Smarter Access Control
Quick Start Guide
1
Pre-installation checklist
Ensure your customer has an Alarm.com account
with a service plan that supports Access Control.
Mount and wire all system hardware according to
manufacturer’s installation instructions.
One or more controllers
ADC-ACC1-17 Door Controller
ADC-ACC2-34 Two Door Controller
ADC-ACX1 and ADC-ACX2 expansion modules (optional)
Up to eight expansion modules can be added to
the ADC-ACC1-17
Up to sixteen expansion modules can be added to
the ADC-ACC2-34
Power source
External power supply (included in ADC-ACC1-17-PSE
Door Controller and Power Kit and ADC-ACC2-34-PSE
Two Door Controller and Power Kit)
PoE (Power over Ethernet) connection (only available
with the ADC-ACC1-17 Door Controller)
• Wiegand readers or keypads
• Electric strikes, mag locks, or other electrified
locking hardware
• Request-to-exit devices
• Door position switches
• Other peripherals
• Cards, fobs, or other access credentials
• Internet access using an Ethernet cable
2
3
Control 1 supervised and 1 unsupervised reader with
the ADC-ACC1-17 Door Controller.
Control 2 supervised readers with the ADC-ACC2-34
Two Door Controller.
❶ ADC-ACC1-17 or ADC-ACC2-34
❷ Reader
❸ Reader
For detailed wiring guides, please see the device installation manuals.
Add up to 8 expansion modules to the ADC-ACC1-17 to
control up to 17 readers.
❶ ADC-ACC1-17
❷ ADC-ACX2
❸ ADC-ACX1
❹ Reader
❺ Reader
❻ Reader
❼ Reader
4
5
Add up to 16 expansion modules to the ADC-ACC2-34 to
control up to 34 readers.
❶ ADC-ACC2-34
❷ ADC-ACX2
❸ ADC-ACX1
❹ Reader
❺ Reader
❻ Reader
❼ Reader
Reader
For detailed wiring guides, please see the device installation manuals.
*You may add up to 68 readers on a single account.
Add hardware to Alarm.com account
Controllers
1. Disconnect any Ethernet cables from all controllers
in the system.
2. Navigate to the Access Control tab on the
Equipment page on the Partner Portal.
3. Add a controller using the “Add Controller” button.
Follow on-screen instructions. You’ll need the
controller’s MAC address, which is located on
the side of the Ethernet port.
4. Repeat for all additional controllers in the system.
5. To add an expansion module to a controller,
click the “Add Expansion Module” link displayed
next to the controller in the Controllers table.
Follow on-screen instructions.
6. Repeat for all expansion modules in the system.
Doors
7. To add doors to a module, click the “Add Door” link
displayed next to the module in the Devices table.
Follow on-screen instructions.
8. Repeat for all doors in the system.
Check connection
9. Connect an internet-connected Ethernet cable
to each controller and power up the system.
10. Check the Event History on the Partner Portal to
make sure the controller is communicating.
6
7
Add card formats to account
11. On the Access Control tab on the Equipment page,
click “Manage Card Formats.”
12. If you know the card format and facility code,
click “Add Known Format” and follow the
on-screen instructions.
13. If you do not know the card format or facility code,
click “Add Unknown Format” and follow the
on-screen instructions.
14. Repeat steps 12 and 13 for all card formats you plan
to use with this system and click “Save.”
To add or manage Users, Access Plans, and Timetables,
navigate to the User Access tab on the Customer
Website or Mobile App.
Questions?
Visit alarm.com/supportcenter
8
8281 Greensboro Drive
Suite 100
Tysons, VA 22102
190314
© 2019 Alarm.com. All rights reserved.
Made in China.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Alarm.Com ADC-ACX1 Quick start guide
-
Legrand PW1020 User guide
-
Broadcom ACPL-798J Evaluation Board Kit (PMOD Type 1 Interface) Isolated Sigma-Delta Modulator User guide
-
-
ALARM COM ADC-VC727P Installation guide
-
ELECRAFT KX3 Owner's manual
-
-
-
-
GE superbus 2000 concord 4 gsm module User manual