IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING AN ELECTRIC FURNISHING, BASIC
PRECAUTIONS SHOULD ALWAYS BE TAKEN,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING THIS
FURNISHING
DANGER – TO REDUCE THE RISK
OF ELECTRIC SHOCK: ALWAYS UNPLUG THIS
FURNISHING FROM THE ELECTRICAL OUTLET
BEFORE CLEANING.
WARNING – TO REDUCE THE RISK OF
BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS:
1. Unplug from outlet before putting on or taking
off parts.
2. Close supervision is necessary when this furnishing
is used by or near children, in individuals with
certain disabilities.
3. Use this furnishing only for its intended use
as described in these instructions. Do not
use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged
cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped into
water. Return the furnishing to a service center for
examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray)
products are being used or where oxygen
is being administered.
9. To turn off, be sure switch is in the OFF position.
10. Do not leave this furnishing unattended when it is
plugged in.
11. Be sure mirror is not in a position where it can
reflect sunlight; reflected sunlight can cause fire.
12. Do not use on a soft surface such as a bed, where
openings may be blocked.
13. Push switch to OFF position, allow unit to cool
before storing or cleaning.
14. Do not place or store this furnishing where it can
fall or be pulled into a tub or sink.
15. To protect against electrical hazards, do not use
while bathing or in the shower.
16. Never use while sleeping.
17. Never operate the furnishing with the air openings
blocked. Keep air openings free of lint, hair and
the like.
FOR HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
INSTALLATION INSTRUCTIONS
1. Using ⅜-inch drill size, drill two holes in wall the
same distance as two opposite slots in bracket.
Screw into wall stud if possible. If drilling into stud,
use ⅛-inch drill size. Otherwise, insert two
wall anchors in holes.
CAUTION: DO NOT DRILL INTO ELECTRICAL WIRING
THROUGH WALL. CHECK WITH ELECTRICIAN IF
NECESSARY.
2. Screw bracket onto wall, into the anchors.
CAUTION: BE SURE DIRECT SUNLIGHT DOES
NOT STRIKE MIRROR WHEN LEFT UNATTENDED;
REFLECTED SUNLIGHT CAN CAUSE FIRE.
1. Your lighted makeup mirror has a flexible head that
folds back for versatile viewing.
2. This unit operates on 3 AAA batteries (not included).
3. After use, always turn switch to the OFF position,
located on back of unit head.
4. The beauty and design of this mirror complement any
decor. Therefore, you may wish to leave the mirror
displayed. However, if you choose to store the mirror,
see section on Storage for detailed information.
SPECIAL FEATURE
THIS LIGHTED MAKEUP MIRROR USES ENERGY-
SAVING LIFETIME LED BULBS. REPLACEMENT
BULBS ARE NOT REQUIRED.
BATTERY DISPOSAL
When replacing the batteries, make sure you dispose
of the old batteries in accordance with applicable
regulations. They should be disposed of in a location
specifically designated for that purpose so they can
be recycled safely without posing any risk to the
envi
ronment. Do not burn or bury them.
-White type k/o
-Black prints 100%
-Bleed edges
INSTRUCTIONS FOR USING
BATTERIES
• Always purchase the correct size and grade of
battery most suitable for the intended use.
• Replace old batteries of a set at the same time.
• Do not mix old and new batteries. Do not mix
alkaline, standard (carbon-zinc) or rechargeable
(nickel cadmium) batteries.
• Clean the battery compartment by blowing away
any debris prior to battery installation.
• Ensure the batteries are installed correctly with
regard to polarity (+ and -).
• Remove batteries from equipment that will not be
used for an extended period of time.
• When batteries begin to fail, remove promptly.
1-COLOR BREAK
pms black
3 AAA batteries needed (Fig. 1)
TO INSTALL BATTERIES (not included)
1. Loosen screw and remove battery cover.
2. Install 3 AAA new batteries as indicated on battery
compartment (Fig. 1).
3. Replace battery cover by snapping it into place
and tightening the screw.
Bottom Cover INSIDE VIEW