Mighty Mule MM-SL2000B-P User manual

Brand
Mighty Mule
Model
MM-SL2000B-P
Category
Gate Opener
Type
User manual

This manual is also suitable for

Installation Manual for the
Slide Gate Operator System
PROFESSIONAL INSTALLATION RECOMMENDED!
WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds
Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has
hazards associated with its use and therefore by installing this product the installer
and user accept full responsibility for following and noting the installation and
safety instructions. Failure to follow installation and safety instructions can result
in hazards developing due to improper assembly. You agree to properly install this
product and that if you fail to do so Gates That Open, LLC, (“GTO”) shall in no event
be liable for direct, indirect, incidental, special or consequential damages or loss of
prots whether based in contract tort or any other legal theory during the course
of the warranty or at any time thereafter. The installer and/or user agree to assume
responsibility for all liability and use of this product releasing Gates That Open, LLC,
from any and all liability. If you are not in agreement with this disclaimer or do not
feel capable of properly following all installation and safety instructions you may
return this product for full replacement value.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to
install and use this automatic gate operator. This gate operator produces a high level
of force. Stay clear of the unit while it is operating and exercise caution at all times.
All automatic gate operators are intended for use on vehicular gates only.
This product meets and exceeds the requirements of UL 325, the standard which
regulates gate operator safety, as established and made eective March 1, 2000, by
Underwriters Laboratories Inc.
For more information on the GTO/ACCESS SYSTEMS full line of automatic gate
operators and access controls visit our website at www.gtoaccess.com.
©2012 Gates That Open, LLC Printed in China for Gates That Open, LLC. RB270 04.26.12
, LLC
®
SL-2000B
SL-2000B
PROFESSIONAL RESIDENTIAL
ACCESS
SYSTEMS
DO NOT INSTALL THIS OPERATOR WITHOUT
SAFETY EDGES AND ROLLER GUARDS!
Notes
SL-2000B Instruction Manual 04.26.12 i
Class Rating
The GTO SL-2000B Gate Operator is intended for use with vehicular slide gates in single family residential
applications. The operator is system certied to be in compliance with UL 325, current edition, as of publication date.
Vehicular Gate Operator Class Categories:
Residential Vehicular Gate Operator—Class I: A vehicular gate operator (or system) intended for use in a home of
one-to-four single family dwelling, or a garage or parking area associated therewith.
Commercial/General Access Vehicular Gate Operator—Class II: A vehicular gate operator (or system) intended for
use in a commercial location or building such as a multifamily housing unit (ve or more single family units), hotel,
garages, retail store, or other building servicing the general public.
Industrial/Limited Access Vehicular Gate Operator–Class III: A vehicular gate operator (or system) intended for use
in an industrial location or building such as a factory or loading dock area or other locations not intended to service
the general public.
Restricted Access Vehicular Gate Operator–Class IV: A vehicular gate operator (or system) intended for use in
a guarded industrial location or building such as an airport security area or other restricted access locations not
servicing the general public, in which unauthorized access is prevented via supervision by security personnel.
Converting Metric Units to English Equivalents
When You Know Multiply By To Find Symbol
centimeters 0.3937 inches in. (or ")
meters 3.2808 feet ft. (or ')
kilograms 2.2046 pounds lb. (or #)
Converting English Units to Metric Equivalents
When You Know Multiply By To Find Symbol
inches 2.5400 centimeters cm
feet 0.3048 meters m
pounds 0.4535 kilograms kg
Converting Temperature
deg. Celsius (°C x 1.8) + 32 deg. Fahrenheit °F
deg. Fahrenheit (°F-32) ÷ 1.8 deg. Celsius °C
Serial Number: ___________________________________ Date of Purchase: ________________
Place of Purchase: ___________________________________________________________________
Please record the following information product serial number (located on right side of control box), be sure to
keep all receipts for proof of purchase. Refer to this information when calling GTO for service or assistance
with your automatic gate opener.
FOR YOUR RECORDS
ii SL-2000B Instruction Manual 04.26.12
Thank you for purchasing a GTO/ACCESS SYSTEMS SL-2000B. When correctly installed and properly used,
your SL-2000B operator will give you many years of reliable service. Please read the following information
to ensure you have the correct system for your particular needs. This manual will enable you to properly
install your SL-2000B Automatic Gate Operator.
The SL-2000B operator is designed for installation on a slide-to-open single leaf gate. The gate must not
exceed 30 feet in length nor weigh more than 1000 pounds* (please see Technical Specications on page
1). The SL-2000B operator can be used on vinyl, aluminum, chain link and wrought iron gates.
The SL-2000B operator accommodates extra transmitters, digital keypads, solar panels, push buttons, and
other access control products. These optional accessories are noted with the
symbol.
The SL-2000B operator features adjustable stall force. This safety feature makes the gate stop and reverse
direction within two seconds when it comes in contact with an obstruction. The “MIN” setting means the
gate will exert the minimum force on an obstruction before it stops and reverses direction.
The SL-2000B operator also has an adjustable auto-close feature. It can be set to remain open from 3 to
120 seconds before automatically closing. Pressing the transmitter button at any time after the gate fully
opens will cause it to close immediately. “OFF” is the factory setting; meaning the gate will stay open until
you press the transmitter button (or keypad, etc.) again.
Please call GTO at (800) 543-GATE [4283] or (850) 575-0176 for more information about our GTO/ACCESS
SYSTEMS professional line of gate operators and accessories. Our Sales Department will be glad to give
you the name and phone number of a GTO/ACCESS SYSTEMS dealer near you.
BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPERATOR:
Read these instructions carefully and completely to become familiar with all parts and installation
steps. You must read the installation manual for detailed instructions on gate operator safety
and proper use of the gate operator.
24/7 Troubleshooting Wizard: http://support.gtoinc.com
PLEASE READ THIS FIRST
, LLC
®
GTO Accessories are noted with this symbol in this Installation
Manual. Information about accessories can be found on page 25
and at www.gtoaccess.com.
SL-2000B Instruction Manual 04.26.12 iii
Table of Contents
Class Rating ............................................................................................................................................ i
Please Read This First ........................................................................................ii
Important Safety Instructions ...................................................................................................... iv
Solar Panel and Gate Activity Chart ................................................................................... page 1
Technical Specications for SL-2000B ...............................................................................page 2
Parts Identication (Single Gate Operator) ....................................................................page 3
Single Gate Operator Installation ......................................................................................page 4
Overview and Gate Preparation ..................................................................................page 4
Suggested Conduit & Wiring and Mounting the Legs .........................................page 5
Determining the Mounting Position and Mounting the Operator .................page 6
Installing the Chain .......................................................................................................... page 7
Disconnecting Operator Chain for Manual Operation of Gate ........................page 7
Powering the System ............................................................................................................. page 8
Installation of the Transformer ......................................................................................page 8
Connecting Solar Panel (s) ..............................................................................................page 9
Control Board Settings ..................................................................................................page 10
Potentiometers .................................................................................................................page 11
Program Your Personal Transmitter Setting ..................................................................page 12
Mounting the Receiver ........................................................................................................page 13
Adjusting the Limit Switches ............................................................................................page 14
Connecting Safety Devices ................................................................................................page 15
Connecting Accessories .......................................................................................................page 16
Attaching the Housing .........................................................................................................page 17
Dual Gate System Installation ...........................................................................................page 18
Preparing the Gates .......................................................................................................page 19
Wiring the Second Operator ......................................................................................page 20
Control Board Settings for Dual Install ...................................................................page 21
Maintenance ...........................................................................................................................page 22
Warranty and Repair Service .............................................................................................page 23
Troubleshooting Guide ........................................................................................................page 24
Accessory Catalog ................................................................................................................page 25
IMPORTANT SAFETY INSTRUCTIONS
iv SL-2000B Instruction Manual 04.26.12
Because automatic gate operators produce high levels of force, consumers need to know the potential
hazards associated with improperly designed, installed, and maintained automated gate operator
systems. Keep in mind that the gate operator is just one component of the total gate operating system.
Each component must work in unison to provide the consumer with convenience, security, and safety.
This manual contains various safety precautions and warnings for the consumer. Because there are
many possible applications of the gate operator, the safety precautions and warnings contained in
this manual cannot be completely exhaustive in nature. They do, however, provide an overview of the
safe design, installation, and use of this product. CAREFULLY READ AND FOLLOW ALL SAFETY
PRECAUTIONS, WARNINGS, AND INSTALLATION INSTRUCTIONS TO ENSURE THE SAFE
SYSTEM DESIGN, INSTALLATION, AND USE OF THIS PRODUCT.
Precautions and warnings in this manual are identified with this warning symbol. The symbol
identifies conditions that can result in damage to the operator or its components, serious injury, or
death.
Because GTO automatic gate operators are only part of the total gate operating system, it is the
responsibility of the installer/consumer to ensure that the total system is safe for its intended
use.
How To Manually Open and Close the Gate:
CAUTION: Disconnect the operator chain ONLY when the power switch and control board is off.
Disconnecting the Operator
1. Lift the quick release pins UP, then pull them OUT of the chain brackets (see illustration).
2. Lay the chain down and manually slide the gate to the desired position.
CAUTION: Because the GTO gate
operator is battery powered, disconnect the
operator ONLY when the power switch on
the contol box is turned OFF. Unplugging
the transformer does not turn power to the
operator OFF.
NOTE: To prevent unauthorized removal of the
quick release pins, install [FM345] pin locks
(see accessory catalog pg. 25) above the quick
release pins in both chain brackets.
Quick Release Pin (211IH)
Insert pin lock (FM345)
shaft through the
Chain Bracket.
Secure pin lock
above the Quick
Release Pin.
Chain Bracket (204IH)
IMPORTANT SAFETY INSTRUCTIONS
SL-2000B Instruction Manual 04.26.12 v
For The System Designer
WARNING: To reduce the risk of injury or death:
1. READ AND FOLLOW ALL INSTRUCTIONS. Failure to meet the requirements set forth in the instruction
manual could cause severe injury or death, for which the manufacturer cannot be held responsible.
2. When designing a system that will be entered from a highway or main thoroughfare, make sure the system is
placed far enough from the road to prevent traffic congestion.
3. The gate must be installed in a location that provides adequate clearance between it and adjacent structures
when opening and closing to reduce the risk of entrapment.
4. The gate and gate operator installation must comply with any applicable local codes.
I. Before Installation
1. Verify this operator is proper for the type and size of gate, its frequency of use, and the proper class rating.
2. Make sure the gate has been properly installed and slides freely in both directions. Repair or replace all worn or
damaged gate hardware prior to installation. A freely moving gate will require less force to operate and will
enhance the performance of the operator and safety devices used with the system.
3. Review the operation of the system to become familiar with its safety features. Understand how to disconnect the
operator for manual gate operation (page iii).
4. This gate operator is intended for vehicular gates ONLY. A separate entrance or gate must be installed for
pedestrian use (page vi).
5. Always keep people and objects away from the gate and its area of travel. NO ONE SHOULD CROSS THE
PATH OF A MOVING GATE.
II. During Installation
1. Install the gate operator on the inside of the property and fence line. DO NOT install an operator on the outside
of the gate where the public has access to it.
2. Be careful with moving parts and avoid close proximity to areas where fingers or hands could be pinched.
3. Devices such as contact sensors (safety edges) and non contact sensors (photo beams) provide
additional protection against entrapment.
4. If push buttons or keypads are installed, they should be within sight of the gate, yet located at least 10 feet from
any moving part of the gate. Never install any control device where a user will be tempted to reach through
the gate to activate the gate operator.
5. Do not activate your gate operator unless you can see it and can determine that its area of travel is clear of
people, pets, or other obstructions. Watch the gate through its entire movement.
6. Secure outdoor or easily accessed gate operator controls in order to prohibit unauthorized use of the gate.
IMPORTANT SAFETY INSTRUCTIONS
vi SL-2000B Instruction Manual 04.26.12
III. After Installation
1. Attach the warning signs (included) to each side of the gate to alert the public of auto matic gate operation. It
is your responsibility to post warning signs on both sides of your gate. If any of these signs or warning decals
become damaged, illegible or missing, replace them immediately. Contact GTO for free replacements.
2. The gate is automatic and could move at any time, posing a serious risk of entrapment. No one should be in
contact with an activated gate when it is moving or stationary.
3. Do not attempt to drive into the gate area while the gate is moving; wait until the gate comes to a complete
stop.
4. Do not attempt to “beat the gate” (drive through) while the gate is closing. This is extremely dangerous.
5. Do not allow children or pets near your gate. Never let children operate or play with gate controls. Keep
ALL gate controls away from children and unauthorized users; store controls where children and unauthorized
users do not have access to them.
6. KEEP GATE AND GATE Operator PROPERLY MAINTAINED. Always turn power to operator OFF before
performing any maintenance. Regularly lubricate rollers.
7. To operate this equipment safely, YOU must know how to disconnect the operator for manual gate operation
(page iii). If you have read the instructions and still do not understand how to disconnect the operator, contact
the GTO Service Department.
8. Disconnect the operator ONLY when the power is TURNED OFF and the gate is NOT moving.
9. Make arrangements with local fire and law enforcement for emergency access.
10. Distribute and discuss copies of the IMPORTANT SAFETY INSTRUCTIONS section of this manual with all
persons authorized to use your gate.
11. IMPORTANT: Save these safety instructions. Make sure everyone who is using or will be around the gate
and gate operator are aware of the dangers associated with automated gates. In the event you sell the
property with the gate operator or sell the gate operator, provide a copy of these safety instructions to
the new owner.
Should you lose or misplace this manual, a copy can be obtained by downloading one from the GTO web site
(www.gtoaccess.com), by contacting Gates That Open, LLC., at 3121 Hartsfield Road, Tallahassee, Florida 32303
or by calling 1-800-543-4283 and requesting a duplicate copy. One will be provided to you free of charge.
Required Safety Precautions for Gates
Install Warning Signs
Warning signs alert people of automatic gate operation and are required when installing the GTO Gate Operator. The
Warning Signs included must be installed on both sides of each gate. Furthermore, a walk-through gate must be installed
for pedestrian traffic.
Entrapment Protection
GTO’s inherent obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily
injury in some circumstances. For this reason, safety devices such as safety edge sensors (or photoelectric sensors),
which stop and reverse gate direction upon sensing an obstruction, are suggested for enhanced protection against
entrapment.
IMPORTANT SAFETY INSTRUCTIONS
SL-2000B Instruction Manual 04.26.12 vii
Secondary Means of Protection Against Entrapment
As specified by Gate Operator Safety Standard, UL 325 (30A.1.1), automatic gate operators shall have an inherent
entrapment sensing system, and shall have provisions for, or be supplied with, at least one independent secondary
means to protect against entrapment. The SL-2000B utilizes Type A, an inherent (i.e., built-in) entrapment sensing system
as the primary type of entrapment protection. Also, the SL-2000B has provisions for the connection of Type B1 or B2
protection to be used as the secondary type of entrapment protection, if desired.
1. For gate operators utilizing a non-contact sensor (e.g., photo-electric sensor– Type B1) in accordance with UL
325 (51.8.4 [h]):
A. Refer to the sensor manufacturer’s instructions on the placement of non-contact sensors for each type of
application.
B. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the
gate is still moving.
C. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the
perimeter reachable by a moving gate or barrier.
2. For gate operators utilizing a contact sensor (e.g., safety edge sensor– Type B2) in accordance with UL 325
(51.8.4 [i]):
A. One or more contact sensors shall be located at the leading edge, bottom edge, and post edge, both inside and
outside of a vehicular slide gate system.
B. A hard wired contact sensor shall be located and its wiring arranged so that the communication between the
sensor and the gate operator is not subjected to mechanical damage.
C. A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for
entrapment protection functions shall be located where the transmission of the signals are not obstructed or
impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall
function under the intended end-use conditions.
You may want to consider adding photo beams to your installation. GTO Photo Beams [R4222] provide a “non contact”
means of entrapment protection.
ENTRAPMENT ALARM (UL 325; 30A.1.1A)
The SL-2000B Gate Operator is designed to stop and reverse within 2 seconds when the gate comes in contact with
an obstruction. Additionally, these operators are equipped with an audio entrapment alarm which will activate if the
unit obstructs twice while opening or closing. This alarm will sound for a period of 5 minutes, or until the operator
receives an intended signal from a hard wired entry/exit source (e.g. push button control or keypad) and the gate
returns to a fully open or fully closed position. Turning the power switch on the control box OFF and back ON will also
deactivate the alarm. Wireless controls such as transmitters and wireless keypads will not deactivate the alarm.
CAUTION
AUTOMATIC GATE
STAND CLEAR
1-800-543-GATE
®
Operator
Contact Sensor
Warning Sign
Contact Sensor
Contact Sensor
Roller Guard
Roller Guard
Pedestrian Gate
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Vehicle Gate
IMPORTANT SAFETY INSTRUCTIONS
viii SL-2000B Instruction Manual 04.26.12
Required Safety Precautions for Gates
Install Screen Guard Over Gate and Fence
Injuries may occur when people place their hands, arms, legs, etc., through openings in the gate grill when the gate is
operated, trapping them between the grill and the fence post (or fence). All openings of a horizontal slide gate must be
guarded or screened to prevent a 2 ¼” diameter sphere from passing through openings anywhere in the gate. This screen/
guard must also be installed over the portion of adjacent fence that the gate covers in the open position.
Screening will prevent access through openings in areas where the gate may travel.
Roller guard to prevent
pinch point hazard.
Roller guard to prevent
pinch point hazard.
Contact Sensor
Roller Guards
Injuries occur
when people get
their hands caught
between the gate
and the roller. Roller
guards or enclosed
tracks must be
installed to prevent
this pinch point
hazard.
The warning
signs (left) must
be installed on
both sides of
the gate.
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Entrapment Protection
GTO’s internal obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily injury.
For this reason, safety devices such as safety edges MUST be installed. Furthermore, a pedestrian gate must be installed
if walk-through traffic is expected near the gate.
Contact Sensor
Screen Mesh
Contact Sensor Contact Sensor
CAUTION
AUTOMATIC GATE
STAND CLEAR
1-800-543-GATE
®
Operator
Contact Sensor
Warning Sign
Contact Sensor
Contact Sensor
Roller Guard
Roller Guard
Pedestrian Gate
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Vehicle Gate
IMPORTANT SAFETY INSTRUCTIONS
SL-2000B Instruction Manual 04.26.12 ix
These warning labels should be found at the locations specified below. If any of them are missing,
immediately contact your installer for replacements.
WARNING
!
• Fingers, hands, and
loose clothing may be
dragged into chain
sprockets.
• Fingers and hands can
be injured by rotating
sprockets.
• Keep hands, fingers,
and loose clothing
away from chain and
chain opening in
operator housing.
• Fingers, hands, and loose clothing
may be dragged into chain sprockets.
• Fingers and hands can be injured by
rotating sprockets.
•
Keep hands, fingers, and loose clothing
away from chain and sprockets.
WARNING
!
warning labels (3). Located on both sides and back
of operator housing
warning label located on top
of control box
• Moving parts inside are capable of
causing injury to fingers and hands.
• DO NOT remove operator housing.
• Consult your safety manual before
making adjustments.
•
For service, call an experienced technician.
AUTOMATIC GATE OPENERS 1-800-543-GATE
WARNING
!
warning label located on front of operator housing
product identification and manual operation instruction
label installed on control box cover
RB2002
Maximum Gate: 1000 lb. (453.4 kg); 30 ft. (9.1 m)
Voltage: 12 Vdc; Frequency: 0 Hz; Power: 93.2 W
Class I Vehicular Slide Gate Operator
Serial Number: SL2000-xxxxxxx
9901178
Conforms to UL 325 STANDARDS
Certified to CAN/CSA-C22.2 No.247-92
Disconnect operator ONLY when the gate is NOT moving.
TO MANUALLY OPEN AND CLOSE THE GATE:
1. Lift quick release pins UP, then pull them OUT of chain brackets.
2. Lay chain down and manually slide gate to desired position.
Series
GTO, LLC. Tallahassee, Florida USA
L
I
S
T
E
D
USC
IMPORTANT SAFETY INSTRUCTIONS
x SL-2000B Instruction Manual 04.26.12
These warning labels should be found at the locations specified below. If any of them are missing,
immediately contact your installer for replacements.
• Fingers, hands, and
loose clothing may be
dragged into chain
sprockets.
• Fingers and hands can
be injured by rotating
sprockets.
• Keep hands, fingers,
and loose clothing
away from chain and
sprockets.
WARNING
!
• Adjusting limit switches with power on will
activate gate.
• Injury may result if fingers get caught under
switch plate while adjusting switches.
•
Use extreme caution when adjusting switches.
WARNING
!
• Fingers, hands, and loose clothing
may be dragged into chain sprockets.
• Fingers and hands can be injured by
rotating sprockets.
• Keep hands, fingers, and loose clothing
away from chain and sprockets.
WARNING
!
warning label located
on limit switch plate
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
warning signs (2) to be installed on each side of the gate
(3–5 feet above the bottom of the gate)
warning sign located (inside housing)
over the top sprocket at back of operator
warning label located (inside housing) next to
sprockets on back of operator
SL-2000B Instruction Manual 04.26.12 1
Winter Ratings Watts Zone 1 Zone 2 Zone 3
SL-2000B 10 4 8 13
SL-2000B 20 8 16 26
Dual SL-2200B 20 4 8 13
Estimated Maximum Number of Cycles Per Day
Before You Begin...
1. Determine Charging Option for Battery: Transformer OR Solar
NEVER USE TRANSFORMER AND SOLAR PANEL(S) AT THE SAME TIME.
It will damage the control board.
IMPORTANT:
• TheSL-2000B12voltbatterymustbechargedbyeitherconnectingthetransformer(included)or
solar panel kit [FM123] to the control board.
• Thetransformerisdesignedforindooruse.Ifthetransformercanbepluggedonlyintoanoutside
electrical outlet, a weatherproof cover/housing (available at local electrical supply stores) must be
used.
•Ifyourgateismorethan1000ft.fromanACpowersource,youwillneedtouseatleast10watts
solar charging power to charge the battery [FM123]. Refer to the Solar Panel and Gate Activity
chart below.
• AlllowvoltagewireusedwiththeGTOGateOperatormustbe16gaugedualconductor,stranded,
direct burial wire [RB509]. Do not run more than 1000 ft. of wire.
The table and map
illustrate the maximum
number of gate cycles
to expect per day in a
particular area when
using from 10 to 20
watts of solar charging
power. The gures
shown are for winter
(minimum sunlight).
Accessories connected to your system
will draw additional power from the
battery.
NOTE: A minimum of 10 watts solar
charging power is needed to charge the
batteries.
10 Watt Solar Panel [FM123]
5 Watt Solar Panel [FM122]
Solar Panel and Gate Activity Chart
2 SL-2000B Instruction Manual 04.26.12
SL-2000B TECHNICAL SPECIFICATIONS
DRIVE
• Poweredbya12Vmotorwithintegralcasehardenedsteelgearreducer.Motorspeedreducedto90rpm.
• Gatevelocity:1ft/second.
POWER
• Twobladestylefusesratedfor20A.
NOTE: The transformer should not be connected directly to any battery. Transformer must be connected to the
control board with a minimum of 16 gauge, stranded, dual conductor, direct burial low voltage wire. Do not replace
fuses with higher ampere rated fuses; doing so will void the warranty and may damage the control board.
• SolarPanelChargercanonlybeusedontheSL-2000Bifanoptionalmarinestylebatteryinweatherproofhousing
is used. Battery charge maintained by GTO Solar Panel Charger.
CONTROL
• Auto-memorizationofdigitaltransmittercode.Chargingregulatedbycircuitoncontrolboard.“Sleepdraw”is40
mA; “active draw” is 5 to 13 A.
• GTOremote-mountedRFreceivertunedto318MHz.
• Limitcontrolsaremechanical.Normallyopencontact.
• Adjustableauto-closetimer(OFF3to120s),inertia,andobstructionsensitivityusingthree(3)potentiometers.
• Powerterminalblockaccommodatesatransformerandsolarpanels.
• Operatorterminalblocksaccommodatesafetyedgesandphotoelectricsensorsforopeningandclosingmodes.
• Fullycompatibleaccessoryterminalblockprovidesconnectionsforsafetyloops,wands,intercoms,cardreaders,
phone systems, etc.
• AccessoryterminalblockfullycompatiblewithGTOpushbuttoncontrols,digitalkeypads,loopdetectors,etc.
• Controlboardallowsconnectionofsafetyedgesensorsandphotoelectricsensors.
• Audioentrapmentalarmsoundsifunitencountersanobstructiontwicewhileopeningorclosing.
OPERATIONAL CAPACITY
• TheSL-2000Bwillhandlegatesweighingupto1000lb.(453.4kg)andupto30ft.(9.14m)inlength(perleaf)if
the proper installation procedures have been followed. Note that ball bearing rollers and covers should be used
on all gates.
• TheSL-2000Bseriesoperatorsarecapableofhighvolumecycling;however,thetotalcyclesperdaywilldepend
on the motor current and eciency of the gate installation (see chart above). For questions relating to specic
applications and for information regarding cycling duty when charged by solar panels, call the GTO Service
Department at (800) 543-1236.These specications are subject to change without notice.
Cycles shown are for
single gate, dual gates will
get approximately half as
many cycles.
Rollers should be
lubricated at least four
times per year.
Housing Dimensions: Height: 18” Width: 211/2” Depth: 11”
SL-2000B Instruction Manual 04.26.12 3
SL-2000B PARTS IDENTIFICATION
(4) 3/8”-16 x 2” diameter U-Bolts
and (8) 3/8” Serrated Nuts (RB210)
(2) Quick Release Pins (211IH)
(2) Chain Master Links
(RB208)
(4) 1/4”-20 x 1/2” Screws
(RB226)
(2) Chain Brackets
(204IH)
Operator Housing
(A207)
32’ Drive Chain
(RB207)
18 Vac Transformer
120 Volt (RB570)
GTO Transmitter
(RB741)
Operator
Receiver
(AQ202-NB)
(2) 2” square x 48” long legs (206IH)
(4) 3/8” -16 x 3”
Carriage Bolts (RB659)
(4) 3/8”
Nuts
(RB668)
(4) 3/8”
Lock Washers
(RB641)
Control Box with
Control Board
and Battery
4 SL-2000B Instruction Manual 04.26.12
SINGLE GATE OPERATOR INSTALLATION
Gate Preperation
Overview of Operator Installation
Level
Plumb
Concrete
Concrete
Be sure the gate is properly installed and slides smoothly before installing the SL-2000B Slide Gate Operator.
The gate must be plumb, level, and move freely. The gate must not bind or drag on the ground. Never
use a wheel on the gate, because the additional drag and resistance can cause the operator to obstruct.
The diagram below shows a single slide gate installation with required safety features. The operator
must be installed on the inside of the gate. GTO requires using safety edges and roller guards to help
reduce the possibility of bodily injury.
Chain
Contact Sensor
Roller Guard
Receiver
(cable in separate
conduit)
Roller Guard
Contact Sensor
Contact Sensor
(REQUIRED)
(REQUIRED)
(REQUIRED)
(REQUIRED)
(REQUIRED)
Use PVC Conduit
(not included)
Run 1000' (max.) of low
voltage wire to control
box from transformer
(wire not included).
120 Volt Indoor
Transformer
(Surge Protector
not supplied)
Roller Guard
(REQUIRED)
Chain Bracket
Chain Bracket
for power cables.
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Operator
SL-2000B Instruction Manual 04.26.12 5
CAUTION
AUTOMATIC GATE
STAND CLEAR
1-800-543-GATE
®
Separate PVC Conduits
for power and control wiring.
Roller Guard
Roller Guard
Conduit through the concrete pad.
Separate PVC
Conduits for power
and control wiring.
Roller Guard
Roller Guard
Roller Guard
Conduit around the concrete pad.
CAUTION
AUTOMATIC GATE
STAND CLEAR
1-800-543-GATE
®
Operator
Operator
Roller Guard
RunthelowvoltagewireandreceiverwirethroughPVCconduitintothesliderunittoprotectitfrom
damage.PVCconduitshouldbeusedforaccessorywiressuchasloopdetectors,keypads,cardreaders
or any other entry device.
WARNING
WARNING
3/8"-16x3" Carriage Bolts
3/8" Lock Washers
& Nuts
48" x 2" sq. Legs
Step 1
Mount the legs on the slide gate
operator using the 3/8” x 3” Carriage
Bolts, 3/8” Flat Washers, 3/8” Lock
Washers, and 3/8” Nuts.
See Illustration A.
Illustration A
Recommended Wiring and Use of Conduit
Mounting the Legs on
the Gate Operator
6 SL-2000B Instruction Manual 04.26.12
Determining the Mounting Position and Mounting the Operator
Step 2
Install chain brackets at each end of the gate on the inside
(operator side) of the gate (see Overview Illustration, page.
4). Position the tops of chain brackets no more than 6” above
the bottom corners of the gate frame and secure with U-bolts
(see Illustration B). The chain brackets will work on gate
frames 1
3
/
4
” to 2
1
/
2
” in diameter or square tube gates. The
U-bolts provided will work on 2” diameter pipe. Larger gate
sizes will require larger U-bolts.
Step 4
Find the center point between the two roller/fence posts (see
Illustration D). This should coincide with the position of the
center point of the operator. Dig a hole approximately 12” x 28”
wide x 28” deep. Place the operator in the hole on its legs and
position the bottom idler sprockets on the top of the string and
level the unit (see Illustration E). Make sure operator is level and
plumb. With the unit level and in place, pour the concrete and
let set for 24 hours before proceeding to the next step.
BEFORE POURING CONCRETE: 1] Make sure operator is
centered between roller posts and aligned with string; and,
2]
Determine method of installing conduit for wiring (see page 5)!
Step 3
Insert a quick release
pin into the center slot
in each of the chain
brackets (see Illustration C). Tie a string to the end of each quick
release pin so that the string is tight between the two chain
brackets (the string will be used to align the operator). The string
should be 7”-10” from the ground (see Illustration B). The chain
brackets can be adjusted up or down on the gate to achieve the
proper height. The goal here is to set the height of the operator
so that when the housing is in place it will clear the ground by 1”
to 4” (see Illustration E).
Quick Release Pin
String
Chain Bracket
String
Chain Sprockets
Operator
(centered between post)
Roller
Gate
Fence Post
Fence Post
Center point between posts
Roller
C
L
Sprockets
String 7" to 10"
above ground
Housing
!
!
Level
1" to 4" clearance
Ground Level
position bracket so that string
will be approximately 7" to 10"
from ground level at the point where
the operator will be mounted
Quick Release Pin
String
Chain Bracket
Illustration B
Illustration C
Illustration D
Illustration E
SL-2000B Instruction Manual 04.26.12 7
Step 5
After the concrete has hardened, remove the
string from the quick release pins. Attach the
chain to one quick release pin with a master link
(see Illustration F). Run the chain through the
chain sprockets (see Illustration G).
Quick Release Pin
Chain
Master Link
Chain Bracket
Quick Release Pin
Chain
Master Link
Chain Bracket
Allow 1" of slack for every 10' of chain
Sprockets
Chain
Chain Bracket
• Fingers, hands, and
loose clothing may be
dragged into chain
sprockets.
• Fingers and hands can
be injured by rotating
sprockets.
• Keep hands, fingers,
and loose clothing
away from chain and
sprockets.
WARNING
!
WARNING
!
Chain Bracket
Gate
Step 6
Pull the chain to the second chain bracket.
(see Illustration G). Do not pull chain tight; a
tight chain will interfere with the operation of
the operator. Mark the chain where it meets
the second quick release pin.
Step 7
Drive the pin out of the chain link using
a tool such as a punch or chain break.
Connect the chain to the second quick
release pin using a master link (see
Illustration H).
Illustration F
Illustration G
Illustration H
TO OPEN THE GATE MANUALLY:
1. LIFT the quick release pins UP, then
PULL them OUT of the chain brackets
(see illustration).
2. Lay the chain down and manually slide
the gate to the desired position.
To prevent unauthorized removal of
the quick release pins, install pin locks
(see accessory catalog) above the quick
release pins in both chain brackets.
Installing the Chain
8 SL-2000B Instruction Manual 04.26.12
POWERING THE SYSTEM
Step 1
Make sure the control box power switch is in the
OFF position.
ON-OFF
OFF
Step 8
Unscrew and remove the front cover of the control box
and slide battery into position with its terminals to the
left (see illustration). Make sure the battery ts snugly in control box.
Connect the black battery lead to the negative (–) terminal, and the red battery lead to the positive (+)
terminal. DO NOT allow battery leads to touch the control board! Touching the control board with battery
leads can short circuit the system!
RED WIRE to positive (+)
BLACK WIRE to negative (–)
Connecting the Battery
Choose the electrical outlet into which the transformer will be plugged. Measure the distance from the
electrical outlet to the control box, following the path where the low voltage wire will run
(the maximum
distance can be no more than 1000 ft.).
Installation of the GTO Transformer
Step 3
Strip
3
/16” o the ends of the low voltage wire and attach ends to the
transformer terminals.
To prevent damage to transformer, make sure the exposed wire ends
do not touch each other!
NOTE: Wires coming from the ground to the control box should be run
throughPVCconduittoprotectthemfromdamage.
Feed the low voltage wires upward through the strain relief on the bottom
of the control box (see Illustration J).
Illustration I
Step 2
Run the low voltage wire from the electrical outlet to the control box. Do not exceed 1000 ft..
NOTE: Pull approximately 1 ft. of low voltage wire into the control box to accommodate terminal
connections. To maintain adequate charging power, use appropriate gauge, stranded, direct burial wire
(see Accessory Catalog).
RED
BLK
ORG
BLU
GRN
CLS EDG
OPN EDG
RED
GRN
ORG
BLU
WHT
BLK
ORG
BLU
GRN
CLS EDG
OPN EDG
LEARN
AUTO
CLOSE
INERTIA
BATT
+
–
OBSTRUCT
SENS.
RCVR
R
G
B
ALARM
SECOND OPERATOR
FIRST OPERATOR
POWER IN
18VAC SOLAR
~ ~ – +
ACCESSORY
PWR. SW.
Operator Power Cable
PVC Conduit
Low Voltage Wire
from AC Transformer
Illustration J
Step 4
Strip
3
/16” o the ends of the low voltage wire and twist tightly.
These wire ends will be attached to the control board at the
18VAC terminals located on the POWER IN terminal block (see
Illustration L). Wire sheathing should not come in contact with
terminals, however, it should not be stripped so far that wires can
come in contact with one another (see Illustration K).
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Mighty Mule MM-SL2000B-P User manual

Brand
Mighty Mule
Model
MM-SL2000B-P
Category
Gate Opener
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents