AOpen DUW160812X0502A User manual

Copyright

transcribed, stored in a retrieval system, or translated into any language or computer language, in

any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise, without the prior written permission of our company. All brand and product names are

trademarks and/or registered trademarks of their respective holders.

Disclaimer

We make no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties, merchantability or fitness for any

particular purpose. Any software described in this manual is sold or licensed “as is”. Should the

programs prove defective following their purchase, the buyer (and not our company., its

distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any

incidental or consequential damages resulting from any defect in the software. Further, we

reserve the right to revise this publication and to make changes from time to time in the contents

hereof without obligation to notify any person of such revision or changes.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a class B device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference in residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

y Reorient or relocate the receiving antenna.

y Increase the separation between the equipment and receiver.

y Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

y Consult the dealer or an experienced radio / TV technician help.

FCC Warning

Changes or modification not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

CLASS 1 LASER PRODUCT

APPAREIL A LASER DE CLASSE 1

LASER KLASSE 1

LOUKAN 1 LASERLAITE

PRODUIT LASER

CATEGORIE 1

Table of Contents

1. Use Precautions................................................................1

Warning for Safety...................................................................................1

Warning as to Use...................................................................................5

2. Introduction.......................................................................6

Overview .................................................................................................6

Features..................................................................................................7

Format Compatibility................................................................................8

Type of Writing Mode ..............................................................................9

Disc-At-Once...........................................................................................9

Track-At-Once.........................................................................................9

Session-At-Once.....................................................................................9

Multi-session...........................................................................................9

Packet Write............................................................................................9

3. Hardware Installaton ......................................................10

System Requirements...........................................................................10

Hardware Instruction .............................................................................11

3.2.1 Front Panel...................................................................................11

3.2.2 Rear Panel...................................................................................13

Installing the 16x DVD Dual drive..........................................................15

Required Tools......................................................................................15

Installation Procedure ...........................................................................15

DVD Region Coding..............................................................................20

Supported DVD±RW/±R, CD-R and CD-RW Media..............................21

Supported Media...................................................................................21

The handling of DVD±RW/±R, CD-R and CD-RW Discs......................22

4. Software Installation.......................................................23

Before You Start....................................................................................23

Installing Software.................................................................................23

Installing Nero 6 OEM Suite..................................................................23

Installing PowerDVD 5..........................................................................25

5. The Latest Features........................................................27

Auto Balance System (ABS):.................................................................27

Dynamic Damping System (DDS):........................................................27

Noise Control System (NCS):................................................................28

Buffer underrun Prevention (JustLink):..................................................28

Writing Speed Control (JustSpeed):......................................................29

Running Optimum Power Control (ROPC):...........................................29

Perfect Compatibility with blank media..................................................29

Chameleon Bezel..................................................................................30

Double Layer.........................................................................................30

Universal Bezel .....................................................................................30

6. Technical Support ..........................................................31

Firmware Upgrade.................................................................................31

Troubleshooting.....................................................................................31

Appendix A. Glossary...................................................................34

Appendix B. Frequently Asked Question (FAQ) ........................37

Use Precautions English

1. Use Precautions

These precautions explain how to use the device correctly and safely, thereby

preventing injury to you or to others. This section relates to your personal safety, and

also helps you minimize the risk of damaging the device. Please read carefully before

proceeding.

Warning for Safety

When you use this 16x DVD Dual, please pay heed to the following

At the time of installation:

As suggested in your

specifications please do not

install in an unstable

position or in one that

vibrates.

Do not install in high humidity,

direct sunlight, or damp

conditions.

Do not use near magnetic

fields, or place near a television

or a radio signal as the

performance of the device may

be affected.

Do not open to try to repair

as the laser may be harmful.

-- E-1 --

Use Precautions English

y Read these instructions carefully. Save these instructions for future reference.

y Follow all warnings and instructions marked on the product.

y Do not use this product near water.

y This product should be operated from the type of power indicated on the

marking label. If you are not sure of the type of power available, consult your

dealer or local power company.

y Never push objects of any kind into this product through cabinet slots as they

may touch dangerous voltage points or short out parts that could result in a fire

or electric shock. Never spill liquid of any kind on the product.

y Do not attempt to service this product yourself, as opening or removing covers

may expose you to dangerous voltage points or other risks. Refer all servicing

to qualified service personnel.

y Do not move from a cool environment to a warm one, as this will abruptly

change the temperature of the device

y When moving the device, remove any disc from the device because any harm

caused to the disc may result in data loss.

y Prevent liquids or metals from entering the device. If this situation should occur

please contact your reseller for advice.

y Do not use any evaporating solvents to clean the device. If a spray solvent

does happen to spray on the device please use a cloth to wipe it clean, or use a

neutral cleaner to dilute the solvent and wipe the device clean.

y When the device is reading/writing please do not interrupt power supply.

y Do not place damaged discs inside the device. In the winter do not use discs

brought in from outside immediately but wait until they have reached room

temperature.

y Unplug this product and refer servicing to qualified service personnel under the

following conditions:

a. When the power cord or plug is damaged or frayed

b. If liquid has been spilled into the product

c. If the product has been exposed to rain or water

d. If the product does not operate normally when the operating

instructions are followed. Adjust only those controls that are

covered by the operating instructions since improper adjustment of

other controls may result in damage and will often require

extensive work by a qualified technician to restore the product to

normal condition.

e. If the product has been dropped or the cabinet has been damaged

f. If the product exhibits a distinct change in performance, indicating

a need for service.

-- E-2 --

Use Precautions English

When installing the IDE device please pay attention to these

following details:

y Keep the IDE cable within 6 inches in length (15 cm).

y Before connecting the IDE cable, please make sure the power supply is off.

When cleaning CD / DVD disc, please note:

y Press the eject button to remove the disc

y Use compressed air to rid dust from the disc (spray with compressed air for

about five seconds)

-- E-3 --

Use Precautions English

y When checking for dust, please make sure that your hands do not touch the

surface of the disc.

Other points to pay attention to:

When moving the drive, please make sure that the disc has already been ejected.

y If you have not used the drive for some time, there will be dust collected on the

cover and in the tray. Before using the drive spray with compressed air to clean

it of dust.

y Before connecting all cables and wires, please make sure the power supply is

off otherwise this may cause a short circuit.

-- E-4 --

Use Precautions English

Warning as to Use

This 16x DVD Dual drive together with software is a product for utilizing 16x DVD

Dual recording media with rewriting, erasing and readout capabilities, as an internal

computer memory device. Except in the case where copying of

CD-ROMs/DVD-ROMs or the like is especially recognized under the copyrights laws

as being for the purpose of individual use by the customer or the like, or in the case

where the customer has obtained permission to make copies from the right holder,

reproduction of CD-ROMs/DVD-ROMs and copyright laws. Take notice that

unauthorized copying may be subject to claims for damages and to penalties.

DANGER

INVISIBLE / VISIBLE RADIATION

WHEN OPEN. AVOID EXPOSURE TO

BEAM.

-- E-5 --

Introduction English

2. Introduction

Overview

Thank you for purchasing this 16x DVD Dual drive. In this manual, we will explain how to

install your 16x DVD Dual drive correctly. Please read this manual carefully before using

the drive.

High Speed

This 16x DVD Dual drive offers unprecedented performance to handle today’s

demands by reading DVD’s at up to 16x speed and writing DVD+R(Single Layer)

discs at 12x speed. This product writes a DVD+R 4.7 GB disc in about 6 minutes.

Beside, this product writes CD-R or CD-RW discs at fast 48x / 32x speed. To read

CD’s up to 40x speed.

High Reliability

An improved anti-heat design and the OPC design boost recording reliability.

Optimum Power Control continually monitors signal levels during recording and

adjusts laser power to compensate for a dirty disc. This feature ensures a flat signal,

significantly enhancing reliability.

High Compatibility

This product supports all major CD / DVD formats, offering full backward-compatibility

through the huge installed base of CD-ROM/DVD-ROM drives and media. What’s

more, reordered DVD±RW/±R media can be played in a DVD player with multi-read

feature, maintaining future compatibility.

-- E-6 --

Introduction English

Features

y 8.5GB DVD+R DL (Double Layer) capacity

y UDMA Mode 4 (66MB/sec)

y 12x DVD+R writing speed

y Legacy DVD-ROM and DVD Player can play DVD±RW/±R disc

y Can read not only CD-R, CD-RW and DVD±RW/±R discs, but also video CDs,

music CDs, photo CDs, and CD-Text

y

JustLink technology prevents buffer underrun.

y JustSpeed technology for adaptive writing speeds.

y Excellent media compatibility: The firmware of 16x DVD Dual drive has tuned

up to the best compatibility.

y Running Optimum Power Control (ROPC) boosts recording reliability

y Versatile writing mode

y Disc breakage protection mechanism

y Extensive software bundled

y Emergency disk unload

y Automatic Tilt Calibration System (ATCS) for warped disc.

y Dynamic Damping System (DDS) to reduce vibration/noise

y An improved anti-heat design means that no cooling fan is needed.

y Compliant with Orange Book Part II (CD-R) and Part III, Volume 2 V1.0

(CD-RW)

y Back panel included analog audio output and digital audio output

-- E-7 --

Hardware Installaiton English

Format Compatibility

This 16x DVD Dual drive is compatible with the following formats:

”Read” means Data Transfer; “Play” means Audio Play back.

FORMAT Write Read Play*1

CD-DA

9

CD-ROM

9

CD-Extra

9

CD-ROM XA

9

Photo CD*2

9

CD-I*2

9

CD+G

9

CD-Text

9

DVD+RW/+R

9

DVD-RW/-R

9

DVD-ROM*3

9

DVD-Video

9

*1 Play means audio play back. Read means data transfer.

*2 CD-I, Photo-CD requires special reader/player. Photo-CD writing

requires Kodak license.

*3 Theoretically allows if disc being read is compatible with DVD-ROM

Not recommended and unwarranted by us be recorded onto a disk, it is

called “Disc-At-Once”.

-- E-8 --

Hardware Installaiton English

Type of Writing Mode

Disc-At-Once

When only a single recording session (lead in/data/lead out) is to be recorded onto a

disk, it is called “Disc-At-Once”.

When using Disc-At-Once, no additional data can be recorded onto the disc, even if

there is available capacity.

The advantage of this method recording is that it enables creation of discs that can be

played back on almost any CD player or CD-ROM drive, because there are no links

inserted between the data tracks.

Track-At-Once

When many sessions are to be recorded onto a disc, it is called “Track-At-Once”. If

there is space available on the disc, additional data can be recorded onto it.

The advantages of this method include being able to record additional sessions onto

a disc, and using a CD-ROM of backup data. (Refer to “Multi-session”.)

Session-At-Once

A "Session-at-Once" recording almost corresponds to a "Disc-at-Once recording", i.e.

all data ("Lead-in", data area and "Lead-out" are written in one go.

The only difference is that the CD is not "finished", i.e. after a "Session-at-Once"

recording you still have the possibility to write a further "Session" on the CD at a later

date.

Multi-session

The recording of lead-in/data/lead-out is referred to as one session. The

Disc-At-Once method is also referred to as “Single Session”, because the disc is only

recorded once. A disc that has had multiple additional session recorded onto it using

the Track-At-Once method is called “Multi-session”.

Packet Write

The Packet Write recording method was developed. It differs from Track-At-Once or

Disc-At-Once in that data is recorded in small fixed sectors of 64k bytes, known as

packets.

The advantages of this method are elimination in overhead per session and the

elimination of buffer under run errors. This method, however, cannot be utilized for

audio data. A number of formats, such as UDF and CD-R FS, can be used when

recording using the Packet Write method.

*

-- E-9 --

Hardware Installaiton English

3. Hardware Installaton

The installation of this product is fast and easy. Please follow these instructions

described below:

System Requirements

A PC system with the following features is highly recommended for ensuring a stable

16x DVD Dual performance.

CPU We suggest using a Pentium!!! 450MHz

or above (JustLink in use)

Memory 64MB or above

System

requirements

Operating

systems

Windows 98SE, Windows 2000,

WindowsXP, Windows Me,

Interface Compatible with Enhanced IDE, and Blank Primary

Slave, Secondary Master, and Secondary Slave

Hard disc Average saving time is 19ms or lower, max data transfer

speed is 33.3MB/sec; disc space 500MB or over

Voltage +12V or +5V voltage switches

*CD-RW discs: perhaps are unable to be read in the CD-ROM. If this situation

comes about it is likely that your CD-ROM is not compatible with multi-read please

change to a Multi-read compatible CD-ROM or use your 16x DVD Dual.

*All Multi-read CD-ROM devices have the following features

(1) CD-ROM is able to read data created by optical heads

(2) CD-ROM will support the UDF specification (Packet Writing)

-- E-10 --

Hardware Installaiton English

Hardware Instruction

3.2.1 Front Panel

1. Disc Tray

2. Indicator

3. Eject Button

4. Emergency Eject Hole

Don’t use force to pull out or push in the disc tray. This might cause

damage to the loading section of the drive.

Name Features

Disc Tray This tray is for loading the CD disc. It will accept

120mm and 80mm discs. Please place the disc in the

exact center of the tray

Indicator When a disc has been ejected or is being saved the

display light will shine. When a disc is being burnt, or a

disc cannot be saved the display light will go out. When

a disc is unable to be read, or the device is being

repaired the display light will flash.

Emergency Eject Hole When the power supply has been interrupted or it is

impossible to eject a disc please use a pin to press the

emergency eject hole so that the tray will eject the disc.

-- E-11 --

Hardware Installaiton English

Eject Button Pressing this controls the insertion and ejection of the

tray.

Emergency Eject Hole

This function is only for emergency case. Do not use this

function in usual case to prevent from mechanical damage.

-- E-12 --

Hardware Installaiton English

3.2.2 Rear Panel

1. Audio Output Connector

2. Device Configuration Jumper

3. IDE Connector

4. Power Connector

Name Features

Audio Output

Connector

Is able to be connected to a sound card audio

input and can use a sound card to listen to a CD

music

Device

Configuration

Jumper

Used when selecting the device configuration of

E-IDE. Don’t use jumpers to change anything

besides the device configuration. Configuration

changes become valid after power is turned off,

then on again. The device configuration jumper

will be set to Master as factory default setting

E-IDE Connector Use a two-headed 40pin IDE cable and an IDE

connector head. Before connecting please switch

off the power supply

Power Connector Connect DC 5V/12V to the power connector

Be careful not to reverse the power connector when attaching it. A

reversed connection may cause damage to the equipment (not

covered by the warranty)

Connecting or disconnecting E-IDE connectors while power is on

may result in a short circuit, causing damage to the equipment.

When connecting or disconnecting connectors, make sure to turn off

the power beforehand.

-- E-13 --

Hardware Installaiton English

There is another very important thing to take care of before the installation of the

16x DVD Dual drive is setting the master/slave jumpers. Please examine the panel

at the rear of the machine in order to set the master/slave jumpers.

MASTER

SLAVE

Please do not use USE

CSEL setting

USE CSEL

-- E-14 --

Hardware Installaiton English

Before plugging in the jumpers please make sure you have switched

off the power supply of both the 16x DVD Dual and the computer.

Please make sure the jumpers are inserted as displayed in the

diagram otherwise you may cause irreparable damage to your 16x

DVD Dual device

Note: Installing jumper pins besides the ones for device configuration

settings may be the cause of damage or abnormal drive operation.

Installing the 16x DVD Dual drive

Firstly, power off your computer and all peripheral devices. Unplug the computer’s

power cord from wall outlet or from the power strip.

Required Tools

y A medium-size screwdriver

y A long-nosed pliers

y Your computer system or motherboard manual (to locate your computer

system’s IDE controller).

Installation Procedure

The discharge of static electricity can damage electronic circuitry. You can

avoid static discharge by touching a grounded metal object, like your

computer case, before and during installation of hardware inside your

computer.

-- E-15 --

Hardware Installaiton English

1. Remove the housing or casing of your computer. Be careful of any sharp edges,

which might be hidden inside your computer.

2. If there is not any other CD-ROM drive installed in your system.

We recommend installing the 16x DVD Dual in the Secondary IDE port. It is

unnecessary to adjust any other jumpers on the 16x DVD Dual. Proceed to step 4

for further installation.

3. If a CD-ROM drive is already installed in your system.

We recommend that you install the CD-ROM on the Secondary IDE

channel as the master device (MA), and the 16x DVD Dual on the

Secondary IDE channel as the slave device (SL). Please follow the steps

below to fulfill this arrangement.

y First make sure that your Secondary IDE cable has two ports available for two

IDE devices. If not, ask your main board vendor or purchase one from computer

hardware stores.

y If the CD-ROM drive was installed in the Primary IDE channel, disconnect it

from the Primary IDE cable.

y Adjust the Device Configuration Jumper of the CD-ROM drive to “Master” (MA)

position.

y Adjust the Device Configuration Jumper of the 16x DVD Dual to “Slave” (SL)

position.

-- E-16 --

Hardware Installaiton English

4. First remove the 5.25-inch panel. Further detail of how to remove this can be

found in your computer manual.

5. Place the 16x DVD Dual into the slot. Do not force it in any further than need be

due to the connector cables.

6. Use four provided screws (size: M3x0.5x4mm) to secure the drive into the

half-height bay. The screws electronically ground the drive.

This 16x DVD Dual drive can be horizontally/vertically installed and

operated.

-- E-17 --

Page is loading ...

AOpen DUW160812X0502A User manual

This manual is also suitable for

AOpen DUW160812X0502A User manual

Related papers

Other documents