Grizzly G1022SM Owner's manual

10" TABLE SAW

MODEL G1022SM, G1022Z, G1022ZF, G1022ZFX, G1022PRO

INSTRUCTION MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

PRINTED IN TAIWAN.

G1022ZF

&

G1022ZFX

G1022PRO

G1022Z

G1022SM

WARNING

Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities contains

chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other

masonry products.

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to fil-

ter out microscopic particles.

Table Of Contents

PAGE

1. SAFETY

SAFETY RULES FOR ALL TOOLS..........................................................................................................2-3

ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS ................................................................4-7

2. CIRCUIT REQUIREMENTS

110V OPERATION ......................................................................................................................................8

220V OPERATION ......................................................................................................................................9

GROUNDING ............................................................................................................................................10

EXTENSION CORDS ................................................................................................................................10

3. GENERAL INFORMATION

COMMENTARY ....................................................................................................................................11-12

UNPACKING ..............................................................................................................................................13

PIECE INVENTORY ..................................................................................................................................13

HARDWARE BAG CONTENTS ................................................................................................................14

HARDWARE RECOGNITION CHART ......................................................................................................15

CLEAN UP ................................................................................................................................................16

SITE CONSIDERATIONS..........................................................................................................................16

4. ASSEMBLY

BEGINNING ASSEMBLY ..........................................................................................................................17

STAND ..................................................................................................................................................17-18

HANDWHEELS ..........................................................................................................................................19

MOTOR ................................................................................................................................................19-21

WIRING ......................................................................................................................................................21

EXTENSION WINGS ................................................................................................................................22

FENCE RAILS ......................................................................................................................................22-23

FENCE ......................................................................................................................................................23

BLADE........................................................................................................................................................23

BLADE GUARD ....................................................................................................................................24-25

TABLE INSERT..........................................................................................................................................26

5. ADJUSTMENTS

G1022SM FENCE ................................................................................................................................27-29

G1022Z FENCE....................................................................................................................................29-30

BLADE PARALLELISM ........................................................................................................................31-32

45˚ & 90˚ POSITIVE STOPS ....................................................................................................................33

WORM GEAR ............................................................................................................................................34

MITER GAUGE ..........................................................................................................................................34

6. OPERATIONS

PRE-RUN CHECK ....................................................................................................................................35

TEST RUN ............................................................................................................................................35-36

BLADE SELECTION ............................................................................................................................36-37

CROSSCUTTING ................................................................................................................................37-38

RIPPING ....................................................................................................................................................38

DADO OPERATIONS ..........................................................................................................................39-40

RABBET OPERATIONS ......................................................................................................................40-41

7. MAINTENANCE

GENERAL ..................................................................................................................................................42

LUBRICATION ..........................................................................................................................................42

TABLE ........................................................................................................................................................42

V-BELT ......................................................................................................................................................42

WIRING DIAGRAMS ............................................................................................................................43-44

8. CLOSURE ......................................................................................................................................................45

G1022SM MACHINE DATA ......................................................................................................................46

G1022SM PART BREAKDOWNS AND PART LIST ............................................................................47-51

G1022Z MACHINE DATA ..........................................................................................................................52

G1022Z PART BREAKDOWNS AND PART LIST ..............................................................................53-57

G1022ZF/ZFX/PRO MACHINE DATA ......................................................................................................58

G1022ZF/ZFX/PRO PART BREAKDOWNS AND PART LIST ............................................................59-63

TROUBLESHOOTING GUIDE ..................................................................................................................64

PUSH STICK..............................................................................................................................................65

WARRANTY..........................................................................................................................................67-69

-2- G1022 Series Contractor Saws

SECTION 1: SAFETY

Safety Instructions For Power Tools

5. KEEP CHILDREN AND VISITORS

AWAY. All children and visitors should be

kept a safe distance from work area.

6. MAKE WORKSHOP CHILD PROOF with

padlocks, master switches, or by removing

starter keys.

7. DO NOT FORCE TOOL. It will do the job

better and safer at the rate for which it was

designed.

8. USE RIGHT TOOL. Do not force tool or

attachment to do a job for which it was not

designed.

1. KEEP GUARDS IN PLACE and in working

order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking to

see that keys and adjusting wrenches are

removed from tool before turning on.

3. KEEP WORK AREA CLEAN. Cluttered

areas and benches invite accidents.

4. DO NOT USE IN DANGEROUS ENVI-

RONMENT. Do not use power tools in

damp or wet locations, or where any flam-

mable or noxious fumes may exist. Keep

work area well lighted.

For Your Own Safety Read Instruction

Manual Before Operating This Equipment

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

This symbol is used to alert the user to useful information about

proper operation of the equipment.

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This

manual uses a series of symbols and signal words which are intended to convey the level of

importance of the safety messages. The progression of symbols is described below. Remember

that safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures.

NOTICE

G1022 Series Contractor Saws -3-

9. USE PROPER EXTENSION CORD. Make

sure your extension cord is in good condi-

tion. Conductor size should be in accor-

dance with the chart below. The amperage

rating should be listed on the motor or tool

nameplate. An undersized cord will cause a

drop in line voltage resulting in loss of power

and overheating. Your extension cord must

also contain a ground wire and plug pin.

Always repair or replace extension cords if

they become damaged.

Minimum Gauge for Extension Cords

10. WEAR PROPER APPAREL. Do not wear

loose clothing, gloves, neckties, rings,

bracelets, or other jewelry which may get

caught in moving parts. Non-slip footwear is

recommended. Wear protective hair cover-

ing to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use

face or dust mask if cutting operation is dusty.

Everyday eyeglasses only have impact resis-

tant lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold

work when practical. It’s safer than using your

hand and frees both hands to operate tool.

13. DO NOT OVER-REACH. Keep proper foot-

ing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep

tools sharp and clean for best and safest

performance. Follow instructions for lubri-

cating and changing accessories.

15. USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for recom-

mended accessories. The use of improper

accessories may cause risk of injury.

LENGTH

AMP RATING 25ft 50ft 100ft

0-6 18 16 16

7-10 18 16 14

11-12 16 16 14

13-16 14 12 12

17-20 12 12 10

21-30 10 10 No

Safety Instructions For Power Tools

16. REDUCE THE RISK OF UNINTENTION-

AL STARTING. On machines with mag-

netic contact starting switches there is a

risk of starting if the machine is bumped or

jarred. Always disconnect from power

source before adjusting or servicing. Make

sure switch is in OFF position before recon-

necting.

17. MANY WOODWORKING TOOLS CAN

“KICKBACK” THE WORKPIECE toward

the operator if not handled properly. Know

what conditions can create “kickback” and

know how to avoid them.

18. CHECK DAMAGED PARTS. Before fur-

ther use of the tool, a guard or other part

that is damaged should be carefully

checked to determine that it will operate

properly and perform its intended function.

Check for alignment of moving parts, bind-

ing of moving parts, breakage of parts,

mounting, and any other conditions that

may affect its operation. A guard or other

part that is damaged should be properly

repaired or replaced.

19. NEVER LEAVE TOOL RUNNING UNAT-

TENDED. TURN POWER OFF. Do not

leave tool until it comes to a complete stop.

20. NEVER OPERATE A MACHINE WHEN

TIRED, OR UNDER THE INFLUENCE OF

DRUGS OR ALCOHOL. Full mental alert-

ness is required at all times when running

a machine.

21. NEVER ALLOW UNSUPERVISED OR

INEXPERIENCED PERSONNEL TO

OPERATE THE MACHINE. Make sure

any instructions you give in regards to

machine operation are approved, correct,

safe, and clearly understood.

22. IF AT ANY TIME YOU ARE EXPERIENC-

ING DIFFICULTIES performing the intend-

ed operation, stop using the machine!

Then contact our service department or

ask a qualified expert how the operation

should be performed.

-4- G1022 Series Contractor Saws

Additional Safety Instructions For Table Saws

1. ALWAYS use blade guard, splitter and

anti-kickback fingers on all ''through-saw-

ing'' operations. Through-sawing opera-

tions are those when the blade cuts com-

pletely through the workpiece as in ripping

or crosscutting.

2. AVOID KICKBACKS. A condition in which

a piece of wood is thrown back towards an

operator at a high rate of speed. If you do

not have a complete understanding of how

kickback occurs, or how to prevent it, DO

NOT operate this table saw.

3. NEVER reach behind or over the blade

with either hand for any reason.

4. ALWAYS use a push stick for ripping nar-

row stock.

5. NEVER perform any operation ''free-

hand,'' which means using only your hands

to support or guide the workpiece. Always

use either the fence or the miter gauge to

position and guide the work.

6. NEVER stand or have any part of your

body in line with the path of the saw blade.

7. ALWAYS hold the work firmly against the

miter gauge or fence and hold the work

firmly against the table.

8. MOVE the rip fence out of the way when

crosscutting.

9. NEVER use the miter gauge and rip fence

at the same time.

10. NEVER attempt to free a stalled saw blade

without first turning the saw OFF.

11. PROVIDE adequate support to the rear

and sides of the saw table for wide or long

workpieces.

12. AVOID awkward operations and hand

positions where a sudden slip could cause

your hand to move into the blade.

13. IF AT ANY TIME YOU ARE EXPERIENC-

ING DIFFICULTIES performing the intend-

ed operation, stop using the machine!

Then contact our service department or

ask a qualified expert how the operation

should be performed.

14. ALWAYS LOWER OR REMOVE SAW

BLADE WHEN NOT IN USE.

15. NEVER USE A DAMAGED SAW BLADE

OR ONE THAT HAS BEEN DROPPED.

16. USE GREAT CARE WHEN CUTTING

WITH A DADO BLADE. There is a high

degree of risk involved with any dado oper-

ation. Slight movement of the stock away

from the fence will cause kickback.

No list of safety guidelines can be com-

plete. Every shop environment is different.

Always consider safety first, as it applies to

your individual working conditions. Use

this and other machinery with caution and

respect. Failure to follow guidelines could

result in serious personal injury, damage to

equipment or poor work results.

G1022 Series Contractor Saws -5-

Push Sticks

The use of push sticks, particularly when cutting

small or narrow workpieces, provides a double

benefit for saw operators. The push stick pro-

vides added leverage, enabling the operator to

keep the workpiece firmly supported against the

fence and table. At the same time, the push stick

keeps the operator’s hand safely away from the

rotation of the saw blade as shown in Figure 1.

See the template on Page 62 of the manual for

construction details, or purchase one from the

Grizzly catalog.

Zero Clearance Table Inserts

Ideal for use when ripping thin strips or making

bevel cuts, these prevent tearout and jammed

blades by supporting material close to the blade.

Use the standard table insert as a template when

creating additional inserts from wood or plywood.

Blade slot inserts can be custom cut for specific

blade angles by raising the running blade into an

uncut insert at the angle you desire. Be sure to

make an additional slot for the blade splitter. We

also carry a wide selection of table inserts shown

in Figure 2 in the Grizzly catalog. Be sure to hold

the insert firmly in place with a piece of wood

when creating slots. Never hold the table insert

with your hand while cutting new slots.

Safety Accessories

Statistics prove that most common acci-

dents among table saw users can be

linked to kickback. Kickback is typically

defined as the high-speed expulsion of

stock from the table saw toward its opera-

tor. In addition to the danger of the opera-

tor or others in the area being struck by

the flying stock, it is often the case that

the operator’s hands are forced into the

blade during the kickback. The following

can help minimize kickbacks.

1. Use your blade guard and splitter.

2. Never for any reason place your hand

behind the blade. Should kickback

occur, your hand will be pulled into the

blade.

3. Inspect splitter for alignment between it

and your blade.

4. Never use the fence as a guide for cross-

cutting.

5. Never attempt freehand cuts.

6. Use a push stick or featherboard to

maintain control of your workpiece.

7. Feed cuts through to completion.

8. Stand to the side when ripping.

9. Ensure your fence and miter slot are par-

allel to the blade.

If you do not have a clear understanding of

kickback and how it occurs, do not operate

this table saw.

Figure 1. Push Stick.

Push Stick

-6- G1022 Series Contractor Saws

Push Paddles

Push paddles provide added leverage and sup-

port when ripping or crosscutting wide work-

pieces as shown in Figure 3. We offer a number

of push paddles in the Grizzly catalog.

Featherboards

Easily made from scrap stock, featherboards

provide an added degree of protection against

kickback as shown in Figure 4. To make a

featherboard, cut a 30-40° angle at one end of

the board and make a number of end cuts at

approximately

1

⁄4" apart and 2" to 3" deep. We

also offer a number of featherboards in the

Grizzly catalog.

Figure 2. Zero Clearance Table Inserts.

Figure 3. Push Paddles.

Figure 4. Featherboards.

Push Paddles

Featherboards

G1022 Series Contractor Saws -7-

Common Definitions, Terms and Phrases

The following is a list of common definitions, terms and phrases used throughout this manual as they relate

to this table saw and woodworking in general. It is important that you read and become familiar with them

before assembling, adjusting or operating this machine. Your safety is VERY important to us at Grizzly!

Arbor: Metal shaft extending from the drive

mechanism, to which the cutting blade is

attached.

Bevel Edge Cut: Tilting the saw arbor and blade

to an angle between 0° and 45° to perform an

angled cutting operation.

Blade Guard: Metal or plastic mechanism that

mounts over the saw blade to prevent acciden-

tal contact with the cutting edge.

Crosscut: Table saw operation in which the miter

gauge is used to cut across the grain of a piece

of wood.

Dado Blade: Blade or set of blades that attach to

the arbor and are used for cutting grooves and

rabbets.

Dado Cut: Table saw operation that uses a dado

blade to cut a flat bottomed groove into the

face of wood stock.

Featherboard: Safety device used to keep a

board against the rip fence or table. Allows

operator to keep hands away from the saw

blade.

Kerf: The resulting cut or gap made by a saw

blade.

Kickback: A condition in which the wood is

thrown back towards an operator at a high rate

of speed.

Miter Gauge: A component that controls the

wood stock movement while performing a

crosscut. Allows for variation of angle cuts

such as miter cuts used on a picture frame.

Moulding Head: A cutterhead attached to the

arbor. Accepts interchangeable moulding

knives for profile cutting. We DO NOT recom-

mend the use of a moulding head as they

require advanced skills in their operation.

Parallel: Being an equal distance apart at every

point. i.e. the rip fence face is parallel to the

side face of the saw blade.

Non-Thru Cut: A sawing operation that requires

the removal of the blade guard and splitter.

Dado and rabbet cuts are considered Non-

Thru Cuts because the blade does not pro-

trude above the top face of the wood stock.

Always remember to reinstall the blade guard

and splitter after performing a non-thru cut.

Perpendicular: Intersecting and forming right

angles; at right angles to the vertical and hori-

zontal planes. i.e. the blade is perpendicular to

the table surface.

Push Paddle: Safety aid used to push a piece of

wood stock through a cutting operation.

Push Stick: Safety aid used to push a piece of

wood stock through a cutting operation.

Usually used when rip cutting.

Rabbet: Cutting operation that creates an L-

shaped channel along the edge of wood stock.

Splitter: Metal plate attached to the back of the

blade guard that maintains the kerf opening in

the wood when performing a cutting operation.

Standard Kerf:

1

⁄8" gap made with a standard

blade.

Straightedge: A tool used to check the flatness,

parallelness, or consistency of a surface(s).

Thru-Sawing: A sawing operation where the

wood stock thickness is completely sawn

through. Proper blade height usually allows

1

⁄4"

of the top of the blade to extend above the

wood stock.

Thin Kerf:

3

⁄32" gap made with a thin kerf blade.

Rip Cut: A cut made along grain of the wood.

Sacrificial Fence: A piece of wood attached to

the face of the rip fence that is designed to

extend the fence face away from the metal por-

tion of the fence. Used primarily when making

rabbet cuts with a dado blade.

-8- G1022 Series Contractor Saws

SECTION 2: CIRCUIT REQUIREMENTS

110V Operation

The Model G1022SM, Z and ZF motors are

prewired to operate at 110V. See Figure 5 for a

typical 110V installation.

G1022SM and G1022Z:

Under normal 110V use, the Models G1022SM

and Z motors draw approximately 16 amps. We

recommend a 20 amp circuit breaker or a 20 amp

slow-blow fuse.

G1022ZF:

Under normal 110V use, the Model G1022ZF

motor draws approximately 17 amps. We recom-

mend a 20 amp circuit breaker or a 20 amp slow-

blow fuse.

The circuit you use should be dedicated, (i.e., the

machine should provide the only draw from that

circuit). If frequent circuit failures occur when

using this machine, contact our Service

Department or your local electrical contractor.

Because of the high amperage draw of the Model

G1022 Series when wired for 110V, standard

household circuit wiring may not be of a large

enough gauge. A qualified electrician may need to

install a new circuit with wires capable of handling

a 20 amperage draw. Do not attempt to modify an

existing circuit by replacing the circuit breaker

with one rated for a higher amperage.

Figure 5. Typical 110V 3-prong plug and outlet.

G1022 Series Contractor Saws -9-

220V Operation

G1022ZFX and G1022PRO:

The motors supplied with the Models G1022ZFX

and G1022PRO are prewired to operate at 220V.

The Models G1022ZFX and G1022PRO are not

supplied with a plug; therefore, a suitable 220V

plug must be wired in. When operating at 220V,

we recommend using a NEMA-style 6-15 plug

and outlet as shown in Figure 6A. You may also

“hard-wire” the machine directly to your panel,

provided you place a disconnect switch near the

machine. Check the electrical codes in your area

for specifics on wiring requirements.

Under normal use, the motor draws approximate-

ly 13 amps at 220V. We recommend a 15 amp cir-

cuit breaker for 220V operation. This should be

satisfactory for normal use while providing

enough protection against circuit damage caused

by power surges. Always check to see if your cur-

rent wires are capable of handling a 15 amp load.

If you are unsure, consult the advice of a qualified

electrician. Do not attempt to modify an existing

circuit by replacing the circuit breaker with one

rated for a higher amperage.

Figure 6A. Typical 220V 3-prong plug and outlet.

-10- G1022 Series Contractor Saws

We do not recommend the use of extension cords

with 220V equipment. It is much better to arrange

the placement of your equipment and the installed

wiring to eliminate the need for extension cords.

Should it be necessary to use an extension, make

sure the cord is rated Hard Service (grade S) or

better. Refer to the chart in Section 1: Safety

Instructions to determine the minimum gauge for

the extension cord when using either 110V or

220V. The extension cord must also contain a

ground wire and plug pin. Always repair or replace

extension cords when they become worn or dam-

aged.

We have covered some basic electrical

requirements for the safe operation of your

machine. These requirements are not nec-

essarily comprehensive. You must be sure

that your particular electrical configuration

complies with local and state codes.

Ensure compliance by checking with your

local municipality or a licensed electrician.

Grounding Extension Cords

In the event of an electrical short, grounding pro-

vides electric current a path of least resistance to

reduce the risk of electrical shock. This tool is

equipped with an electric cord having an equip-

ment-grounding conductor which must be proper-

ly connected to a grounding plug. The plug must

be plugged into a matching outlet that is properly

installed and grounded in accordance with all

local codes and ordinances.

Improper connections of the electrical-grounding

conductor can result in risk of electric shock. The

conductor with green or green and yellow striped

insulation is the electrical-grounding conductor. If

repair or replacement of the electric cord or plug

is necessary, do not connect the equipment

grounding conductor to a live terminal.

This equipment must be

grounded. Verify that any

existing electrical outlet

and circuit you intend to

plug into is actually

grounded. Under no cir-

cumstances should the

grounding pin from any

three-pronged plug be

removed. Serious injury

may occur.

G1022 Series Contractor Saws -11-

SECTION 3: INTRODUCTION

We are proud to offer the Model G1022 Series

Table Saws. The Model G1022 Series is part of a

growing Grizzly family of fine woodworking

machinery. When used according to the guide-

lines set forth in this manual, you can expect

years of trouble-free, enjoyable operation and

proof of Grizzly’s commitment to customer satis-

faction.

The Model G1022 Series comes in 5 different ver-

sions. The differences are listed on the chart at

the beginning of this manual. The SM, Z, ZF, ZFX

and PRO are all 10" heavy-duty table saws

designed for a wide variety of cutting applications.

They feature ball bearing arbors on a worm gear

mechanism, precision-ground cast iron tables

(except the Model G1022SM), sturdy steel

stands, standard and dado inserts and a miter

gauge.

We also offer many accessories for the table

saws including blades, extension rails, outfeed

rollers and a mobile base. Please refer to our cur-

rent catalog for prices and ordering information.

We are also pleased to provide this manual with

the Model G1022 Series. It was written to guide

you through assembly, review safety considera-

tions, and cover general operating procedures. It

represents our effort to produce the best docu-

mentation possible. If you have any comments

regarding this manual, please write to us at the

address below:

Grizzly Industrial, Inc.

C

/

O Technical Documentation

P.O. Box 2069

Bellingham, WA 98227-2069

Commentary

Item G1022SM G1022Z G1022ZF G1022ZFX G1022PRO

Extension

Wings

Rip Fence

Miter Gauge

Motor

Pre-Wired

Switch

Weight

Dust Port

Sheet Metal

Standard

1.5 H.P.-110/220V

110V

Body Mounted

220 lbs

-

Cast Iron

Shop Fox

®

Classic

Adjustable Slot

2H.P.-110/220V

220V

Rail Mounted

340 lbs

4" Port

Cast Iron

T-Slot Fence

Standard Orange

1.5 H.P.-110/220V

110V

Body Mounted

250 lbs

-

Cast Iron

Shop Fox

®

Adjustable Slot

1.5 H.P.-110/220V

110V

Rail Mounted

290 lbs

4" Port

Cast Iron

Shop Fox

®

Adjustable Slot

2 H.P.-110/220V

220V

Rail Mounted

290 lbs

4" Port

-12- G1022 Series Contractor Saws

Most importantly, we stand behind our machines.

If you have any service questions or parts

requests, please call or write us at the location

listed below:

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: [email protected]

Web Site: http://www.grizzly.com

The specifications, drawings, and photographs

illustrated in this manual represent the Model

G1022 Series as supplied when the manual was

prepared. However, owing to Grizzly’s policy of

continuous improvement, changes may be made

at any time with no obligation on the part of

Grizzly. Whenever possible, though, we send

manual updates to all owners of a particular tool

or machine. Should you receive one, we urge you

to insert the new information with the old and keep

it for reference.

Read the manual before

assembly and opera-

tion. Become familiar

with the machine and its

operation before begin-

ning any work. Serious

personal injury may

result if safety or opera-

tional information is not

understood or followed.

G1022 Series Contractor Saws -13-

Unpacking

If moving this machine

up or down stairs, the

machine must be dis-

mantled and moved in

smaller pieces. Make

sure floor and stair

structures are capable of

supporting the com-

bined weight of the

machine parts and the

people moving them.

The Model G1022 Series is shipped from the

manufacturer in a carefully packed carton. If you

discover the machine is damaged after you have

signed for delivery, immediately call Customer

Service for advice.

When you are completely satisfied with the con-

dition of your shipment, you should inventory its

parts.

The Model G1022 Series

represents a heavy load.

Seek assistance before

beginning assembly.

Some metal parts may

have sharp edges on

them after they are

formed. Please examine

the edges of all metal

parts before handling

them. Failure to do so

could result in injury.

Piece Inventory

After all the parts have been removed from the car-

ton, you should have:

1. Stand Components

2. Extension Wings (2)

3. V-Belt

4. Motor with Pulley

5. Motor Bracket

6. Motor Mount Plate

7. Table Saw Unit

8. Handwheels (2)

9. Arbor Wrench

10. Dado Insert

11. Standard Insert

12. Miter Gauge

14. Blade Guard

15. Blade Guard Bracket

16. Hardware Bags (5)

17. V-Belt Guard and Mounting Hardware

18. V-Belt Guard Bracket

19. Fence Unit (Separate Box W/ZF, ZFX and Pro)

20. Fence Rails (Separate Box)

Figure 6B. (G1022 Layout) Rip fence, rails and

extension wings will vary depending on model.

20

19

2

8

18

4

12

10

11

9

15

3

6

17

14

16

5

7

1

-14- G1022 Series Contractor Saws

Hardware Contents

Qty Description

8 Special Rail Bolt (SM & Z)

8 Fence Rail Spacer (SM & Z)

4 Flat Washer M10 (SM & Z)

4 Hex Nut M10-1.5 (SM & Z)

4 Fence Rail Plug (SM & Z)

6 Flat Washer M10 x M4 Thick

6 Hex Bolt M10-1.5 x 25

2 Hand Wheel Knob

Guide Rail & Extension Wing Hardware Bag

Qty Description

1 Hex Bolt

1

⁄4"-20 x 2"

1 Flat Washer

1

⁄

4"

1 Sleeve

1 Wing Nut

1

⁄4"-20

1 Plastic Belt Guard

Plastic Belt Guard Hardware Bag

Qty Description

4 Hex Bolt M8-1.25 x 25

8 Flat Washer M8

4 Hex Nut M8-1.25

Motor Mount Hardware Bag

Qty Description

40 Carriage Bolt M8-1.25 x 16

4 Hex Bolt M8-1.25 x 19

48 Flat Washer M8

44 Hex Nut M8-1.25

4 Hex Bolt M10-1.5 x 20

4 Hex Nut M10-1.5

4 Flat Washer M10

4 Plastic Foot

4 Hex Bolt #10-24 x

3

⁄8" (ZX, ZFX, PRO)

4 Hex Nut #10-24 (ZX, ZFX, PRO)

4 Lock Washer #10 (ZX, ZFX, PRO)

Floor Stand Hardware Bag

In the event that any nonproprietary parts are

missing (e.g. a nut or a washer), we would be

glad to replace them, or for the sake of expedien-

cy, replacements can be obtained at your local

hardware store.

G1022 Series Contractor Saws -15-

Hardware Recognition Chart

5mm

10mm

15mm

20mm

25mm

30mm

35mm

40mm

45mm

50mm

55mm

60mm

65mm

70mm

75mm

Washer

Lock

Washer

Hex

Nut

Wing

Nut

Phillips

Head

Sheet

Metal

Screw

Setscrew

Phillips

Head

Screw

Thumb

Screw

Slotted

Screw

Countersunk

Phillips

Head

Screw

Cap

Screw

Carriage

Bolt

Hex

Head

Bolt

Button

Head

Screw

Flange

Bolt

Phillips

Head

Hex

Bolt

Lock

Nut

5

⁄16''

1

⁄4''

3

⁄8''

1

⁄2''

5

⁄8''

7

⁄16''

9

⁄16''

3

⁄4''

7

⁄8''

1''

1

⁄4''

1

⁄2''

1

3

⁄4''

2

1

⁄4''

2

1

⁄2''

2

3

⁄4''

3

LINES ARE 1MM APART

LINES ARE

1

⁄16'' INCH APART

5

⁄8''

W

A

S

H

E

R

D

I

A

M

E

T

E

R

9

⁄16''

W

A

S

H

E

R

D

I

A

M

E

T

E

R

1

⁄2''

W

A

S

H

E

R

D

I

A

M

E

T

E

R

12mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

10mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

7

⁄16''

W

A

S

H

E

R

D

I

A

M

E

T

E

R

8mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

3

⁄8''

W

A

S

H

E

R

D

I

A

M

E

T

E

R

5

⁄16''

W

A

S

H

E

R

D

I

A

M

E

T

E

R

1

⁄4''

W

A

S

H

E

R

D

I

A

M

E

T

E

R

#

10

W

A

S

H

E

R

D

I

A

M

E

T

E

R

4mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

6mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

WASHERS ARE MEASURED BY THE INSIDE DIAMETER

MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE

#

10

1

⁄4''

5

⁄16''

3

⁄8''

7

⁄16''

1

⁄2''

5

⁄8''

4mm

6mm

8mm

10mm

12mm

16mm

Use this chart to match up

hardware pieces during the

assembly process!

-16-

G1022 Series Contractor Saws

Clean Up

The unpainted surfaces are coated with a waxy oil

to protect them from corrosion during shipment.

Remove this protective coating with a solvent

cleaner or citrus-based degreaser such as

Grizzly’s G7895 Degreaser. Avoid chlorine-based

solvents as they may damage painted surfaces

should they come in contact. Always follow the

usage instructions on the product you choose for

clean up.

Do not smoke while using

solvents. A risk of explo-

sion or fire exists and may

result in serious personal

injury.

Do not use gasoline or

other petroleum-based

solvents. They have low

flash points which make

them extremely flamma-

ble. A risk of explosion

and burning exists if

these products are

used. Serious personal

injury may occur if this

warning is ignored.

Many of the solvents

commonly used to clean

machinery can be toxic

when inhaled or ingest-

ed. Always work in well-

ventilated areas far from

potential ignition sources

when dealing with sol-

vents. Use care when dis-

posing of waste rags and

towels to be sure they do

not create fire or environ-

mental hazards.

Site Considerations

FLOOR LOAD

Your Model G1022 Series represents a medium

load in a small footprint. Most commercial or

home shop floors should be sufficient to carry the

weight of the Model G1022 Series. If you question

the strength of your floor, you can opt to reinforce

it.

WORKING CLEARANCES

Working clearances can be thought of as the dis-

tances between machines and obstacles that

allow safe operation of every machine without lim-

itation. Consider existing and anticipated machine

needs, size of material to be processed through

each machine, and space for auxiliary stands

and/or work tables. Also, consider the relative

position of each machine to one another for effi-

cient material handling. Be sure to allow yourself

sufficient room to safely run your machines in any

foreseeable operation and keep dust collection

hoses off the floor and out of the way.

LIGHTING AND OUTLETS

Lighting should be bright enough to eliminate

shadows and prevent eye strain. Electrical circuits

should be dedicated or large enough to handle

combined motor amp loads. Outlets should be

located near each machine so power or extension

cords are not obstructing high-traffic areas. Be

sure to observe local electrical codes for proper

installation of new lighting, outlets, or circuits.

Make your shop “child

safe.” Ensure that your

workplace is inaccessible

to youngsters by closing

and locking all entrances

when you are away. Never

allow visitors in your shop

when assembling, adjust-

ing or operating equip-

ment.

G1022 Series Contractor Saws

-17-

SECTION 4: ASSEMBLY

Beginning Assembly

Stand Assembly

Most of your Model G1022 Series has been

assembled at the factory, but some parts must be

assembled or installed after delivery. We have

organized the assembly process into steps.

Please follow along in the order presented here.

TOOLS REQUIRED: High quality square and

straightedge, metric Allen

®

wrench set, flat screw-

driver, Phillips

®

screwdriver, dead blow hammer

and a 6" or 8" adjustable wrench.

Disconnect power to the

machine when perform-

ing any maintenance,

assembly or adjust-

ments. Failure to do this

may result in serious

personal injury.

!

Keep loose clothing

rolled up and out of the

way of machinery and

keep hair pulled back.

Wear safety glasses dur-

ing the entire assembly

process. Failure to com-

ply may result in serious

personal injury.

Some metal parts may

have sharp edges on

them after they are

formed. Please examine

the edges of all metal

parts before handling

them. Failure to do so

could result in injury.

Figure 7. Installing the rubber feet.

The Model G1022 Series is supplied with a

heavy-duty stand. To assemble the stand:

1. Fasten the plastic feet to all four legs using

the M10-1.5 x 25 hex bolts, 10MM flat wash-

ers and M10-1.5 hex nuts as shown in

Figure 7.

2. Locate the long upper and lower side braces

(2 each) and bolt to the legs using the M8-

1.25 x 16 carriage bolts, 8MM flat washers

and M8-1.25 hex nuts as shown in Figure 8.

Do not tighten any stand bolts at this time.

Figure 8. Assembled side panel.

-18- G1022 Series Contractor Saws

Figure 9. Assembled stand section.

3. Attach the short upper and lower side braces

to one of the assembled side panels. Use the

M8 - 1.25 x 16 carriage bolts, 8MM flat wash-

ers and M8-1.25 hex nuts as shown in

Figure 9.

6. Note the location of the mounting holes on

the top of the stand. Turn the table saw body

upside-down and place the dust hood and

adapter assembly over the bottom of the

table saw body with the dust port flange

pointed up.

All Models:

7. Align the holes at the four corners. Place the

assembled stand upside down on the table

saw body, and line up its mounting holes.

Make certain the side of the stand with the “Z

Series” label, if applicable, is on the front side

of the machine (the side with the Grizzly label

and angle scale). Secure with M8-1.25 x 19

hex bolts, 8MM flat washers and M8-1.25

hex nuts, with the dust port sandwiched

between as shown in Figure 11.

4. Bolt the other side panel to the upper and

lower braces using the M8-1.25 x 16 car-

riage bolts, 8MM flat washers and M8-1.25

hex nuts as shown in Figure 10.

G1022ZF and ZFX:

5. Take the black plastic dust hood with the 4"

port and align it with the opening in the

adapter. The bolt holes on each of the four

corners should line up. Using 10-24 x

3

⁄

8"

bolts, 10-24 nuts and

3

⁄16" lock washers to

secure the hood to the adapter.

Figure 10. Stand completely assembled.

Figure 11. Attaching the stand to the saw base.

8. With the help of a second person, flip the

entire table saw unit right side-up and move

it into its working position. Level the stand by

checking all sides for symmetry. Measure

diagonally from top to bottom and adjust the

stand so both diagonals are equal. Tighten

all of the stand bolts.

Stand

Dust Hood

Saw Body

Dust Hood

Adapter

Page is loading ...

Grizzly G1022SM Owner's manual

Grizzly G1022SM Owner's manual

Related papers

Other documents