Cisco AS5350XM Installation guide

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 526-4100

Cisco AS5350XM and

Cisco AS5400XM Universal Gateways

Card Installation Guide

Customer Order Number: DOC-7817406=

Text Part Number: 78-17406-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not

installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to

comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital

devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television

communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its

peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits

controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and

iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified

Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast,

EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream,

Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packe t , PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare,

SlideCast, SMARTnet, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States

and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0601R)

iii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

CONTENTS

Preface vii

Document Organization vii

Document Conventions viii

Obtaining Documentation xiv

Cisco.com xiv

Product Documentation DVD xiv

Ordering Documentation xiv

Documentation Feedback xiv

Cisco Product Security Overview xv

Reporting Security Problems in Cisco Products xv

Obtaining Technical Assistance xvi

Cisco Technical Support & Documentation Website xvi

Submitting a Service Request xvii

Definitions of Service Request Severity xvii

Obtaining Additional Publications and Information xviii

CHAPTER

1 Safety Warnings, Recommendations, and Tools Required 1-1

General Safety 1-1

Maintaining Safety with Electricity 1-2

Preventing Electrostatic Discharge 1-3

Required Tools and Equipment 1-3

Where to Go Next 1-4

CHAPTER

2 Feature Card and Carrier Card Guidelines 2-1

Overview 2-1

Online Insertion and Removal of Feature Cards 2-2

Removing and Installing Populated Carrier Cards 2-2

Removing a Populated Carrier Card 2-3

Installing a Populated Carrier Card 2-5

Getting Help 2-7

Where to Go Next 2-7

Contents

iv

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

CHAPTER

3 T1 and E1 Feature Cards 3-1

Overview 3-1

Online Installation and Removal of the T1 or E1 Feature Card 3-2

Removing the T1 or E1 Feature Card 3-3

Installing the T1 or E1 Feature Card 3-9

Configuring Input Impedance for the E1 Feature Card 3-11

Configuration 3-11

Verification 3-12

Getting Help 3-12

Where to Go Next 3-12

CHAPTER

4 Channelized T3 Feature Card 4-1

Overview 4-1

Online Insertion and Removal of the CT3 Feature Card 4-2

Removing the CT3 Feature Card 4-2

Installing the CT3 Feature Card 4-5

Getting Help 4-7

Where to Go Next 4-7

CHAPTER

5 Universal Port and Dial-Only Feature Cards 5-1

Overview 5-1

Restrictions for the Universal Port and Dial-Only Feature Cards 5-2

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card 5-3

Removing the Universal Port or Dial-Only Feature Card 5-3

Installing the Universal Port or Dial-Only Feature Card 5-8

System Processing Engine Firmware 5-10

Getting Help 5-10

Where to Go Next 5-10

CHAPTER

6 Voice Feature Card 6-1

Overview 6-1

Restrictions for the Voice Feature Card 6-2

Online Insertion and Removal of the Voice Feature Card 6-3

Removing the Voice Feature Card 6-3

Installing the Voice Feature Card 6-7

Replacing PVDM2 Modules in the Voice Feature Card 6-8

Orienting the PVDM2 Module During Installation 6-9

Contents

v

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Removing PVDM2 Modules From the Voice Feature Card 6-9

Installing PVDM2 Modules in the Voice Feature Card 6-10

Digital Signal Processor Firmware 6-11

Getting Help 6-11

Where to Go Next 6-11

CHAPTER

7 Troubleshooting 7-1

LEDs 7-1

Mixing WAN Feature Cards 7-5

Mixing Universal Port and Dial-Only Feature Cards 7-6

Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards 7-6

Monitoring the Chassis Environment 7-7

Displaying Environment Status 7-8

Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards 7-10

Using Drop and Insert Mode on the CT3 Feature Card 7-10

Troubleshooting Network Interfaces 7-11

Getting Help 7-11

APPENDIX

A Cabling Specifications A-1

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts A-1

8-Port T1 or E1 Feature Card Cable and Port Pinouts A-6

Attaching the 8-Port T1 or E1 Feature Card Interface Cable to a Bracket (Optional) A-8

CT3 Feature Card Cable and Port Pinouts A-12

Bantam Jack Port Pinouts A-13

I

NDEX

Contents

vi

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

vii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

This preface describes the objectives and organization of this document and explains how to find

additional information on related products and services. This preface contains the following sections:

• Document Organization, page vii

• Document Conventions, page viii

• Obtaining Documentation, page xiv

• Documentation Feedback, page xiv

• Cisco Product Security Overview, page xv

• Obtaining Technical Assistance, page xvi

• Obtaining Additional Publications and Information, page xviii

Document Organization

This publication is designed for people who have some experience installing networking equipment such

as routers, hubs, servers, and switches. The person who installs the server should be familiar with

electronic circuitry and wiring practices and have experience as an electronic or electromechanical

technician.

Table 1 describes the contents of each chapter in this document.

Table 1 Document Organization

Chapter Title Description

Chapter 1 Safety Warnings,

Recommendations, and

Tools Required

Describes the safety warnings, recommendations, and the

tools required to install dial feature cards in the chassis.

Chapter 2 Feature Card and Carrier

Card Guidelines

Describes the tasks you must perform to remove and

install carrier cards.

Chapter 3 T1 and E1 Feature Cards Describes online insertion and removal (OIR) tasks that

you must perform on the T1 or E1 feature card.

Chapter 4 Channelized T3 Feature

Card

Describes OIR tasks that you must perform on the

channelized T3 (CT3) feature card.

Chapter 5 Universal Port and

Dial-Only Feature Cards

Describes OIR tasks that you must perform on the

universal port and dial-only feature cards.

viii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

This publication uses the following conventions to convey instructions and information.

Note Means reader take note. Notes contain helpful suggestions or references to additional information and

material.

Timesaver This symbol means the described action saves time. You can save time by performing the action

described in the paragraph.

Caution This symbol means reader be careful. In this situation, you might do something that could result in

equipment damage or loss of data.

Tip This symbol means the following information will help you solve a problem. The tips information might

not be troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Chapter 6 Voice Feature Card Describes OIR tasks that you must perform on the voice

feature card.

Chapter 7 Troubleshooting Describes how to troubleshoot by using LEDs, bantam

jacks, and environmental monitoring.

Appendix A Cabling Specifications Describes cabling and pinout information for the dial

feature cards.

Table 1 Document Organization (continued)

Chapter Title Description

Convention Description

boldface font Commands and keywords.

italic font Variables for which you supply values.

[ ] Keywords or arguments that appear within square brackets are optional.

{x | y | z} A choice of required keywords appears in braces separated by vertical bars.

You must select one.

screen font Examples of information displayed on the screen.

boldface screen

font

Examples of information you must enter.

< > Nonprinting characters, for example passwords, appear in angle brackets in

contexts where italic font is not available.

[ ] Default responses to system prompts appear in square brackets.

ix

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij

elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard

praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de

waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt

raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu

onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien

lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez

conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures

couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen

führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen

und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

x

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle

persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli

relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le

traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du

begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med

elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten

av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne

enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de

lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos

perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de

prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular

cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los

procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el

número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña

a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och

känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av

varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna

anordning.

SPARA DESSA ANVISNINGAR

xi

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

xii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões

corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os

circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o

número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de

segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for

legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de

involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til

undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de

oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

xiii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

xiv

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several

ways to obtain technical assistance and other technical resources. These sections explain how to obtain

technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/techsupport

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Product Documentation DVD

The Product Documentation DVD is a comprehensive library of technical product documentation on a

portable medium. The DVD enables you to access multiple versions of installation, configuration, and

command guides for Cisco hardware and software products. With the DVD, you have access to the same

HTML documentation that is found on the Cisco website without being connected to the Internet.

Certain products also have .PDF versions of the documentation available.

The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com

users (Cisco direct customers) can order a Product Documentation DVD (product number

DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Ordering Documentation

Registered Cisco.com users may order Cisco documentation at the Product Documentation Store in the

Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m.

(0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by

calling 011 408 519-5055. You can also order documentation by e-mail at

tech-doc-store-mkpl@external.cisco.com or by fax at 1 408 519-5001 in the United States and Canada,

or elsewhere at 011 408 519-5001.

Documentation Feedback

You can rate and provide feedback about Cisco technical documents by completing the online feedback

form that appears with the technical documents on Cisco.com.

xv

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Cisco Product Security Overview

You can submit comments about Cisco documentation by using the response card (if present) behind the

front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

From this site, you will find information about how to:

• Report security vulnerabilities in Cisco products.

• Obtain assistance with security incidents that involve Cisco products.

• Register to receive security information from Cisco.

A current list of security advisories, security notices, and security responses for Cisco products is

available at this URL:

http://www.cisco.com/go/psirt

To see security advisories, security notices, and security responses as they are updated in real time, you

can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS)

feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL:

http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally before we release them,

and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability

in a Cisco product, contact PSIRT:

• For Emergencies only— s[email protected]

An emergency is either a condition in which a system is under active attack or a condition for which

a severe and urgent security vulnerability should be reported. All other conditions are considered

nonemergencies.

• For Nonemergencies—[email protected]

In an emergency, you can also reach PSIRT by telephone:

• 1 877 228-7302

• 1 408 525-6532

xvi

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Technical Assistance

Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for example, GnuPG) to

encrypt any sensitive information that you send to Cisco. PSIRT can work with information that has been

encrypted with PGP versions 2.x through 9.x.

Never use a revoked or an expired encryption key. The correct public key to use in your correspondence

with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page

at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

The link on this page has the current PGP key ID in use.

If you do not have or use PGP, contact PSIRT at the aforementioned e-mail addresses or phone numbers

before sending any sensitive material to find other means of encrypting the data.

Obtaining Technical Assistance

Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco

Technical Support & Documentation website on Cisco.com features extensive online support resources.

In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC)

engineers provide telephone support. If you do not have a valid Cisco service contract, contact your

reseller.

Cisco Technical Support & Documentation Website

The Cisco Technical Support & Documentation website provides online documents and tools for

troubleshooting and resolving technical issues with Cisco products and technologies. The website is

available 24 hours a day, at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user

ID and password. If you have a valid service contract but do not have a user ID or password, you can

register at this URL:

http://tools.cisco.com/RPF/register/register.do

Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting

a web or phone request for service. You can access the CPI tool from the Cisco Technical Support &

Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose

Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco

Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by

product ID or model name; by tree view; or for certain products, by copying and pasting show command

output. Search results show an illustration of your product with the serial number label location

highlighted. Locate the serial number label on your product and record the information before placing a

service call.

xvii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Technical Assistance

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3

and S4 service requests are those in which your network is minimally impaired or for which you require

product information.) After you describe your situation, the TAC Service Request Tool provides

recommended solutions. If your issue is not resolved using the recommended resources, your service

request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone.

(S1 or S2 service requests are those in which your production network is down or severely degraded.)

Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business

operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)

EMEA: +32 2 704 55 55

USA: 1 800 553-2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity

definitions.

Severity 1 (S1)—An existing network is down, or there is a critical impact to your business operations.

You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your

business operations are negatively affected by inadequate performance of Cisco products. You and Cisco

will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of the network is impaired, while most business operations

remain functional. You and Cisco will commit resources during normal business hours to restore service

to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or

configuration. There is little or no effect on your business operations.

xviii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online

and printed sources.

• The Cisco Product Quick Reference Guide is a handy, compact reference tool that includes brief

product overviews, key features, sample part numbers, and abbreviated technical specifications for

many Cisco products that are sold through channel partners. It is updated twice a year and includes

the latest Cisco offerings. To order and find out more about the Cisco Product Quick Reference

Guide, go to this URL:

http://www.cisco.com/go/guide

• Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo

merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

• Cisco Press publishes a wide range of general networking, training and certification titles. Both new

and experienced users will benefit from these publications. For current Cisco Press titles and other

information, go to Cisco Press at this URL:

http://www.ciscopress.com

• Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and

networking investments. Each quarter, Packet delivers coverage of the latest industry trends,

technology breakthroughs, and Cisco products and solutions, as well as network deployment and

troubleshooting tips, configuration examples, customer case studies, certification and training

information, and links to scores of in-depth online resources. You can access Packet magazine at

this URL:

http://www.cisco.com/packet

• iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies

learn how they can use technology to increase revenue, streamline their business, and expand

services. The publication identifies the challenges facing these companies and the technologies to

help solve them, using real-world case studies and business strategies to help readers make sound

technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

or view the digital edition at this URL:

http://ciscoiq.texterity.com/ciscoiq/sample/

• Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering

professionals involved in designing, developing, and operating public and private internets and

intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

• Networking products offered by Cisco Systems, as well as customer support services, can be

obtained at this URL:

http://www.cisco.com/en/US/products/index.html

xix

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Additional Publications and Information

• Networking Professionals Connection is an interactive website for networking professionals to share

questions, suggestions, and information about networking products and technologies with Cisco

experts and other networking professionals. Join a discussion at this URL:

http://www.cisco.com/discuss/networking

• World-class networking training is available from Cisco. You can view current offerings at

this URL:

http://www.cisco.com/en/US/learning/index.html

xx

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Additional Publications and Information

Page is loading ...

Cisco AS5350XM Installation guide

This manual is also suitable for

Cisco AS5350XM Installation guide

Related papers

Other documents