ASO Safety Solutions SENTIR edge 15-10 TT Assembly Instructions

Type
Assembly Instructions
Continued over leaf
Assembly Instructions
Safety-contact-edges may only be manufactured and installed by authorised persons.
1. Cutting the safety-contact-edge
The contact edge is to be cut to correct length (cut measure) using the approved LOWE cutting tool ONLY.
It is to be noted that the cut ends of section are right-angled and smooth. The measurement should be
27mm shorter than the final dimension of the finished contact edge (hight of end caps). Do not attempt
to cut the profile with craft knives or any other non-approved tool, to do so will invalidate any warranty.
2. Preparing the end caps
Cut out the appropriate cable entry of the end cap at the marked place, by which the cable is implemented,
with a side cutter.
The arrangement of the individual components depends on the respective gate construction and on
structural conditions, which must be considered.
3. Preparing the end caps
Insert the wiring plug (KS2L) or resistor plug (KS2W) in to the
switching chamber half-way ensuring that the pins on the plug
penetrate directly in to the copper braid within the top and
bottom parts of the switching chamber as illustrated.
4. Testing
Measure the plugged contact edge with a commercial resistance measuring instrument. For
in-operated condition the resistance has to be 8,2 ± 500 Ω and in operated condition the
resistance may not exceed 1 kΩ.
NOTE: If the resistor value is incorrect, the KS2 plugs have to be removed and pressed in again
& re-measured before proceeding to the glue application stage.
5. Gluing the KS2 plugs
Coat the surfaces of the KS2 plug and the switching chamber which will be stuck together, with the ASO CA-Primer (brush included in bottle). Then coat the
KS2 plug & switching chamber face all-around generously with ASO glue Contact VA 250 black. Immediately press the KS2 plug fully it into the switching
chamber (using either optional assembly tool or thumb) and hold in position for approximately 30 seconds. After releasing the plug there should be no visible
sign of any gaps between the KS2 plug and wall of the switching chamber.
These steps are to be repeated for the other end of the safety edge.
! PLEASE NOTE !
The ambient temperature during gluing should be between 10° and 30°C and the relative
humidity between 40% and 70%. It is not recommended to attempt assembly in atmospheric
conditions outside of these values, any attempt to do so may invalidate the product warranty.
The prole should be stored in dry conditions and checked thoroughly before the cutting &
assembly process for the prescense of any moisture or damage.
c
n
u
t
d
im
e
n
sio
d
i
m
e
n
f
i
n
a
l
s
i
o
n
switching chamber
diarb
primer
glue
Web: www.easygatesdirect.co.uk Phone: 0845 054 50 70
E-Mail: info@easygatesdirect.co.uk
Address: Easygates Ltd, Unit 16 James Scott Rd B63 2QT
SKL 15-10TT Assembly Instructions
Technical Document Ver 1.0
As of 01.03.2016
6. Fitting the end caps
Cap for the KS2L wiring plug:
Press the cable sheath from the open side into the prepared cable entry of the cap (the sheath should be approx. 2-3mm inside the cap). After that press the
cap onto the plug and verify a firm fitting.
Cap for the KS2W resistor plug:
Press the closed cap onto the terminal plug and verify a firm fitting.
NOTE: A small amount of glue can be optionally applied to the cap before tting.
2-3m m
7. Fitting optional shrink tubing protection
If available, an optional shrink tubing can be
fitted o
ver the end caps to provide enhanced protection of the glue sealing of the KS2 plugs. Firstly a section
of approx. 20-30mm of the T Foot of the pro
file will need
to be trimmed using a cutting tool. Prepare a peice of 20mm diameter shrink tubing approximately
20-30mm in length and place directly over the KS2W plug or pull along the KS2L cable and in to poistion. Then apply heat source to the tubing (e.g. heatgun
or soldering iron tip) until shrink effect has created a tight seal over the glue sealing of the plug.
8. Final assembly check - Repeat the measuring in assembly step 4. to ensure correct resistance
B C
Web: www.easygatesdirect.co.uk Phone: 0845 054 50 70
E-Mail: info@easygatesdirect.co.uk
Address: Easygates Ltd,
Unit 16 James Scott Rd B63 2QT
Technical Document Ver 1.0
As of 01.03.2016
SKL 15-10TT Assembly Instructions
A
  • Page 1 1
  • Page 2 2

ASO Safety Solutions SENTIR edge 15-10 TT Assembly Instructions

Type
Assembly Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI