter 1 Product Overview Provides an overview of the Cisco SFS 7000P switch

features.

Chapter 2 Installing the Cisco SFS

7000P Switch

Describes how to install the switch in a rack.

Chapter 3 Installing Field

Replaceable Units

Describes how to install and remove field-replaceable

units (FRUs) on the switch.

Chapter 4 Managing the Cisco SFS

7000P Switch

Provides upgrade procedures for switch components.

Chapter 5 Hardware Diagnostic

Tests

Describes how to monitor switch performance.

Appendix A Specifications and

Compliance

Certifications

Provides specifications and compliance information.

Convention Description

boldface font Commands, command options, and keywords are in boldface.

italic font Arguments for which you supply values are in italics.

[ ] Elements in square brackets are optional.

{ x | y | z } Alternative keywords are grouped in braces and separated by vertical bars.

[ x | y | z ] Optional alternative keywords are grouped in brackets and separated by

vertical bars.

string A nonquoted set of characters. Do not use quotation marks around the string

or the string will include the quotation marks.

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Preface

Conventions

Notes use the following conventions:

Note Means reader take note. Notes contain helpful suggestions or references to

material not covered in the publication.

Cautions use the following conventions:

Caution Means reader be careful. In this situation, you might do something that could

result in equipment damage or loss of data.

screen font Terminal sessions and information the system displays are in screen font.

boldface screen font Information you must enter is in boldface screen font.

italic screen font Arguments for which you supply values are in italic screen font.

^ The symbol ^ represents the key labeled Control. For example, the key

combination ^D in a screen display means hold down the Control key while

you press the D key.

< > Nonprinting characters, such as passwords, are in angle brackets.

Convention Description

Preface

Conventions

xii

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Warnings use the following conventions:

Statement 1071—Warning Definition

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause

bodily injury. Before you work on any equipment, be aware of the hazards

involved with electrical circuitry and be familiar with standard practices for

preventing accidents. Use the statement number provided at the end of each

warning to locate its translation in the translated safety warnings that

accompanied this device.

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat

werken, dient u zich bewust te zijn van de bij elektrische schakelingen

betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken

om ongelukken te voorkomen. Gebruik het nummer van de verklaring

onderaan de waarschuwing als u een vertaling van de waarschuwing die bij

het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia

vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien

käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin

ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta

varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

xiii

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Preface

Conventions

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant

de travailler sur un équipement, soyez conscient des dangers liés aux circuits

électriques et familiarisez-vous avec les procédures couramment utilisées

pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui

accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la

fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die

zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit

den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur

Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung

angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den

übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät

ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe

causare infortuni alle persone. Prima di intervenire su qualsiasi

apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti

elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per

individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Preface

Conventions

xiv

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade

på person. Før du begynner å arbeide med noe av utstyret, må du være

oppmerksom på farene forbundet med elektriske kretser, og kjenne til

standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver

advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som

fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá

ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer

equipamento, tenha conhecimento dos perigos envolvidos no manuseio de

circuitos elétricos e familiarize-se com as práticas habituais de prevenção de

acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham

este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física.

Antes de manipular cualquier equipo, considere los riesgos de la corriente

eléctrica y familiarícese con los procedimientos estándar de prevención de

accidentes. Al final de cada advertencia encontrará el número que le ayudará

a encontrar el texto traducido en el apartado de traducciones que acompaña

a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Preface

Conventions

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan

leda till personskada. Innan du utför arbete på någon utrustning måste du vara

medveten om farorna med elkretsar och känna till vanliga förfaranden för att

förebygga olyckor. Använd det nummer som finns i slutet av varje varning för

att hitta dess översättning i de översatta säkerhetsvarningar som medföljer

denna anordning.

SPARA DESSA ANVISNINGAR

Preface

Related Documentation

For instructions on installing and configuring Cisco SFS 7000P and 7008P

switches, refer to these publications:

• Cisco SFS 7008P Hardware Installation Guide

• Cisco SFS 7000P Switch Installation and Configuration Note

• Cisco SFS 7008P Switch Installation and Configuration Note

• Cisco SFS 7000 Series Product Family Chassis Manager User Guide

• Cisco SFS 7000 Series Product Family Element Manager User Guide

• Regulatory Compliance and Safety Information for the Cisco SFS 7000 Series

Switches

xvii

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Preface

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco

also provides several ways to obtain technical assistance and other technical

resources. These sections explain how to obtain technical information from Cisco

Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/techsupport

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Product Documentation DVD

The Product Documentation DVD is a comprehensive library of technical product

documentation on a portable medium. The DVD enables you to access multiple

versions of installation, configuration, and command guides for Cisco hardware

and software products. With the DVD, you have access to the same HTML

documentation that is found on the Cisco website without being connected to the

Internet. Certain products also have .PDF versions of the documentation

available.

The Product Documentation DVD is available as a single unit or as a subscription.

Registered Cisco.com users (Cisco direct customers) can order a Product

Documentation DVD (product number DOC-DOCDVD= or

DOC-DOCDVD=SUB) from Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Preface

Documentation Feedback

xviii

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Ordering Documentation

Registered Cisco.com users may order Cisco documentation at the Product

Documentation Store in the Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Nonregistered Cisco.com users can order technical documentation from 8:00 a.m.

to 5:00 p.m. (0800 to 1700) PDT by calling 1 866 463-3487 in the United States

and Canada, or elsewhere by calling 011 408 519-5055. You can also order

documentation by e-mail at tech-doc-store-mkpl@external.cisco.com or by fax at

1 408 519-5001 in the United States and Canada, or elsewhere at 011 408

519-5001.

Documentation Feedback

You can rate and provide feedback about Cisco technical documents by

completing the online feedback form that appears with the technical documents

on Cisco.com.

You can submit comments about Cisco documentation by using the response card

(if present) behind the front cover of your document or by writing to the following

address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.ht

xix

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

Preface

Cisco Product Security Overview

From this site, you will find information about how to:

• Report security vulnerabilities in Cisco products.

• Obtain assistance with security incidents that involve Cisco products.

• Register to receive security information from Cisco.

A current list of security advisories, security notices, and security responses for

Cisco products is available at this URL:

http://www.cisco.com/go/psirt

To see security advisories, security notices, and security responses as they are

updated in real time, you can subscribe to the Product Security Incident Response

Team Really Simple Syndication (PSIRT RSS) feed. Information about how to

subscribe to the PSIRT RSS feed is found at this URL:

http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally

before we release them, and we strive to correct all vulnerabilities quickly. If you

think that you have identified a vulnerability in a Cisco product, contact PSIRT:

• For Emergencies only—[email protected]

An emergency is either a condition in which a system is under active attack

or a condition for which a severe and urgent security vulnerability should be

reported. All other conditions are considered nonemergencies.

• For Nonemergencies— [email protected]

In an emergency, you can also reach PSIRT by telephone:

• 1 877 228-7302

• 1 408 525-6532

Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for

example, GnuPG) to encrypt any sensitive information that you send to Cisco.

PSIRT can work with information that has been encrypted with PGP versions 2.x

through 9.x.

Never use a revoked or an expired encryption key. The correct public key to use

Preface

Obtaining Technical Assistance

Cisco SFS 7000P Hardware Installation Guide

OL-9167-01 Rev. A0

in your correspondence with PSIRT is the one linked in the Contact Summary

section of the Security Vulnerability Policy page at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.ht

The link on this page has the current PGP key ID in use.

If you do not have or use PGP, contact PSIRT at the aforementioned e-mail

addresses or phone numbers before sending any sensitive material to find other

means of encrypting the data.

Obtaining Technical Assistance

Cisco Technical Support provides 24-hour-a-day award-winning technical

assistance. The Cisco Technical Support & Documentation website on Cisco.com

features extensive online support resources. In addition, if you have a valid Cisco

service contract, Cisco Technical Assistance Center (TAC) engineers provide

telephone support. If you do not have a valid Cisco service contract, contact your

reseller.

Cisco Technical Support & Documentation Website

The Cisco Technical Support & Documentation website provides online

documents and tools for troubleshooting and resolving technical issues with Cisco

products and technologies. The website is available 24 hours a day, at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support & Documentation website

requires a Cisco.com user ID and password. If you have a valid service contract

but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Note Use the Cisco Product Identification (CPI) tool to locate your product serial

number before submitting a web or phone request for service. You can access the

CPI tool from the Cisco Technical Support & Documentation website by clicking

Page is loading ...

Cisco Systems SFS 7000P User manual

Brand: Cisco Systems

Model: SFS 7000P

Type: User manual

This manual is also suitable for

Cisco SFS 7000P

Download PDF

report

Cisco Systems SFS 7000P User manual

This manual is also suitable for

Cisco Systems SFS 7000P User manual

Related papers

Other documents