RCA TP308N User manual

RCA
Brand
RCA
Model
TP308N
Type
User manual

RCA TP308N is a crimping tool designed to help you connect modular plugs to phone wires. With this tool, you can easily cut the cable to the desired length and remove the outer insulation. The wire stripper included in the tool will help you expose the correct amount of color-coded wires without removing the individual wire insulation. Following the wire sequence or the chart provided in the manual, insert the individual wires into the connector until they stop at the tip. Finally, insert the connector with the wires into the crimp cavity of the tool and squeeze down firmly.

RCA TP308N is a crimping tool designed to help you connect modular plugs to phone wires. With this tool, you can easily cut the cable to the desired length and remove the outer insulation. The wire stripper included in the tool will help you expose the correct amount of color-coded wires without removing the individual wire insulation. Following the wire sequence or the chart provided in the manual, insert the individual wires into the connector until they stop at the tip. Finally, insert the connector with the wires into the crimp cavity of the tool and squeeze down firmly.

Crimps modular plugs to phone wire
Fija a presión los enchufes modulares al cable de teléfono
© 2009 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) ® Registered
Marca(s) Registrada(s)
Made in China
www.rcaaccessories.com
DATE
CODE
Lifetime Warranty
Audiovox Electronics Corporation will replace this product,
regardless of how long you own it, if it should fail to perform
to its design specifications. Simply return to the following
address for a replacement: Audiovox Electronics Corpora-
tion, 150 Marcus Blvd., Hauppauge, New York 11788.
Garantía por Vida
Audiovox Electronics Corporation reemplazará este
producto, independientemente de por cuanto tiempo Ud. lo
haya poseído, si se encontrara que el producto no funciona
según las especificaciones. Sencillamente devuélvalo a la
siguiente dirección para obtener un reemplazo: Audiovox
Electronics Corporation, 150 Marcus Blvd., Hauppauge, New
York 11788.
TP308NTP308N
Crimps modular plugs to phone wire
Fija a presión los enchufes modulares al cable de teléfono
Crimping Tool
Engarzador
TP308N NA CAW 00
How to use
1. Use the tool’s wire cutter to cut the cable to the desired length.
2. Use the tool’s wire stripper to remove the outer insulation.
3. Insert the cable into the stripper until it stops. Squeeze down and pull back on the
phone cable. This will expose the correct amount of color-coded wires. DO NOT
remove the individual wire insulation. (see #1)
4. Following your current wire sequence or the chart below, insert the individual
wires into connector until wires stop at tip of connector.
5. Insert the connector with the wires into the crimp cavity of the tool and squeeze
down firmly. Repeat for opposite end. (see #2)
NOTE: Be sure the sequence of wires one end is reversed at the opposite end.
Cómo usar
1. Utilice el cortador de cables de la herramienta para cortar el cable a la longitud
deseada.
2. Utilice el desforrador de cables de la herramienta para retirar el aislamiento exterior.
3. Inserte el cable en el desforrador hasta que tope. Apriete hacia abajo y tire del cable de
teléfono hacia atrás. Esto expondrá la cantidad correcta de cables codificados por
colores. NO retire el aislamiento individual del cable (vea el diagrama 1).
4. Observando la secuencia de cables actual en la tabla a continuación, inserte los cables
individuales en el conector hasta que los cables topen en la punta del conector.
5. Inserte el conector con los cables en la cavidad de engarce de la herramienta y apriete
firmemente hacia abajo. Repita para el extremo opuesto (vea el diagrama 2).
AVISO: Asegúrese que la secuencia de los cables en extremos opuestos sea inversa.
Diagram 1
Diagram 2
Standard Color Codes
Caution
How to Install
Line
1
1
2
3
Green
Red
Disconnect Incoming Line when Making Connections
Black
Yellow
White with Blue Stripes
Blue with White Sripes
White with Orange Stripes
Orange with White Stripes
PHONE
PC
PROJECT
DESIGNER
PROGRAM
Cyan Magenta Yellow Black PMS 185
RCA Carded models - TP308
jt
Illustrator CS3
PROCESS
COLOR
SPOT
COLOR
FILE
DATE
Audiovox JOBS/Jobs WIP/046002 Audiovox/046002_ItemMaster/Tactical
Design/Item L/TP308N NA CAW 00/TP08N NA CAW 00.ai
02/05/2008 4:00:41 PM
NOTE S
LUNAR
Images are from
pickups
1.0
  • Page 1 1

RCA TP308N User manual

RCA
Brand
RCA
Model
TP308N
Type
User manual

RCA TP308N is a crimping tool designed to help you connect modular plugs to phone wires. With this tool, you can easily cut the cable to the desired length and remove the outer insulation. The wire stripper included in the tool will help you expose the correct amount of color-coded wires without removing the individual wire insulation. Following the wire sequence or the chart provided in the manual, insert the individual wires into the connector until they stop at the tip. Finally, insert the connector with the wires into the crimp cavity of the tool and squeeze down firmly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents