Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
deutsch
d
eu
t
sc
h
10 Classic 411.2 OMDD 10/2011
english
english
10/2011 Classic 411.2 OMDD 11
1 Proper use, warranty
The shredder is designed exclusively for
destroying optical data media, e.g. CDs,
DVDs.
The warranty period for the shredder is
2 years. This warranty and guarantee ex-
clude wear and damage caused by improp-
er handling or actions taken by third parties.
2 Safety instructions
Classifi cation
Safety notice Explanation
WARNING Failure to observe
this warning can
lead to serious or
fatal injury.
Notice Failure to observe
this instruction can
cause damage.
WARNING
Risk of injury!
Do not reach into the feed slot.
Risk of injury from being pulled
in!
Keep long hair, loose articles of
clothing, ties, scarves, jewellery,
etc. away from feed opening. Ma-
terial with the tendency to form
loops, e.g. tapes, strapping mate-
rial, etc. must not be shredded.
Before using the machine for the
fi rst time, read the operating man-
ual, and keep it for later use and to
pass on to any subsequent users. Observe
all safety instructions on to the machine.
WARNING
Dangerous for children and
others!
The machine may not be used by
persons (including children under
14 years of age) with limited physi-
cal, sensory or mental capabilities
or with a lack of experience and
knowledge, unless they are supervised by
a responsible person or are instructed by
them on the use of the machine. Children
must be supervised to ensure they do not
play with the machine. Do not leave the
document shredder switched on when it is
unattended.
english
english
12 Classic 411.2 OMDD 10/2011
WARNING
Dangerous mains voltage!
Improper handling of the machine
can lead to an electric shock.
– Before you insert the power plug, make
sure that the voltage and frequency of
your power supply comply with the infor-
mation on the name plate.
– Make sure that the power plug is easily
accessible.
– Make sure that no water gets into the
shredder. Do not immerse the power ca-
ble or the power plug in water.
– Never touch the power plug with wet
hands.
– Never pull the plug out of the socket us-
ing the power cable. Always pull out the
plug directly.
– Only use the machine in a dry room in-
doors. Never operate the machine in
damp rooms or in the rain.
Check the machine and cable
regularly for damage. Switch the
shredder off if it is damaged or
not working correctly or before
relocating or cleaning it and dis-
connect it from the mains.
– Keep the machine, the plug and cable
away from open fi re and hot surfaces.
The ventilation slots must not be blocked
or covered and there must be at least
5 cm space between the shredder and
any wall or furniture.
Notice Danger from improper use
Only operate this machine in accordance
with the instructions outlined in “Proper
use”.
Risk of injury from slivers!
Wear protective goggles when destroying
CDs. Keep the safety element closed when
destroying CDs.
Service work may only be carried
out by HSM Customer Service or
by the service technicians of our
contractual partners.
See page 36 for our customer
service addresses.
english
english
10/2011 Classic 411.2 OMDD 13
1 Inspection door
2 Safety element / splinter protection
3 Safety instructions
4 Cover
5 Membrane keyboard
6 Mains switch
7 Name plate
8 Caution label
9 Bottom frame
10 Roller
11 Guide roller
12 Door
Membrane keyboard
Reversing pushbutton
Cutting system runs in reverse
direction.
Stop pushbutton
Cutting system stops.
Shredder remains in standby
function.
ON pushbutton
Shredder is switched on.
Cutting system runs in feed
direction.
Front door opened
red LED
Paper jam – electric motor
overloaded
red LED
Cut material bag full
red LED
Ready for operation
green LED
3 Machine components
11
10
12
1 4
5
6
9
7
8
0
I
2 3
4 Scope of delivery
• Shredder, ready for connection, in carton
packing, carton on pallet, tied with strap-
ping tape
• 5 bags for shredded material
• Special cutting block oil
• Operating instructions
Acces so ries
• 5 Bags for shredded material,
order No.: 1.442.995.100
• Special cutting block oil 250 ml,
order No.: 1.235.997.403
See page 28 for our customer service
addresses.
english
english
14 Classic 411.2 OMDD 10/2011
Switching the shredder on
• Set mains switch at rear of the
shredder to „I“.
Green LED lights.
Shredder is ready for operation
(standby)
Shredding CDs
Warning!
Keep the safety element closed
when destroying CDs.
• Feed only one CD into the slot of
the safety element.
The shredding pro cess is star ted by a
pho to –cell in the paper feeding opening.
App rox. 3 sec. af ter the last CD is pulled
in the cut ting sy stem au to ma tical ly swit ches
off and returns to standby.
0
I
5 Commissioning
• Open the door of the shredder.
• Take the frame (A) and a waste bag.
• Place the waste bag on the frame and
fold over the top approx. 20 cm.
A
• Slide the frame (with bar B facing the
front of the cupboard) again into the
guide rails.
B
• Close the door of the shredder.
• Plug the machine into a properly
installed socket.
• Undo the wing screws securing the unit
during transportation.
6 Operation
Warning!
Before switching the machine on,
make sure that you observe all
safety instructions.
english
english
10/2011 Classic 411.2 OMDD 15
Swit ching shredder off
• Set mains switch at rear of the
shredder to „0“.
0
I
The shredder can also be started
by pressing the green arrow but-
ton:
• Press briefl y:
Cutting device starts.
Automatic stop approx. 3 seconds
after the last CD was drawn in, or
manual stop when the stop button
is pressed.
• Hold down for longer than
2 seconds:
constant operation without light
barrier function.
The cutting device runs until it is
switched off with the stop button.
Jam
Shredder jammed.
Red LED in the key pad fl ashes.
Shredder reverses automatically.
Notice!
Do not press dashed arrow button and
green arrow button alternately forwards and
backwards. Cutting unit can be damaged.
• Pull CD out of the feeding open-
ing.
If CD is not completely pushed out,
then
• Press dashed arrow button.
CD is pushed out.
• Feed only one CD/DVD.
Electric motor overheated
Red LED on membrane key-
board lights.
Shredder switches off automati-
cally.
• Allow shredder to cool down for
approx. 15 to 20 min.
Front door is open
Red LED on membrane key-
board lights.
Shredder stops automatically.
• Close front door.
Note If the door is opened when
the cutting device is running, the shredder
must be started again using the green but-
ton after the door of the shredder has been
closed.
7 Troubleshooting
english
english
16 Classic 411.2 OMDD 10/2011
Bag for shredded material full
Red LED on membrane key-
board lights.
Shredder stops automatically.
Notice Empty the cut material container,
immediately because if it is too full, malfunc-
tions can occur in the cutting system.
Note Reversing the cutting device
(“Reverse” button) is also possible even
when the shredded material container is full.
• Insert new bag.
Switch off the shredder and pull out the
mains plug. When cleaning only use a soft
cloth and a mild soap-water solution. How-
ever, no water must enter the equipment.
Oil the cutting unit when
cutting performance de-
creases or the device
becomes noisy, or every
time you empty the waste
container:
• Spray special cutting block oil
across the whole width of the cut-
ting system blades.
• Run cutting system forwards and
backwards several times without
feeding CD/DVD.
Dust and particles are shaken off.
8 Cleaning and maintenance
For all other malfunctions, before calling
customer service please check
– if the motor was overloaded
Let the shredder cool down for approx.
15 – 20 mins. before using it again.
– if the light barrier is soiled.
Clean the light barrier in the feed using a
dry brush or cloth.
9 Disposal / Recycling
Electrical and electronic old de-
vices contain a variety of valuable
materials, but also hazardous
substances which were required
for function and safety. Incorrect
disposal or handling can be dan-
gerous to your health and the environment.
Never dispose of old devices in the house-
hold waste. Observe the current applicable
regulations and use the collection points for
returning and recycling electric and elec-
tronic devices. Dispose of all the packaging
materials also in an environmentally-respon-
sible way.
english
english
10/2011 Classic 411.2 OMDD 17
10 Technical data
Applied standards and technical specifi cations:
• EN 55014-1:2006 • EN 61000-4-2:1995 + A1:1998 + A2:2001
• EN 55014-2:1997 + A1:2001 + A2:2008 • EN 61000-4-4:2004
• EN 61000-3-2:2006 • EN 61000-4-5:2006
• EN 61000-3-3:1995 + A1:2001 + A2:2005 • EN 61000-4-6:2007
• EN 13849-1:2008 • EN 61000-4-11:2004
• EN 62233:2008 • EN 50366:2003 + A1:2006
• EN 60950-1:2006 + A11:2009 + A1:2010
EC Declaration of Conformity
The manufacturer HSM GmbH + Co. KG, Austrasse 1 - 9, D-88699 Frickingen hereby declares that the machine,
referred to here as
HSM Classic 411.2 OMDD
corresponds to the health and safety requirements of the following EC directives listed below due to its conception and
design of the version in which it was put into circulation by us:
Low voltage directive 2006 / 95 / EEC
EMC directive 2004 / 108 / EC
Frickingen, 01.03.2011
Rolf Gasteier - Technical Director
Cutting type Cross cut
Shred size (mm) 2.2 x 4.0
Cutting ca pa ci ty per cycle 1 optical data medium, e.g. CD, DVD
Weight 80 kg
Noise level (Idle running/ load) 60 dB(A) / 75 dB(A)
Cutting speed 120 mm/s
Lo ading width (slot of the safety element) 130 mm
Voltage 120 V, 60 Hz
Power 2100 W
Dimensions W x D x H (mm) 595 x 470 x 960
Volume of shredded material bag 146 l
english
english
18 Classic 411.2 OMDD 10/2011
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
italiano
i
t
a
l
i
ano
26 Classic 411.2 OMDD 10/2011
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
polski
polski
34 Classic 411.2 OMDD 10/2011
411.2 OMDD
4
1
1
.
2
O
M
D
D
10/2011 Classic 411.2 OMDD 35
411.2 OMDD
4
1
1
.
2
O
M
D
D
36 Classic 411.2 OMDD 10/2011
HSM GmbH + Co. KG
Austraße 1-9
88699 Frickingen / Germany
Tel. +49 7554 2100-0
Fax. +49 7554 2100 160
www.hsm.eu
HSM (UK) Ltd.
14 Attwood Road / Zone 1
Burntwood Business Park
Burntwood
Staffordshire
WS7 3GJ
Tel. +44(0) 1543.272.480
Fax +44(0) 1543.272.080
www.hsmuk.co.uk
HSM GmbH + Co. KG
Ofi cina Barcelona
C/Tona
Nave n° 15 "El Lago"
Pol. Ind. Monguit
08480 L'Ametlla del Vallès
BARCELONA
Hotline Gratuito
Tel. 00800 44 77 77 66
Fax 00800 44 77 77 67
HSM France SAS
Parc de Genève
240, Rue Ferdinand Perrier
69800 SAINT-PRIEST
FRANCE
Tél: +33 (0) 810.122.633
Fax: +33 (0) 4.72.51.74.81
HSM of America LLC
419 Boot Road
Downingtown, PA 19335
Tel. (484) 237-2308
(800) 613-2110
Fax (484) 237--2309
www.hsmofamerica.com
HSM Polska SP. z.o.o.
ul. Emaliowa 28
02-295 Warszawa
Tel. +48 / 22 862 23 69 / 70
Fax +48 / 22 862 23 68
www.hsmpolska.com
/