JVC LX-P1010ZE User manual

Brand: JVC

Model: LX-P1010ZE

Category: Data projectors

Type: User manual

This manual is also suitable for

LX-P1010ZU

Operating Instructions

Please read these instructions completely before operating

this LCD Projector.

Model No.

LCD PROJECTOR

By clicking on the red highlighted words in this document, you

can go directly to a support page.

Top page

LX-P1010ZE

LX-P1010ZU/

screen

This instruction manual provides all the necessary operating

information that you might require. We hope it will help you to

get the most performance out of your new product, that you will

be pleased with your JVC LCD Projector.

For your own protection and prolonged operation of your LCD

Projector, please be sure to read the “Important Safeguards”

carefully, before use.

Dear JVC Customer:

Caution:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician

for help.

Things You Should Know

Continued on the next page...

screen

Warning: (E.U. only)

To assure continued CE Mark compliance, use only the provided

earthed power supply cord and prevent undesirable interference, use

only the provided shielded computer cable with 2 ferrite cores while

connecting LCD to computer and all other connecting cables should be

shielded.

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user‘s authority to operate

this equipment.

Things You Should Know

All product/brand names are trademarks or registered trademarks of the

respective holders.

Declaration of Conformity (USA only)

Model Number: LX-P1010ZU/LX-P1010ZE

Trade Name:

Responsible party: PSEL Dept. JVC America Corp.

Address: 1700 Valley Road Wayne,N.J 07407

Telephone number: (973) 315-5000

This device complies with Part 15 of the FCC Rules, Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC Warning: (USA only)

To assure continued FCC compliance, use only the provided grounded

power supply cord and prevent undesirable interference, use only the

provided shielded computer cable with 2 ferrite cores while

connecting LCD to computer and all other connecting cables should be

shielded. Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate this equipment.

screen

Important Safeguards

Electrical energy can perform many useful functions.

This LCD Projector has been engineered and

manufactured to meet applicable safety standards. But

IMPROPER USE CAN RESULT IN POTENTIAL

ELECTRICAL SHOCK OR FIRE HAZARDS. In order not

to defeat the safeguards incorporated into this LCD

Projector, observe the following basic rules for its

installation, use and servicing.

1 Unplug the LCD Projector from the wall outlet before

cleaning.

2 Do not use liquid cleaners or aerosol cleaners. Use a

soft dry cloth to clean the LCD Projector unit. If the

unit is very dirty, wet a cloth with neutral detergent,

squeeze it tight, wipe the unit with it, and finish by

wiping with a dry cloth. Do not use a chemical duster

or polisher-cleaner because it can adversely affect

the unit and peel the paint coat.

3 Do not use attachments not recommended by JVC,

as they may cause hazards.

Machine Noise Information Ordinance 3. GSGV, January 18, 1991:

The sound pressure level at the operator position is equal or less

than 44 dB (A) according to ISO 7779. (However, this is when the

ambient temperature is less than

30 °C.)

CAUTION: Please read all of these instructions

before you operate your LCD Projector.

Save these instructions for future

reference.

Continued on the next page...

screen

4 Do not use the LCD Projector near water; for example,

near a bathtub, washbowl, kitchen sink, laundry tub, in

a wet basement, near a swimming pool, etc. Never spill

liquid into the LCD Projector.

5 Do not place the LCD Projector on an

unstable cart, stand, or table. The LCD

Projector may fall, which may cause

serious injury to a child or an adult,

and/or serious damage to the unit. Use

only with a cart or stand recommended

by its manufacturer, as being suitable for use with the

LCD Projector.

6 The LCD Projector equipment and cart combinations

should be moved with care. Quick stops, excessive

force, and uneven surfaces may cause the equipment

and cart combination to overturn.

7 Slots and openings in the cabinet back and bottom are

provided for ventilation. To ensure reliable operation of

the LCD Projector and to protect it from overheating,

these openings must not be blocked or covered. These

openings should never be covered with cloth or other

material. The bottom opening should not be blocked by

placing the LCD Projector on a bed, sofa, rug, or other

similar surface. The LCD Projector should not be

placed near or over a radiator or heating vent. The

LCD Projector should not be placed in a built-in

installation such as a bookcase unless proper

ventilation is provided.

Important Safeguards

Continued on the next page...

screen

8 The LCD Projector should be operated only from the

type of power source indicated on the back of the LCD

Projector or in the specifications. If you are not sure of

the type of power supplied to your home, consult your

LCD Projector dealer or local power company.

9 Do not allow anything to rest on the power cord. Do

not place the LCD Projector where the cord will be

walked on.

10 Follow all warnings and instructions marked on the

LCD Projector.

11 As a safety feature, the LCD Projector is equipped with

a 3-prong grounded plug. The 3-prong grounded plug

will fit only into a grounding type power outlet. If the

plug does not fit, use an adaptor that is properly

grounded or have an electrician install a grounded

type outlet. Do not attempt to modify this AC plug.

12 For added protection of the LCD Projector during a

lightning storm, or when it is left unattended or not in

use for long periods of time, unplug it from the wall

outlet and disconnect any cable systems. This will

prevent damage to the projector due to lightning and

power-line surges.

13 Do not overload wall outlets and extension cords with

too many products, because this can result in fire or

electric shock.

Important Safeguards

Continued on the next page...

screen

14 Never push objects of any kind into the LCD Projector

through cabinet slots as they may touch dangerous

voltage points or short out parts, which could result in

a fire or electric shock.

15 Do not attempt to service the LCD Projector yourself.

Opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing

to qualified service personnel.

16 Unplug the LCD Projector equipment from the wall

outlet and refer servicing to qualified service

personnel under the following conditions:

A.When the power cord or plug is damaged or frayed.

B.If liquid has been spilled into the LCD Projector.

C.If the LCD Projector has been exposed to rain or

water.

D.If the LCD Projector does not operate normally when

you follow the operating instructions. Adjust only

those controls that are covered by the operating

instructions; improper adjustment of other controls

may cause damage and will often require extensive

work by a qualified technician to restore the LCD

Projector to normal operation.

E.If the LCD Projector has been dropped or the

cabinet has been damaged.

F. When the LCD Projector exhibits a distinct change in

performance – this indicates a need for service.

Important Safeguards

Continued on the next page...

screen

17 Upon completion of any service or repairs to the LCD

Projector, ask the service technician to perform a

routine safety check to determine that the LCD

Projector is in safe operating condition.

18 When replacement parts are required, be sure the

service technician has used replacement parts

specified by the manufacturer that have the same

characteristics as the original parts. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

19 Air filter should be cleaned every 100 lamp on hours.

The LCD Projector may become too hot if filter is not

cleaned when required.

20 If lens becomes dirty, or smudged, clean with a clean,

dampened cloth. Never touch the lens with your

fingers.

21 Do not look directly into the aperture and lens while

operating as this may result in damage to your eyes.

Important Safeguards

Continued on the next page...

screen

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT

CAREFULLY.

This appliance is supplied with a moulded three pin mains

plug for your safety and convenience. A 13 amp fuse is

fitted in this plug. Should the fuse need to be replaced, please

ensure that the replacement fuse has a rating of 13 amps and

that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of

the fuse.

If the plug contains a removable fuse cover, you must ensure

that it is refitted when the fuse is replaced.

If you lose the fuse cover, the plug must not be used until a

replacement cover is obtained.

A replacement fuse cover can be purchased from your local

JVC Dealer.

If the fitted moulded plug is unsuitable for the socket

outlet in your home, then the fuse should be removed and

the plug cut off and disposed of safely. There is a danger

of severe electrical shock if the cut off plug is inserted

into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as

shown below.

If in any doubt, please consult a qualified electrician.

Important Safeguards

Continued on the next page...

screen

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in

accordance with the following code:

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of this appliance

may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be

connected to the terminal in the plug which is marked with

the letter E or by the Earth symbol

or coloured GREEN

or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal in the plug which is marked with the letter N or

coloured BLACK.

The wire which is coloured BROWN must be connected to

the terminal in the plug which is marked with the letter L or

coloured RED.

Important Safeguards

How to replace the fuse. Open the fuse

compartment with a screwdriver and

replace the fuse.

FUSE

screen

LCD Projector Features

1 Compact & Lightweight

A compact, lightweight liquid crystal projector with the

mobility for mobile presentations as well.

2 Built-in Simple Stand

The Built-in Simple Stand makes it possible to match

the projection angle with the basic use environment of

your office with one-touch ease.

3 Attachable/Removable Swivel Stand

Flexible settings are possible because the projected

image height and left/right tilt can be adjusted freely.

4 One-touch Auto Setup

One-touch image adjustments of RGB input can be

made. The unit detects the condition (up/down) of the

simple stand and automatically corrects keystone

distortion.

5 Compatible with most Personal Computers

The RGB input accepts signals from VGA, SVGA,

XGA, SXGA, and Macintosh compatible computers

with no additional hardware.

6 Supports Component Video (YPBPR) Input

This unit supports progressive DVD and HDTV (480 i/

480 p/625 i/720 p/1 080 i) when components are

connected.

Continued on the next page...

screen

LCD Projector Features

7 Accommodates all International Broadcast Video

Signal Formats

The LCD Projector accepts NTSC/PAL/SECAM/PAL-M/

PAL-N/NTSC4.43 video signal formats.

8 Digital Zoom and Freeze Feature

With remote control operation, you can display a

enlarged portion of the screen up to 5 times. You can

also display a freeze frame (paused) screen.

9 On-board Card Type Wireless Remote Control

Keys necessary for basic operation have been simply

arranged on this compact remote control which can be

stored neatly in the unit.

10 On Screen Display

In addition to English, you can select German, French,

Spanish, Italian, Japanese, and Chinese.

11 Automatic Universal Power Supply

This unit has an operating voltage range of AC 100 V -

240 V.

12 CD-ROM Manual

Because this is an electronic manual, by simply

clicking on the link given for each item of information,

you can go directly to the related page for instructions.

Continued on the next page...

screen

Equipped with a variety of convenient functions

A variety of functions such as the following have been

provided.

•A blue screen is projected (at start-up only) when no signal

is being input.

•Freeze functions for video and audio signals can be toggled

on and off.

•The input signal display function can be toggled on and off.

•16:9 (wide) screen projection is provided.

•Two projection modes (directions) to choose from.

13 Image Quality Select Feature, R/G/B Level Adjust

Feature

With the Image Quality mode switch (Dynamic/

Natural) you can also fine-adjust the white balance of

the projected image.

14 Frontal Air Vent Design

Vented air will not blow on persons located to the side

or in rear of the projector and light leakage will not be

a problem with the Frontal Air Vent design.

LCD Projector Features

screen

Please confirm that the following items are packed in the LCD

Projector box.

They are provided to help you use or set up your LCD Projector.

Contents of LCD Projector Box

(1) LCD Projector

(2) Wireless Remote Control Unit

(3) CR2025 Lithium Battery (Included with the remote control unit)

(10) Lens Cap (Included with the projector)

(4) 2.44 m Power Cord (LX-P1010ZE only)

(7) Computer Cable (mini D-Sub15 pin)

(9) Audio Cable

(14) Quick Reference Manual

(8) Video Cable

(13) CD ROM (Operating Instructions)

(11) Carrying Bag

(12) Swivel Stand

(5) 2.35 m Power Cord (LX-P1010ZE only)

(6) 2.99 m Power Cord (LX-P1010ZU only)

screen

Product Information

LCD Projector

■ Top, right and front

(In case Swivel stand is installed.)

Zoom Ring

Remote

Control

Sensor

Air Filter

Focus Ring

Air Outlet Port

■ Back and bottom

Remote

Control unit

EJECT Knob

Remote

Control unit

Holder

Lamp

Cover

Simple Stand

Security Lock

AC Socket

Speaker

Air Inlet Port

Remote

Control Sensor

Hole for

Swivel Stand

Installation

Labels on the unit are omitted.

Swivel Stand

(Supplied)

screen

Product Information

INPUT

KEYSTONE

ENTER

STATUS

POWER

LCD Projector

Adjust

Buttons

(Also used for

Volume -/+)

ENTER

Button

POWER ButtonPOWER Indicator

STANDBY(RED)

ON(GREEN)

INPUT

Button

KEYSTONE

Button

STATUS Code

Indicator

■ Control panel

screen

Product Information

LCD Projector

RS232C RGB/YPBPR IN AUDIO IN VIDEO IN

S-VIDEO IN

■ Connector panel

The serial connector which is on the terminal board of the

projector conforms to the RS-232C interface specification, so that

the projector can be controlled by a personal computer which is

connected to this connector. Consult your dealer or nearest JVC

representative for details.

Note

RGB/YPBPR

Input

Connector

SERIAL

Connector

Audio

Input

Connector

Video

Input

Connector

S-Video

Input

Connector

screen

POWER

INPUT

SHUTTER

AUTO SETUP

VOLUME

ENTER

FREEZE D.ZOOM

Product Information

POWER

Button

SHUTTER

Button

, , ,

Buttons

VOLUME

-/+ Buttons

FREEZE

Button

INPUT

Button

AUTO SETUP

Button

ENTER

Button

D.ZOOM

Button

Remote Control unit

Transmitter

Battery Holder

screen

Push the tab

Pull out

■ Replacing the battery

Before using the Remote Control Unit

1 While pushing the battery

holder tab to the left, pull out

the battery holder.

2 Insert the battery into the

battery holder so that the + side

is facing upward.

3 Insert the battery holder.

• Do not drop the remote control unit.

• Keep the remote control unit away from liquids.

• Remove the battery if not using the remote control unit for

long periods.

• If the remote control becomes inoperable or does not

operate properly, it is likely due to battery dissipation.

Replace the battery with a new one.

Insert the new lithium battery making sure the polarities (+)

and (-) are correct.

Note

WARNING:

Replace battery with CR2025 only. Use of another battery may

present a risk of fire or explosion.

Caution: Battery may explode if mistreated. Dispose of used

battery promptly. Keep away from children. Do not recharge,

disassemble or dispose of in fire.

Remote Control comes with battery inside. Please remove white

protective film before use.

screen

Before using the Remote Control Unit

If the remote control unit is held so that it is facing directly in front of

the front or rear remote control signal receptors, the operating range

is within approximately 7 m (23 ft) from the surfaces of the

receptors. Furthermore, the remote control unit can be operated

from an angle of ±30 º to the left or right and ±15 º above or below

the receptors. (In this case, the operating range is shortened.)

• If there are any obstacles in between the remote control unit and

the receptors, the remote control unit may not operate correctly.

• If strong light is allowed to shine onto the remote control signal

receptor, or if there are any obstacles between the remote

control signal receptor and the remote control unit, correct

remote control operation may not be possible.

• Ensure that remote control light sensor is not subject to direct

sunlight or light from fluorescent lighting. This may prevent the

remote control from operating correctly, or may cause

malfunctioning.

• If facing the remote control unit toward the screen to operate the

projector, the operating range of the remote control unit will be

limited by the amount of light reflection loss caused by the

characteristics of the screen used.

■ Operating range

Note

30°

15°

30°

approximately

7 m (23 ft)

approximately

7 m (23 ft)

Page is loading ...

JVC LX-P1010ZE User manual

Brand: JVC

Model: LX-P1010ZE

Category: Data projectors

Type: User manual

This manual is also suitable for

LX-P1010ZU

Download PDF

report

JVC LX-P1010ZE User manual

This manual is also suitable for

JVC LX-P1010ZE User manual

Related papers

Other documents