American Standard 6830.372H.002 Installation guide

Category
Sanitary ware
Type
Installation guide

American Standard 6830.372H.002 is a Heritage Series Spread Lavatory Faucet, certified to comply with ANSI A112.18.1M and covered by U.S. Patent No. 5,819,789. This faucet is designed for durability and ease of use, with features such as a gooseneck spout, aerator, and ergonomic handles. The faucet is available in a variety of finishes to match your bathroom décor, and it comes with all the necessary mounting hardware for easy installation. Whether you're looking to update your bathroom's look or simply replace an old faucet, the American Standard 6830.372H.002 is a great choice.

American Standard 6830.372H.002 is a Heritage Series Spread Lavatory Faucet, certified to comply with ANSI A112.18.1M and covered by U.S. Patent No. 5,819,789. This faucet is designed for durability and ease of use, with features such as a gooseneck spout, aerator, and ergonomic handles. The faucet is available in a variety of finishes to match your bathroom décor, and it comes with all the necessary mounting hardware for easy installation. Whether you're looking to update your bathroom's look or simply replace an old faucet, the American Standard 6830.372H.002 is a great choice.

SPREAD LAVATORY
FAUCETS
Installation
Instructions
6830.372H
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Certied to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
1
024220-0070A
COUPLING NUT
WRENCH
033757-0070A
TEE MOUNTING
KIT
028610-0070A
CARTRIDGE
028610-0070A
ESCUTCHEON KIT
VALVE
ASSEMBLY
012676-YYY0A
HANDLE
FOR 6830372
LOCKNUT
SPOUT
RETAINER
RUBBER
WASHER
RUBBER
GASKET
SINK
SPOUT OR BASE ASSEMBLY
HERITAGE SERIES
012112-0070A
TUBE SEAL &
COUPLING KIT
Turn off water at
main supply.
CAUTION
030258-0070A
VALVE MOUNTING
KIT
012111-0070A
(8” CENTERS) TUBE & TEE KIT
066064-0070A
(12” CENTERS) TUBE & TEE KIT
912711-0070A
O-RING
012669-0070A
SPOUT GASKET
M922880-0070A
AERATOR
M934375 Rev. 1.2 (4/16)
• Insert BASE or SPOUT shank through center hole of SINK, making sure RUBBER GASKET
is properly positioned.
• Assemble RUBBER WASHER, RETAINER, and LOCKNUT onto threads of SPOUT from
underside of SINK.
• Insert LIFT ROD through SPOUT (or BASE) and slot of RETAINER.
• Align SPOUT and tighten LOCKNUT. Be sure slot in BRASS WASHER is positioned to
the rear as shown.
GOOSENECK
SPOUT
030256-0070A
SPOUT
MOUNTING
KIT
CHROME
002
Replace the "YYY" with
appropriate nish code
VALVE INSTALLATION
2
LEDGE
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
BODY
5/16''
MIN.
ESCUTCHEON
RUBBER
RING
CARTRIDGE
SCREEN
SPRING
CLIP
STOP
WASHER
TEE
SCREW
O-RING
O-RING
SHANK
M934375 Rev. 1.2 (4/16)
• Place RUBBER RING into ESCUTCHEON and screw ESCUTCHEON onto VALVE BODY
until snug against internal stop.
• Tighten LOCKNUT to secure VALVE position. Attach COUPLING to TEE and tighten.
• Slide RUBBER FERRULE, FRICTION RING, and COUPLING NUT to outlet of VALVE and tighten
COUPLING NUT rmly. Repeat on other VALVE.
• Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet ofright VALVE
using appropriate connector.
• Prepare TUBE and TEE ASSEMBLY to t available VALVE location. If necessary, cut and/or bend
TUBING carefully. Make sure tube bend is close to the TEE so that it will not effect the compression
joint at the VALVE.
• Remove COUPLING NUT, FRICTION RING, and RUBBER FERRULE from each valve and
slide onto tubing.
• Push TUBING ends into VALVE side outlets. Insert VALVES into mounting holes from underside of SINK.
• Press TEE onto SHANK of SPOUT making certain that the SHANK O-RING is properly seated on SHANK.
• Remove AERATOR.
• With handle in OFF position, turn on water supplies and check all connections for leaks.
• Operate both handles to ush water lines thoroughly. Check spout mounting and hose connections for leaks.
• Turn handles into OFF position and replace AERATOR.
TEST INSTALLED FAUCET
3
SERVICE
4
• To change direction of handle rotation, proceed as follows:
• Turn valve to OFF position.
• Remove INSERT and HANDLE SCREW.
• Slip HANDLE with ADAPTER off.
• Remove SPRING CLIP.
• Lift STOP WASHER, turn 90° and replace.
• Replace SPRING CLIP.
• Replace ADAPTER, HANDLE, SCREW, and INSERT.
• AERATOR may accumulate dirt causing distorted and reduced water ow. Remove AERATOR and rinse clean.
• If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.
• Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water ow.
To clean, rst turn off hot and cold water supplies, then:
• Remove INSERT and HANDLE SCREW.
• Slip HANDLE with ADAPTER off.
• Unscrew CARTRIDGE with wrench.
• Thoroughly rinse plastic SCREEN a base of CARTRIDGE.
• Replace CARTRIDGE until ange is tight against valve body.
• Turn valves OFF.
• Replace ADAPTER, HANDLE, SCREW, and INSERT.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are
trademarks of AS America, Inc. ©2016
1 / 1

American Standard 6830.372H.002 Installation guide

Category
Sanitary ware
Type
Installation guide

American Standard 6830.372H.002 is a Heritage Series Spread Lavatory Faucet, certified to comply with ANSI A112.18.1M and covered by U.S. Patent No. 5,819,789. This faucet is designed for durability and ease of use, with features such as a gooseneck spout, aerator, and ergonomic handles. The faucet is available in a variety of finishes to match your bathroom décor, and it comes with all the necessary mounting hardware for easy installation. Whether you're looking to update your bathroom's look or simply replace an old faucet, the American Standard 6830.372H.002 is a great choice.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document