INTEK DX-174S Owner's manual

Brand: INTEK

Model: DX-174S

Category: Microphones

Type: Owner's manual

INSTRUCTION MANUAL

MANUALE DI ISTRUZIONI

VHF FM / 80CH / 5W

136-175 MHz

PROFESSIONAL 2-WAY RADIO

PC PROGRAMMABLE

DX-174S

Declaration of Conformity

With the present declaration, we certify that the following products :

INTEK DX-174S

comply with all the technical regulations applicable to the above mentioned products

in accordance with the EC Directives 73/23/EEC, 89/336/EEC and 99/5/EC.

Type of product : VHF PMR Transceiver

Details of applied standards : EN 300 086 -1/-2 1, EN 301 489-1-5

EN 60065

Manufacturer : INTEK S.R.L.

Via G. Marconi, 16

20090 Segrate, Italy

Tel. 39-02-26950451 / Fax. 39-02-26952185

E-mail : [email protected]

Notified Body : EMCCert Dr. Rasek

Boelwiese 5, 91320 Ebermannstadt

Germany

Identification Number : 0678

Contact Reference : Armando Zanni

Tel. 39-02-26950451 / Fax. 39-02-26952185

E-mail : [email protected]

Segrate, 29/03/2007 dr. Vittorio Zanetti

(General Manager)

DECLARATION OF CONFORMITY

EC Certificate of Conformity

(to EC Directive 99/5-89/336-93/68-73/23)

0678

NOTICE !

It is recommended to carefully read this owner’s manual before using the product. This will also help the user to

prevent using the radio in violation of the regulations valid in the country where the product is used, as well as to

avoid any possible interferences with other services.

RoHS

2002/95/EC

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Unpacking and checking parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Preliminary Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Getting acquainted with the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Menu Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

Menu Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Index - Notice

- 1 -

NOTICE !

This transceiver is programmable via PC, using the dedicated software and the PC interface

cable (optional items). Any programming or modification of the original default setting must be

made by a specialised technician or by an authorised service centre. Some functions of this

transceiver might be programmed in violation of the technical rules in force for the use of the

VHF FM band. It is the user’s responsibility to check that any modification to the programming

will be done in compliance with the current regulations. Any modification to the product,

alteration of the internal circuit, of the external structure of the radio or any programming in

violation of the current regulations will automatically void the product certification and your right

to use the product. INTEK S.R.L. declines any responsibility concerning any modification of the

product, made by the user or by a third party, after delivery of the product.

NOTICE !

This transceiver has been factory pre-programmed, in order for the user to test it right after

purchase. It is the user' s responsibility to re-program the radio, in accordance with the

specifications for the frequency channels assigned by the local authority.

English

Thank you !

Thank you for choosing INTEK for your two-way business radios applications This user friendly

transceiver will provide you with clear and reliable communications and will keep your professional

activities at peak efficiency. This transceiver incorporates the latest and most advanced technology, so

you will be pleased with its quality and its technical features.

Important notice !

The use of VHF FM transceivers is subject to the regulations applied in the country where the product

has to be used. As regulations are usually subject to possible modifications, please check the current

regulations in your country with your dealer or local supplier. INTEK does not take any responsibility for

illegal use and operation of this product not in accordance with the regulation of the country where the

product is used.

Safety notice

The user must know and understand the common risks related to the use of transceivers. Do not use

the transceiver in environments at risk of explosion (where there are gas, dusts, smokes, etc.). Do not

use the transceiver in service areas or fuel stations, on board aircrafts, etc.

Cautions

Please observe the following precautions, in order to avoid causing fire, personal injuries or damage to

the radio:

It is suggested that each transmitted message lasts a few minutes only, since very long

transmissions at the maximum transmitter RF output power may overheat the transmitter.

Do not alter or modify in any way your transceiver.

Do not expose the transceiver for a long time to direct sunlight and do not place it close to

heat sources.

Do not expose the transceiver to excessively dusty or damp places, do not place it on

unstable surfaces.

In case of anomalous smell or smoke that leaks out from the transceiver, turn it off immediately

and remove the battery pack. Please contact an authorised service center.

Please do not dispose off used battery with common garbage. Please use the dedicated

disposal containers.

- 2 -

General Information

English

Unpacking and Checking Parts - Supplied Accessories

- 3 -

Unpacking and checking parts

Carefully unpack the product. Please identify all the parts listed below, before wasting the packaging. If

any part is missing or if the packaging shows any damage, please contact your dealer immediately.

Supplied accessories

Rubber flexible antenna with SMA connector

7.2V 1200mAh Li-Ion Rechargeable Battery Pack

Electronic Quick Desk Charger

Belt Clip

Speaker-microphone Jack Cover

User Manual

English

Rubber flexible antenna

with SMA connector

Quick Desk Charger Li-Ion Battery Pack

Belt Clip

Speaker-microphone

Jack Cover

User Manual

Preliminary Steps

- 4 -

Battery charging

Connect the 230VAC adaptor charger to the desk type battery charger

and to a 230VAC outlet. The Red Led will flash to confirm that the charger

is powered.

Insert the empty battery or the transceiver with the battery pack in the

battery charger. Please make sure that the charging contacts of the radio

are connected with the charging contacts of the charger cradle. The Red

Led will light then the device is ready to begin the charging process. The

charging time depends on the battery condition and capacity). When the

charging process has finished, the Red Led lights off and the Green Led

will light. Remove the battery pack or the transceiver from the battery

charger and disconnect it from the AC outlet.

Warning !

The battery is supplied empty and it has to be fully recharged before use.

Some complete cycles of charge/discharge will be necessary in order for the battery to reach a

peak efficiency level.

Please do not charge the battery again when it has just been charged. Otherwise, you may

damage the battery or reduce its life.

The battery charger does not switch OFF automatically when charging is complete, therefore

please remove battery or radio from the charger cradle and disconnect it from the AC outlet.

Do not recharge battery for more than 8 hours, in order to avoid battery overheating.

To install the battery

Please align the two battery slots with the fit runner on the lower side of

the transceiver.

Press the battery downward untill the locker placed on the rear side of the

radio hooks and fastens the battery.

English

To remove the battery

To remove the battery, press the battery locker placed on the rear side of

the radio and slide the battery away from the radio.

Warning !

Please do not waste used batteries into the environment and do not trash them with the common

garbage. Please use the dedicated case for the collection of used up batteries at your supplier.

Do not attempt to open or remove the battery casing.

Do not short the battery terminals or throw the used batteries into fire.

Installing the antenna

Connect the antenna to the antenna connector located on the top panel of

the radio. Gently turn the antenna clockwise until locked.

Warning : Do not touch the antenna and do not move it close to a

microphone cable during transmission, as this might cause malfunction

and damage to the radio.

To install / to remove the belt clip

If necessary, attach the belt clip to the tranceiver, making it slide along the

fit runner placed on the rear side of the battery untill the lock will hook. To

remove the belt clip press the lock and slide the belt clip away from

the battery.

Preliminary Steps

- 5 -

English

- 6 -

Preliminary Steps

English

Install the external earset-microphone jack rubber cover.

If an external earset-microphone is not used, please install the earset-

microphone jack rubber cover.

Install the earset-microphone jack rubber cover, by matching the three

rubber tabs with the holes on the radio, as showed on the drawing.

If the earset-microphone jack rubber cover is removed, radio will not be

splash proof.

To install the external microphone (optional)

To install the external microphone, remove the protection cover of the

external microphone/speaker jack. This cover ensures the watertight

integrity of the transceiver (spray-guard) that will not be ensured after its

removing. Insert the connector of the external microphone into the

right jack.

In order to avoid mulfunction or damage to the transceiver, use only

original microphones. Using non original accessories will authomatically

void the warranty.

Warning !

If an external earset-microphone is used, radio will not be splash proof.

Getting Acquainted with the Product

- 7 -

English

GETTING ACQUAINTED WITH THE PRODUCT

1. Antenna

Rubber flexible antenna with SMA connector.

2. Rotary Switch

Channels and functions selector.

3. Power ON switch and volume control

Switch on the transceiver turning the knob clockwise or counterclockwise to switch it off.

To increase the volume, turn the knob clockwise or counterclockwise to decrease it.

4. LCD Display

Backlighted Dot Matrix LCD Display, provides clear reading and full information on every function

and status of the radio

5. Menu Key

It selects the menu functions.

6. EXIT Key

Exits any status to stand-by status quickly.

7. Keypad

Numeric Keypad.

8. C (Clean) Key

Function key to quickly clean up or exit several functions of the radio.

- 8 -

Getting Acquainted with the Product

9. FUN Key

Function key to quickly access several functions of the radio.

10. UP/DOWN Keys

Channels and menu operation selection keys.

11. Microphone

Built-in microphone.

12. Speaker

Built-in speaker.

13. RX/TX LED Indicator

The LED indicator will light in green colour when the radio is receiving a signal and in red colour

during transmission.

14. PTT key (Push-To-Talk)

To transmit, press and keep pressed the PTT key (14), then speak into the microphone with your

normal voice. To receive release the PTT key (14).

15. LAMP Key

Rubber key to switch ON and OFF the LCD and keypad backlight function.

16. MONITOR Key

Press this key to open the Squelch and release it to close the Squelch.

17. External earset-microphone jack rubber cover

This cover protects the external earset-microphone jack and makes the radio splash proof.

18. Desktop Charger Contacts

English

- 9 -

Getting Acquainted with the Product

English

A B D

C E F G

O NPR

LCD DISPLAY

A. Signal Digital Bar Meter

Indicates the received signal strenght in the receive mode.

B. CT Indication

The CT indication is lighted when the CTCSS function is enabled.

C. T Indication

Non available on this model.

D. DCS Indication

The DCS indication is lighted when the DCS function is enabled.

+ -

Indication

Not available on this model.

Indication

Not available on this model.

G. R Icon

The R icon is lighted when the Reverse function is enabled.

H. Battery Level Indicator

It shows the current battery level condition.

I. CTCSS / DCS Code Number

It shows the CTCSS and DTS Codes setting.

L. Stop Scanning Icon

The channels scanning indicator is lighed when the scanning stops.

M. MONITOR Icon

This icon is lighted when the Monitor key is pressed.

N. Keypad Lock Icon

The Lock icon is lighted when the keypad lock function has been enabled.

- 10 -

Getting Acquainted with the Product - Getting Started

English

O. VOX Indication

The VOX icon is lighted when the VOX function has been enabled.

P. Frequency Reading (25-5-75).

Not available on this model.

Q. RF Digital Meter

It indicates the transmitter RF output power.

R. Dot Matrix Indication

It provides full information on channel and all enabled functions.

S. H Icon

The H icon is lighted when the transmitter is in HIGH POWER mode.

T. S Icon

The S icon is lighted when the automatic channel scan function has been enable.

The S icon will flash if a signal is detected on a channel.

U. F Icon

Not available on this model.

GETTING STARTED

Power ON

Switch on the transceiver turning the Power/Volume knob (3) clockwise until you hear a click, the

transceiver now is in stand-by mode.

Volume adjustment

To adjust the volume, turn the volume knob (3) while using the MONITOR (16) key to listen to the

background noise of the channels.

Channel selection

Select the desired channel, using the UP/DOWN (10) keys or the channels selector (2).

Transmission

In order to transmit, press the PTT (14) key and speak with your normal voice, keeping the microphone

at about 4 cm from your mouth. The LED indicator (13) will light in red color. Release the PTT (14) key

at the end of transmission.

Receiving

Release the PTT (14) key and properly adjusting volume, you will be able to receive the incoming signals.

When receiving a signal, the LED indicator (13) will light in green colour.

Menu Operation

- 11 -

English

MENU OPERATION

In stand-by status, press FUN (9) key to enter the menu.

Press the UP/DOWN (10) keys to choose menu items.

1. Menu function sequence

SCAN ---> T->R (reverse frequency) ---> FREQ (not available) ---> KEYBO (choose keyboard lock

mode) ---> LED (indicator setup) ---> BEEP (warning sound switch setup) ---> POW (RF output power

HI/LOW) ---> SQL (voice level setup) ---> TOT (emission timing setup) ---> VOX (VOX sensitivity setup)

---> STEP (not available).

2. Key Function in the Menu Mode

FUNCTION Key (9) : enter the menu set-up status

C Key (8) : exits the upper menu or quit menu set-up status

UP/DOWN Keys (10) : choose items

MENU/CONFIRMATION Key (5) : confirm item choice or parameter

EXIT Key (6) : exits any status to stand-by status quickly.

SCAN : scanning

In the stand-by status, press the FUN (9) key to display scanning indicator, and when the LCD Display

shows SCAN ?, press the MENU/CONFIRMATION (5) key to start scanning. If signals exist in one

channel, the channel will be displayed. Then press the MENU/CONFIRMATION (5) key, the Two-Way

Radio will stop scanning and remain at the current channel or else, it will start scanning for the next

channel after 2 seconds.

T->R (reverse frequency)

When dual frequency is used to start reverse frequency function, the receiving frequency and emission

frequency will interchange. Press the FUN (9) key then press the UP/DOWN (10) keys. When the LCD

display shows T->R ?, press the MENU/CONFIRMATION (5) key to confirm.

FREQ : not available on this model

KEYBO : Keyboard lock setup

In the stand-by status, press the FUN (9) key and then the UP/DOWN (10) keys to find, and when the

display shows KEYBO?, press the MENU/CONFIRMATION (5) key to enter. You will see two options

available, AUTO and MANUAL.

AUTO: automatic locking

When this option is chosen, the keyboard will be locked automatically when no operation is performed.

MANUAL: manual locking

When this option is chosen, the keyboard cannot be locked automatically.

LED : light setup

In the stand-by status, press the FUN (9) key and then the UP/DOWN (10) keys, and when the display

shows LED ?, press the MENU/CONFIRMATION (5) key to enter. You will see three options available:

AUTO, MANUAL and ON. Press the MENU/CONFIRMATION (5) key to select the desired item.

AUTO: When this option is chosen, the display light will be turned on once you press the key.

MANUAL: When this option is chosen, the display light will not be turned on automatically.

You have to operate the side key manually to use light.

English

ON: When this option is chosen, the display light will be turned on all the time. The light will be on

without any operation.

BEEP : warning sound setup

In the stand-by status, press the FUN (9) key and then the UP/DOWN (10) keys, and when the display

shows BEEP ?, press the MENU (5) key to enter. Press the UP/DOWN (10) keys, and you can see ON

and OFF in turns. You can choose sound ON or OFF by pressing the MENU/CONFIRMATION (5) key.

POW : RF output power setup

In the stand-by status, press the FUN (9) key and then the UP/DOWN (10) keys, and when the display

shows POW ?, press the MENU (5) key to enter. Press the UP/DOWN (10) keys, and you can see H

and L in turns. You can choose high / low power by pressing the MENU/CONFIRMATION (5) key.

SQL : Squelch level setup

In the stand-by status, press the FUN (9) key and then UP/DOWN (10) keys, and when the display shows

SQL ?, press the MENU/CONFIRMATION (5) key to enter. Press the UP/DOWN (10) keys to choose the

desired squelch level and confirm the selection by pressing the MENU/CONFIRMATION (5) key.

TOT : Emission Timing Setup

In the stand-by status, press the FUN (9) key and then the UP/DOWN (10) keys, and when the display

shows TOT ?, press the MENU/CONFIRMATION (5) key to enter. Press the UP/DOWN (10) keys to set

up emitting time limit. The time unit is in seconds. Press the MENU/CONFIRMATION (5) key to confirm

the selection.

VOX : VOX Level Setup

In the stand-by status, press the FUN (9) key and then the UP/DOWN (10) keys, and when the display

shows VOX ?, press the MENU/CONFIRMATION (5) key to enter. Press the UP/DOWN (10) keys to set

up the desired VOX level and press the MENU/CONFIRMATION (5) key to confirm the selection.

STEP : not available on this model

MENU SHORTCUT KEYS

Press the FUN (9) key, then press the numeric key to enter appropriate items. This shortcut function is

same as the items of menu, but they more easy to operate the Two Way Radio.

FUN + 1 Enter the channel/frequency scanning.

FUN + 2 Switches ON/OFF the Reverse Frequency function and exits stand-by status

FUN + 3 Not available.

FUN + 4 The way of keyboard locking (auto/manual) set-up.

FUN + 5 LED light set-up.

FUN + 6 Warning sound setup.

FUN + 7 High/Low RF output power setup.

FUN + 8 Squelch level setup.

FUN + 9 Emission timing setup.

FUN + 0 Swithes on the VOX function and VOX level setup.

FUN +

Keyboard Lock/Unlock

FUN + # Check the receiving/emission frequency of the channels and the CTCSS status.

Menu Operation - Menu Shortcut Keys

- 12 -

Specifications - Optional Accessories

- 13 -

SPECIFICATIONS

General

Frequency 136.000 - 174.9875 MHz

Channels 80

Channel spacing 12.5, 25 KHz

DC input voltage 7.2 VDC

Operating temperature -20/+55°

Dimensions mm 58 x 120 x 35

Weight 235 gr. (with battery and antenna)

Receiver

Sensitivity (12dB Sinad) 0.16 µV

Selectivity 65dB

Intermodulation 60dB

Audio output 500mW

Transmitter

RF output power 5W / 1W

Modulation F3E

Spurious & Harmonics in cmpliance with the R&TTE regulations

Maximum deviation ≤ ±2.5KHz

Frequency Stability ±2.5ppm

OPTIONAL ACCESSORIES

- KME-315 External Earset-Microphone with tie clip

- KME-614 External Earset-Microphone with adjustable ear hook

- KME-801 External Earset-Microphone for security and bodyguard

- KME-100A External Earset-Microphone with tie clip

- KME-200A External Earset-Microphone with flexible boom mic and tie clip

- KME-H115 External Speaker-Microphone (light duty)

- KST-301 External Speaker-Microphone (heavy duty)

- CDDX-174S Programming Kit (PC interface cable and software CD)

User Information

in accordance with art. 13 of the Legislative Decree of 25th July 2005, no. 15 ”Implementation of Directives 2002/95/EC, 2002/96/EC and

2003/108/EC, relative to reduction of the use of hazardous substances in electrical and electronic equipment, in addition to waste disposal”.

The crossed bin symbol shown on the equipment indicates that at the end of its working life the product must be collected

separately from other waste.

The user must therefore take the above equipment to the appropriate differentiated collection centres for electronic and

electro technical waste, or return it to the dealer when purchasing a new appliance of equivalent type, in a ratio of one to one.

Appropriate differentiated waste collection for subsequent recycling, treatment and environment-friendly disposal of the

discarded equipment helps to prevent possible negative environmental and health effects and encourages recycling of the

component materials of the equipment.

Illegal disposal of the product by the user will be punished by application of the administrative fines provided for by the legislative

decree no. 22/1997 (article 50 and following of the legislative decree no. 22/1997).

English

Page is loading ...

INTEK DX-174S Owner's manual

Brand: INTEK

Model: DX-174S

Category: Microphones

Type: Owner's manual

Download PDF

report

in other languages

italiano: INTEK DX-174S Manuale del proprietario

INTEK DX-174S Owner's manual

INTEK DX-174S Owner's manual

in other languages

Related papers

Other documents