HSM 411.2 OMDD 2,2x4mm User manual

Page is loading ...

deutsch

d

eu

t

sc

h

10 Classic 411.2 OMDD 10/2011

english

10/2011 Classic 411.2 OMDD 11

1 Proper use, warranty

The shredder is designed exclusively for

destroying optical data media, e.g. CDs,

DVDs.

The warranty period for the shredder is

2 years. This warranty and guarantee ex-

clude wear and damage caused by improp-

er handling or actions taken by third parties.

2 Safety instructions

Classiﬁ cation

Safety notice Explanation

WARNING Failure to observe

this warning can

lead to serious or

fatal injury.

Notice Failure to observe

this instruction can

cause damage.

WARNING

Risk of injury!

Do not reach into the feed slot.

Risk of injury from being pulled

in!

Keep long hair, loose articles of

clothing, ties, scarves, jewellery,

etc. away from feed opening. Ma-

terial with the tendency to form

loops, e.g. tapes, strapping mate-

rial, etc. must not be shredded.

Before using the machine for the

ﬁ rst time, read the operating man-

ual, and keep it for later use and to

pass on to any subsequent users. Observe

all safety instructions on to the machine.

WARNING

Dangerous for children and

others!

The machine may not be used by

persons (including children under

14 years of age) with limited physi-

cal, sensory or mental capabilities

or with a lack of experience and

knowledge, unless they are supervised by

a responsible person or are instructed by

them on the use of the machine. Children

must be supervised to ensure they do not

play with the machine. Do not leave the

document shredder switched on when it is

unattended.

english

12 Classic 411.2 OMDD 10/2011

WARNING

Dangerous mains voltage!

Improper handling of the machine

can lead to an electric shock.

– Before you insert the power plug, make

sure that the voltage and frequency of

your power supply comply with the infor-

mation on the name plate.

– Make sure that the power plug is easily

accessible.

– Make sure that no water gets into the

shredder. Do not immerse the power ca-

ble or the power plug in water.

– Never touch the power plug with wet

hands.

– Never pull the plug out of the socket us-

ing the power cable. Always pull out the

plug directly.

– Only use the machine in a dry room in-

doors. Never operate the machine in

damp rooms or in the rain.

Check the machine and cable

regularly for damage. Switch the

shredder off if it is damaged or

not working correctly or before

relocating or cleaning it and dis-

connect it from the mains.

– Keep the machine, the plug and cable

away from open ﬁ re and hot surfaces.

The ventilation slots must not be blocked

or covered and there must be at least

5 cm space between the shredder and

any wall or furniture.

Notice Danger from improper use

Only operate this machine in accordance

with the instructions outlined in “Proper

use”.

Risk of injury from slivers!

Wear protective goggles when destroying

CDs. Keep the safety element closed when

destroying CDs.

Service work may only be carried

out by HSM Customer Service or

by the service technicians of our

contractual partners.

See page 36 for our customer

service addresses.

english

10/2011 Classic 411.2 OMDD 13

1 Inspection door

2 Safety element / splinter protection

3 Safety instructions

4 Cover

5 Membrane keyboard

6 Mains switch

7 Name plate

8 Caution label

9 Bottom frame

10 Roller

11 Guide roller

12 Door

Membrane keyboard

Reversing pushbutton

Cutting system runs in reverse

direction.

Stop pushbutton

Cutting system stops.

Shredder remains in standby

function.

ON pushbutton

Shredder is switched on.

Cutting system runs in feed

direction.

Front door opened

red LED

Paper jam – electric motor

overloaded

red LED

Cut material bag full

red LED

Ready for operation

green LED

3 Machine components

11

10

12

1 4

5

6

9

7

8

0

I

2 3

4 Scope of delivery

• Shredder, ready for connection, in carton

packing, carton on pallet, tied with strap-

ping tape

• 5 bags for shredded material

• Special cutting block oil

• Operating instructions

Acces so ries

• 5 Bags for shredded material,

order No.: 1.442.995.100

• Special cutting block oil 250 ml,

order No.: 1.235.997.403

See page 28 for our customer service

addresses.

english

14 Classic 411.2 OMDD 10/2011

Switching the shredder on

• Set mains switch at rear of the

shredder to „I“.

 Green LED lights.

Shredder is ready for operation

(standby)

Shredding CDs

Warning!

Keep the safety element closed

when destroying CDs.

• Feed only one CD into the slot of

the safety element.

 The shredding pro cess is star ted by a

pho to –cell in the paper feeding opening.

 App rox. 3 sec. af ter the last CD is pulled

in the cut ting sy stem au to ma tical ly swit ches

off and returns to standby.

0

I

5 Commissioning

• Open the door of the shredder.

• Take the frame (A) and a waste bag.

• Place the waste bag on the frame and

fold over the top approx. 20 cm.

A

• Slide the frame (with bar B facing the

front of the cupboard) again into the

guide rails.

B

• Close the door of the shredder.

• Plug the machine into a properly

installed socket.

• Undo the wing screws securing the unit

during transportation.

6 Operation

Warning!

Before switching the machine on,

make sure that you observe all

safety instructions.

english

10/2011 Classic 411.2 OMDD 15

Swit ching shredder off

• Set mains switch at rear of the

shredder to „0“.

0

I

The shredder can also be started

by pressing the green arrow but-

ton:

• Press brieﬂ y:

Cutting device starts.

Automatic stop approx. 3 seconds

after the last CD was drawn in, or

manual stop when the stop button

is pressed.

• Hold down for longer than

2 seconds:

constant operation without light

barrier function.

The cutting device runs until it is

switched off with the stop button.

Jam

 Shredder jammed.

 Red LED in the key pad ﬂ ashes.

 Shredder reverses automatically.

Notice!

Do not press dashed arrow button and

green arrow button alternately forwards and

backwards. Cutting unit can be damaged.

• Pull CD out of the feeding open-

ing.

If CD is not completely pushed out,

then

• Press dashed arrow button.

 CD is pushed out.

• Feed only one CD/DVD.

Electric motor overheated

 Red LED on membrane key-

board lights.

 Shredder switches off automati-

cally.

• Allow shredder to cool down for

approx. 15 to 20 min.

Front door is open

 Red LED on membrane key-

board lights.

 Shredder stops automatically.

• Close front door.

Note If the door is opened when

the cutting device is running, the shredder

must be started again using the green but-

ton after the door of the shredder has been

closed.

7 Troubleshooting

english

16 Classic 411.2 OMDD 10/2011

Bag for shredded material full

 Red LED on membrane key-

board lights.

 Shredder stops automatically.

Notice Empty the cut material container,

immediately because if it is too full, malfunc-

tions can occur in the cutting system.

Note Reversing the cutting device

(“Reverse” button) is also possible even

when the shredded material container is full.

• Insert new bag.

Switch off the shredder and pull out the

mains plug. When cleaning only use a soft

cloth and a mild soap-water solution. How-

ever, no water must enter the equipment.

Oil the cutting unit when

cutting performance de-

creases or the device

becomes noisy, or every

time you empty the waste

container:

• Spray special cutting block oil

across the whole width of the cut-

ting system blades.

• Run cutting system forwards and

backwards several times without

feeding CD/DVD.

 Dust and particles are shaken off.

8 Cleaning and maintenance

For all other malfunctions, before calling

customer service please check

– if the motor was overloaded

Let the shredder cool down for approx.

15 – 20 mins. before using it again.

– if the light barrier is soiled.

Clean the light barrier in the feed using a

dry brush or cloth.

9 Disposal / Recycling

Electrical and electronic old de-

vices contain a variety of valuable

materials, but also hazardous

substances which were required

for function and safety. Incorrect

disposal or handling can be dan-

gerous to your health and the environment.

Never dispose of old devices in the house-

hold waste. Observe the current applicable

regulations and use the collection points for

returning and recycling electric and elec-

tronic devices. Dispose of all the packaging

materials also in an environmentally-respon-

sible way.

english

10/2011 Classic 411.2 OMDD 17

10 Technical data

Applied standards and technical speciﬁ cations:

• EN 55014-1:2006 • EN 61000-4-2:1995 + A1:1998 + A2:2001

• EN 55014-2:1997 + A1:2001 + A2:2008 • EN 61000-4-4:2004

• EN 61000-3-2:2006 • EN 61000-4-5:2006

• EN 61000-3-3:1995 + A1:2001 + A2:2005 • EN 61000-4-6:2007

• EN 13849-1:2008 • EN 61000-4-11:2004

• EN 62233:2008 • EN 50366:2003 + A1:2006

• EN 60950-1:2006 + A11:2009 + A1:2010

EC Declaration of Conformity

The manufacturer HSM GmbH + Co. KG, Austrasse 1 - 9, D-88699 Frickingen hereby declares that the machine,

referred to here as

HSM Classic 411.2 OMDD

corresponds to the health and safety requirements of the following EC directives listed below due to its conception and

design of the version in which it was put into circulation by us:

Low voltage directive 2006 / 95 / EEC

EMC directive 2004 / 108 / EC

Frickingen, 01.03.2011

Rolf Gasteier - Technical Director

Cutting type Cross cut

Shred size (mm) 2.2 x 4.0

Cutting ca pa ci ty per cycle 1 optical data medium, e.g. CD, DVD

Weight 80 kg

Noise level (Idle running/ load) 60 dB(A) / 75 dB(A)

Cutting speed 120 mm/s

Lo ading width (slot of the safety element) 130 mm

Voltage 120 V, 60 Hz

Power 2100 W

Dimensions W x D x H (mm) 595 x 470 x 960

Volume of shredded material bag 146 l

english

18 Classic 411.2 OMDD 10/2011

Page is loading ...

italiano

i

t

a

l

i

ano

26 Classic 411.2 OMDD 10/2011

Page is loading ...

polski

34 Classic 411.2 OMDD 10/2011

411.2 OMDD

4

1

.

2

O

M

D

10/2011 Classic 411.2 OMDD 35

411.2 OMDD

4

1

.

2

O

M

D

36 Classic 411.2 OMDD 10/2011

HSM GmbH + Co. KG

Austraße 1-9

88699 Frickingen / Germany

Tel. +49 7554 2100-0

Fax. +49 7554 2100 160

[email protected]

www.hsm.eu

HSM (UK) Ltd.

14 Attwood Road / Zone 1

Burntwood Business Park

Burntwood

Staffordshire

WS7 3GJ

Tel. +44(0) 1543.272.480

Fax +44(0) 1543.272.080

[email protected]

www.hsmuk.co.uk

HSM GmbH + Co. KG

Oﬁ cina Barcelona

C/Tona

Nave n° 15 "El Lago"

Pol. Ind. Monguit

08480 L'Ametlla del Vallès

BARCELONA

Hotline Gratuito

Tel. 00800 44 77 77 66

Fax 00800 44 77 77 67

[email protected]

HSM France SAS

Parc de Genève

240, Rue Ferdinand Perrier

69800 SAINT-PRIEST

FRANCE

Tél: +33 (0) 810.122.633

Fax: +33 (0) 4.72.51.74.81

[email protected]

HSM of America LLC

419 Boot Road

Downingtown, PA 19335

Tel. (484) 237-2308

(800) 613-2110

Fax (484) 237--2309

[email protected]

www.hsmofamerica.com

HSM Polska SP. z.o.o.

ul. Emaliowa 28

02-295 Warszawa

Tel. +48 / 22 862 23 69 / 70

Fax +48 / 22 862 23 68

[email protected]

www.hsmpolska.com

HSM 411.2 OMDD 2,2x4mm User manual

This manual is also suitable for

HSM 411.2 OMDD 2,2x4mm User manual

in other languages

Related papers

Other documents