Metra Electronics 99-3309B-LC User manual

Brand: Metra Electronics

Model: 99-3309B-LC

Category: Car kits

Type: User manual

INSTALLATION INSTRUCTIONS FOR PART 99-3309B-LC

APPLICATIONS

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 4/19/2013 INST99-3309B-LC

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

• A) Radio Trim Panel • B) Radio Brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws • E) (10) White Plastic Panel Clips

• F) Interface • G) 4-pin to 44-pin harness

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Interface included Antenna Adapter: • 40-EU55 antenna adapter

• Panel removal tool • Phillips screwdriver

• Small flat-blade screwdriver

TOOLS REQUIRED

Chevrolet Spark 2013-up

99-3309B-LC

B C

F G

D E

Table of Contents

Dash Disassembly

– Chevy Spark 2013-up .......................................... 2

Kit Assembly

– ISO radio provision with pocket ............................ 3

– DDIN radio provision ............................................ 4

Interface Installation

– Wire connections ................................................. 5

• ISO DIN and DDIN radio provisions

• Painted Matte Black

• AXXESS Interface included

•Providesaccessory(12volt3amp)andretained

 accessorypower

•Retainsallwarningchimes

99-3309B-LC

1. Unclip and remove the radio trim

panel. (Figure A)

2. Remove (4) Phillips screws

securing the factory radio and

remove from dash. (Figure B)

3. Unclip and remove the vents from

the factory panel. (Figure C)

4. Unclip and remove the hazard

button from the trim panel.

(Figure C)

5. Remove (5) Phillips screws

securing the upper display shroud

from the factory panel. (Figure C)

Continuetokitassembly

Dash Disassembly

(FigureA)

(FigureC)

Step 3

Step 5

Step 4

Step 5

(FigureB)

99-3309B-LC

Kit Assembly

ISO DIN radio provisions

1. Attach the factory vents and hazard

button to the Metra trim panel. (Figure A)

2. Attach the upper display shroud the

Metra trim panel with the factory screws.

(Figure A)

3. Attach the provided (10) panel clips to the

legs of the Metra trim panel.

4. Locate the factory wiring harness in

the dash. Metra recommends using

the proper mating adapter from Metra

or AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

5. Attach the radio brackets to the

aftermarket radio using the screws

supplied with the radio, then secure the

assembly to the pocket using the (4)

#8 x 3/8” Phillips screws. (Figure B)

6. Mount the assembly into the sub-dash.

7. Reassemble dash in reverse order of

disassembly using the Metra trim panel

instead of the factory trim panel.

(FigureB)

(FigureA)

Step 2

Step 1

Step 2

99-3309B-LC

Kit Assembly

DDIN radio provisions

1. Attach the factory vents and hazard

button to the Metra trim panel. (Figure A)

2. Attach the upper display shroud the

Metra trim panel with the factory screws.

(Figure A)

3. Attach the provided (10) panel clips to

the legs of the Metra trim panel.

4. Locate the factory wiring harness in

the dash. Metra recommends using

the proper mating adapter from Metra

or AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

Attach the radio brackets to the

aftermarket radio using the screws

supplied with the radio,

then mount the

assembly into the sub dash. (Figure B)

6. Reassemble dash in reverse order of

disassembly using the Metra trim panel

instead of the factory trim panel.

(FigureB)

(FigureA)

Step 2

Step 1

Step 2

99-3309B-LC

6. Connect the White/Black wire to the radios left

front (-) speaker wire.

7. Connect the Gray wire to the radios right front (+)

speaker wire.

8. Connect the Gray/Black wire to the radios right

front (-) speaker wire.

9. Connect the Green wire to the radios left rear (+)

speaker wire.

10. Connect the Green/Black wire to the radios left

rear (-) speaker wire.

11. Connect the Purple wire to the radios right rear (+)

speaker wire.

12. Connect the Purple/Black wire to the radios right

rear (-) speaker wire.

Installing the Interface

1. Plug the interface into the vehicle and into the

radio.

2. To initialize the interface, turn the ignition on and

wait for 30 seconds, then turn the ignition back off,

and on again.

CAUTION: Metra recommends disconnecting

the negative battery terminal before beginning

any installation. All accessories, switches, and

especially air bag indicator lights must be plugged

in before reconnecting the battery or cycling the

ignition.Note: Refer to the instructions included

with the aftermarket radio.

Use Metra’s 99-3309G to retain ONSTAR, steering

wheel audio controls, or control of the vehicle

customization menu.

Interface harness:

1. Connect the Yellow wire to the radios constant/

memory wire.

2. Connect the Red wire to the radios accessory wire

(a relay is needed if connecting more to this wire

than just the radio).

3. Connect the Black wire to the radios ground wire.

4. Connect the Blue wire to the radios amp turn on.

5. Connect the White wire to the radios left front (+)

speaker wire.

Wire connections to be made

Testing the Interface

1. Turn the ignition on then turn the radio on and test

for proper balance and fader operation.

2. Close all the doors then turn the key off. The radio

should stay on until the driver’s door is open.

Page is loading ...

INSTALLATION INSTRUCTIONS FOR PART 99-3309B-LC

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 4/19/2013 INST99-3309B-LC

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians

Page is loading ...

INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-3309B-LC

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 4/19/2013 INST99-3309B-LC

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recomienda técnicos

con certificación del Programa

de Certificación en Electrónica

Móvil (Mobile Electronics

Certification Program, MECP).

EL CONOCIMIENTO ES PODER

Mejore sus habilidades de instalación y fabricación

inscribiéndose en la escuela de dispositivos electrónicos

móviles más reconocida y respetada de nuestra industria.

Regístrese en www.installerinstitute.com o llame al

800-354-6782 para obtener más información y avance

hacia un futuro mejor.

Metra Electronics 99-3309B-LC User manual

Brand: Metra Electronics

Model: 99-3309B-LC

Category: Car kits

Type: User manual

Download PDF

report

in other languages

español: Metra Electronics 99-3309B-LC Manual de usuario

Metra Electronics 99-3309B-LC User manual

Metra Electronics 99-3309B-LC User manual

in other languages

Related papers

Other documents