2. Pyle Pro
  3. PVCD15
PVCD15

Pyle Pro PVCD15 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Pyle Pro PVCD15 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • Where is the best place to mount the volume control?
    What is the maximum power handling capacity of the volume control?
    What type of speaker wire should be used?
    How do I connect the amplifier/receiver to the volume control?
    How do I connect the speakers to the volume control?
    How do I adjust the volume of the remote speakers?
210x285mm
PVCD15
High-Power In-Wall Stereo Volume control
Your PYLE
High-Power
In-wall
stereo
volume
control lets you
adjust
the
volume
on a
pair
speaker
that
are located in a room
separate
from
the
amplifier,so
you can
control
the
sound on
the
spot.
Caution:
thIs
volume
contraIls
limIted
to
a
maxImum
of
120
watts
RMS
per
channel.
Connections
Notes:
•
This
volume
control
can be used with up to
14-gauge
wire.
• Measure the
distance
from the
speaker
to
the
amplifier.
For
distances
of
50
feet
or
less, use
18-gauge
speaker
wire
or
ordinary
lamp
cord.
For
distances
greater
than
50 feet, use
heavier
16-gauge
wire.
Caution:
Letting
strav
wire
ends
touch
an
adjacent
terminal.
the
mounting
brackets
or
screws.
or
the
metal
sides
of
the
electrical
box
could
cause
a
short
cIrcuit
of
damage
a speaker.
Fi
gure
#1
-
-
Amplifier/Receiver
+ +
I I
( ')
~U
E'\
E
'='I
EIUV
I I
~t
l
J~
Speaker B
Speaker A
1.
Strip
off
Y,
inch(12.7mm)
of
insulation
from each end
of
the
amplifier/receiver
and
speaker
wires.
Caution:
Be
sure
to
follow
the
correct
polarltv(+
to
+
and-
to
.)
when
making
connections.
Improper
connections
might
cause
poor
sound
reproduction.
2.
Insert
the
amplifier/receive's
+ and -
speakers
output
wires
into
the
vomume
control's
INPUT
+(positive)
and
-(negative)
terminals,
then
tighten
the
screws.
3.
Insert
the
speaker's
+ and - wire ends
into
volume
control's
OUTPUT
+ and - terminals,
then
tighten
the
screws
.
Mounting the Volume Control
The
volume
control
is
designed
to be mounted in a
standard
electrical
wall box.
Select
a
location
that
is:
•
Within
reach
of
the
speaker
wires
• Easy to reach
for
using
the
volume
control
Caution:
You
must
mount
the
volume
control
In
a
standard
electrical
box.
Do
not
mount
It
dlrectlv
on
a
wall.
Important:
•
Over-Tightening
the
screws
might
damage
the
wall plate.
• Some
electrical
wall
boxes
are a
nonstandard
size.Be
sure
that
you measure the wall box
before
you
mount
the
volume
control.
Once
the
control
has been wired,
it
is ready to be mounted
into
the
wall.
Referring
to Figure #2,
place
the
components
of
the
volume
control
into the wall in
the
order
illustrated.
Use the
enclosed
screws
to hold
the
components
in place.
NOTE:
The
rotary
switch is
shipped
with
the
control
turned as
far
counterclockwise
as
it
will
turn off.
If
you changed this,
return
it
to
the full
counterclockwise
position
before
starting
installation.
Figure #2
ELECTRICAL
BOX
SPEAKER W I
RE
VOLUME
CONTROL
INSTALLA
TI
ON
SCREWS
(supplied)
DECORATOR COVER PLATE
Isuppli
e
d)
COVER PLATE
SCREWS
(supplied)
Operation
Set
the
amplifier/receive's
volume
control to minimum
by
turning
it
fully
counterclockwise.
Then
turn
on
the
amplifier/receiver
and
set
its
volume
control
slightly
above
the
normal
listening
level.
To
increase
or
decrease
the
remote
speaker's
volume, turn
the
wall-mount
volume
control
clockwise
or
counterclockwise.
/