GE CV48SSL1SS User manual

Brand: GE

Model: CV48SSL1SS

Category: Cooker hoods

Type: User manual

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on a label on

the front panel of the unit.

ESPAÑOL

Para consultar una version en

español de este manual de

instrucciones, visite nuestro sitio de

internet GEAppliances.com.

VENT HOOD

Stainless Steel Professional

49-80819 11-17 GEA

SAFETY INFORMATION ...........3

USING THE HOOD

Controls ................................5

Implement Holders .......................5

For your Safety ..........................5

CARE AND CLEANING

Baffle Grease Filters and Drip Trays ........6

Stainless Steel Surfaces. . . . . . . . . . . . . . . . . . . 7

Light Bulbs .............................7

INSTALLATION INSTRUCTIONS ..8

TROUBLESHOOTING TIPS ........20

WARRANTY ........................22

ACCESSORIES .....................23

CONSUMER SUPPORT ............24

CV48S

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

GE is a trademark of the General Electric Company. Manufactured under trademark license.

2 49-80819

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-80819 3

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

B. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting

means to prevent power from being switched

on accidentally. When the service disconnecting

means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the

service panel.

C. Do not use this unit with any solid-state speed

control device.

D. This unit must be grounded.

CAUTION

FOR GENERAL VENTILATING USE

ONLY. DO NOT USE TO EXHAUST HAZARDOUS

OR EXPLOSIVE MATERIALS AND VAPORS.

CAUTION

To reduce risk of fire and to properly

exhaust air, be sure to duct air outside. Do not vent

exhaust air into spaces within walls or ceilings or into

attics, crawl spaces, or garages.

WARNING

TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING*:

A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do

not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN—You may be

burned.

C. DO NOT USE WATER, including wet dishcloths or

towels—a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher,

and you already know how to operate it.

2. The fire is small and contained in the area where

it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by

NFPA.

WARNING

TO REDUCE THE RISK OF A

RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high

settings. Boil overs cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or

medium settings.

B. Always turn hood ON when cooking on high heat or

when flambéing food (i.e. Crepes Suzette, Cherries

Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware

appropriate for the size of the surface element.

4 49-80819

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

READ AND SAVE THESE INSTRUCTIONS

How to Remove Protective Shipping Film and Packaging Tape

Carefully grasp a corner of the protective shipping film

with your fingers and slowly peel it from the appliance

surface. Do not use any sharp items to remove the film.

Remove all of the film before using the appliance for the

first time.

To assure no damage is done to the finish of the

product, the safest way to remove the adhesive from

packaging tape on new appliances is an application of

a household liquid dishwashing detergent. Apply with a

soft cloth and allow to soak.

NOTE: The adhesive must be removed from all parts.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with all

applicable codes and standards, including fire-rated

construction.

B. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer’s

guidelines and safety standards such as those

published by the National Fire Protection

Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE) and the local code authorities.

When applicable, install any makeup (replacement)

air system in accordance with local building code

requirements. Visit GEAppliances.com for available

makeup air solutions.

C. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

D. Ducted fans must always be vented to the outdoors.

E. Turn off breaker to adjacent rooms while working.

WARNING

TO REDUCE THE RISK OF FIRE,

USE ONLY METAL DUCTWORK.

Do not attempt to repair or replace any part of your hood

unless it is specifically recommended in this manual.

All other servicing should be referred to a qualified

technician.

49-80819 5

1. Light control: Turn the light control from OFF

to HI for the brightest light while cooking.

2. Fan control: Turn the fan control speed from

OFF to HI as needed.

Continuous use of the fan system while cooking

helps keep the kitchen comfortable and less humid.

It also reduces cooking odors and soiling moisture

that create a frequent need for cleaning.

NOTE: When the fan is operating on the lowest

setting, it will be very quiet. Always make sure that

the fan is turned OFF when you are finished in the

kitchen.

Controls

USING THE HOOD: Controls / Implement Holders / For your Safety

Appearance will vary.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag, to the service panel.

For your Safety

6 49-80819

Some models have reusable metal grease baffles and

drip trays.

The metal baffles channel grease released by foods

on the cooktop into the drip trays. The baffles also help

prevent flaming foods on the cooktop from damaging the

inside of the hood.

For this reason, the baffles must ALWAYS be in place

when the hood is used. The grease baffles and drip trays

should be cleaned once a month, or as needed.

To clean the grease baffles and drip trays, drain and

wipe all excess grease with a dry paper towel. Soak

them and then swish them around in hot water and

detergent. Don’t use ammonia or ammonia products

because they will darken the metal. Do not use abrasives

or oven cleaners. Rinse, shake and let them dry before

replacing. They may also be cleaned in an automatic

dishwasher.

To remove:

Grasp the baffle knobs and pull them up, forward and

out. Grasp the drip tray and carefully lift it up and out of

the hood track.

To replace the drip trays:

1. Place and seat the drip tray into the hood track.

2. Slide them left or right until all trays are side-by-side

in place in the track.

To replace the baffles:

1. Hold the baffle at the bottom by one of the knobs .

2. Place the other end of the baffle against the inside

front of the hood.

3. Slide it up and push the bottom end back until it firmly

seats into place.

To clean behind the knobs:

If the knobs are difficult to remove, place a non-abrasive

cloth between the knob gap and hood body to assist with

pulling the knobs off for cleaning.

Baffle Grease Filters and Drip Trays (on some models)

CARE AND CLEANING: Baffle Grease Filters and Drip Trays

Drip Tray Replacement

Drip Tray

Track

Baffle

Baffle Replacement

49-80819 7

Do not use a steel wool pad; it will scratch the surface.

To clean the stainless steel surface, use warm sudsy

water or a stainless steel cleaner or polish. Always wipe

the surface in the direction of the grain. Follow the cleaner

instructions for cleaning the stainless steel surface.

To inquire about purchasing stainless steel appliance

cleaner or polish, or to find the location of a dealer

nearest you, please call our toll-free number:

National Parts Center 1.800.626.2002

GEApplianceParts.com

To change the light bulbs:

1. Grasp the outer trim ring and twist until reaching the

unlock position. Then pull the ring straight out.

2. Grasp the bulb and twist until reaching the unlock

position. Then gently pull the bulb straight out.

3. Replace with the same wattage, type and size bulb.

Wear gloves. Do not touch bulb with your bare

fingers.

These 120 volt, 50 watt halogen bulbs with a GU10

base are available at specialty lighting stores and

home building centers.

Order bulb no. WB08X10052.

4. Replace the outer trim ring by inserting the two

retaining tabs into the two tab slots, pressing the ring

flush with the surface of the hood insert and twisting

until reaching the lock position.

Stainless Steel Surfaces (on some models)

Light Bulbs

CARE AND CLEANING: Stainless Steel Surfaces / Light Bulbs

8 49-80819

Installation

Instructions

“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)

or visit our website at: GEAppliances.com”

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

Ŷ

IMPORTANT — Save these

instructions for local inspector’s use.

Ŷ

IMPORTANT — Observe all governing

codes and ordinances.

Ŷ Note to Installer – Be sure to leave these

instructions with the Consumer.

Ŷ Note to Consumer – Keep these instructions for

future reference.

Ŷ Skill level – Installation of this vent hood requires

basic mechanical and electrical skills.

Ŷ Completion time – Approximately 1 to 3 hours

Ŷ 3URSHULQVWDOODWLRQLVWKHUHVSRQVLELOLW\RIWKH

installer.

Ŷ 3URGXFWIDLOXUHGXHWRLPSURSHULQVWDOODWLRQLVQRW

covered under the Warranty.

FOR YOUR SAFETY

WARNING

Before beginning the installation,

switch power off at service panel and lock the

service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag,

to the service panel.

CAUTION

Due to the weight and size of

these vent hoods and to reduce the risk of personal

injury or damage to the product, TWO PEOPLE

ARE REQUIRED FOR PROPER INSTALLATION.

WARNING

Disconnect all electrical power

at the main circuit breaker or fuse box before

installing.

Professional Vent Hood

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with

all applicable codes and standards, including

fire-rated construction.

B. Sufficient air is needed for proper combustion

and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment

manufacturer’s guidelines and safety standards

such as those published by the National Fire

Protection Association (NFPA), the American

Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE) and the local

code authorities.

C. When cutting or drilling into wall or ceiling, do

not damage electrical wiring and other hidden

utilities.

D. Ducted fans must always be vented to the

outdoors.

E. Turn off breaker to adjacent rooms while

working.

WARNING

TO REDUCE THE RISK OF FIRE,

USE ONLY METAL DUCT WORK.

49-80819 9

PRODUCT DIMENSIONS

Model CV48S With Straight Sides

HARDWARE PACKAGE

Locate and check contents.

Screws shown actual size.

PARTS PROVIDED

Locate the parts packed with the hood.

INSTALLATION PREPARATION

2 Knobs

2 Stainless Steel Grease Filters

(3 filters with 48" models)

Wood Support

with Original Screws

2 Grease Filter Trays

(3 supports with 48" models.)

2 (3/16") hollow wall anchors

with screws to secure hood to

the wall at the bottom

2 flat washers for

wall anchors

6 Phillips head screws

to secure hood to

the wood support:

(2 secured to wood

support)

6 screws to secure the wood

support and the hood to the wall

Installation Preparation

12"

47 15/16"

47 15/16"25"

18"

10 49-80819

INSTALLATION PREPARATION

Installation Preparation

TOOLS AND MATERIALS

REQUIRED

(NOT SUPPLIED)

CAUTION

Lift the hood by grasping the

outside edges of the inlet opening of the hood. Do

not lift the hood by grasping the exhaust opening or

transition duct with damper!

Ŷ 2SHQWKHFDUWRQDQGUHPRYHWKHKRRGDQG

packaging.

Ŷ &RQILUPWKDWDOOKDUGZDUHDQGSDUWVDUHSUHVHQW

by reviewing the section named Parts Provided in

the Installation Instructions.

Ŷ /RRVHQWKHVFUHZVKROGLQJWKHZRRGVXSSRUWWR

the back of the hood. Remove wood support.

Keep wood support and screws. These will be

used to mount the hood to the wall.

Ŷ )XOO\LQVSHFWDQGFRQILUPWKDWDOOWDSHDQG

packing material has been removed from the

hood and transition duct with damper

Pliers

Wire Cutter/Stripper

Tin Snips

Spirit level

Duct tape

Safety glasses

Ladder

Saber saw or Key Hole Saw

Phillips and Flat blade

screwdrivers

1/4” pivoting hex socket

Hammer

Electric drill with 1/8” and 3/8” bits

Flashlight

UL Listed Wire nuts

Pencil and tape

measure

120V 60Hz. 15 or 20 Amp,

2-wire with ground. Properly

grounded branch circuit.

Strain relief for

junction cover.

10" round metal duct,

length to suit installation

Top view of open shipping carton

Do not lift from

transition duct Hood

Lift hood out of carton

from the sides

Carton

49-80819 11

Installation Preparation

INSTALLATION PREPARATION

INSTALLATION CLEARANCES

These vent hoods are designed to be installed onto

a wall or beneath a soffit or cabinet.

Ŷ ,QVWDOOWKHVHKRRGV0LQWR0D[DERYH

the cooking surface.

NOTE: Clearances may vary due to type of

cooking product and local codes. Check with

local inspectors to be sure standard is applicable.

In this installation the ductwork running from the top

of the hood will be concealed in the soffit or upper

cabinetry.

For this installation, a decorative duct cover is

available to conceal the ductwork running from the

top of the hood. Use of the duct cover requires

special consideration to the installation height

above the countertop.

OPTIONAL DUCT COVER

ACCESSORIES

Standard decorative duct covers are available in

6" and 12" heights. Duct covers may be stacked,

in various combinations, to conceal the ductwork

running from the top of the hood to the ceiling.

Ŷ %HIRUH\RXEHJLQ\RXVKRXOGGHWHUPLQHWKH

installation height of the hood and order the

correct size duct cover. The duct covers should

be ordered at the same time as the vent hood

and be on site before installation. Order the duct

cover corresponding to your model.

6” Duct Covers

Hood

Model

6” Duct

Cover Dimensions

CV48S UX48DC6J 6”H x 19-11/16”W x 11-7/8”D

12” Duct Covers

Hood

Model

12” Duct

Cover Dimensions

CV48S UX48DC12J 12”H x 19-11/16”W x 11-7/8”D

OPTIONAL SERVICE PART

RANGE HOOD UTENSIL HOLDER

A utensil rack part # WB02X25909 is available as a

service part for this hood.

Visit GEApplianceParts.com for more details.

Wall Mount Installation

30" MIN.

36" MAX.

SOFFIT

Soffit Installation

30" MIN.

36" MAX.

6" Duct Cover

12" Duct Cover

Standard Duct Covers

12 49-80819

DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES

These vent hoods must be installed 30” min. to 36”

max. above the standard 36” high cooking surface

when installed over any professional style rangetop or

range. The exact hood installation height is determined

by the ceiling height.

1. Measure the exact ceiling height.

2. Review the chart at right to determine the range

of possible hood installation heights that can be

accomplished with one or more duct covers.

3. Increase or decrease hood installation height to

accommodate the fixed 6" or 12" duct covers and

use a whole number of duct covers, otherwise cutting

and modifying one duct cover may be required.

4. Duct covers may be stacked, in various

combinations, to reach ceiling heights.

Straight or Taper-Sided Hoods

NOTE: Minimum ceiling height for REAR WALL

EXHAUST with duct covers is 8'4" when installing at

30" above countertop using 10" elbow.

*Based on 36" countertop height.

NOTE: Additional duct covers may be used to reach

higher ceilings.

INSTALLATION PREPARATION

Installation Preparation

Actual

Ceiling

Height

*Possible

Hood

Installation

Height

6" Duct

Covers

12" Duct

Covers

7' 11" 35" 1

8' 0"

30"

36" 1

8' 1" 31" 1

8' 2" 32" 1

8' 4" 33" 1

8' 4" 34" 1

8' 5" 35" 1

8' 6"

30"

36"

8' 7" 31" 1 1

8' 8" 32" 1 1

8' 9" 33" 1 1

8' 10" 34" 1 1

8' 11" 35" 1 1

9' 0"

30"

36" 1

9' 1" 31" 2

9' 2" 32" 2

9' 3" 33" 2

9' 4" 34" 2

9' 5" 35" 2

9' 6"

30"

36" 1

9' 7" 31" 1 2

9' 8" 32" 1 2

9' 9" 33" 1 2

9' 10" 34" 1 2

9' 11" 35" 1 2

10' 0"

30"

36" 1

10' 1" 31" 3

10' 2" 32" 3

10' 3" 33" 3

10' 4" 34" 3

Installation Height

Ceiling Height

to Floor

Duct Covers

18" Hood

Height

49-80819 13

Installation Preparation

INSTALLATION PREPARATION

ADVANCE PLANNING

Duct Install Planning

Ŷ 7KHVHYHQWKRRGVDUHHTXLSSHGIRU´URXQG

ductwork. For best performance, use 10” round

ductwork on the 48” wide hoods.

Ŷ 7KLVKRRGPD\EHYHQWHGYHUWLFDOO\WKURXJKXSSHU

cabinets, soffit or ceiling. A duct transition piece is

supplied for vertical exhaust. Use locally supplied

elbows to vent horizontally through the rear wall.

Ŷ 8VHPHWDOGXFWZRUNRQO\

Ŷ 'HWHUPLQHWKHH[DFWORFDWLRQRIWKHYHQWKRRG

Ŷ 3ODQWKHURXWHIRUYHQWLQJH[KDXVWWRWKH

outdoors. To maximize the ventilation

performance of the vent system:

1. Minimize the duct run length and number of

transitions and elbows.

2. Maintain a constant duct size.

3. Seal all joints with duct tape to prevent any

leaks.

4. Do not use any type of flexible ducting.

Ŷ 8VHWKHVKRUWHVWDQGVWUDLJKWHVWGXFWURXWH

possible.

Ŷ ,QVWDOODZDOOFDSRUURRIFDSZLWKGDPSHUDWWKH

exterior opening. Order the wall or roof cap and

any transition needed in advance.

Ŷ :KHQDSSOLFDEOHLQVWDOODQ\PDNHXS

(replacement) air system in accordance

with local building code requirements. Visit

GEAppliances.com for available makeup air

solutions.

Wall Framing for Adequate Support

Ŷ 7KLVYHQWKRRGLVKHDY\$GHTXDWHVWUXFWXUDO

support must be provided. The hood must be

secured to vertical studs in the wall. See page 14.

Ŷ :HVWURQJO\UHFRPPHQGWKDWWKHYHQWKRRGZLWK

duct cover be on site before final framing and

wall finishing. This will also help to accurately

locate the ductwork and electrical service.

Decorative Duct Covers:

Decorative duct covers, 6" and 12" high, are

available to fit all models. The duct cover conceals

the ductwork running from the top of the hood to the

ceiling or soffit. Stack one or more duct covers over

the top of the hood to reach your ceiling height.

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING

FOR PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before

beginning installation.

Do not use an extension cord or adapter plug with

this appliance. Follow National Electrical Codes or

prevailing local codes and ordinances.

Electrical supply

These vent hoods must be supplied with 120V,

60Hz, and connected to an individual, properly

grounded branch circuit, and protected by a 15 or

20 amp circuit breaker or time delay fuse.

Ŷ :LULQJPXVWEHZLUHZLWKJURXQG

Ŷ ,IWKHHOHFWULFDOVXSSO\GRHVQRWPHHWWKHDERYH

requirements, call a licensed electrician before

proceeding.

Ŷ 5RXWHKRXVHZLULQJDVFORVHWRWKHLQVWDOODWLRQ

location as possible in the ceiling or wall.

Ŷ &RQQHFWWKHZLULQJWRWKHKRXVHZLULQJLQ

accordance with local codes.

Grounding instructions

The grounding conductor must be connected to

a ground metal, permanent wiring system, or an

equipment-grounding terminal or lead on the hood.

WARNING

The improper connection of the

equipment-grounding conductor can result in a risk

of electric shock. Check with a qualified electrician

or service representative if you are in doubt whether

the appliance is properly grounded.

14 49-80819

INSTALLATION PREPARATION

Installation Instructions

DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS

Ŷ 8VHDOHYHOWRGUDZWKHFRRNWRSFHQWHUOLQHORFDWLRQ

Draw the line to ceiling height.

Ŷ 0HDVXUHGHVLUHGGLVWDQFHIURPWKHERWWRPRIWKH

hood to the cooking surface, 30" min. to 36" max.

NOTE: If you are installing the hood with duct covers,

be sure to read “Using Duct Cover Accessories” page

7. Exact installation height may be determined by use

of one or more duct covers.

Ŷ 8VHDOHYHOWRGUDZDVWUDLJKWKRUL]RQWDOSHQFLOOLQH

indicating the bottom of the hood.

Ŷ )URPWKHOLQHLQGLFDWLQJWKHERWWRPRIWKHKRRG

measure 15-3/8" up and draw another line for the

location of the wood support. See illustration.

FOR VERTICAL (Straight Up) DUCTING:

Ŷ 8VHDOHYHOWRGUDZDFHQWHUOLQHIURPWKHERWWRPRI

the hood to ceiling or soffit.

Ŷ ,IYHQWLQJRXWWKHFHLOLQJH[WHQGWKHFHQWHUOLQH

forward on the ceiling or soffit.

Ŷ /RFDWHWKHFHQWHUOLQHRIDKROHRQWKHFHLOLQJ

or soffit by measuring 6" from the wall.

FOR DUCTING THROUGH REAR WALL:

Ŷ 0HDVXUHDERYHWKHPDUNHGOLQHIRUWKHWRS

of the hood. At the centerline, mark location for a

10-1/2" diameter hole.

NOTE: Minimun ceiling height for REAR WALL

EXHAUST with duct covers is 8'4" when installing at

30" above countertop using 10" elbow

House Wiring Location:

Ŷ 7KHMXQFWLRQER[LVIDVWHQHGWRWKHEDFNRIWKHKRRG

on the right side.

Ŷ 7KHUHFHVVHGEDFNVLGHRIWKHKRRGSURYLGHVD

large area for the house wiring to exit the wall and

be routed to the rear knockout and junction box.

Ŷ 5HPRYHMXQFWLRQER[FRYHUDQGNQRFNRXW,QVWDOO

strain relief.

Alternate Knockout Locations

If the installation requires, the junction box can

be relocated from the back to the top of the hood.

Remove 3 screws, align box to top knockout and

secure with original screws.

Ŷ 5HPRYHMXQFWLRQER[FRYHUDQGNQRFNRXW,QVWDOO

strain relief.

18-13/16" for 48" Models

12-13/16" for 36" Models

9-13/16" for 30" Models

Electrical

Area

8-3/8"

6-1/2"

18-1/16" for 48" Models

12-1/16" for 36" Models

9-1/16" for 30" Models

Bottom of Hood

Wood

Support

Top of Hood

15-3/8"

18"

9-7/8"

49-80819 15

Installation Instructions

INSTALLATION PREPARATION

INSTALL HOOD ONTO WALL

SKIP THIS STEP IF INSTALLING BENEATH A

SOFFIT OR CABINET, GO TO STEP 2B.

Ŷ /RFDWHDWOHDVWYHUWLFDOVWXGVDWWKHZRRGVXSSRUW

Ŷ )RU´PRGHOVLIYHUWLFDOVWXGVFDQQRWEHORFDWHG

then install 2 screws through the wood support into

the stud that is located, vertically aligned with the

screws located ½” from the edge of the wood support.

Ŷ &HQWHUWKHVXSSOLHGZRRGVXSSRUWOHIWWRULJKWDQG

below the 15-3/8" marked line.

Ŷ 6HFXUHWKHZRRGVXSSRUWWRRUPRUHYHUWLFDOVWXGV

using at least 2 of the 4 supplied long screws. For the

30” model, you may need to add framing to existing

framing to secure the wood support to 2 studs.

IMPORTANT: Screws must penetrate at least 1” into

vertical studs. Countersink screws into support.

NOTE: The mounting screws

must remain in their original

shipping location. These

screws are positioned

to engage the

keyhole slots in

the back of the

hood.

Ŷ Adjust depth of original mounting screws in the

wood support until they protrude 1/4" forward. This

1/4" gap will provide clearance to hang the hood.

IMPORTANT: Framing must be capable of

supporting up to 150 lbs.

Ŷ 8VHGXFWWDSHWRVHDOWKHWUDQVLWLRQGXFWFRQQHFWLRQ

Check to be sure the damper moves freely.

Hang Hood On Wood Support

Ŷ /LIWWKHKRRGDQGKROGFORVHWRWKHLQVWDOODWLRQ

location. Route house wiring through the knockout

and into the junction box.

Ŷ 3ODFHWKHKRRGRYHUWKHZRRGVXSSRUW%HVXUHWKH

mounting screws engage the keyhole slots in the

back of the hood. Tighten the screws.

Ŷ ,QVWDOODGGLWLRQDOVFUHZVWRVHFXUHWKHKRRGWRWKH

wood support.

Ŷ 'ULOO´SLORWKROHVLQWRWKHWZRORZHUKROHV,IWKH

pilot hole enters a stud, use a washer and the long

wood screw. If the pilot hole does not enter a stud,

enlarge the hole to 3/8” to accept the wall anchor, and

use a washer and the screw from the wall anchor.

Centerline of

Installation

Space

15-3/8"

30"

36"

Wood

Support

1/4"

Gap

Original Mounting

Screws as Shipped

Centerline of

Installation

Space

30"

36"

16 49-80819

INSTALLATION PREPARATION

Installation Instructions

Alternate Mounting Method

INSTALL HOOD TO SOFFIT OR BENEATH CABINETS

SKIP THIS STEP IF USING WALL MOUNTING

METHOD

When necessary, the hood may be installed so that it

is supported by the soffit.

Ŷ 7KHVRIILWVKRXOGEHFRQVWUXFWHGZLWK[¶V

Ŷ 'HWHUPLQHWKHLQVWDOODWLRQORFDWLRQRQWKHZDOO

Ŷ &RQWLQXHWKHFHQWHUOLQHIRUZDUGRQWKHERWWRPRIWKH

cabinet or soffit.

Ŷ 7KHRSHQLQJDERYHWKHKRRGVKRXOGDOORZIRUWKH

10" round duct and clearance to slide the hood back

against the wall.

Ŷ 7KH[VWXGVPXVWEHORFDWHGDVVKRZQLQWKH

chart, Dim. A. to accept mounting screws.

“A” Centerline to Stud

and Keyhole Slots

“B” Hood Width At

the Top

CV48S 23-9/16" 47-15/16"

Ŷ 'ULOOSLORWKROHVLQWRWKHVWXGVDWWKHORFDWLRQV

shown in the top view illustration.

IMPORTANT: Soffit framing must be capable of

supporting up to 150 lbs.

Ŷ 8VHGXFWWDSHWRVHDOWKHWUDQVLWLRQGXFWFRQQHFWLRQ

Check to be sure the damper moves freely.

Mount Hood onto Soffit or Cabinet

NOTE: If mounting to the underside of a cabinet with a

recessed bottom, install shims to fill the gap.

Ŷ 'ULYHPRXQWLQJVFUHZVLQWRWKHVWXGVXQWLOWKH\

protrude 1/4". The 1/4" gap will provide clearance to

engage the keyhole slots in the top of the hood.

Ŷ /LIWKRRGWRLQVWDOODWLRQSRVLWLRQ/RFDWHKRXVHZLULQJ

and route through the knockout (from the back or

top of the hood).

Ŷ /LIWKRRGRQWRPRXQWLQJVFUHZV6OLGHEDFNDJDLQVW

the rear wall.

Ŷ 7LJKWHQPRXQWLQJVFUHZV

IMPORTANT: For additional support and to

minimize vibration during operation, the hood must

be secured to the back wall. Use wall anchors to

fasten bottom back of hood to the wall.

Requires 10-1/2" Min.

Opening For Ductwork

and Hood Installation

7-1/2"

2-9/16"

10"

3/4"

Back of Hood

Top View

Front of Hood

1/4" Gap

Push Back

to Wall

Add Shims

If Bottom

Is Recessed

Back

Wall

Cabinet

Soffit

Engage Top

Keyhole Slots

49-80819 17

Installation Instructions

INSTALLATION PREPARATION

CONNECT DUCTWORK

Ŷ ,QVWDOOGXFWZRUNPDNLQJFRQQHFWLRQVLQGLUHFWLRQ

of airflow as illustrated.

Ŷ 6HFXUHMRLQWVLQGXFWZRUNZLWKVKHHWPHWDOVFUHZV

Ŷ :UDSDOOGXFWMRLQWVZLWKGXFWWDSHIRUDQDLUWLJKW

seal.

Ŷ 8VHGXFWWDSHWRVHDOWKHIODQJHFRQQHFWLRQ

Reach inside the hood and push the damper up

to be sure it moves freely.

INSTALL DUCT COVERS

NOTE: For easier handling, remove cardboard

insert after film is peeled off.

Remove protective film from duct covers. If more

than one duct cover is used, secure each piece

together with screws provided.

Ŷ 3ODFHWKHGXFWFRYHUVRQWRSRIWKHKRRG

Ŷ )URPLQVLGHWKHKRRGVHFXUHWKHGXFWFRYHU

to the top with the small Phillips head screws

supplied with the covers.

CONNECT ELECTRICAL

Verify that power is turned off at the source.

WARNING

If house wiring is not 2-wire with

a ground wire, a ground must be provided by the

installer. When house wiring is aluminum, be sure

to use U.L. approved anti-oxidant compound and

aluminum-to-copper connectors.

Ŷ 8VHZLUHQXWVWRFRQQHFWLQFRPLQJJURXQGWR

green, white to white and black to black.

Ŷ 3XVKZLUHVLQWRMXQFWLRQER[DQGUHSODFHFRYHU

Be sure wires are not pinched.

Screw

Duct Tape

Over Seam

and Screw

Air Flow

Duct Tape

Over Transition

White

Ground

Black

Remove

Junction Box

Cover

Insert Power

Conduit Thru

Strain Relief

and Tighten

Use UL Listed

Wire Nuts

18 49-80819

INSTALLATION PREPARATION

Installation Instructions

INSTALL FILTERS

Ŷ 3ODFHILOWHUGULSWUD\VLQWRWKHUHDURIWKHKRRG

Ŷ ,QVHUWWKHJUHDVHILOWHULQWRWKHRSHQLQJDQGGURS

into the trays.

Ŷ 7RUHPRYHWKHILOWHUVJUDVSWKHKDQGOHSXVKWKH

filter up and lift out.

49-80819 19

Notes

20 49-80819

Troubleshooting tips ... Before you call for service

TROUBLESHOOTING TIPS

Save time and money! Review the charts on the following pages first and you may not need to call for service.

Problem Possible Cause

Fan and lights do

not operate when the

switches are turned on

Ŷ The hood was never electrically connected by the installer/ electrician/builder. Call the

electrician/installer/builder to complete the installation. This is not covered by warranty.

Ŷ A fuse may be blown or a circuit breaker tripped. Replace the fuse or reset the circuit breaker.

The blower does not

work but the lights do

Ŷ The blower motor wire harness was not connected or was not connected properly by the

installer/electrician/builder to its mating connector located inside the hood on the top surface, to

the left of the blower assembly.

1. Switch power off at service panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

2. Remove the filters and locate the blower wire harness connector. Is it plugged into its mating

connector?

3. If no, plug the blower motor connector into its mating connector on the top of the hood. Switch

the power back on. Check to see if the fan now works.

4. If no, check the circuit breaker/fuse. If it is blown/tripped, replace/reset it. Does the blower

work now? If no, call GE Appliances for service.

The blower fails to

exhaust the smoke/

steam/ odors adequately

Ŷ Many factors could be the root cause for reduced air-flow.

1. Installation could be the problem: Your hood was designed to meet specific ducting

requirements. If your duct length exceeds the manufacturer’s requirements, hood performance

will suffer. Air-flow will also be reduced if the house duct work is too small or there are too

many elbows in the system. Contact your installer or builder.

2. Obstruction in duct work could be the problem: Make sure nothing is blocking the vent (bird

nests or kinks in the duct work).

3. Damper blade may not be opening: Make sure the tape is removed from the damper blades

and that it swings open freely.

4. Damper blade on Wall or Roof Cap may not be opening: Contact your builder so they can

make sure the damper swings open freely.

5. Dirty filters/baffles: Make sure filters (and all hood surfaces) are kept clean of grease and dirt.

6. Check to be sure the filter is clean: If replacing the filter does not correct the problem, call for

service.

7. Sufficient makeup (replacement) air is required for exhausting appliances to operate to rating.

Check with local building codes, which may require or strongly advise the use of makeup air.

Visit GEAppliances.com for available makeup air solutions.

Page is loading ...

GE CV48SSL1SS User manual

Brand: GE

Model: CV48SSL1SS

Category: Cooker hoods

Type: User manual

Download PDF

report

in other languages

español: GE CV48SSL1SS Manual de usuario

GE CV48SSL1SS User manual

GE CV48SSL1SS User manual

in other languages

Related papers

Other documents